Search Documents

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

By André van Wageningen

Since the beginning of this century Boliden Mineral and Atlas Copco have worked together in stages on improving the accuracy and quality of drilling. Navigation of the drill rigs with IREDES has been in use in the Boliden mines for several years. Recently the capability of the system has extended with map navigation to more accurately follow the ore in cut&fill mines. The system allows for changes on the individual round level to follow the ore without changing the whole design for the heading. Those changes are done in a CAD-system and remove the need for face markings and will allow for even better accuracy in both height and wall position. All the information between the CAD-system and the drill rigs is exchanged using the IREDES standard. This paper describes the workflow and the use of the IREDES standard.

Oct 1, 2009

By J. S. Stickling, P. J. Whittaker, N. O. Lotter

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from mineral processing and mineral science.More recently, process mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (quantitative evaluation of materials by scanning electron microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX/WDX capabilities and an XRD, the development of process mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002

By T. G. Joseph, K. Barron

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an “apparent friction” concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of triaxial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock. This strain-softening relationship is then applied to coal. Having determined the post-failure stress-strain curve for coal specimens, this information can then be used in a finite element program, such as Phase 2, to examine the post-failure characteristics of coal pillars. Using example data, the strength of coal pillars of different width/height ratios are estimated and compared with well-known empirical pillar size-strength relationships. In addition, the post-failure stress-strain behaviour of a coal pillar is compared with an empirical relationship reported in the literature.

Jan 1, 2003

By S. Haggarty

"Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Milling capacity is 3,400 SDT /Day with an average feed grade of 0.080 Oz Au/Ton. Gold processing involves three stage grinding including tertiary pebble milling, two stage cyanide leaching and filtering and Merrill-Crowe zinc precipitation.A summary of process improvements required to increase milling capacity above the initial design tonnage of 2, 700 SDT /Day are described -Installation of a 42"" x 65"" Allis Chalmers Gyratory crusher replacing a 42"" x 48"" Traylor jaw crusher.Installation of polyurethane screen panels replacing woven wire cloths on an 8' x 20 ft triple deck screen.Installation of a hopper clarifier to reduce filtrate turbidity.Automated control of solution balancing and effluent treatment circuits.INTRODUCTIONThis paper describes mining and milling practices at the Nickel Plate Mine and details post start-up process modifications which were required to attain design tonnage.Wholly owned by Corona Corporation, the Nickel Plate Mine is an open pit, gold mining operation located near Hedley, 50 km west of Penticton, in Southern British Columbia.Mining capacity from the open pit is approximately 32,000 TPD with an average waste/ore ratio of 8.4:1.Milling capacity is 3,400 SOT/Day, above initial design tonnage of 2,700 SOT/Day. Feed grade averages 0.08 Oz Au per ton yielding 85,000 troy ounces of gold per year."

Jan 1, 1991

By D. E. Gorse, R. G. Anderson

"Indusmin's history dates back to 1937 when they developed the Blue Mountain Nepheline Syenite deposit at Nephton, Ontario, and began supplying material for the glass, fiberglass, paint, ceramics and rubber industries.Since then, as a subsidiary of Falconbridge Nickel Mines, Indusmin has expanded the Nephton operation, diversified into the aggregate quarries for the construction industries, with operations at Acton and Halton, Ontario, established silica plants at St. Canut, Quebec and Midland, Ontario, to supply the glass, carbide, ceramics, cleanser and concrete products industries, and the purchase of a foundry, Fahramet Limited, Orillia, Ontario, supplying steel and alloy castings to the mining, construction cement and petrochemical industries.Indusmin also has a Technical Resource Centre and Head Office facilities in Toronto.As this paper deals with Indusmin's experience with dust abatement, and although dust control is a concern at the Nephton, St. Canut and Orillia plants, we will be confining this paper to the experience gained at the Badgeley Quarry and Midland plant of the Ontario Silica Operation."

