Search Documents

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By N Khalili, J Zhao, G F. Zhao

Toppling failure of a jointed rock slope was studied by using the distinct lattice spring model (DLSM). Compared with the classical discrete element model, the DLSM has the advantages of free calibration of micro-mechanical parameters and easy to represent discontinuities, and is more computationally efficient. In this work, the DLSM was used to investigate the toppling failure of jointed rock slopes. The numerical simulation was verified against experimental data from a centrifuge model test on a jointed rock slope. Both the horizontal deformations and failure pattern observed in the centrifuge test were reasonably reproduced using the DLSM. Then, the mechanism of the flexural toppling failure was studied numerically by using a parameter analysis. Finally, some insights were derived that may be useful for practical engineering.CITATION:Zhao, G F, Khalili, N and Zhao, J, 2014. Application of the distinct lattice spring model on toppling failure of a jointed rock slope, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

By W Pytel

A special model of vertically loaded pillar behaviour is introduced to the general, multi-plate based, floor-pillar-roof system interaction analogue. This permitted analysing room-and-pillar mine systems in any geological conditions, including the effect of pillar elastic-plastic behaviour with strain softening. In the model, pillar instability is one of the important phenomenon, which may be expected to occur, and which the operator has to be prepared for. Thus the entire systemÆs safety is determined mainly by strong roof strata behaviour and therefore they have to be examined in actual stress-strain conditions utilising the appropriate strength theories. It was assumed that the so-called safety margin, representing the relation between load intensity and material strength, might serve as the basic indicator of possible roof instability development. Therefore, the safety margin may be estimated by comparing the actually computed components of stress-strain tensor with ultimate values characteristic for a given material determined in laboratory. In order to illustrate the effect of technological pillar size on roof strata stability, two different mining systems (methods of mining) in one of the æPolkowice-SieroszowiceÆ Mine districts was modelled using the finite element method formulated in three dimensions, assuming different materials within different rock mass strata, as well as a number of horizontal planes of discontinuity within the model.

Jan 1, 2003

Education and Training for the minerals industry has been identified as one of the key priorities by the AusIMM and many closely related groups. The AusIMM Education Taskforce has been engaged, through a visioning exercise, in evaluating what minerals education and training should look like by 2025. A common recurring theme is that for minerals education and training to be efficient and effective into the future, it needs to be comprehensive and inclusive. Some previous attempts to achieve efficiency and effectiveness have had limited success, mainly due to approaching the issues involved from a narrow, singular perspective. This paper outlines that the achievement of the desired outcome may require an approach that parallels the same techniques that are used for multi-dimensional mine planning, treating tertiary minerals education and training in a similar way to the planning involved for a complex orebody. Just as efficient and effective mine planning requires engagement and understanding of many factors, so too does engagement with tertiary minerals education and training. The major factors that need to be considered are outlined in the paper, including: levels of tertiary education and training; Australian Qualifications Framework (AQF), Levels 1 to 13: systems of minerals education and training, such as higher education, (mainly universities), industry/professional associations and licencing requirements, vocational education, (mainly TAFE) and workplace programs; types of minerals or mining methods involved; volume of delivery; stage in the flow sheet, (geology, mining, beneficiation, extraction, refining). For comprehensive mine planning there is the need to develop links or roadways and openings between different levels of a mine. Similarly, to achieve a comprehensive tertiary minerals education and training model, there is a need to develop pathways, recognition and credit transfer between the various levels and components of minerals tertiary education and training.

Jan 1, 2005

By J C. Macintosh

Capcoal Mine has modified its water use practices over the past 15 years. Two issues have changed the way water was managed:an economic review of water supply options for a planned expansion of the coal handling and preparation plant (CHPP) in the early 1990s, and increasing neighbour concerns about discharge of worked water from the mine into the local streams. These issues resulted in commitment by the site General Manager to cease discharge of worked water from site and to convert from using raw water to worked water in the CHPP. Operational needs, societal demands and continuing dry weather are again demanding change to the siteÆs water management strategy. This paper outlines the drivers for past and future operational change.

