Search Documents

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

By A. Sinha, N. K. Babar, H. R. Kalihari, A. K. Chakraborty, M. R. Saharan, C. P. N. Pathak

A case study is presented on the optimization of cable bolting patterns in cut-and-fill stopes at the Chikla Mine, MOIL, India. Rock mass characterization, using Bieniawski’s RMR and Barton’s Q, indicated that the stopes lie in the “no supports required” to “spot bolting required” support categories. In contrast, the current practice of cable bolting in a 2.0 m by 2.0 m grid pattern for stope widths less than 12 m displays different results. Numerical modelling results are in line with the rock mass characterization study. It can be affirmed, as well, that no cable is carrying rock loads greater than 5 t. This fact is derived from observational behaviour of the crown pillar of an experimental stope with open stoping operations and hanging cables in the cut-and-fill stopes of the mine. An increase in the cable bolting grid spacing is, hence, recommended for implementation by mine management, based on the study described in subsequent sections. It is also suggested that the mine adopt the open stoping method, provided results of a rock mechanics instrumentation program in an experimental stope with a cable bolting grid of 2.5 m square are favourable.

Jan 1, 2007

By Frank B. Amon

Highland Valley Copper had to make some significant changes in the way it was working in order to counter the effects of ever-increasing costs and decreasing metal prices. A mine/mill optimization plan started in 1997 introduced new technologies and management approaches that resulted in a dramatic drop in cash breakeven costs. The changes involved employee training, added authority and responsibility for staff, better communications, and a consistent approach to setting and achieving property-wide goals. The net effect was to change the culture of the organization from one that was fragmented and focussed on local objectives to one that is cohesive and has common goals. These changes have allowed the mine to remain in business during a protracted period of low metal prices, and have positioned the mine favourably to benefit even more from any future increase in prices.

May 1, 2004

By M. C. Pietrobon

"A common problem in assessing the applicability of laboratory flotation data is determining how closely conditions during laboratory testing of the ore matches those that occur in a plant. Typical laboratory based investigations do not consider factors such as water quality, pulp temperature and the pulp chemical environment during both grinding and conditioning on laboratory flotation performance. Disregarding these important factors may seriously compromise the validity of conclusions based solely on laboratory experimental results. Furthermore, considering these factors during the flowsheet design stage in the development of new ore resources may reduce financial risk associated with building a new plant. A methodology is described here which embraces these factors in an attempt to bridge the gap between laboratory and plant. The methodology should be considered a vital first step in all laboratory based experimental programs and has implications for fundamental studies on the flotation behaviour of single minerals. This methodology increases the confidence with which findings of laboratory based studies can be transferred to the plant and highlights the effect of variables which may be accessible to manipulation in the plant.Pulp chemical parameters, such as pulp dissolved oxygen demand, pH, Eh, mineral oxidation and solution composition were manipulated in the laboratory by adjusting the duration of gas purging after grinding, the process water input and pulp temperature. A key finding was that matching of the laboratory pulp chemistry to the plant pulp chemistry was dependent upon oxidation after grinding. In turn, mineral oxidation was dependent upon the pH in grinding, water composition and the duration of oxygen purging after grinding. The methodology closely matched the dissolved oxygen demand and surface chemistry of laboratory and plant pulps."

Jan 1, 2002

By Wendy L. Naysmith

This paper deals with the various options considered and factors that influenced the final selection of the headframe, shaft layout and hoisting systems required at the Impala No 16 Shaft in order to hoist both the required 3 Mt of ore per annum, and transport men, material and equipment between the surface and the underground workings to a depth of 1640 m. The layout and construction method used for what is at present the world?s tallest concrete headframe is discussed together with the integrated hoist room foundations designed to suit multiple mechanical and electrical hoist supplier?s solutions. The mechanical components of the two tower mounted 6,5m 4 rope Koepe hoists and deflection sheaves and their layout is dealt with in detail. Various features of the bearing type, brake units and brake control system are also discussed. Installation of the mechanical and electrical hoist equipment in the headframe took place during the sinking phase of the project and placed severe restrictions on the use of the heavy lifting facilities. This required a well-managed and systematic approach to delivery of the hoist components and associated equipment, as well as close co-operation between all contractors on site.

