Search Documents

The variation of austenitic grain size with temperature for the steels XKSlSO and XK9261 was determined using the vacuum ctching technique.It is shown that the effect of temperature on the mean grain intercept is relatively small, up to approximately 950°C. Above this temperature the rate of increase of grain size rises sharply.Within the limits of the 1-4 hr vacuum etching times used the effect of time at temperature is relatively small on the ASTM grain size of the steels.

Jan 1, 1967

By D S. Nicholson, T Marshall

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while opencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

By C J. Stanley

Reflected light optical microscopy, or epimicroscopy, is one of the oldest techniques of modern mineralogy. At a relatively low capital cost, it is also very resourceful, and the analytical choice for the identification of most ore minerals. In ore mineralogy, reflected light optical images have the potential to overcome the main limitation of backscattered electron images from scanning electron microscopes, namely contrast of mean atomic number  below the spectral resolution of the backscattered electrons detector. This is the case for relevant ores, like iron (haematite-magnetite) and copper-zinc ores (sphalerite-bornite), but for both cases the pairs of minerals are easily discriminated in reflected light. The improvements in optics and electronics also made microscopy a powerful source of digital images, suitable for automated analysis for minerals processing, as the determination of liberation spectra. The drawback, however, has always been the impossibility to recognise the transparent minerals, which account for most of the gangue phases in ores, from the embedding resin, usually epoxy. In order to determine if there was any possibility to separate quartz from epoxy resins, reflectance spectra have been acquired for quartz and some commercial epoxy resins (Araldite, BuehlerÆs Epothin and Epocolor, Araldite spiked with fluorochrome from Struers), from 380 to 720 nm in 5 nm intervals. Reflectance of quartz and epoxy is very similar over the whole visible light range, and varies from 4.5 to five per cent. Epocolor, a red-dyed epoxy, reflects slightly more above 560 nm, as does Araldite spiked with the fluorochrome from 460 to 570, but for both the reflectance is still very close to that of quartz, under 5.1 per cent. This data set is final, and precludes the application of reflectance in light optical image analysis for assessment of liberation, phase quantification, or any other signal that requires separation of resin from transparent minerals.

Jan 1, 2008

By K Matsui, R N. Gupta, H Shimada

Roof falls and failures of powered supports were major threats at longwall face. Abnormal geological conditions were caused roof falls and shield damage. Therefore continuous monitoring and analysis of strata behaviour was imperative on real time for forecasting adverse behaviour. Novel PXI instrumentation system was successfully developed for continuous monitoring and analysis of supports pressure, leg closure and gate roads convergence. However, this paper briefly examines the novel gate roads convergence monitoring system with field applications.

Jan 1, 2003

By Teniswood CF, Sheppard I, Mason LG

An industry initiated project, sponsored by the National Energy Research Development and Demonstration Council, has worked for two years in developing design guidelines for underground coal mining machinery.Continuous miners and shuttle cars were selected for the initial development of design guidelines as these machines were linked with 7500 lost workdays and 490 reported injuries during the preceding two years.

Jan 1, 1991

Prefeasibility planning and cost estimation of conveyor systems has historically been undertaken by comparing fi xed plant transport requirements to that of similar systems in service. This paper describes the development of a prefeasibility conveyor technical design and cost estimation application using Microsoft Excel Visual Basic for Applications (VBA) platform. The application tool known as D-Convey (Dachshund Convey) was developed with the goal enabling the end user: to develop a technical model for conceptualised conveyor systems, to perform economic analysis on the developed technical model, and to conduct a comparative and risk analysis. An Excel VBA based platform was utilised to draw upon both the analytical and graphical capabilities of a spreadsheet. Some of the features of D-Convey system include a revolutionary dynamic graphical help system, known as the 'information pane' in lieu of traditional help fi les as well as the use of familiar graphical user interface elements such as the MS Offi ce 2007 task ribbon. The D-Convey system incorporates material database allowing for mass handling prefeasibility estimation in other industries; it has been validated at a local quarry.

Dec 6, 2010

By Reichman J, Chapman G

The features of seam gas drainage from the point of view of mathematical modelling are outlined and discussed: 1. The use of conventional single phase gas reservoir simulator for very simplified modelling. 2 Alteration of a conventional petroleum reservoir simulator into a specialised simulator for seam gas drainage. 3. Application. of a conventional petroleum reservoir simulator for modelling of seam gas drainage by the way of pseudo-functions and sacrifying one dimension.

