Search Documents

By E. Godin, M. Rigaud, S. C. Panigrahy, I. Malinsky

"RésuméDes boulettes de concentres d'hématite spéculaire à basse silice ont été produites en substituant la bentonite par de la tourbe, adéquatement traitée, additionnée d'une faible quantile de soude caustique durant le boulettage. La réductibilité de telles boulettes et leur gonflement pendant la réduction ont été évacues, en utilisant quatre mélanges gazeux différents, formes de H2 - CO - N2.L'influence du pouvoir réducteur du gaz utilise, sur le gonflement des boulettes, à été mis en évidence. Quelles que soient ces conditions réductrices, les propriétés mesurées sur les boulettes liées a la tourbe sont comparables aux propriétés obtenues avec des boulettes traditionnelles liées à la bentonite.ABSTRACTAdditions of peat moss and small quantities of NaOH during balling of low silica specular hematite concentrates have eliminated the need to use bentonite as a binder. The reducibility and swelling of such pellets have been evaluated using four different gas mixtures, consisting of H2 - CO -N2. The influence of the reducing power of the gases, on the swelling behaviour of pellets has been documented. Under the different reducing conditions, this new type of pellets exhibit properties similar to the ones obtained using bentonite."

Jan 1, 1987

By B. Calver, D. J. M. Farnsworth

"As open-pit operations expanded at Pine Point, hydraulic aquifer evaluation was undertaken to establish the criteria necessary for the design of a feasible dewatering system.The extreme climate of this northern location dictated that the ore zone under extraction be rendered as dry as possible to minimize freezing effects. The design and implementation of such a system necessitated detailed hydraulic evaluation, and the problems that occurred are typical of those inherent in open-pit mining operations in northern areas.The paper describes the problem solution as approached from a mine engineering point of view, with particular reference to the practical aspects of operation and installation. The hydrological analysis used is simple and readily applicable to most open-pit dewatering problems."

Jan 1, 1969

By G. R. Elliott

Foreword The office of the Supervisory Mining Engineer, a branch of the l. Federal Government, is financially interested in no oil company and has no stock to sell. This office, however, is deeply interested in the proper and efficient development of Canada's natural resources. The people of Canada are interested in the petroleum development in Turner Valley for two principal reasons: As represented by the Department of the Interior, they are the largest owners of petroleum and natural-gas rights in the field; As a nation, they are vitally interested in the development of petroleum and natural gas as a national asset, and therefore, also, in all productive property, no matter who directly controls the leases. As has been stated by Mr. Charles C. Ross, Supervisory Mining Engineer, "The Department, being responsible for the administration of these public resources, necessarily requires regulations to protect them from abuse by lessees. Our portion of this responsibility is to record a complete history of all drilling operations and to see that proper drilling methods are adopted to prevent damage and wanton waste of the valuable natural resources under discussion." Not only does our position necessitate an impartial and a judicial viewpoint, but, being day by day in touch with all operations in the western provinces, we are uniquely situated to comprehend both individual and general problems.

Jan 1, 1930

By Dennis Hoffmann

"Abstract - Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa , were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, Al, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/Al, Si/Fe, Fe/Mn, La/Ce and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnet­ and amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+ Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By N. Campbell, W. T. Orvine

The metalliferous deposits of British Columbia are largely confined to that portion of the Cordilleran province lying west of the Rocky Mountain trench. Massive sulphides in the coastal area carry important copper •values together with lead and zinc and are composed mainly of pyrite which replaces schists or shear zones. The massive sulphide ore of the interior, on the other hand, contains lead and zinc with little copper. Pyrrhotite rather than pyrite is... the dominant metallic and deposition took place through selective replacement of sedimentary beds.

Jan 1, 1960

By V. L. Eardley-Wilmot

Introduction We are all familiar with the bright and attractive colours of the roofs of our suburban houses and country cottages, but few of us fully appreciate the complex and highly technical nature of the business which produces these roofings. Roofing granules consist of small broken particles of certain types of rocks, burned clay products, or slag. They are used either in their natural state or artificially coloured and are affixed onto one surface of asphalt sheeting. Their main functions are to protect the roof against external fire hazard, prolong its life, and enable it to withstand extremes of weather over a period of years without deteriorating. Pleasing designs and colours are added attractions. The reverse, or inner side, of the sheeting is coated with a film of talc or fine mica to prevent it sticking when rolled up for convenience of handling for transport. The finished sheets or strips are cut into a variety of shapes for roofing shingles, or for sidings which resemble rows of bricks separated by mortar. In Canada, the consumption of roofing granules has increased fourfold in the past decade and indications are that the industry will continue to expand. At present, fourteen plants are engaged in manufacturing granule-coated roofings, but, apart from a relatively small output of natural granules by two producers in British Columbia, only one eastern producer makes both natural and coloured granules in Canada, and these only for its own use. The annual consumption is now over 77,000 tons of roofing granules valued at more than $1,600,000, but about 62 per cent of the tonnage is imported. It is thus apparent that the production of Canadian-made granules, both natural and coloured, could be considerably increased. This paper is presented in order to give an outline of the industry and at the same time to point out its difficulties and pitfalls.

