Search Documents

By B B. Beamish, M S. Kizil

The processes that take place during the development of a heating are difficult to visualise. Bulk coal self-heating tests at The University of Queensland (UQ) using a two-metre column are providing graphic evidence of the stages that occur during a heating. Data obtained from these tests, both temperature and corresponding off-gas evolution can be transformed into what is effectively a video-replay of the heating event. This is achieved by loading both sets of data into a newly developed animation package called Hotspot. The resulting animation is ideal for spontaneous combustion training purposes as the viewer can readily identify the different hot spot stages and corresponding off-gas signatures. Colour coding of the coal temperature, as the hot spot forms, highlights its location in the coal pile and shows its ability to migrate upwind. An added benefit of the package is that once a mine has been tested in the UQ two-metre column, there is a permanent record of that particular coals performance for mine personnel to view.

Jan 1, 2005

By Davies S. G, Jayaweera A

The oxidation of nickel sulphide and copper sulphide concentrates, and coal, has been studied under non-ignition and ignition conditions using Differential Thermal Analysis (DTA) and Thermogravimetry (TG). The non-ignition reaction was favoured by slow heating rates < 10°C min-1), low masses < 10 mg) and an air atmosphere. Under these conditions, the typical stepwise oxidations of the various sulphide minerals present in the concentrate were observed as resolved exothermic peaks in the DTA curves and weight losses in the TG curves. Above a heating rate of 10°C min-1 , sample masses in excess of 10 mg and an oxygen atmosphere, an ignition reaction was induced, as indicated by a major high energy exotherm in the DTA curve and a major rapid weight loss in the TG curve. The ignition temperatures of the minerals under ignition conditions, found for 15 mg samples heated at 20°C min-1, were 434°C for the nickel sulphide concentrate, 372°C for the copper sulphide concentrate, and 230°C for the coal. By plotting a curve for mass against ignition temperature at constant heating rate and extrapolationto zero mass, a value of 470°C was obtained for the mass independent ignition temperature of the nickel sulphide concentrate. Ignition temperatures and extents of reaction at various temperatures were obtained using the TG technique in a novel manner which produced heating rates of 4500°C min-1. Under ignition conditions, the oxidations approximate to flash smelting conditions.

Jan 1, 1985

The highland region of Papua-New Guinea is relatively rugged terrain where stream gradients are steep. In areas where porphyry copper deposits outcrop the streams commonly expose primary sulphide mineralization in unoxidized rocks. Stream sediment geochemistry combined with float examination and broad geological mapping proved to be an effective tool for detection of outcropping bodies of mineralization. After discovery, detailed stream sediment sampling, soil sampling and rock chip sampling, together with detailed geological mapping proved adequate to delineate drilling targets. Reconnaissance stream sediment sample density was dictated by geology and access and a density of one sample per 25 Km2, or less, was desirable to ensure a high degree of confidence in the programme. Research indicated that the base metals occur in sulphide form in stream sediment and that the -80 mesh size fraction gave the most reliable results. The evaluation of results from any one area relied on the interpretation of the local geology. Basic histogram methods for determining background and threshold values for metals in stream sediments were

Jan 1, 1973

This paper contends that optimisation of energy resources through active control and predictive simulation modelling is possible, and that such monitoring leads to large savings in the electricity costs of hot mines (where refrigeration has to be employed). In addition, active monitoring and control can positively affect the establishment of a safe, healthy and productive working environment. In the entire optimisation process certain guidelines were set to ensure that the requirements of the Mine Health and Safety Act were met (South Africa). Varying the quantity of air supplied underground by means of variable speed drive (VSD) fans is one of the crucial factors in the interactive approach towards the optimisation of ventilation, as is refrigeration and the pumping requirements associated with refrigeration. This article highlights the interaction between the amount of air supplied and the effect it has on refrigeration requirements underground. This article also considers the effect that this would have on contaminant control. Various tools are available for ventilation and cooling design for mining. A lot of these tools are based on the assumption of steady state conditions and do not take into account instantaneous changes in conditions, day-to-day, or hour-to-hour (such as for temperature and contaminants). They also do not take into account the optimisation of energy resources related to the creation of the acceptable underground conditions. With these tools worst-case and best-case scenarios are identified, and strategic decisions are made accordingly. Currently, the amount of the fresh air, the velocity of the air, and its general temperature in the mine are only changed when one production phase changes into another (or when unacceptable conditions occur as a result of poor design or neglect). This means that during a specific production phase (which can last for several months), there can be an oversupply, or undersupply, of energy resources, which will obviously affect the concentration levels of the various contaminants (through under or oversupply of air).