Jan 1, 1980

By R. W. Nice

"The Similkameen Mining Company property is situated about 9 1/2 miles south and west of Princeton B.C. Owned and operated by Newmont Mining Corporation, mining is presently taking place in the Ingerbelle pit. At 15,000 tpd of 0.50% Cu ore the Ingerbelle pit is sufficient for about 8 years. Another 8 years ore supply is available from the old Granby workings of the Copper Mountain property which operated from 1927 to 1957.The pit operations commenced in late 1970 with the concentrator starting in March 1972. Designed and built by Bechtel Corporation under the supervision of Newmont the concentrator's design was based on single-stage crushing and single-stage modified autogenous grinding. The modification was installation of a crusher to crush the critical size build-up. The description of the operation follows.CRUSHERThe primary crusher is an open pocket Allis-Chalmers. 54"" x 74"" gyratory. The basic closed side setting is 8"". The crusher is fed from one side with 100 ton Electra-haul trucks. The crusher pocket discharges to a 96"" wide conveyor belt, then to a 48"" conveyor system including a stacker belt. The crushed product is piled on a stockpile with a capacity of about 30,000 live tons. This stockpile feeds the concentrator."

Jan 1, 1975

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

By P. Trudel, É. Cabot, L. Cabot

"A modular gold processing unit (MGPU) was designed, installed and operated over an eight-month period by RSW-Béroma at the Granada mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up, as well as exploitation results, including productivity and profitability curves, are given for a small-scale mining operation in comparison with larger ones. IntroductionSmall-scale mining (SSM) is a widespread activity in Africa, Mexico, Central America and South America, where numerous small mineral deposits are exploited manually or by semimechanized methods. On the other hand, SSM is almost absent in Canada, where the mining industry traditionally exploits large deposits, using concentration plants with capacities of many thousands of tonnes per day. However, many small gold (and other metallic or industrial mineral) deposits are known in Canada. Their reserves are too small to justify the cost related to the construction of a standard mill and, if they are remote from a custom milling facility, they remain unexploited. With this in mind, RSW-Béroma has developed the modular gold processing unit (MGPU) that allows the profitable exploitation of small mineral deposits. The MGPU is the perfect tool for SSM and its main advantages are a much lower capital cost than a standard mill and its portability, which makes it easy to transport and reinstall on another site, once the exploitation of a small deposit is terminated. The denomination MGPU will be used hereafter in the text as it was primarily designed for gold deposits, although it must be kept in mind that this portable plant can be adapted to other mineral substances."

Jan 1, 2003

By Glen A. White

The level of impact and mitigating measures that are forecast in an environmental assessment (EA) for a new, or significantly modified, metallurgical processing facility or mine are taking on increasing importance during the subsequent life of the facility. The basic premise is that one is authorized to operate within the envelope defined by the approved EA. Operations inevitably change as they develop and mature, and at some point, one is faced with the prospect of re-doing the original EA work. This can lead to significant development delays. Cameco Corporation (Cameco) has played a major role in developing the northern Saskatchewan uranium mining industry over the past decade. Through the EA process, the company has developed ideas on what works well in generating approvals that give the operator some future flexibility. Early introduction of concepts for potentially different mining and processing methods, as well as contingency plans if things do not work out exactly as predicted in the original EA, can make subsequent regulatory approval for change a more efficient process. One must also preserve the principles of open consultation upon which the EA process was originally based. As such, involvement and support from local communities and other stakeholders is required to ensure the long-term success of the EA process.

