Search Documents

The Granites Gold Mine has far exceeded the design capacity of 300,000 tonne per annum during its first sixteen months of operation. The presence of considerable free coarse gold has made it imperative that the gravity section operate at maximum efficiency. The inadequacy of acid digest- ing facilities and trying climatic conditions prompted management to initi- ate investigations into the use of Intensive Cyanidation as an alternative method for upgrading gravity concentrates prior to smelting.

Jan 1, 1988

By Dorricott M. G

Rock bolt installation is generally carried out in two steps. First the hole is drilled and the drill steel is extracted, then the bolt is inserted into the hole and tightened or grouted. With single pass bolting (SPB), however, these two steps can be carried out at the same time. This kind of bolting system has at least three advantages, (1) the time used for the bolt installation could be reduced, (2) the condition of safety for the operators could be improved, and (3) the degree of automation of the rock bolting practice could be increased. The study presented in this paper is concerned with the development of the SPB system. The current state of the system is discussed, and further improvement of the technique is explored.

Jan 1, 1992

By Stevenson C. H, Lynch A. J

The reasons for choosing autogenous grinding for the new Warrego concentrator of Peko Mines N.L. are discussed and the ores to be treated in the concentrator are described. The mill was designed on the basis of pilot tests carried out at Cobar and the performance of the mill has been most satisfactory both in its metallurgical and mechanical aspects. An empirical technique has been developed to predict mill performance for change in feed rate or feed size and a mathematical model of the mill is being developed for simulation and control work. The weight and size distribution of the mill load was determined at one set of operating conditions for use in the mill model.

Jan 1, 1974

Synthetic hollow microspheres have demonstrated reliable sensitization and detonation characteristics in industrial explosives for almost two decades. During that time, water gel formulations and use conditions have changed. The introduction of emulsion explosives has also dictated technical improvements in microsphere sensitizers. In contrast to microspheres, gassing or other sensitizing techniques often cannot satisfy the manufacturing and blasting characteristics required of today's explosives. This paper discusses the sensitizing properties of microspheres, formulating guidelines and quality considerations. Packaging, sampling, transfer, metering, mixing and pumping information is also provided.

Jan 1, 1990

By Hongzhen Yu, Xiaoping Ma, Jiansheng Qian

The paper introduces the design of an Intelligent Managerial Attendance Machine (IMAM) for coal mines. In the system, data communication is carried by Optical fiber communication, including industrial control computer on the ground and the car

Jan 1, 1998

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By W Mackinnon

Coal mining operations require the expenditure of appreciable start up and working capital in order to produce saleable coal for domestic or export markets. The competitive nature of the coal business restricts margins, and so it is imperative that downside risks, in terms of production outcomes, are minimised. The major risks identified for a coal mining operation, aside from sales volumes and coal price, are generally thought to be confined to the geology of the deposit and the mining process. However, the impact of product quality and yield can be very significant. If product coal is inferior to projections, then it will need to be sold at a discounted price and this can dramatically impact on margins. Equally, if yield is five to ten per cent less than planned, then this will have a huge effect on profitability. This paper will look at issues relating to in situ moisture and density, resource quality evaluation, modelling of washability and dilution, and simulation techniques, and how best practice approaches can be incorporated into mine planning and feasibility studies. Risks are best modelled and understood by adopting a detailed approach that is fully documented and auditable. This is particularly needed for multi-seam and multi-product operations. Once a well defined systematic approach is established the potential risks can be evaluated by testing different scenarios, carrying out sensitivity analyses, variability modelling and examining extreme operating conditions. These have been discussed in the paper, along with some related issues such as the cost of quick fixes and the value of spending a little more in the coal preparation area.

Jan 1, 2003

The ""multiple of exploration expenditure"" method of mineral valuation is applicable to exploration properties from the earliest stage of exploration to a moderately advanced stage but for which no resources have been delineated. While not recommended as a primary valuation method by some workers, others believe it to be the most satisfactory method of valuing exploration properties until it is possible to employ a DCF technique. In many situations facing the professional valuer, the method may represent the only semi-quantitative option available and is frequently used. Significantly it often forms the starting point in discussions to farm-in on an exploration tenement. The paper briefly reviews the definition of value as applied to mineral valuation and in particular examines the relationship between fair value and market clearing price in ""fair"", bull and bear markets. The multiple of exploration expenditure method uses previous exploration expenditure and/or future committed exploration expenditure to derive a base value for the tenements. This base value is multiplied by a prospectivity enhancement multiplier (PEM) with adjustments for market premium or discount and consideration of the quality of the exploration team to derive a fair value for the tenements. The paper will demonstrate that there is no necessary nexus between fair value derived from the method and present book Values.