Jan 1, 2005

By S Sabanov

Supplementary sampling of particulate mass concentration, the number concentration and the average particle diameter of nanoparticles using a TSI Dust-Trak DRX Aerosol Monitor, Naneos Partector 2 has been conducted. The aim of this study was to evaluate suitability of the instrument for long-term monitoring of diesel particulate matter (DPM) at conditions of polymetallic mines. Sampling was conducted in an area of the active ore heading, requiring the use of a diesel-powered face haul-age loader R1700 and a mine truck Caterpillar AD-45. The sampling was done for 126 minutes at a distance of 30 metres from the mine face. Results of this field work can be used to expand the sampling program to other mines. Expected outcomes of this study are to develop costeffective DPM control strategies, improve mine ventilation, and protect mineworkers’ health.

Oct 12, 2022

By D Cai, E Baafi

Various enabling technologies and systems have recently been introduced in the mining industry. Such systems include miner-bolters with concurrent cutting and bolting, employment of two shuttle cars, adoption of self drilling bolts and utilisation of continuous haulage or monorail systems. The paper discusses how Flexsim discrete event simulation models were used to assess how these proposed mining systems can best be used to achieve and sustain high roadway development rates of 10 m per operating hour for 20 h/day.

Sep 26, 2011

By B P. Banerjee, D Patra, S Raval

Roof bolts are an essential component of roof support systems in underground mines. They are used to provide structural support to the roof of the mine and prevent it from collapsing. Therefore, it is imperative to perform regular assessments of these roof bolts to avert any hazards. Manual investigations of roof bolts are done by surveyors in underground mines, which is extremely timeconsuming and challenging due to the low-light conditions in underground mines accompanied by stringent mine access rules. To this end, automated recognition of roof bolts in 3D point cloud data obtained through laser scanning in underground mines serves as a potential solution to aid roof bolt monitoring. With the continuous advancements in laser scanning-based 3D data acquisition systems, the feasibility of making such surface estimations from 3D point cloud data has increased severalfold.

Sep 1, 2024

By West RF, Pooley RH

An underground mine, a treatment plant and supporting facilities have been constructed at Lebong Tandai in Sumatra, Indonesia by PT Lusang Mining. Throughput is initially 50,000 tonnes per annum of ore with an inbuilt capability to expand to 100,000 tonnes per annum. Construction proceeded in parallel with design work on a tightly controlled critical path schedule. The very remote location of the mine, the difficult access and the fact that equipment was imported from many parts of the world presented a challenging project management problem. The transport system, which involves road, river and rail and support facilities on site had to be brought into full operation prior to the arrival of major equipment. Mine development involved the reopening of the old access drives and workings, refurbishing two shafts and the haulage system together with redevelopment of old stoping areas and the opening of new stoping areas. Ore production is now from three main areas using shrink and underhand stoping methods. Ore breaking and drive development is with conventional airleg mounted rockdrills and ANFO explosives. Exploration to locate and develop new reserves to replace ore mined is an ongoing activity.

Jan 1, 1986

By N Maistry, A Singh

It is estimated that in less than a decade, high-grade iron ore reserves in South Africa will be depleted, leaving only low-grade ores with a dominant lithology of banded iron formation (BIF) hematite. BIF is a complex ore reserve as it is typically liberated below 1 mm, resulting in high energy costs. However, due to its abundance, its beneficiation potential should be evaluated to maximise recovery at an acceptable product grade. To develop a beneficiation program for BIF hematite, the first step is to determine the effect of two laboratory crushing techniques on mineralogical characteristics, specifically liberation and shape. For this study, the cone crusher and high pressure grinding rolls (HPGR) were used. The Electron MicroProbe Analysis (EMPA) and Mineral Liberation Analyser (MLA) were used to compare the mineralogical characteristics. The liberation characteristics for hematite are similar for both crushing techniques; however, HPGR preferentially liberates quartz. HPGR achieved 8– 12 per cent additional quartz liberation in the greater than 80 per cent and 100 per cent liberation classes respectively and specifically in +75 μm size range. Improved quartz liberation is associated with lower energy requirements for downstream milling and improved separation efficiencies for beneficiation units that operate in this size range. Both samples displayed similar shape characteristics; most particles were elongated smooth and the rest were elongated angular. Good hematite liberation is expected at grinds of 212 μm to 150 μm. Further consideration should be given to throughputs, energy efficiency and downstream equipment selection prior to selecting a crushing technique.