Jan 1, 2006

Peraluminous metamorphic rocks may form from a variety of protoliths by a range of processes. Stratiform bodies of such rocks are relatively common in the Precambrian, but less commonly, also occur in the Phanerozoic. The protoliths of such stratiform bodies may have been regionally deposited chamosite-rich sediments, with varying amounts of clastic component, or may have resulted from the in-situ depositional or diagenetic alteration of volcaniclastic sediments, ranging in composition from rhyolite to basaltic andesite.Stratiform peraluminous metasediments, especially those of low to medium metamorphic grade, and relatively iron rich, may be genetically associated with, or be the host rocks for, a variety of styles of mineralization, especially for the ores of An, Ag, Cu, Zn and Pb.

Jan 1, 1990

This paper describes techniques that have been used at RixÆs Creek Colliery to control blast vibration from throwblasts that face a residential area 4 km in front of the face. The paper describes blast design, face control including laser profiling, selective loading of blastholes after borehole camera surveys, and techniques used to assess the effect of burden variation, the cumulative effect of drilling and delay sequence, and the effects of meteorology.

Jan 1, 2001

By Y Hansen, J Petrie

Life Cycle Assessment (LCA) is increasingly being used as a decision-support tool within mining and minerals processing and metals production. However, a number of initiatives have highlighted the current limitations of LCA to accurately reflect the environmental performance of minerals and metals. These programs include:the Mining, Minerals and Sustainable development project (Stewart, 2001); the United Nations Environment Programmme/Society for Environmental Toxicology and Chemistry (UNEP/SETAC) workshop on LCA and metals (NRCan, 2002); the UNEP SETAC Life Cycle Initiative; and the review of the existing ISO 14 040 set of environmental management standards. Together, these initiatives highlighted concerns relating to the ability of LCA to engage with and support metals recycling, to adequately reflect the impacts associated with products from a multi-product orebody, the ability to adequately reflect the toxicity potential of metals in the natural environment and the fact that resource depletion focuses on mining (and not consumption) as the depleting activity in the life cycle of a metal. Additional impact categories to be included in LCA were also suggested. In this paper we demonstrate how existing initiatives are addressing LCA limitations. Finally we present the state of the art in Life Cycle Impact Assessment (LCIA) for two impact categories:resource depletion; and impacted land footprint for solid wastes.

Jan 1, 2004

By Yesil MM, Bozdag T

The swelling process is an impor- tant problem causing damages to the structures in or on swelling rocks, both during construction and operating life. To understand swelling problem, a number of testing methods have been developed by many researchers. In these studies, the swelling parameters, in most cases, are derived from oedometer tests. The swelling parameters determined from oedometer type tests represent one-dimensional behaviour (one-dimensional swelling law) therefore, it is quite difficult to extrapolate the oedometer type test results to the three-dimensional in-situ conditions. To overcome these problems, a three-dimensional approach is suggested for clay bearing rocks. Results of triaxial swelling tests conducted on marl from Dodurga Lignite Coal Mine are presented. Triaxial swelling characteristics of the marl are presented and design approach for tunnels is described.

Jan 1, 1992

By L Soares, W T. Hennies, F Fujimura

A methodology of environmental performance evaluation in mining developments is proposed, as well as guidelines and procedures for obtaining information to improve their environmental performance. Environmental performance is the results of the mining activities and their relation to environmental issues. If this evaluation is carried out on an on-going basis, it is possible to anticipate or to identify the formation and development of an environmental impact in its early stages. Evidence or trends identified by environmental evaluation provide valuable information to prevent further damage. The proposed methodology is based on the significant environmental aspects of a selected monitored job site by environmental indicators which are then compared with previously defined environmental criteria and targets or goals. The methodology procedures also take into account the environmental accounting of the investments and expenditures.

Jan 1, 2003

By C Pypno, P Nowakowski, T Opasiak, C

Belt conveyors are machines for continuous transport with most applications in mining industry in Poland. This is a result of simple construction and cheap operating costs. But conveying materials by belt conveyors are often in the powder state (eg small coal, gypsum, etc) and during the transport there is a possibility of polluting the environment around conveyor route. A good solution for this problem is the pipe conveyor, where a belt is closed on the route in circular shape and flat on unloading point. Another problem which is indicated in the paper is dusting on the belt conveyor boosters. In Poland a new solution of booster has been designed, whereby dustiness of transportation powder materials is reduced by up to about 90 per cent.