May 1, 2004

By V. I. Lakshmanan, D. A. Mackie

"1. INTRODUCTIONIn the past two decades, low-grade gold and silver ore bodies in the United States have been exploited by heap leaching, primarily with sodium cyanide solutions. This method has proven to be a viable alternative to conventional milling due to its low capital and operating costs. Successes have been made, particularly in Nevada, where ores are well oxidized and the climate is conducive to this method. in recent years, heap leaching has been tried in northern latitudes with some success, however, in using this method, operators face more severe limitations than do their neighbours to the south.This paper evaluates the limitations of heap leaching with particular emphasis on northern climates and introduces an alternative method to recover precious metal values in a continuous vat. This proprietory technology, known as the Mackie Vat Leaching Jig, shows promise, with improved gold recovery and potential to operate in cold climates.2. WHAT ARE THE LIMITATIONS TO HEAP LEACHING?Heap leaching of non-refractory ores is subject to the following limitations:1. Minimum amount of free gold and nuggets in the ore.?. Minerology of the ore--accessibility of gold to lixiviant.3. Minimum particle size and size distribution of crushed product to allow percolation of lixiviant through the heap.4. Minimum amount of clays or clay-like slimes that can cause coating of ore particles and channelling of lixiviant.5. Minimum strength of ore particles or agglomerations to allow economic height of heaps to be built.6. Amount and suitability of real estate.7. Amount and type of precipitation.8. Ambient temperatures.9. Possible poorer lixiviant diffusion.10. Possible lower oxygen content in dissolved cyanide solution with higher heaps, particularly with ice and snow cover."

Jan 1, 1989

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004

By D. Stone

"The Beal Mountain mine near Anaconda, Montana, is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of approximately 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges."

Jan 1, 2002

By The Staff

FOR forty years cyanide men have been intensively engaged on the treatment of sulpho-telluride ores. So far as we know, the processes used today were-with the important exception of the concentration plus high-lime process at the Victor mill (1915)-in use, or had been tried, in the earl y years of the century. Roasting, bromocyanide, ordinary cyanide, table and vanner concentration, floating and treating the concentrate, roasting con-centrates prior to treatment, etc., all were used at Kalgoorlie in 1904 or earlier. Flotation, followed by shipment of the concentrate to the Golden Cycle mill, was the practice at the Vindicator mine, Cripple Creek, for some years prior to 1917. Similar practice was employed in the Portland Independence mill at Victor, Colorado, and was lacer superseded by the table concentration, high-lime cyanide treatment of rails of the older Portland Victor mill. During all this time, an immense amount of research was being clone on these ores by the staffs of numberless companies. Conclusions were drawn and mills built. But if the results of one per cent of this research were ever published in sufficient detail for intelligent use by others, the Lake Shore staff has been unable to discover them, or does not recall having clone so. Government laboratories-as for instance chose of the Mines Branch, Ottawa, in or about 1927-have touched upon certain methods in their publications, but they simply have not had the time to finish the job. The paper by W. E. Johnston, Tellurides-Problem or Alibi? (E. & M.]., Aug., 1933), aroused wide interest and comment. It published conclusions, some right and some wrong, and gave the evidence adduced by the author i:n support thereof. Conclusions published without supporting evidence are to most of us worse than no conclusions at all. We suggest chat, if even one-tenth of the operators had published full, detailed results of their laboratory work, ad vance in the treatment of sulpho-telluride ores would have been very much accelerated. Therefore, we venture to inflict upon the Institute a compendium of the results of laboratory work performed during the past few years at the Lake Shore mill. It is really a summary of the more interesting results to date, prepared by the mill staff for their own use and benefit. But we hope chat the discussion under any heading is so detailed chat it will be intelligible to anyone interested in that phase of the subject.

Jan 1, 1936

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

By M. Tarvainen

"Lately, the development work in closed circuit grinding has mainly been focused on mills and on different types of instrumentation, mathematical models and automation in spite of the fact that the poor efficiency of the classifier is well known. It has also been proven by several investigations that by improving the sharpness of classifier separation, remarkable technical and economical advantages can be achieved. Some attempts to improve the performance of the most common classifier, hydrocyclone, have been made, among them injection of wash water above the spigot cyclone and retreatment of either or both of the products of the primary classifier. No method has been successful enough to achieve general adoption in the industry. The purpose of this paper is to introduce some industrial results achieved by two-stage classification where the coarse product of the turbulent-flow classifier, hydrocyclone, is cleaned in a laminar-flow cone classifier.The main target of the adoption of the two-stage classification circuit it naturally to improve the sharpness of size separation. This again leads to the following advantages in the grinding process:- lower circulating load and increased capacity- lower energy consumptionnarrower size distribution in the fine product- less overgrinding and less slimes- reduced specific surface areaThese improvements, no doubt, reflect on the subsequent concentrating process in the following aspects:the rate of flotation is improved, less reagents and energy is neededthe recovery and grade of valuable minerals in concentrates is improved- savings in dewatering can be expected- less fines in tailings improve the conditions for water recirculation."

