Search Documents

King Island is situated at the western approach of Bass Strait and approximately mid way between Victoria and Tasmania. The scheelite orebodies lie within the south east of the island. Ore bearing horizons from 10 m to 40 m thick occur in south and east dipping stratiform deposits. The orebodies occur in skarn formed by contact metasomatic replacement of carbonate rocks by granite intrusives. The scheelite is deposited as fine disseminated grains in and along the margins of andradite garnets in the skarn. King Island Scheelite operates two under- ground mines from which 350 000 tonnes per year are obtained. The Dolphin mine produces almost two-thirds of the total. See Figure 1. The Dolphin orebody lies beneath the sea and an area of reclamation. The orebody is inter- sected by zones of major dislocation. A chequerboard post pillar cut and fill stoping system has been chosen to provide the necessary support to the hanging wall. Because the stability of the pillars is critical to the economic welfare of the mine, considerable attention is given to the reduction of overbreak.

Jan 1, 1977

By P J. A Lever

This paper presents details of CRC MiningÆs work with waterjet assisted blasthole drilling. The objective of this work was to investigate techniques that reduce the cost and increase the productivity of blasthole drilling. The focus is on a technology that uses a high pressure waterjet to assist the conventional rotary rock cutting action of a tricone drill bit. The potential benefits of this technique are increased productivity, reduced drill bit wear and reduced hole deviation and hence improved quality of drilling. This paper describes the results of a laboratory based experimental program comparing conventional tri-cone drilling performance to the proposed waterjet assisted approach. Additionally, work has been completed looking at the more practical issues around the collection and sampling of drill cuttings and water recovery (recycling) when drilling with a waterjet. These studies have demonstrated that waterjet assisted drilling can significantly increase the rate of penetration over conventional rotary drilling. For the best-case experimental result, the relative improvement was over 40 per cent. More importantly, it is a starting point for examining alternative uses of the additional drill productivity obtained from waterjet assisted drilling. For example, increased drill productivity could be used to improve rock fragmentation by drilling a tighter blasthole pattern in the same time period. an existing drill fleet, then the drill fleet size could be reduced, or improved rock fragmentation could be achieved by drilling a tighter blasthole pattern within the same time period.

Jan 1, 2004

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

By Viney K. G, Molinia A. B

The Hellyer Pb-Zn-Ag orebody in western Tasmania was discovered in 1983, and mine production at a rate of 250 000 tonnes/yr commenced in 1987. Expansion to 1 million/yr will be completed by early 1989. Exploratory development to gain access to the orebody, to provide a 20 000 tonne bulk sample for pilot plant work and to confirm mining conditions and orebody continuity was undertaken using conventional drill and blast techniques and large diesel trackless equipment. A ventilation shaft was raisebored. Development in this phase totalled 2 815 m and provided a sound basis for rapid expansion of the mine.

Jan 1, 1988

Registrations for the Congress were 393 asdelegates and 200 as accompanying persons.The breakdown of registrations by countries isshown in Table 1.

Jan 1, 1986

Aspects and anomalies in the present Standard Specifications for Blended Cements which may have operated in Australia against the development of the greater use of Slag Blended Cements are noted. Estimates of slag and ash usage in Australia are given and the need for further research with local materials stressed.

Jan 1, 1979

It is suggested that if adequate knowledge is available about classifiers in closed grinding circuits, these units may be used as on-stream size analysers when equipped with suitable sensing devices. Research work which is at present in progress to enable a hydrocyclone to be used for this purpose is discussed.

Jan 1, 1967

By Aspinall T. O

This paper discusses the identification and assessment of risk for mining developments particularly for open pit mining. A distinction between sensitivity studies and risk analysis is developed, demonstrating the importance of geological and mining engineering judgement -as applied by experienced practitioners to the analysis and assessment of risk in such projects. Technical and financial risk analysis are discussed under: ò mineral resources and ore reserves; ò mining and processing methods; ò project construction; ò financing; and ò costs and commodity pricing predictions.

Jan 1, 1994

By M Elias

Management of risk has always been an integral part of successfully executing engineering and construction projects although formal recognition of the discipline of risk management is a relatively recent development. This paper describes the establishment and application of a proprietary business risk management framework for FluorÆs global engineering and construction business.

Jan 1, 2003

By B Madeja-Struminska

The method of evaluation of the approximate temperature of arising spontaneous fire centre and time of coal self-ignition is presented in this paper. The method uses BystronÆs (1997) model of coal self-heating and measurement of carbon monoxide concentration in the mine air outside the fire centre. Knowledge of the spontaneous fire centre temperature and time of fire beginning allows for more accurate analysis of the fire hazard in the coal mine and allows for adequate time to undertake special fire prevention actions. The method is illustrated by an example from Polish mining practice.

Jan 1, 2005

It is a facet of modern-day life that change, even of a revolu- tionary nature, normally passes without comment. People have become so conditioned to continuous improve- ments in every aspect of their lives that they would be surprised only if there were to be no change. This paper seeks to demonstrate the extent of technical change, and to indicate the need for a fuller advantage to be taken of the technologies available, or potentially available, to the profes- sion. It contends that the mineral industry has been particularly slow to embrace technical change, and has good reason to con- sider an improved attitude for both prosperity and survival.

Jan 1, 1988

Improvements in mechanisation should not be considered independently of safety and of environmental hazards. The need to keep gas contents within statutory limits may make the time needed to partially drain a gassy seam the effective control on face development times. Dust levels may provide an effective control on coal extraction rates on any one face. The combination of gas and dust on high output longwall faces may make it necessary for each one to be treated as a separate mine in terms of ventilation, and the faceworkers may need special protection. Mechanisation and safety can be mutually beneficial when mechanisation combined with systematic safety assessment reduces accidents, and when a thorough study of how to reduce accidents and health risks indicates the best method to improve mechanisation.