Oct 1, 2010

By Francis Chachula, Niel Erasmus

"In 2002, Titanium Corporation Inc. focused its attention on the development of a process for the recovery of valuable heavy minerals, including zircon and titanium bearing minerals from oil sands froth treatment tailings. The development of a process flowsheet to recover the titanium and zircon minerals from the Athabasca oil sand tailings has evolved through many laboratory, bench and pilot scale iterations.Initial development work focused on so-called ‘beach sand’ material, which is tailings material deposited over a period of time close to the tailings pipe discharge. The derived process flowsheet primarily consisted of gravity concentration stages, which is typical of all mineral sands operations. Titanium Corporation’s business plan calls for the utilization of tailings directly from the tailings pipeline – the process developed around the beach material is therefore risky as it differs from the live tailings in a number of aspects, with the effects on the process unknown. Titanium Corporation successfully obtained an intermediate product through a ‘bulk sampling plant’ coupled directly to an Oil Sands operator’s froth treatment tailings pipeline, during the summer of 2005. Subsequent further processing of this material resulted in poor separation or concentration of the heavy minerals due to a number of reasons. A more effective process flowsheet had to be developed.The newly derived process is basically a marriage between mineral sands technology and oil sands technology that can economically concentrate and recover the heavy minerals and entails the incorporation of a flotation process that takes advantage of the entrained bitumen in the feed to separate the heavy mineral fraction from the quartz gangue This paper will describe the newly derived process as well as the successful results of a subsequent on-site concentrator pilot campaign completed during the 3rd Quarter of 2006."

Jan 1, 2008

By S. A. H Tyrrell, R. Rotzinger

"Taseko Mines Limited recommenced operation of the Gibraltar copper-molybdenum mine in 2004 and embarked on series of development projects to modernize the mine and increase throughput capacity. The Gibraltar Development Plan 3 (GDP3) project included a second stand-alone copper-molybdenum concentrator, a stand-alone molybdenum separation plant and associated services. Ausenco was contracted to commence the detailed design in 2Q2011, commissioning commenced in 4Q2012 and first ore was processed in 1Q2013. This paper discusses the design, implementation and commissioning of the GDP3 Concentrator.INTRODUCTION The Gibraltar Mine (Gibraltar) property is located in the Cariboo Region of south central British Columbia, approximately 360 kilometers northeast of Vancouver. The site is accessed via an 18 kilometer paved road from the town of McLeese Lake, which is located on the province’s main north-south highway between the cities of Williams Lake and Quesnel. Gibraltar was originally developed by Placer Development and commenced production in 1972. Gibraltar was acquired, while on care and maintenance, by Taseko Mines Limited (Taseko) in 1999 during a period of unusually low metal prices. Taseko recommenced operations at Gibraltar in 2004, and embarked on series of development projects to modernize the mine and increase throughput capacity. The 1972 Gibraltar process flowsheet incorporated two-stage crushing followed by rod and ball milling and flotation. In 2008 Gibraltar completed their first development stage that included the installation of a SAG mill, converting the existing rod mills to ball mills and adding additional flotation capacity. Gibraltar continued development with the installation of an in-pit primary crusher, expansion of the bulk regrind circuit, expansion of the cleaner flotation circuit, replacement of the tailings pumping system and replacement of the concentrate filters and dryer."

Jan 1, 2014

Vale Inco?s Coleman Mine 153 Orebody is a narrow vein deposit with a dip that varies from 30 to 70 degrees. It has a strike length of 1200-feet and the current mining extends from the 4250 level to 5100 level. The primary mining method is mechanized cut-and-fill although drift-and-fill is also used in wider sections of the ore zone. The ore body is divided into six main mining horizons with an average of three mining blocks on each cut. There are some interesting rock mechanics challenges related to mining upward from the 4550 level and these challenges are increasing as the mining front progresses toward the 4400 level. The mining of the 4550 block is currently at cut 13 whereby the crown pillar thickness is approximately 60-feet. Significant factors including increased stress levels in the crown pillar, the change in the orebody dip at this level and a recently indentified geological structure in the footwall, have all combined to introduce seismic activity in the footwall of 4550 level. Closer studies revealed a consistent trend of seismicity that was further examined with core logging and Acoustic TeleViewer technology. The data from these assessment tools disclosed a geological structure that is influencing the mining environment. This paper reviews the seismic analysis for the 4550 level mining zone and the subsequent procedures used to locate the new geological structure. The paper also discusses the key mining practices used to successfully mine cut 13 of 4550 level and briefly reviews the studies that are underway to up-date the mine design for continued extraction of high-grade ore in a safe and productive manner.