Jan 1, 1994

Several coal preparation plants are presently "automated" to the extent of automatic sequencing and interlocking via digital means, together with closed loop control on various level and density circuits. This paper will explore the potential for second generation automation utilizing on-stream ash analysers and other measuring elements so as to optimize the total metallurgical process. This would enable maxim-ization of recovery, improved product homogeneity and minimum reagent consumption.

Jan 1, 1985

By P Krauss, S Harpalani

Methane emitted from underground coal mines, along with ventilation air and known as ventilation air methane (VAM), constitutes the largest component of coal mine methane (CMM) emissions. Atmospheric methane, on the other hand, is a potent greenhouse gas with a significant adverse impact on the atmosphere. This has led to the development of various technological alternatives for its use as an energy fuel. Techniques involving oxidation of VAM, usually consisting of very low concentrations of methane, have been validated in the past. Prominent among these technologies are the thermal and catalytic flow reversal reactors, ancillary fuel technologies, lean fuel gas turbines, and concentrators and gasifiers. However, the efficiency of any VAM utilisation technique depends on the amount and concentration of methane in the ventilation exhaust air. Therefore, quantification of VAM emission from a coal mine is the first step towards identifying the most suitable technology for its utilisation for energy production. This paper presents an evaluation of the efficacy of VAM as an energy source. It provides details of a case study aimed at developing a technique to accurately quantify VAM emission from a coal mine. It further discusses the various VAM utilisation techniques available, and presents an economic evaluation of the alternatives. Based on the findings of the study, the most feasible method for VAM utilisation is identified for the mine. The paper summarises the procedure for quantifying VAM emissions and selecting the most suitable utilisation technique.

Jan 1, 2005

By Avraamides J, Ritchie I. M

Gold Tellurides are important sources of gold at Kalgoorlie, Western Australia, Cripple Creek, Colorado and Vatukoula, Fiji. Unlike free gold, the tellurides of gold are rather refractory and the usual treatment practice has been to oxidize the tellurides, either chemically or by roasting prior to cyanidation of the liberated free gold. There is a large measure of disagree- ment as to the actual cause of the refractory nature of gold tellurides. In order to investigate the leaching chemistry of gold telluride, a study was undertaken on the thermodynamics and kinetics of its dissolution using electrochemical methods. From this study suitable direct leaching condi- tions are suggested. In acidic chloride solutions gold telluride can be leached using iron(III) as the oxidant. At lower acid concentrations the reaction is controlled by the formation of a passivating film of H2TeO3. In alkaline solutions containing cyanide the rate of gold telluride dissolution increases with increasing pH and strength of oxidant. However, this can result in excessive consumption of cyanide in the presence of stronger oxidants.

Jan 1, 1991

By De Janti VP

The automation and centralized monitoring of longwall type underground mining is presently an important subject matter of research in France. The purposes are :to improve safety and working conditions to increase productivity.to improve efficiency in machine operation through continuous "health monitoring". to make winning possible in difficult seams.

Jan 1, 1985

By Sims D. A

This paper primarily describes the application of geology to the different mining methods employed in a large underground mine. The steeply dipping stratiform Silver/Lead/Zinc mineralisation at Mount Isa include up to 28 mineable orebodies. The orebodiea are mined by cut and fill, sublevel benching and sublevel open stoping; the method chosen depending mainly on orebody geomechanics.The sources and methods of data collection, and the interpretation process undertaken, are described. The paper emphasises the different geological input required, by each individual mining method, to provide the necessary production and strata control. This input contributes significantly to the success and efficiency of the operations.

Jan 1, 1990

By Riley TW

This paper describes a Process Simulation Package for modelling the steady-state operation of a mineral processing plant. There are two levels of input allowed into the package. The first allows simple manipulation of the process models within a defined modular format which enables a wide range of process systems to be simulated. "The second level of input is via a Command file which allows plant models to be defined and changed without reference to the code or the requirement of any recompiling of the programme sources. The Command file interface was designed for use by metallurgists and assumes a sound knowledge of the system being modelled. As such it is an effective tool for metallurgists rather than a user friendly generalised package for the layman.