Sep 18, 2023

The application of cheap robust microprocessor based units to achieve monitoring and control in an underground mining environment is described. The functional layout of the programmable controller and the methods of multiplexing and processing information from local and remote sources are examined as are features for refrigeration plant control.High noise immunity communication to a remote micro computer uses existing telephone lines and enables display and print of essential data. The development of this system then leads to applications in monitoring compressed air, ore transport and underground fires.In conclusion, the problems of data presentation to different levels of management and the future philosophy of a central multi-reporting system are discussed.

Jan 1, 1985

By G R. Dickens, N H. S Oliver

The genesis of giant hematite ore deposits in northwest Australia remains a contentious topic in part because key evidence supporting a unifying genetic model has not been found at all deposits. In particular, several papers have proposed that carbonate replacement of silica layers in banded iron formation (BIF) by basinal brines is a requisite first step toward ore formation. This initial hypogene stage is inferred primarily from the presence of silica-poor, carbonate-rich rocks found below ore and along normal faults at the Mount Tom Price and Giles Mini deposits. However, until recently such rocks have not been identified at the largest martite-microplaty hematite deposit, Mount Whaleback. In this study, samples of the upper Mount McRae Shale are examined for their chemistry, mineralogy and petrography. These samples were collected from several key locations, including within drill core that penetrates an area immediately beneath ore along the Mount Whaleback fault at Mount Whaleback. Compared to unaltered black shale from Wittenoom Gorge in the north and altered black and red shale at Mount Whaleback, reddish-green shale below the Mount Whaleback deposit is significantly enriched in MgO and CaO and depleted in SiO2. Samples of this shale consist predominantly of fine- to medium-grained dolomite and ankerite cut by chlorite and carbonate veins, contrasting with unaltered equivalents that contain mostly stilpnomelane, K-feldspar and relatively minor carbonates. This alteration is distinct from assemblages developed during regional metamorphism, and possibly represents hydrothermal alteration after metamorphism. Although several questions remain unanswered, these results support models that invoke an early hypogene stage during the formation of the martite-microplaty hematite deposits in the Hamersley Province.

Jan 1, 2005

By Bevilacqua P, Preti U

The basic separation phenomena taking place in film concentration processes are studied through a kinetic-probabilistic approach. This approach is based on the fact that the particle velocity in the film separation phenomena is a random variable and may be defined by frequency distributions and probability laws. The approach requires: 1. development of probabilistic models for describing the behaviour of particles having different specific gravity and size along selected trajectories in the separating devices; 2. setting up an experimental procedure for determining the relevant frequency distribution curves at the exit of the separators for the particles mentioned above; 3. estimation of model parameters and model validation. In the paper, the model equations are given for the mass distribution of particles on the surface of separators, the mass distribution at the exits of shaking tables and the residence time distribution in channel type devices. The relation between residence time distribution and particle velocity distribution is derived. The test procedure has been defined and results are reported for the exit or residence time distribution in channels. A comparison between experimental and calculated frequency distributions is reported.

Jan 1, 1993

By J Stiefenhofer

"*This is an abstract only*Construction of geological models for kimberlites has historically largely been based on visual volcanic textures and features, with chemical data only collected on an ad-hoc basis depending on the level of perceived complexity observed in the geological data. The focus of this paper is a high-level view of the impact an initial absence (or lack) of relevant chemical data had on two kimberlite resource models as well as how the magnitude of the problem increased once the resource estimation process commenced (Stiefenhofer, 2013). The impact of ignoring chemical data on a project assessment where micro-diamond estimation techniques are employed, is also discussed. Resource estimates based on micro-diamond data are critically dependent on the use of the correct geological model since stationarity of the size frequency distribution is key to the generation of correct grade estimates. A multilevel approach is advocated where the volcanological/visual model is verified using chemical data and both are in turn verified by the diamond data.CITATION:Stiefenhofer, J, 2013. The use of chemical and metallurgical parameters to enhance the economic value of kimberlite resource models, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 101-104 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By J P. R de Villiers