May 1, 2009

By Olli Haavisto, Juha Timperi

"Accurate on-line assays of mineral slurries are the basis for effective operation of flotation circuits. Typically the elemental content measurements are obtained by an X-ray fluorescence (XRF) analyzer, which samples the process lines and performs the analysis concurrently line-by-line. For a more frequent measurement of each slurry line the XRF measurements can be complemented with reflectance spectrum information. In reflectance spectroscopy the absorbance properties of the slurry in the visible and near-infrared wavelength range are analyzed. The advantage of reflectance spectroscopy is that measurements can be obtained quickly and simultaneously from several slurry lines. However, since the shape of the spectrum is only indirectly affected by the slurry elemental contents, frequent calibration of the measurement against the XRF analyzer is necessary. This study elaborates the combination of reflectance spectrum analysis with XRF. Results of laboratory tests for different slurries are presented and the operation of the system in a copper-zinc flotation plant is demonstrated.IntroductionElemental analysis of mineral flotation slurries is the most important factor in evaluating the performance of concentration processes. Timely on-line assays are also used as the basis for controlling the circuits and ensuring that the grade and recovery targets are reached. X-ray fluorescence (XRF) is the dominant technology in on-line elemental slurry analysis, and typically centralized XRF analyzers are used. The advantage of a centralized analyzer is that one measurement probe can be used to acquire the data from several slurry lines. This reduces the overall operating cost of the system when compared to distributed analyzer system design with several measurement probes requiring maintenance and spare parts. Slurry samplers are installed in the interesting process flows and representative sample flows are brought to the analyzer, where the slurry is further sampled and measured consecutively by the XRF analyzer. Due to the centralized structure of the analyzers and consecutively measurement of the sampling lines the sampling interval per slurry line can be relatively long. In larger concentration plants with several sampling lines a typical assay interval is in the range of 10-20 minutes."

Jan 1, 2016

By Persio P. Rosario

Crushing has proven to be of fundamental importance in mine mill integration at Highland Valley Copper (HVC). Highland Valley Copper has achieved large throughput and good quality control through the gyratory crushers by proper blast design and better gap control. The next step, in optimizing the mine mill relationship, is evaluating the crusher liner wear and its shape influence on performance and product size reduction. To do this a laser measurement device has been developed and data is being recorded on the concave and mantle liner wear. This paper will outline the work to date and indicate specific objectives of the work.

May 1, 2002

By Oy Leuangthong

The McMurray formation in the Athabasca oil sands deposits of Northern Alberta is part of the world?s second largest proven crude oil reserves. The formation is characterized by stratigraphic layers that correspond to three different depositional environments: Marine, Estuarine and Fluvial facies. Resource estimation for oil sands has traditionally relied on polygonal and inverse distance schemes. These techniques are simple and straightforward in practice, but they do not permit reliable uncertainty assessment. This paper describes the modeling of the McMurray formation using modern geostatistical techniques. Geostatistical modeling should be performed within homogeneous geological facies. The methodology for geostatistical simulation within each of the identified facies involves: (1) assessing the most appropriate stratigraphic transformation for optimisation of the correlation structure, (2) determining representative distributions with declustering and debiasing techniques, (3) modeling spatial continuity of the bitumen grade, fines grade, water saturation and other petrophysical variables, (4) performing estimation and cross validation as checks against simulation results, (5) performing simulation for uncertainty quantification of bitumen and fines grade, and (6) model checking of simulation results against the input data and comparisons against the kriged models. These steps are described in detail. The application of these models for uncertainty quantification in support of resource classification is also discussed.

May 1, 2004

Peñasquito is Mexico's largest gold producer, consisting of two open pits - Peñasco and Chile Colorado - containing gold, silver, lead and zinc. Over the next three years, mining activities in the pit are expected to be focused on lower grade ore in the upper parts of the Peñasco pit while stripping is emphasized to ensure an economically optimal pit shell design to maximize the net asset value of the operation. By 2019, Peñasquito’s gold production is expected to benefit from an improvement in mined grades as it recommences mining higher grades at the bottom of the Peñasco pit and significantly enhanced metallurgical recoveries with the planned completion of the Pyrite Leach Project ("PLP").