Jan 1, 1985

The Western New South Wales Electric Power Proprietary Limited is the central generating authority for distribution of power to the majority of the Broken Hill mining companies and the Broken Hill Water Board. This station supplies the whole of the power to North Broken Hill Ltd and Broken Hill South Ltd. It also supplies, power to the Southern Power Corporation for distribution to the Zinc Corporation Ltd. The Southern Power Corporation has a generating station which is tied in with the central generating authority.

Jan 1, 1957

Tholeiitic metabasalts comprise at least five geochemically distinct mafic volcanic associations of Late Palaeozoic age within the Gympie Province, southeast Queensland. Geochemical features indicate that parental magmas of the various metavolcanic suites were generated in contrasting tectonic regimes, although each of the suites shows some affinities with eruptives from convergent plate margin settings.Basalts from the Highbury Volcanics of the Gympie Group are island arc tholeiites (IAT) formed during an immature stage of eruptive activity in an intra-oceanic arc. They are unique among the analysed metabasites in possessing high Zr/Nb (Zr/Nb - 30) and very high Ba/Nb, and as well as low Ti/V, Ti/Zr and Ti/Y. These features are explicable solely in terms of contributions from a depleted, convecting upper mantle source, and large ion lithophile element (LILE) enriched fluids ascending from subducted oceanic crust.

Jan 1, 1990

The great philosopher, Marshall McLuhan, is said to have stated that the use of forecasting as a means of guiding future actions is akin to driving an automobile through observations made in the rear-view mirror! In effect, in forecasting it is assumed that there will be an orderly progression from the past into the future, and that the model will be sufficiently unvarying for use to gauge both the directions and the rates of change. The concepts of forecasting have served man well in disciplines in which the relationship between causes and effects can be clearly demonstrated; such as between rainfall and crop yield, for example. These are of no value, however, when conditions change rapidly and unpredictably, or when there is no model at all. Even worse, under such circumstances our preconceived notions may cause us to make some horrendous errors in judgement. Such are the risks at present in attempting to make an assessment of the educational needs of the minerals industry for the coming century! The model, and the conceptions that we have had of the linkages between cause and effect are in disarray. Minerals markets are chaotic, and there is almost no ability to forecast trends in metal values. Linkages between supply and demand seem tenuous. Internationally, producers are struggling for survival. Mine closures, temporary shutdowns, and reopenings are frequent occurrences. Decision-making under uncertainty is probably one of the most certain things about the world mining industry Today!

Jan 1, 1986

By Yoon R-H, Luttrell GH

A theoretical model has been developed to predict the probability of particle collection by air bubbles in a quiescent flotation pulp. The model considers the effects of both hydrodynamic and surface chemistry forces acting during the bubble-particle interaction. Hydrodynamic forces considered include the gravitational, buoyancy, streamline and film thinning resistance forces. The surface chemistry forces considered include the electrostatic, dispersion and hydrophobic forces. The hydrophobic force has been estimated from extended DLVO theory. The model is capable of predicting hydrodynamic and surface chemistry conditions under which bubble-particle adhesion is possible. Validity of the model has been verified experimentally.

Jan 1, 1993

By Nyamekye GA, Subramanian S

Adsorption tests have been carried out to elucidate the interaction mechanism between dextrin and sulphide minerals. Sulphides such as galena and heazlewoodite exhibit high affinity adsorption over the pH range that coincides with the iep of lead and nickel hydroxides, and is suggestive of chemical interaction. The adsorption behaviour with respect to the sulphides of copper is of the low affinity type, and follows a different pattern. The adsorption studies on graphite, support the chemical interaction mechanism, with the metallic impurities serving as adsorption centres. In conformity with the proposed mechanism selective separation of galena from chalcopyrite and heazlewoodite from chalcocite has been Achieved.

Jan 1, 1993

Selective continuous surface mining is a rapidly developing system of mining which will have a significant impact on many present and future open cut mines. In many aspects the technology is in its infancy, whilst in other facets concepts drawn from other sectors of engineering are well proven. Full development of the potential and benefits of this technology will only be achieved if the mining companies and manufacturing companies work together to produce machines which the end user really wants.

Jan 1, 1986