Jan 1, 1946

By Ralph V. Stewart

"The asbestos orebody is contained within ultrabasic rocks of Precambrian age, being located in the continuous permafrost zone of the Quebec Ungava Peninsula, some 300 miles north of the tree line at approximate latitude 61'49' and longitude 73°58'.The asbestos deposit is at the western tip of a folded ultrabasic sill complex which trends northeast and covers an elliptical area 4.5 miles wide by 15 miles long. Locally. the asbestos occurs in. a completely serpentinized dunite rock. The principal rock types in the vicinity of the ore-body originally consisted of dunite, peridotite and pyroxenite, all of which have experienced at least two periods of alteration, so that no fresh rock now remains.The main ore zone in the open pit is approximately one quarter mile in length, 150 to 200 feet in width, and plunges at 25 to 30 degrees in a northeast direction below surface, to a vertical depth of at least 1,200 feet, Consider¬able tectonic activity resulted in favourable structural conditions which culminated in the formation of the ore zone in its present form.The deposit consists principally of cross-fibre ""gash type"" veins which vary in length from several inches to several feet. The principal fibre vein direction is parallel to the dip of the enclosing serpentinized dunite and sill complex.Some of the problems encountered during diamond drill¬ing in permafrost are briefly discussed."

Jan 1, 1976

By J. Basi, D. F. Rucker

"A review of historic operating practices of the heap leach pads at the Los Filos Mine, Mexico, revealed periods of restricted cyanide addition, reduced leach time, and insufficient irrigation flow. These issues all led to the buildup of partially leached recoverable gold inventory within the leach pads. Drawing down this inventory represented an opportunity to bring value forward. This paper outlines the strategic initiatives which were implemented as efforts to accelerate the inventory drawdown, including geophysical mapping and pressure injection.INTRODUCTION Los Filos is a heap-leach operation located in the Guerrero gold belt in southern Mexico. Operational and hydraulic challenges at the Los Filos Mine have led to a buildup of gold in inventory within the leach pads. Operationally, periods of restricted reagent addition, reduced leach time, and insufficient irrigation flow have compounded over the last eight years, and resulted in significant inventory growth. Hydraulically, the leach pad has issues with low permeability and solution channeling due to the fines and clay content of the ore. The leach pad is storing high-grade pregnant leach solution (PLS) as perched aquifers above areas that are compacted and difficult to drain. These operational and hydraulic challenges made it particularly difficult to spatially predict the precise locations of the inventory build-up. Fortunately, the challenges at Los Filos are not unique to the mine, and others have taken steps elsewhere to reduce metal inventory through a program that targets areas for inventory drawdown. For example, Ghorbani et al. (2016) noted that a method of injecting barren reagent solutions, applied directly to specific areas of a leach pad to reduce inventory, was presented by Wan and Brierley (1997) and Wan (1997). Seal (2004; 2007), Seal and Jung (2005), and Seal et al. (2012) have put the injection methodology into practice in Nevada and Colorado gold mines with a technology called Hydro-Jex®. The goal of Hydro-Jex has been to supply reagents at a high pressure over a short duration, followed by periodical low pressure rinse periods to remove leached metal and resupply fresh reagent to the ore."

Jan 1, 2017

By J. E. Hawley

This paper constitutes a report from the Committee on Geological Research to the Geology Division of the Institute. Two years have elapsed since a formal report was made containing several resolutions aimed at assisting geological research, a review of research equipment available, a summary of research projects suggested for consideration, and a list of research then in progress (see July, 1947, Bulletin, pp. 351-370). At this time we may note what action has been taken on the various resotions and suggestions of the Committee, indicate the more important accomplishments of independent investigators, and present a summary of the rather imposing volume and variety of research currently being carried on throughout the country. I.-Committee Resolutions and Suggestions 1.-A National Advisory Committee on Research in the Geological Sciences The original resolution adopted on the setting up of this Committee was approved with despatch by Council and was forwarded to the Minister of Mines and Resources. Due to a reorganization in the Department and possibly other reasons, no action on this important matter has yet been taken, but we are assured that some time this year such a Committee will be established by the Department of Mines and Resources. Unquestionably, it will give a fresh impetus to research in the geological sciences. When the noteworthy progress made by the research committees on Geophysics and on Soil and Snow Mechanics, established by the National Research Council, is considered, it is indeed regrettable that the Department of Mines and Resources has not acted more decisively in this matter.