Jan 1, 1980

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By D. P. Tripathy

A supply chain encompasses all the activities associated with the flow and transformation of goods from the raw materials stage(extraction), through to the end user. Supply chain management (SCM) is the integration of these activities through improved supply chain relationship, to achieve a sustainable competitive advantage and it rests on its ability to provide the right goods and services when and where needed. The supply chain is the vital component of any company?s value chain which links the operating processes to its supplier and customer. The globalization of business promises to offer new and unique challenges for the supply chain competencies of most firms. Challenges will also increase in the environmental aspects of supply chain often referred to as ?Green Issues?. The supply chain of mining industry comprises of the flow of material and information from the mine site, to processing and loading for transport, to the customer. However, due to recent changing environmental requirements affecting mining and mineral processing operations, increasing attention is given to developing environmental management (EM) strategies for the mineral supply chain. This paper focuses on: ? Environmental factors leading to the development of an extended environmental supply chain, ? Additional challenges presented by the extension, ? Performance measures appropriate for the extended supply chain, ? Developing a general procedure towards achieving and maintaining the green supply chain.

May 1, 2006

PRESENTATION PURPOSE ? Provide an overview of BC?s Environmental Assessment Actand environmental assessment process ? Identify key issues influencing environmental assessments in BC ENVIRONMENTAL ASSESSMENT ACT ? Major project proposals require an EA before a project can proceed ? Considers potential effects of proposed projects and ways to minimize or avoid adverse effects Minister of Environment and the Minister designated as responsible for project category decide whether or not to certify a project or order further assessment

May 1, 2006

By N. I. Basuki, E. T. C. Spooner

"Abstract - More than 2800 published fluid inclusion data (primary inclusions) from eighteen typical Mississippi Valley-type (MVT) Zn-Pb deposits and districts were examined to study possible relationships between MVT fluid properties and metal tonnages and ore grades. The mean Th and salinity values for fifteen MVT deposits and districts are 122°C ± 21°C and 20.7 ± 2.6 wt% CaCl2 equivalent, respectively. In general, temperatures increase from pre-ore to ore stages, and salinities decrease from ore to post-ore stages. From post-ore to late calcite stages, salinity and temperature decrease with various trends within specific districts.Several conclusions are drawn: first, results show that Hanor’s (1996) salinity threshold for metalrich basinal fluids applies to typical MVT ore fluids (~16 wt% CaCl2 equivalent). Second, the lower limit of mean Th values of measured MVT deposits and districts (n = 15) of ~75°C is similar to Hanor’s (1996) observed temperature threshold for metal-rich basinal brines of ~60°C (n = 224). Third, there is no statistically significant relationship between fluid inclusion homogenization temperatures (Th) and metal tonnages or ore grades. Fourth, there seems to be a tendency for large tonnage districts/deposits to be associated with mean fluid salinities that are relatively low (~16 to 21 wt% CaCl2 equivalent) within the overall range of salinity means (~16 to 26 wt% CaCl2 equivalent). There is also a correlation between higher ore grades and higher salinities. Finally, comparison with other sedimentary rock-hosted Zn-Pb deposit types shows a trend of salinity decrease and temperature increase from MVT, sandstone-hosted and diapir-related Pb-Zn deposits, to vein-type and Irishtype Pb-Zn deposits, and then to sedex deposits. However, more data are needed for sedex deposits. The salinity threshold for significant Zn-Pb transport decreases to =~10 wt% CaCl2 equivalent at ~250°C. This study suggests that fluid inclusion analysis during exploration may be useful in assessing ore-forming potential (threshold salinity) and possible ore grades (salinity)."

Jan 1, 2002