Jan 1, 2003

By D Johansson, C Yi, U Nyberg

Emulsion explosives are a common industrial explosive and have a non-ideal detonation behaviour. The detonation performance for a given product changes with the charge diameter, ground conditions, con?nement and density. The burning process of an emulsion explosive has been modelled with an ignition and growth model in the LS-DYNA code. The parameters in the burning rate function are calibrated by the detonation velocities and the detonation front curvature radii from emulsion explosive tests. A Perl program was developed for an efficient estimation of the parameters, and the results show that the calibrated parameters can predict both detonation velocities and the detonation front curvatures.CITATION:Yi, C, Nyberg, U and Johansson, D, 2015. Parameter determination of an ignition and growth model from emulsion explosive tests, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 585–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

A new gold cyanidation assay technique has been proven for a range of ores, where it has demonstrated benefits of being: ò Accurate (reduces the typical range of assay scatter almost three-fold, and avoids common fire assay interferences). ò Fast (under one hour, providing a quantum shift in space requirement and equipment utilisation each bottle roll can provide over 15 determinations per day). ò Simple (suitable for field application, no high skill or experience requirements). ò Profitable (reduced drilling, drilling time, ore misclassification and/or double handling after mining). ò Cheap (far lower cost than Fire or Aqua Regia Assays, ie LeachWELLTM costs around 10ó for a 20 g sample at 50 per cent solids, proportionately greater for larger samples eg $1 for 200 g samples which address most nugget effect problems). ò Relevant (distinguishes economic. ie cyanide-extractable gold, the only unequivocal value to use for true resource definition, mine planning and grade control). ò Robust (rough bucket chemistry of samplers does not seriously affect results). A new development is the provision of LeachWELLTM CAS, a solution, which also contains optimum cyanide and stabiliser concentrations; and offers greater: ò Safety (the dilute cyanide solutions are stabilised to avoid generating toxic HCN vapours; and present no cyanide dust or flying chips to deal with). ò Ease (a single squirt dispenses precise quantities of the entire reagent suite, avoiding multiple weighings). ò Reduction in total reagent costs. An inter-laboratory comparison on nine ore types, using two assay techniques (Fire Assay and Aqua Regia) involving 45 laboratories, has demonstrated that LeachWELLTM 60X assays for the samples tested, were equally or more reliable than typical Fire or Aqua Regia Assays. There is particularly great benefit in applying LeachWELLTM 60X assays to richer ores in comparison to Aqua Regia assays, which appear to be prone to very significant underassaying depending on individual analyst skills, and which often suffer greater nugget effects. The major impacts for heap leaching are that: ò Using the LeachWELLTM assay technique for grade control, ore of marginal grade is not accidentally discarded to waste or visa versa due to the scatter of assay data inherent in typical small charge (25 g) fire assays. ò LeachWELLTM assays very importantly report only that gold which will be recoverable in the heap, viz that which is liberated - an important factor where the coarse crush often leaves ten per cent of gold unliberated. These impacts are of particular importance for many ores (ie most of those recovered from open pit operations and at the margins of rich ore subject to slurry processing) subjected to heap leaching as the oxide zones often present major problems of nugget effects as well as mineralisation that cannot be accurately assigned through interpretation of clear structural controls.

Jan 1, 1994

By Waghorn EP, Gleeson HB

The Loy Yang Optr, Cut is a brown coal mine bring developed in the Latrobe Valley region located some 160 kin south-east of Melbourne, Victoria. The mine has been designed to supply a mine mouth power station at a rate that will rise to 32 million tonnes per year by the mid 1990's. Continuous mining metnuds are employed using bucket Whtel excav- ators and conveyors. This paper describes the basis of the design of the Loy Yang continuous mining system ano cne experience of four years of initial operation.

Jan 1, 1987

This paper deals with the extension of Post Office telecommunications (telephone, data, leased private lines etc.) network to mining communities in remote areas of Australia. The evolution of the "Spur Line" policy and its application is referred to together with comments on the engineering of telecommunication Facilities.