Jan 1, 1949

By Mary A. Wells, Amir Hadadzadeh, Mark A. Whitney, Stephen F. Corbin

In an effort to produce less expensive titanium sheet via roll compaction, the room temperature compaction behavior of titanium sponge granules (99.9% pure, Alfa Aesar) was studied under uniaxial die compaction. The titanium sponge granules were irregularly shaped, with a high degree of porosity, having a maximum particle size of 3mm. Manual die compaction was conducted using a Carver hand press, in a hardened tool steel die with 12.61 mm inner diameter. Uniaxial die compaction in a hardened tool steel die with 9.50 mm inner diameter was also performed using a Gleeble® 3500 thermal-mechanical simulation testing system which allowed for controlled deformation rates. Compaction behavior of the titanium sponge was studied using well-established compaction equations (Heckel, Panelli-Filho and Ge), and it was observed that compaction rate influences the room temperature compaction behavior of this material. The Heckel analysis of the titanium sponge showed that the behavior of the material could be analyzed in two compaction pressure regimes. In the low pressure regime (<100 MPa) the granules exhibited high compressibility, while; in the high pressure regime (>100 MPa) lower compressibility of the titanium sponge was observed.

Jan 1, 2015

By K. A. Clark

"The repacked mineral aggregates of good grade oil sands have permeabilities ranging between 15 darcys to 350 millidarcys. The variation is due to the silt contents of the aggregates. Few good grade oil sands contain as much as 30 per cent •silt, most of them contain less than 20 per cent, and a large proportion have less than 10 per cent.The permeabilities of repacked good grade oil sands (oil included) depend on the degree of liquid saturation. When saturation with oil plus water reaches between 80-90 per cent, permeability is reduced to zero. As total saturation decreases below 80 per cent, permeability increases ranidly. Permeabilities of between one and two darcys were observed for total saturations between 60-70 per cent.The mean value for 18 measurements of the permeabilities of ""undisturbed"" core samples of good grade oil sands was 50 millidarcys. This value is •probably too high. The mean value for 20 measurements on core samples of interbedded oil sand and shale was 100 millidarcys. The mean value for 11 measurements on shale was 10 millidarcys."

Jan 1, 1960

By Nicholas C. Williams

This paper presents the development of a demand reduction and responsive strategy capable of reducing the electrical power demand, particularly during peak conditions. The work presented includes a case study of a UK colliery. Areas explained are the equipment installation at the mine; the development of the demand reduction strategy including the load profile database and prediction optimisation model. Some live production data from the power meter installation at the mine is also presented.

Aug 1, 2013

"Sedimented hydrothermal precipitates of silica, now fine-grained quartz, are described from a Pb-Zn-bearing vein system. Their discrimination from the wall-accreted fine-grained quartz that is common in the shallow parts of epithermal systems is discussed. Local fine-grained (<0.3 mm) quartz accumulations occur in a suite of veins with otherwise normal drusiform and crustified infills. This sediment may fill the vein above chokes in steep segments (axial plugs), or form continuous layers within the footwall material where the vein is inclined at low to moderate angles. Pads of fine-grained sediment are deposited on the upwards-facing surfaces of wall-rock clasts and of drusiform crystals growing from the vein walls. The asymmetry of these deposits differentiates them from the more common symmetrical, crustified walllining deposits of fine-grained quartz and opaline silica, and requires a gravity-controlled, sedimentary depositional mechanism.Thin section examination shows that much of the fine-grained quartz is present as elongate prisms. The prism habit was present soon after deposition, but it is not possible to identify unequivocally the original sedimented grains. Sedimentation of vein- and wall-rock-derived detritus is also recognized. Deposition of the fine-grained sediment accompanies normal in situ drusiform growth of quartz and other vein minerals. The mammilated and spherulitic textures associated with accretion of amorphous quartz are entirely absent from the Tyndrum veins with sedimented materials. The literature on modern hydrothermal waters and physical chemistry of silica precipitation shows that precipitates of silica suspended in hydrothermal fluids are amorphous and derived from colloidal silica. It is argued that much of the suspended silica was present as quartz at the time of deposition or was converted from amorphous silica almost immediately after deposition.Hydrothermal sediments and their distribution potentially provide information on flow directions and velocity in veins. Plugs of sediment obstruct vertical flow and lead to local flows with large horizontal components. It is shown that sedimentation features occur in other deposits and can involve other minerals. If the features seen here can be scaled up to the size of major veins, they may result in up and downdip variations in mineral assemblages and abundances, which may affect grade."