Jan 1, 2017

By C. H. Lee, K. Adham, D. Lemieux, J. P. Mai, A. M. S. Hussein, S. Francey

Copper concentrates contain an increasing amount of arsenic, as the older sources of cleaner ores are depleted. At the same time, the market-determined price penalties on arsenic rich concentrates are rising due to limited arsenic treatment capacity at smelters and increasingly stringent environmental emissions limits, necessitating arsenic removal from the copper concentrates. Heating the concentrate to about 700°C can remove significant amounts of arsenic (as elemental and/or sulfide); however, it is important to achieve that removal economically and with due consideration to post-roasting arsenic (toxic waste) treatment. A comparison is made among different roasting options (kilns, multi-hearths and fluid beds) to qualify their potential application to arsenic roasting of copper concentrates. Both direct and indirect methods of heating as well as inert, air and oxygen atmosphere options are considered. Technology comparisons are made with respect to the roaster’s operation, its off-gas treatment and arsenic stabilization. INTRODUCTION In the last twenty years, the arsenic content in globally produced copper concentrates have risen steadily due to the depletion of cleaner ores and the increase in complex concentrate production. Smelter contracts typically limit arsenic to less than 0.5wt%, with a penalty paid per unit of additional arsenic and other contaminants such as antimony. While penalties can vary, they can be on the order of $70/dry metric tonne of concentrate per 1% of arsenic. Strategies used by miners to avoid the price penalties have been to blend clean and complex concentrates, and to remove arsenic from complex concentrates to achieve smelter limits. Arsenic can be removed from copper concentrates by the heat-induced decomposition of the predominant enargite mineral (Cu3AsS4) at ~700°C. Roasting at such elevated temperature is a commercially proven option, but still suffers from process, cost and environmental challenges. After roasting, the released arsenic sulfide fumes can be separated from most of the entrained concentrate dust in cyclones. Then, the As2S3 laden off-gas can be oxidized to generate a still volatile oxide (As2O3), which can be further separated from the residual concentrate dust in a hot electrostatic separator. Next, the off-gas can be cooled with air or water, to either deposit the arsenic oxide in a dry or dissolved state. Dissolved arsenic acid can be oxidized to As(V) and reacted with iron to yield a stabilized ferrihydrite precipitate or scorodite that can be safely disposed. In the case of dry arsenic trioxide, it can be mixed with reactants (e.g. iron) and fluxes before thermal stabilization in a glass matrix, thus eliminating the need for costly oxidation.

Jan 1, 2019

By Dave Rose, Jacques McMullen

"The Detour Lake mine is located 200 km northeast of Timmins, Ontario, Canada.The mill processes a free milling gold ore using both a gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 tpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The Detour Lake mine has one of the largest gyratory crusher in the world (60"" x 113"") and over the years, many improvements have been made to this crusher with the result of improving plant throughput. This paper will present how choke feeding the gyratory crusher has been found to be one of the main influences on crusher product particle size and plant throughput. It will explain how the effect of choke feeding the gyratory was measured and from that, the various changes made to improve choke feeding of the gyratory crusher.IntroductionOre is hauled from the open pit mine and dumped directly into a single 60"" x 113"" primary gyratory crusher. The live capacity of both the feed and discharge hoppers of the gyratory crusher are designed for two (2) truck loads each, assuming a nominal payload of 300 tonnes per truck. The surge bin under the primary crusher feeds an apron feeder that controls the ore feed rate at approximately 4,200 tph onto a 227 metres long x 1.52 metres wide belt conveyor with a nominal capacity of 4,200 tph.The primary crusher is operated at an open side setting of 172 millimetres to produce a F80 feed to the secondary crushing circuit of 135 millimetres."