Jan 1, 1988

An extensive railway construction prog- ram in the People's Republic of China has required the excavation of many tunnels in difficult ground, particularly in mountainous regions. Conclusions drawn from case histories permit guidelines to be formulated as to the optimum location of tunnel alignments in faulted and folded terrains, and also in karst regions. Geological factors adversely affecting durability of tunnel linings can be minimised by adoption of appropriate construc- tion practices.

Jan 1, 1987

By J Borthwick, M Yusi, M Douge

Feasibility studies form a vital and significant component of the project delivery cycle. They are at the heart of the valuation process. This paper focuses on variables which can affect a project and how these are assessed as part of the decision-making process through feasibility studies. Test work and site selection needs; the degree of engineering required to meet the study requirements and the quality of owner project information are discussed. Also, local factors including permitting needs, social, environmental and government relations are considered. Engineering and site factors are crucial in the estimating process. The interaction of detailed engineering, engineering assumptions and estimating methodologies are therefore examined. The ownerÆs perspective is considered along with risk analysis, which is fundamental in project feasibility study activities. The impact of this is also discussed.

Jan 1, 2009

By S Morrell, D Clark

æMine to MillÆ improvement involves optimising the chain of rock breakage processes from the in situ rock in the mine to the output of the concentrator. A growing number of paper studies and case histories from metalliferous mines (AusIMM, 1998; JKMRC, 1998; Clark and Scott, 2002) demonstrate that generating more breakage in the pit and the primary crusher can lead to benefits to milling that result in significant improvements to the economic performance of a mining project. However, unless the ævalueÆ of doing this (benefit over cost?) can be appropriately quantified, the approach cannot be effectively managed and the increases in blasting and monitoring costs cannot be justified.Mining operations have traditionally been organised into the separate departments of geology, mining and processing based on the specialist skills required and the different professional disciplines involved. Process optimisation across these boundaries has commonly been frustrated by management requirements to minimise the costs incurred by each department without adequate reference to the ævalueÆ being created. Companies have tended to discard positions that provide a technical over-view of the value chain, reducing the number of people with the opportunity to influence practices across these process boundaries.This paper discusses these issues and identifies measures required to quantify and manage the ævalueÆ provided by æMine to MillÆ improvement generated by the intense blasting of ore.

Jan 1, 2002

By Burgess J

Present practice of lead-zinc flotation at North Broken Hill Limited is described and factors influencing plant objectives and performance discussed. Mineralogical examination of final flot- ation products showed mineral liberation to be 94T complete and size by size metal recovery tables indicated a need for finer grinding to improve lead and silver recovery, but coarser grinding to improve zinc recovery. A steady grinding circuit, at constant ball mill power and cyclone overflow pulp density, is found desirable for satisfactory flotation circuit operation because instabil- ity in the grinding circuit inevitably leads to flotation instability and as a consequence less than optimal flotation operation. Remov- al of the variable lead flotation middling product from the grinding circuit decreased grinding instability.

Jan 1, 1978

By Hamilton LH, Campbell PB

Since fundamental research in applied coal petrography is carried out mostly on polished surfaces, backscattered electron microscopy is most applicable for studying coal in the SEM. By employing this technique coal macerals can be easily identified , and information on the relations between maceral groups, mineral matter and trace elements are highlighted by grey level contrasts. This type of information is valuable in coal technology and cannot by normally revealed by the light microscopy (e.g. the distribution of inherent mineral matter).

Jan 1, 1989

The use of ammonium nitrate/fuel oil explosives is.now well established in most open cut mining operations. Its use. is extending to underground mining. This has been due in a large measure to improvements in the nature of the ammonium nitrate made available from various sources. The addition of surface active agents and water in controlled amounts to the fuel oil has been found to increase the sensitivity of the ANJFO mixture with consequent better explosive properties. It is considered that the surface active agent increases the bond between the ammonium nitrate and fuel oil giving a more, intimate physical and chemical mixing of the oxidising and reducing agent. This results in increased sensitivity and a faster rate of reaction. The increase in sensitivity has been accomplished without any diminution of safety. Tests which demonstrate the safety of this type of explosive are given in the appenuix.

Jan 1, 1964

By Waldram JT

The Kelsey Centrifugal Jig incorpo- rates the principles of operation of a conventional mineral jig, at the same time utilising high centrifugal forces to extend concentration to very fine heavy minerals. The main operating variables which are adjusted to control processing of different types of material are centrifugal force, ragging material and size distribution. Pilot plant trials have been under- taken to examine concentration of a mineral sand in which the heavy mineral particles occur mainly in the minus 0.075 plus 0.032 mm size range. Stage recoveries of greater than 90% were achieved at concentration factors of up to 2, although lower recoveries were obtained with higher concentration factors. A final concentrate containing 65% heavy minerals was obtained.

Jan 1, 1986

Total quality control in tandem with Japanese style management largely accounts for the high product quality and international competitiveness of growing manufactured exports from Japan. Japanese management is often identified with life-time employment, promotion by seniority, company-based unionism, the process of obtaining the sanction of executives to a plan by circulating the draft prepared by a person in charge of a particular matter, internal consultation, consen- sus-based decision-making, etc., all of which are just formal manifestat- ions of the underlying current of the spirit of cooperation that translates itself into "management through labor- management cooperation".

Jan 1, 1982