Jan 1, 2007

By L. D. van Dyk, G. S. Tshofu

Iron ore fines are by-products of iron ore mining operations. Unlike iron ore lumps, fines cannot directly be used in conventional iron making processes, and consequently large quantities accumulate around the world. Pelletizing and sintering can be used to convert iron ore fines into agglomerates or briquettes for processing with lump ore, but these techniques are energy intensive and produce greenhouse gases. This research investigated the extraction of iron from iron ore fines using acetylacetone (a ß-diketone) as an environmentally friendly alternative process for fines utilization. A 2k factorial experiment design was used to identify the significant extraction variables. It was found that the reaction temperature and solid to liquid ratio had significant effects on the extraction process. The extraction kinetics were studied at different temperatures and the highest iron extraction (97 %) was obtained after 48 hours at 413 K and 0.025:1 (g:mL) solid to liquid ratio for a particle size range of +106 to -150 µm. The extraction products were easily separated from the unreacted acetylacetone by flash distillation and iron(III) acetylacetonate crystals were recovered. An economic evaluation showed that selling the crystals was profitable. Alternatively, the crystals can be reduced with hydrogen to iron particles and acetylacetone (for reuse).

Jan 1, 2015

By J. S. Redpath, W. R. Dengler

"A description of the equipment used and the electrical-mechanical problems encountered in sinking a deep shaft is given. This shaft is currently being sunk to a depth of 7,115 feet. Some of the features of the sinking plant are a 6,500-hp double-drum hoist, a Blair stage hoist, special high-capacity mucking gear, a Galloway stage, high-tensile stage suspension ropes and 12-ton sinking buckets.INTRODUCTIONIN THE EARLY FALL OF 1965, a contract was let, by The International Nickel Company of Canada, Limited, to Shaft Sinkers (Canada) Limited -J. S. Redpath Limited -Joint Venture, • to sink and equip the Creighton No. 9 shaft at their Creighton Mine proper-ty in Ontario. This paper describes the electrical and mechanical equipment used by the contractor on this project, and details various problems that were en-countered.The shaft itself is circular in section and is lined with monolithic concrete. Upon completion, it will feature twin skip compartments, a cage compartment, counterweight compartment, manway and pipe compartment. The finished diameter of this opening will be 21 feet and the shaft will bottom 7,115 feet below the collar. The present depth of the shaft (April, 1968) is 5,400 feet. The opening is concrete lined as excavation takes place and the steel will be placed in the shaft upon completion of sinking. Hoisting is done on rope guides which are part of the stage suspension system."

Jan 1, 1968

By J. Budac, J. Dennett, D. Mayne, P. Nawrocki

"The Nickel/Cobalt operation in Fort Saskatchewan, Alberta has successfully used an oxidative ammonia leach process to refine a variety of feeds into high quality nickel and cobalt products for over 60 years. Fundamental changes to the refining process were made when the major feed was converted from nickel concentrate to cobalt rich mixed sulphides in the early 1990s. Since the early 1990s, the production capacity of the refinery has expanded to match increases in both mixed sulphides and other feeds. In addition to increasing the production capacity of the refinery, other changes have been required in order to improve the operability and reliability of the refinery as well as to deal with increasingly stringent safety and environmental requirements. This paper describes recent changes at the refinery including changes to the flow sheet, improvements in unit operations, incorporation of new feeds, management of byproducts, and control of impurities.INTRODUCTION The Cobalt Refinery Company (Corefco) plant in Fort Saskatchewan processes nickel-cobalt mixed sulphide intermediate produced at the lateritic nickel mine and high-pressure acid leach (HPAL) facility in Moa Bay, Cuba. Both operations are jointly owned and operated by Sherritt International and General Niquel of Cuba. The mixed sulphide, along with other feed materials, is processed at the Fort Saskatchewan refinery using a pressure ammonia leach-hydrogen reduction process to produce nickel and cobalt metal. This refinery was originally constructed in 1954 to treat nickel concentrate from Sherritt’s Lynn Lake mine in Manitoba. (Benson and Colvin, 1964; Boldt and Queneau, 1967; Forward, 1953; Forward and Mackiw, 1955; Kerfoot, 1989) From the mid-1970s until the early-1990s, the facility operated as an independent refinery, treating nickel-bearing feeds from around the world. The flowsheet was changed in 1992 to address the increased cobalt content of the feed. (Cordingley and Krentz, 2005; Kerfoot and Cordingley, 1997) The flowsheet was adapted further in 2009 to improve cobalt speciation in the leach process, which allows better cobalt-nickel separation. The 2009 iteration is shown in Figure 1. Three ammonia leach stages were used to ensure high recoveries of nickel and cobalt. Underflow solids from the final leach stage contained mainly iron oxides. One of the features of the leach process is the innovative recycling of ammonia. Ammonia vented from the leach process in tail gas and from atmospheric tanks is recovered and recycled into the refinery using water based scrubbers and a high pressure distillation process. Indeed, roughly 250 t NH3/d is recovered as distillate and recycled back into the process. Also, air enriched with ammonia which is vented from the later first stage autoclaves is recycled to the lead first stage autoclaves to maximize oxygen and ammonia utilization."