The Vanderbijl Park sinter plant in South Africa was investigated to determine the reason for the production of very fine sinter not acceptable as feedstock for the blast furnace. A procedure was designed to generate representative samples and to prepare the samples for chemical and mineralogical analyses. Results from a mineral analyser showed that the samples are extremely heterogeneous and therefore the sampling and sample preparation methods had to be tested in order to produce representative samples. The high production capacity at the sinter plant could also give rise to sampling errors. The method designed involved sampling of the conveyor belt at the sinter plant every four hours for the duration of three days. The samples were then milled and split into smaller sections appropriate for analysis. X-Ray diffraction (XRD) and X-Ray fluorescence (XRF) analyses were conducted on the samples. The results showed a standard deviation of less then one per cent, which indicates that the samples were representative and that the method used was therefore adequate. Systematic differences in the phase proportions between normal and fine sinter samples were detected, with the fine sinter containing more haematite than the normal sinter. The sampling method employed gives added confidence that the differences are real.

Jan 1, 2008

By N Weatherstone

A consistent and reliable international approach to public reporting of a mining companyÆs main assets, its Mineral Resources and Mineral Reserves, has become of increasing importance in recent years with the rapid globalisation of the mining industry. Through the efforts of the Committee for Mineral Reserves International Reporting Standards (CRIRSCO), a committee representing national resource/reserve reporting committees in Australia, South Africa, UK/Ireland/Western Europe, Canada, USA and Chile, the reporting standards in most æwesternÆ countries use almost identical resource and reserve definitions and are generally around 90 - 95 per cent compatible. New codes based on the CRIRSCO model are being developed or considered in other countries, including Peru and the Philippines. This unified approach has provided the mining industry, regulators and investors with a common framework to report and interpret mineral resource and reserve estimates, thereby facilitating funding to the mining industry through improved investor understanding and confidence. The common reporting standards are reflected in the CRIRSCO International Template, available on CRIRSCOÆs web site, a document that is kept æliveÆ by reflecting the best of the most recently published CRIRSCO-type national standards. In a significant exception to this unified industry approach, the USA Securities and Exchange Commission (SEC) requires adherence to its own standard, only partly compatible with CRIRSCO-type standards, with adverse and costly implications for companies listed in the USA. A major industry submission was presented to SEC in April 2005 which, if accepted, would bring about considerable compatibility of CRIRSCO and SEC standards. The UN Economic Commission for Europe (UN-ECE) has, since 1992, been developing its Framework Classification (UNFC) as a single global system for harmonising all existing national and international resource/reserve reporting systems, covering both government and industry requirements and both the hydrocarbon and solid minerals sectors. While few mining companies report their resources and reserves using the UNFC, the system is accepted or is being examined as a basis for reporting by some governments, including those of Russia, China and India. The UN-ECE agreed in 1999 to incorporate CRIRSCO definitions into the UNFC for those categories of resources and reserves used for market-related reporting, but a more recent edition of the UNFC removed or changed the definitions, requiring re-engagement by CRIRSCO to ensure compatibility. Since 2005, CRIRSCO and the Society of Petroleum Engineers (SPE) have been involved in discussions with the International Accounting Standards Board (IASB), which plans to develop a new Accounting Standard for the Extractive Industries as part of its International Financial Reporting Standards. At the request of the IASB, CRIRSCO and SPE have been examining any potential for convergence of resource/reserve definitions between the mining and hydrocarbon industries. Each of these systems is described in this paper and high level comparisons made.

Jan 1, 2006

The process of resource estimation of large precious metal deposits is illustrated by reference to major deposits now being mined or developed by Placer.The estimation procedure commences with building an appropriate model of the mineralization and proceeds through steps of data validation and geostatistical studies. It is important that the geologists most familiar with a deposit be involved with all stages of the estimate, and also prepare a manual estimate used to validate the kriged resource.Resource estimates are major exercises taking many man-months of work. The most time consuming part of this is usually construction of an appropriate three dimensional geological model. The data base for the resource calculations must be complete and checked for accuracy. The most appropriate estimation method must be selected.