Jan 1, 1982

By R Berry, J Hunt, T Kojovic

Geometallurgy aids the understanding of orebody variability through the integration of geological and processing information, thereby enabling spatial mapping of processing (eg comminution or separation) performance across a deposit. In order to do this, estimates of quantitative geometallurgical attributes are needed so that continuous downhole profiles can be generated for each attribute, providing vital data for the development of processing domains through geostatistical modelling. However, as traditional comminution tests are high cost and/or require large samples, current practice typically results in insufficient data density and distribution of comminution indices making it difficult to model and map deposit scale variability. The aim of this work was to find a method to estimate comminution indices based on data that is widely available at mine sites. This data includes mineralogy and chemistry of drill core samples, plus logging information such as lithology and alteration. Work to date indicates that comminution parameters such as semi-autogenous grinding (SAG) Power Index (SPI), Bond Work Index (BWI) and A*b (Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight test (DWT) Index) can be modelled using chemical and/or mineralogical data. The estimated hardness indices can then be propagated into the mine site database and used in the definition of processing domains that map inherent variability across a deposit. The estimates can thus provide geometallurgical inputs for spatial modelling, mine planning and optimisation initiatives.CITATION:Hunt, J, Kojovic, T and Berry, R, 2013. Estimating comminution indices from ore mineralogy, chemistry and drill core logging, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Marshall T, Nicholson DS

Reserves of high-grade quartz gravel, lignite and timber suitable for the production of silicon metal and ferrosilicon on large scale occur within 40 miles of Bluff Harbour. Undeveloped hydroelectric power resources on the Clutha River are located within 50 miles of the most promising quartz gravel deposits while ooencastable lignite, potentially suitable for electric power production, occurs in the same locality as the quartz gravels. A preliminary study of production economics indicates that the commercial feasibility of silicon/ferro-silicon production would depend mainly on the cost of electric power, total capital cost of plant, and the market value of the products. The proximity of Bluff Harbour is advantageous for the export of products.

Jan 1, 1971

The cost of production from truck and loader fleets is influenced by management development of the culture of the organisation, work practices, systems and procedures of the production and maintenance teams. Establishing if the cost of production is the best that can be achieved then requires the measurement of results against established standards of performance. This paper provides a series of discussion points of the factors that influence the cost of production from men and machines for large scale open pit mining operation and provides some suggested performance standards in the form of Benchmarks. Most of the references have been drawn from established large scale deep pit mines in USA, Canada and Australia which have had to implement and constantly fine tune cost efficiencies in order to survive. The discussion provides:ò a review of priorities or the relative importance of the various cost elements for a mining system;ò suggestions of systems and procedures for the operation and maintenance of machines which are considered to yield the best overall results;ò examples of operations that have developed and implemented management systems and controls that are achieving good results in specific functions; andò suggested benchmarks of performance.

Jan 1, 1992

By Woodcock J. T, Rummel P. H, Sparrow G. J, MacRae C. M

A rapid automated search method, developed for the location of native gold grains in polished sections with a scanning electron microscope (SEM), has been extended to locate platinum group elements (PGE), in particular platinum and palladium, and their minerals down to 1 ¦m in size. Problems associated with the search for PGE minerals are discussed and examples of PGE minerals located with the facility in drill core sections, crushed ores, and metallurgical test products are given.