Jan 1, 2017

By Eddy Dénommé, Deni Villeneuve

"Niobec mine, a producer of pyrochlore concentrates since 1976, became a producer of ferroniobium in 1994 and achieved accreditation to the ISO 9002 standard in 1995. The goal of ISO 9002 is to ensure that the products supplied to clients regularly meet their specifications, through explicit work standards and procedures throughout the production process, from deposit appraisal to ferroniobium production.A key element of ISO 9002 implementation at Niobec consists of the quality control procedures applied to the raw materials: the ore fed to the mill and the pyrochlore concentrate fed to the reduction plant. These controls extend from exploration, deposit appraisal, mine planning and reserves estimation, mining, mineral processing and, finally, ferroniobium production. The implementation of ISO 9002 has allowed more efficient control of the quality of the final product sold to clients. It requires interactive team work, the role of the geologist being to relate all information pertaining to raw material and product quality to the geological framework of the deposits."

Jan 1, 1997

By L. Bratek, K. Jaworek, M. Czaplicka

Methods for arsenic compound removal from aqueous solutions include processes such as: coagulation, adsorption, membrane techniques, electrochemical and biotechnology techniques. Advanced oxidation using both UV radiation and strong oxidizing agents such as ozone and hydrogen peroxide may also decompose these compounds. It is known that effluents from metallurgical processes contain inorganic arsenic compounds in addition to the organic compounds such as: dimethylarsinic acid and phenylarsonic acid. This paper presents the conditions that lead to the formation of deposits containing mainly arsenic, such as pH, the wavelength of the radiation and the type of oxidant, for this type of effluent.

Jan 1, 2014

By C-D. Johansson, B. Ögren, B. M. Ludvigsson, K-Å. Johansson, R. Lindh, G. Berg, M. Maliarik

This paper presents the High Current Density (HCD) Silver Electrorefining Process. A 25-year history of development of the silver electrorefining process as well as associated equipment is given. The process is simple and robust, but at the same time highly automated. With low operating costs and man power requirement it allows consistent production of 99.99 % quality cathode silver. The process ensures that no toxic gases are formed in the working environment. Silver Electrorefining is a heart of a Silver Refinery plant covering the complete range of processes from casting of silver Doré anodes to casting of the bars of refined silver or/and silver granulation. The process has been successfully applied at 11 installations world-wide with plant capacities ranging from 30 to 1500 tpa.

Jan 1, 2014

By Ron Light, Doug Applett

"HistoryThe Nanisivik mine began operation in October 1976 as the world's most northerly metal mine and the first permanent industrial project in the Canadian High Arctic. Located 700 km north of the Arctic Circle on Baffin Island's Strathcona Sound, exploration by Texasgulf Inc. between 1957 and 1970 had outlined the ore deposit. In 1974, Nanisivik Mines Ltd. was formed with Mineral Resources International, the Government of Canada, Metallgesellschaft and Billiton being shareholders, and Strathcona Mineral Services Ltd. providing project management. In 1996, Breakwater Resources purchased the mine from Alberta Energy Corporation Limited which had recently acquired the assets of then owners Conwest Exploration Ltd.Ore DepositThe main ore deposit is very flat, approximately 80 m in width and varying in thickness from 3 m to 16 m. The length of the deposit is approximately 3000 m with satellite zones located on the perimeter of the main zone. The economic mineralization is sphalerite with minor galena and silver. The sphalerite and galena are coarse grained and associated with pyrite as the main gangue component with minor inclusions pf dolomite and calcite within the deposit. The deposit being hosted in a permafi·ost environment creates a number of challenges. Dry drilling is employed in room and pillar production drilling. The permafrost aids in the stability of both the pillars and the back."

Jan 1, 2000