Jan 1, 1990

By N LaBranche, G Callinan

There has been a reduction in overall workforce in the mining industry during the current downturn; a corresponding reduction in fatalities and high potential incidents (HPIs) has not been observed. The same contributing factors can be seen in the vast majority of these incidents. These include inadequate supervision and lack of adequate risk assessment. How management structures, trains and leads an operation can have a great impact on eliminating these factors and reducing the risk of fatalities and HPIs.Contractors now account for 41 per cent of full-time equivalent employees in the Queensland mining workforce, and are disproportionately represented in the majority of fatalities and HPIs. Having a clear strategy for how contractors are integrated into the workforce is crucial. This talk will include a discussion of the data as collected in the Department of Mines and Natural Resources department database, and offer solutions based on this data.CITATION:LaBranche, N and Callinan, G, 2016. Organisational factors in fatalities and high potential incidents, in Proceedings International Mine Management Conference, pp 201-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Deep hydrothermal fluids adjacent to the Alpine Fault move through the brittle-ductile transition to mix with convecting fluids from near surface environments. These tectonically driven fluids evolve mainly from prograde metamorphism at mid crustal depth (ten kilometres) within the ductile regime which has been elevated due to advection and drag on the fault plane. Through the onset of brittle failure and cataclasis within Alpine Fault mylonites, fluid overpressuring results in hydrofracturing and localized implosion. Along the length of the Alpine Fault, hydrothermal alteration varies on most levels (Table 1). There is an observable increase in Fe-Mg carbonate between the Waitaha and Taramakau Rivers (between Ross and Aurthur's Pass, respectively). Field studies concentrate to the north east of the Arahura River, noted for historical mineral wealth. Late meteoric fluids move through cataclasite, brecciated mylonite, and other open fractures. Chloritisation is the major retrogressive phase. Dolomitic hydrofracture veins (Figure 1) within coherent mylonites contain iron and copper sulphides. Notably, the enrichment in Fe-Mg carbonate towards the Alpine-Hope Fault intersection seems to represent a region of enhanced permeability possibly related to shallow seismicity, increased regional faulting, footwall variation, strike-slip dip-slip distribution, and/or topographical anomalies (ie saddles). Isotope studies identifying an 'Inboard Fault Gouge Calcite Zone' correlate to values from the Main Divide region at the headwaters of the Arahura River (Browning Pass-Wilberforce Valley) (Becker et aI, 2000). These correlations are supported by rare arsenic anomalies (avg l06 ppm n = 5, Figure 2) found in both regions which suggest that fluids may be interconnected at depth.

Jan 1, 2001

By H Bleuler

A new portal and access drift was constructed by Concrete Constructions for BHPÆs Elouera Colliery, south of Wollongong.The portal area at the base of the Illawarra Escarpment is in soft colluvium material, underlain by highly to moderately weathered sandstone. The area has a well documented history of slope movement or slope creep and one of the main criteria for the design was to minimise disturbance to the unstable slope by limiting the excavation for the portal establishment. This was achieved by incorporating a sloped headwall and gabion wingwalls to accommodate the anticipated creep and groundwater seepage.Main features of the design process also included the provision of both primary and secondary support in a single shell application and the use of canopy tubes to provide support ahead of the tunnel face.The active involvement of the designer during the construction phase and the flexibility of the design concept allowed changes to the support methodology to be carried out as excavation proceeded.This paper describes the design process undertaken for portal establishment and access drift to cater for the variability of the exposed ground conditions along the drift alignment.

Jan 1, 1999

By Davies L, Jeffreys J

The Broken Hill Proprietary Company Limited (BHP) has been successfully using mini computers in its open cut strip and pit coal planning for the past six years. A recent development within the computerised Seam deposit User oriented Mine Planning System (SUMPS) provides the facility for the generation, evaluation, and simulation of colliery workings.Existing computer programs for collieries were studied, but none met the requirements of BHP's underground mine planners.Consequently, it was decided to develop programs, based on those existing within BHP for open cut strip and open cut pit mine planning. The new planning facility was designed to enable any number of proposed colliery developments and operating plans to be evaluated against optimistic, most likely and pessimistic geological lease area interpretations.In mine planning, sensitivity studies should be conducted to determine the likely effects on production, development costs and colliery economics of changes in mine design and budgeted equipment productivity. By automating the manual calculations involved, the computer programs provide the ability to conduct numerous and extensive sensitivity studies. Hence an optimum mine design for budgeting purposes can be derived quickly with an improved degree of confidence in the long term viability of the proposed development.

Jan 1, 1982