Jan 1, 2017

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003

By J. Allaire, P. N. Muteb

The Meadowbank mine is operated by Agnico-Eagle Mines Ltd. and is located in the Kivalliq District of Nunavut in northern Canada. The process plant operates presently at a throughput of 11,500 tpd with gold grade varying between 2.9 and 3.6 g/t. The ore supplied to the process plant come from two different open pits and it expected to come from a new open pit early 2014. The ore is mid-hard materials so the feed size ore have a bigger impact on the throughput. The average gold recovery is 94.0% with about 15-30% of gold recover from the gravity circuit. The Meadowbank mine commissioning started in February 2010 utilizing a flowsheet consisting of one stage of crushing followed by primary and secondary grinding. The commercial production began in March 2010. During the commissioning several difficulties were observed to reach the designed throughput of 8,500 tpd. It was evaluated to insert a second stage of crushing. The insertion of the secondary crushing have two objectives, first to reach easily the process plant design throughput as well as to evaluated the mill capacity increasing. The process plant team evaluated various expansion alternatives eventually deciding to install a secondary crusher, increased the SAG and Ball mills motors capacities and maintain the rest of the process unchanged. Early 2011, with the improvement in the gold markets, decision was made to install the secondary crusher between the primary crusher and the primary grinding. The process plant continued to operate on the initial design until early June 2011. This paper presents the SAG mill throughput increasing from the designed tonnage of 8,500 tpd to 2012 targeted tonnage of 11,500 tpd, secondary crusher commissioning and the difficulties to operate in Canada Artic (Nunavut).

Jan 1, 2013

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By Donald Leroux, Asim Tuzun, Simon Gariépy, Luc Lachance, Hayley Halsall-Whitney

"The importance of coherent material balance results has long been recognized by mining and metallurgical companies. Although this is still true nowadays, various stakeholders are increasingly concerned about the origin and the accuracy of the reported numbers. The last decade has shown that most metallurgical accounting concerns can be addressed by making two important changes to plant performance monitoring practices. First, introducing data redundancy into the metal balance procedure allows the estimation of measurement errors. Second, the migration from spreadsheet-based to relational database based systems brings transparency, data integrity, traceability and auditability into metallurgical accounting. Relational databases also facilitate the production of reports that metallurgical accountants must issue routinely. Recognizing the caveats of the spreadsheet-based metal accounting method they had been applying for years, Strathcona decided to switch to a commercial relational database system in 2008. For the most part, the migration was seamless. Some challenges were raised but they could all be overcome and outweighed by benefits gained from day-to-day utilization of the system.INTRODUCTION Metal accounting (Morrison, 2008) has always been essential to high-quality corporate governance of mining and metallurgical companies. Although the importance of coherent material balance results has long been recognized, various stakeholders are increasingly inquisitive about how the reported numbers were obtained and how much accuracy can be attributed to them. This accrued scrutiny is obviously no stranger to the corporate governance tightening that happened through the years in response to outrageous accounting scandals. It is also in continuity with securities laws (such as NI-43-101 in Canada) that were passed to protect the public from other market fraud. Recognizing the importance of spotless metal accounting in their reports to the public, a group of global mining companies gave AMIRA International the mandate of developing a set of rigorous yet practical metal accounting guidelines for the mining and metallurgical industry. The AMIRA P754 project was launched in 2004 and the first version of the resulting Code of Practice was released the following year. Since then, the Code was reviewed twice and revised releases were issued (AMIRA, 2007). While some parts of these guidelines are in continuity with current commonplace practices, other parts recommend changes to inherited practices that may be significant. For example, they highlight the importance of data redundancy (Lachance & Flament, 2011) which in many operations is either already available but unexploited or achievable with reasonable efforts. These guidelines also stress the importance of state-of-the-art metal accounting systems, such as those based on relational databases, which are secure and entirely auditable by a Qualified Person. Because most spreadsheet software packages allow data and formulae to be modified at any time, without a trace and anonymously, they do not meet these requirements."

Jan 1, 2012

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

"More efficient drilling and blasting techniques have shown measurable improvements in throughput at the Barrick Goldstrike wet grinding mill.A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas participated closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of improving throughput in future years, despite the projected harder ores. Plant studies were conducted to determine if adjustments to drilling and blasting could positively influence throughput. At the Goldstrike mill the greatest opportunity from the D2M initiative is realized on the hardest ore. Grinding throughput for softer ore, <15 kWh/st, can meet or exceed the downstream pressure oxidation requirements. Grinding throughput for harder ore, >15 kWh/st, is limited by the SAG milling capacity. Better fragmentation in the D2M ore, as demonstrated by image analysis, increased throughput 5% to 10% (25 to 50 stph) compared to the standard mining methods.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of:1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots.2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy.3) Improved distribution of the explosives by decreasing pattern spacing.INTRODUCTIONThe Barrick Goldstrike Open-Pit group, along with the Process division, began experimenting with novel blasting technology and techniques to improve mill throughput in the spring of 2001. A series of tests were developed to determine if fragmentation and ultimately mill throughput could be influenced by optimizing the drilling and blasting program in known"

Jan 1, 2004

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017