Jan 1, 1991

By M A. Etheridge

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems are particularly prone to developing tile complex fracture arrays, extreme local dilation and dramatic increases in permeability that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits. The arc systems of tilePacific rim are typically structurally and tectonically complex. At any given period in the evolution of an arc system, it may be dominated by extensional, compressional or strike-slip deformation. Indeed, it is common for the tectonic environment to change repeatedly through the development of a single arc segment. As a result, structures formed in one tectonic environment are commonly complexly reactivated in quite different environments later in arc evolution. These complexly reactivated structures have greater potential to localise extreme fracturing, dilation and fluid flux than primary structures. Application of this knowledge to practical exploration requires an understanding of the primary geometry of the controlling fault systems, the fault movements during reactivation, intrusion and mineralisation, and the consequent location and geometry of dilational sites. Simple 2D lineament analysis and targeting on lineament intersections does not suffice. Chemical processes that results from structurally focussed fluid flow may also contribute to permeability enhancement and further enhance fluid flux. Two main types of chemical feedback are important. The first involves selective dissolution of minerals during alteration and tile consequent production of increased porosity and permeability. The second occurs where alteration changes the mechanical properties of tile rock mass, especially where it leads to a greater propensity for fracture (eg by silification). In near-surface environments (< ~1 km), geomorphic processes complement fault systems in focussing fluid flow to develop sub-horizontal bodies of mineralisation, such as the giant Ladolam gold deposit (>42 million ounces of gold).   Along with classification schemes which stress crustal level, host rocks and alteration assemblages, the styles of high level 'epithermal' and reated deposits must also be considered in respect of their controlling co-active fault structures. Such structural understanding, combined with understanding of tile chemical processes involved (eg host rock reactivity), provides a major tool for exploration particularly in terrains obscured by deep weathering. Geological interpretation based on integration of field mapping with magnetic, radiometric and other remotely sensed imagery provides a powerful complementary tool to the traditional geochemical and geophysical targeting techniques. Timely and effective geological input is capable of reducing exploration risk and providing a more cost-effective basis for drilling and development. Examples of deposits associated with fault reactivation in extensional, compressional and strike-slip settings within arc systems are discussed in this context.

Jan 1, 1995

By B Stewart

The SRS-1200 concept came about following the recommendations from the Board of Inquiry into the 1994 Moura No 2 mine disaster with the aim of having a system to remove personnel from an unsafe environment underground via a shaft where no other means of escape is possible. It is a mobile rescue unit that utilises a winding system to operate a man cage. It can descend the cage up to 1200 m into a vertical shaft. This operation is managed from the winder control compartment located on the non-driver side at the rear of the vehicle.

May 5, 2022

By Sen G

An amount of explosives, whether it be cylindrical, spherical, etc in configuration, with a hollow cavity in one face or end is known as a hollow or shaped charge. When this charge is initiated, a focussing of explosive energy will occur within this cavity. This focussing, or concentration of detonation products creates an intense localised force greater than just the simple detonation of a conventional explosive, (without a hollow cavity). If this hollow cavity explosive is directed against a target material this concentrated force is capable of creating a deeper penetration than the same amount of explosive without the hollow cavity. If a metallic liner material is used in the hollow cavity, upon detonation of the explosive this liner will form into a high velocity penetrating jet. Depending on the explosive type and the liner material's configuration the jet tip can travel up to 10 km/s. Linear shaped charges were developed using the abovementioned shaped charge concept but instead of being formed about an axis, they are elongated and constructed along the principal axis. Therefore instead of creating a narrow circular penetration jet, it forms a thicker planar cutting jet ideal for linear cutting purposes. Using Linear Shaped Charges (LSC) for pre-splitting is expected to result in more accurate directional fracture propagation, while minimising lateral micro fractures in the surrounding rock mass which is required to remain undamaged.

Jan 1, 1995

Difficult ground conditions in the area planned for placement of vent rises to the surface at the Porgera Goldmine led engineers directing the project to chose blind shaft boring methods of shaft construction from the available alternatives. Zeni Drilling Pty Ltd was first contracted in 1988 to install a group of three closely-spaced, steel lined shafts. The success of these led to an order for a fourth hole in the same group followed by two more, less than a kilometre. away, under a separate contract in 1992. All of the shafts were completed on.schedule to within one day. The only significant difficulty arose during commencement of the last shaft when the strata collapsed trapping the drilling tools and jeopardising the stability of the surface collar pad. The situation was corrected by innovative lining techniques and the project went on to finish on schedule. This paper discusses the application of various technologies associated with the project including aspects of geotechnical input, drilling fluid chemistry, mining engineering and logistics.

Jan 1, 1993

This paper discusses design concepts in planning a large modern bulk terminal. The need is emphasised for a studied master plan, in-built materials handling flexibility and staged development. An integrated approach is advocated, combining functional purpose designed foundations and structures to serve their mechanical, electrical and environmental functions. Dry bulk and slurry handling are also compared in perspective.