Jan 1, 1973

By Christie AB

Stream sediment geochemical analyses from 140 mining company exploration surveys of the Coromandel, Northwest Nelson, Marlborough and Westland regions of New Zealand have been compiled from open file reports and entered on a database called REGCHEM (for Regional Exploration GeoCHEMistry). REGCHEM is supported by GEOEXPL, a custom-written computer software application which operates under the Microsoft Access relational database mangement system on a PC-type computer. The data are plotted as maps using the Maplnfo geographic information system (GIS) package. Thesholds separating anomolous values from background values are determined using the PROBPLOT univariant statistical package, which enables the descrimination and modelling of several populations. Relevant REGCHEM data are being incorporated into a GIS for the Coromandel region as part of ongoing studies to sevelop mineral deposit and metallogenic models for the region, and to assess regional prospectivity.]

Jan 1, 1995

By P Hartlieb, M Noeger, M Varelija

Rock bolts are important in underground mining as they provide support to the rock mass around the excavation. They are the most common reinforcement method in mining and civil engineering excavations. The length of the bolts, types and spacing between them can be varied, depending on the reinforcement requirements and the use case (Kolapo, Onifade and Praise, 2022). The rock bolt provides safety and stability for the rock mass in the excavation area and they can be mechanically anchored, grouted, or friction anchored. They normally don’t have a measurement option and there is a possibility that it failed without showing visible signs on the surface, especially in grouted rebar bolts where they can still have some residual strength. Therefore, support functionality can be lost without recognising it. To overcome that, sensors can be installed on all three previously mentioned bolt systems. Intelligent bolts with implemented measuring systems have a function of showing changes and indicating if there is some damage on the bolt. So, it can be said that intelligent rock bolts are regular bolts equipped with additional instruments which are helping us detect potential instabilities inside of the rock mass or malfunction of the bolt itself. Changes in rock mass can be tracked, by measuring rock bolt reaction concerning the excavation response. Rock mass damage and instabilities are therefore measured in terms of rock mass deformation. Moreover, other additional information depending on the type of the sensor device could be collected. Based on such measurements, information about rock mass state can be derived. Different rock bolt types work at different reaction principles. Therefore, limitations on sensor application and information that can be extracted must be considered.

Sep 1, 2024

By Ribicic M, Kocar F

Surface lakes or water accumulation present a possible threat for the flooding of the underground mining works. Therefore, the criteria that define the conditions under which no flooding of the mining works can occur are of vital interest to the miners. The authors present the criteria that they developed for the Velenje lignite mine, Yugoslavia, and that take into account the elastoplastic behaviour of the rocks and the natural stresses involved in the deformable strata between the bottom of the lakes and the mine works as well as the extent of the direct caving-in process resulting from longwall mining activity. Fi- nally a generalization of these criteria to the other rock and stress conditions is discussed.

Jan 1, 1988

By P D. Munro

The spatial distribution of ore with similar processing properties or domains within an orebody may be identified early in the assessment of an orebody to provide a sound basis for later development of the orebody. The assignment of domains in the primary sulfide portion of an orebody is often more difficult than recognition of the oxidised, supergene and related domains usually located towards the top of the mineralised volume. This paper will discuss some approaches to assigning domains within the primary sulfide portion of an orebody. The processing properties of each mining block will be known if the contained domain(s) and their proportions are known. The use of both physical and chemical ore properties to assign the domains is discussed. The domains based on similar processing properties do not necessarily coincide with geological zones assigned by geoscientists. As part of assessing the physical properties of ore, the modal analysis of the ore with respect to the valuable sulfide minerals and the sulfide and non sulfide gangue minerals has to be known, along with the traditionally used elemental assays for valuable and penalty elements. Two scales for determining other physical ore properties will be considered: the mesoscopic scale (examined by human eye) and the microscopic scale (examined via a microscope under high magnification). The strengths and weaknesses of the data obtained at the two scales are discussed in the paper. Broadly, data collected at the mesoscopic scale are much less expensive but the types of data available are more limited. Methods for evaluation of chemical ore properties are also discussed. After establishing a basis for establishing the spatial distribution of domains, variability testing is required to verify the integrity of the designated domains. In contrast, each block of ore in some orebodies has been assessed principally via the results of a laboratory separation on a number of drill core samples or composites from throughout the block, with minimal or no attention to the concept of domains.

Jan 1, 2008