Jan 1, 1983

By S R. Grano, J Duan, T A, D Fornasiero

We have determined the experimental rate constants for chalcopyrite particles floated from a complex sulfide ore and compared them with those calculated using a recently developed flotation model. The model incorporates contributions from the efficiencies of collision, attachment and stability between particles and bubbles, as well as their frequency of collision. For these calculations, the contact angle of the chalcopyrite particles in the ore was obtained independently using a surface spectroscopic approach. The calculated flotation rate constants were in good agreement with the experimental data and able to reproduce the characteristic maximum in flotation rate constant for particles of intermediate size. The values of bubble velocity and turbulent dissipation energy derived from these calculations are relatively low and may well correspond to mean values of these parameters inside the flotation cell. We have extended this approach through the application of a property based model to an operating plant, with a satisfactory outcome.

Jan 1, 2005

By Frost M. T

Magnesium is the lightest metal used in structural applications but these are only a small part of magnesium usage, with the use in aluminium alloys consuming half the magnesium produced. Other applications include steel desulphurisation, nodular iron manufacture and metal reduction. Demand for magnesium is expected to increase towards the end of the decade because of a requirement to lighten the weight of automobiles. The current western world plant capacity and production rate is 250 000 tpa. The CIS and PRC also have production capacity but shipments from these countries have been limited in the last half of 1994. The price for magnesium has followed trends similar to aluminium with recent recovery from US$1500 per tonne in 1992 and 1993 to US$4000 per tonne in 1995. The major magnesium producers all use different production methods and the potential exists to establish a large-scale magnesium industry with operating and capital costs comparable to aluminium. The Australian Magnesium Research and Development Project has been established to develop a low cost method of production using the magnesite and infrastructure resources in Central Queensland.

Jan 1, 1995

A generalised mathematical model for hydrocyclone classifiers was developed by the author (Nageswararao, 1978) using dimensionless groups which include phenomenological characteristics as independent variables. This model is incorporated in JKSimMet, the steady state mineral processing simulator developed by JKTech.Recently, when this model was rewritten (Lynch and Morrell, 1992), in terms of variables other than those used by the author, a few errors have crept in. For example, while the exponent of (Du/Dc) in the equation for d50e should be negative (-0.47), it was recorded as positive (0.47). Also, the exponent of (DoIDe) in the equation for pressure drop should be 0.67 and not 0.60. In the same equation, the exponent of Dc would turn out to be -0.10 and not 0.15. These are clearly attributable to typographic and rounding off errors, while transforming the original equations.More recently, Cilliers (pers comm) has done a comprehensive evaluation of the major semi-empirical models for hydrocyclones.He observed that the major difference between the cyclone model developed by the author and other models lies in the method of quantifying the effect of spigot diameter on d50e. He noted that while all other models predict an increase in d50e with a decrease in the spigot diameter, the model as cited by Lynch and Morrell (1992) predicts just the opposite. However, he conjectured correctly that the discrepancy could be due to a typographic error. As the model is still unpublished, it is felt that the original model equations should be recorded with the correct exponents, so that errors in predictions other than those due to the limitations of the model itself could be avoided. They are given hereunder.

Jan 1, 1995

By K Osman, P Bennett

The mining of an underground orebody requires development both in waste and ore before stoping commences. Regardless of what metal is being extracted, the waste development is minimised to reduce the cost per unit of metal mined. At the Western Metals Zinc Kapok mine site, reducing the cost per tonne of lead and zinc mined is paramount. Decline waste development costs can be minimised by methods such as increased gradient or reduced drive size. Ore development will also involve some mining of waste. The degree to which waste mining can be minimised will depend on the thickness and dip of the orebody. The drive geometry will also determine the percentage of waste within the face. It is by mining methods such as resue mining that selective mining may be used to maximise the amount of metal mined and reduce waste dilution. Resue mining can be used around a set of selection criteria established by the mine site. These selection criteria will determine how resue mining can be applied to the mine site. Selection criteria include firing times, number of headings available, acceptance criteria for percentage lost metal, dilution and most importantly operator acceptance. The single pass or two pass resue mining method should be chosen depending on the site acceptance criteria and selection criteria. The Western Metals Zinc Kapok mine site has established a set of parameters which accept the two pass resue mining method for the mining of the ore drives. The blasting results from a single pass resue method were reviewed during more recent trials in a single heading. Through a comparison of results, the parameters allowed the decision to determine the applicability of resue mining and its current form to Kapok. This paper outlines the parameters set by the Kapok mine site, reviews these in relation to the two forms of resue mining and examines the criteria which make this mining method applicable for Western Metals Zinc.

Jan 1, 2002