Search Documents

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

Vertical flow systems (SAPS, vertical flow wetlands) are increasingly used for passive treatment of mine drainage that is net acid. Data on 30 systems in eastern US show that well designed systems typically add about 40 g/d/m2 of alkalinity to influent net acid water. If they are designed with a conservative loading rate of 25 g/d/m2 and carefully constructed, they produce net alkaline water. Alkalinity added depends on influent acidity, Fe, pH, and retention time, and ranges widely, from 7 to 484 mg/L, so this is not a useful design criterion. Some waters may benefit from retention times longer than the conventional 12 - 16 hours, but the design must be partly based on cost-benefit considerations. Systems with fine limestone added to the compost layer perform better than average, perhaps to an alkalinity generation rate of 80 g/m2/d. A variety of problems are noted in the 30 systems and others reported in the literature. Systems with high influent Fe (> ~75 mg/L, varying with pH) tend to gradually decrease in flow rate because of precipitation and settling of Fe hydroxides on top of the compost layer. Some high-Fe systems precipitate Fe in the limestone layer, suggesting inadequate compost thickness, or short-circuiting through thin spots. Systems with Al exceeding about 10 mg/L tend to plug because of Al hydroxide precipitation in the limestone layer. Flushing only removes a small part of this precipitate, but can extend life. Some systems are ineffective because of failure of the inflow system. Some systems are uneconomic because they are oversized. A continuing program of inspection and maintenance is necessary for long-term performance.

Jan 1, 2003

By R L. Chaney, M Mahoney

Mine and ore beneficiation wastes and smelter contaminated soils often cause phytotoxicity and threaten adverse environmental effects if not remediated. Science has clarified both the risks from soil metals and methods to alleviate those risks that can be applied at low cost. Phytoremediation is a family of plant and agronomy based technologies to deal with environmental aspects of sites requiring remediation. If valid risk assessment indicates that metals comprise risk, phytostabilisation may be used to alleviate that risk for most contaminated sites. In particular, Zn-Pb, Cu and Ni mine and smelter sites are readily remediated by making the soil calcareous and fertile, with added organic and metal sorbent amendments that include soil microbes to ‘revitalise’ the soil. In each case, the soil fertility and causes of phytotoxicity should be clarified by agricultural soil extractions, and the combination of amendments required to improve fertility and reverse phytotoxicity identified and found locally. In contrast with phytostabilisation, phytoextraction/phytomining uses rare metal hyperaccumulator plants and agronomic management to maximise annual phytoextraction of soil elements into plant shoots for harvest, ashing and use as a metal ore. Plants that accumulate more than two per cent Ni in shoots, and yield 10–20 t ha-1 dry biomass yield 200–400 kg Ni ha-1, which has value greater than all common agricultural crops. Considering the value of elements, existence of hyperaccumulator plants and demonstrated agronomic management for Ni phytomining, it is clear that mine sites and Ni mineralised subore-grade serpentine soils can be phytomined economically as an agricultural mining technology. A team developed agronomic methods and improved cultivars of Alyssum, which can be profitably grown on temperate zone Ni mineralised or contaminated soils. Plant species for tropical ultramafic soil materials have been identified. Phytoextraction is also strongly needed to remove Cd from rice soils to prevent human disease from soil Cd.CITATION:Chaney, R?L?and?Mahoney, M, 2014. Phytostabilisation and phytomining – principles and successes, in Proceedings Life-of-Mine 2014 , pp 3–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The introduction of many new hydraulic ally and pneumatically powered impact breakers over the past few years demonstrates the growing interest in this technique of breaking rocklike material. The most practical method yet devised to increase the blow energy range of hammer type impactors without incurring weight penalities, is to cushion the impact of the hammer on the tool. This has been achieved in one impact breaker by means of replenisible fluid cushions between the tool and the hammer, and blow energies up to 27,000 joule (20,000 ft. lbs.) have been achieved. Impact rock breaking is becoming an important alternative to the use of explosives in the mining and the construction industry. The design of impactors is discussed and manufacturers data is presented for most of the machines now available. A review of the research and mechanics of breaking rocks with impactors is presented and the benefits of high energy impactors are discussed. The relative merits of three impactor design types are explored with regard to achieving high blow energy.

Jan 1, 1978

With the burgeoning opportunities for new gold mines to be developed the opportunity now exists for a reassessment of the optimal processing path for these gold ores. Projects have traditionally followed the path of whole ore cyanidation with either Carbon In Pulp (CIP), Carbon In Leach (CIL) or Merrill Crowe. The challenge ahead is whether these traditional processing methods are the best option for stakeholders, or to go beyond CIP and use a combination of currently available technologies that can be used to provide gold recovery at a significantly reduced capital cost and minimal deleterious impact on the environment. Either stand alone or combinations of gravity concentration and flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. Treatment of a gravity/flotation concentrate by intensive cyanidation may be processed by the InLine Leach Reactor (ILR) developed by Gekko Systems of Australia. The advantages of the technology combining gravity/flotation followed by intensive cyanidation are significantly reduced capital costs; improved safety due to reduced cyanide inventories; the majority of tailings un-contaminated by cyanide; less energy required due to an opportunity for an increase in grind size û reducing green house gas emissions; detoxification of concentrate tailings can minimise tailings disposal and containment requirements.

Jan 1, 2004

By Ralph AM, Deakin JJ

A quantitative knowledge of underground mine ventilation requirements and conditions has become increasingly important, both to meet statutory requirements and to ensure high levels of safety and productivity within mines. The ACIRL Mine Ventilation System MINVENT was designed to provide a flexible means of analysing the behaviour of an underground mine ventilation system under a variety of conditions. It is not sufficient to rely solely on the analytical tools such as ventilation network analysis computer programs - these must be supported by the expertise necessary to conduct an accurate underground ventilation survey as well as experience of typical conditions to be expected in the evaluation of proposed extensions to a new or existing mine. When planning a new mine, the ventilation engineer can use the program to draw on a set of typical ventilation parameters, seam and proposed mining methods. These have been assembled as a result of numerous ventilation surveys conducted by ACIRL in New South Wales and Queensland.

Jan 1, 1983

Stope filling practice on the Great Boulder Mine was described in -a paper published in Aus.I.M.M., Proceedings No. 137, in 1945. When the paper was presented the process had emerged from the experimental stage, most of the initial operating difficulties had been overcome, and it had been established that this method of filling was suitable for the working of ore bodies in the Kalgoorlie field: Since 1945, it has fulfilled its early promise, -and during 1947, the tonnage of fill placed was sufficient to cover current operating requirements as called for by the mine ore breaking programme. The object of this paper is to outline current operations. In so doing it will refer' to some ground covered by the previous paper, but will omit details of the initial experimental work. It will include, however, a description of further experimental work on the use of hydraulic filling for worked-out shrinkage stopes, arid will provide more accurate data on costs than were available previously.ESTIMATE OF TONNAGE OF FILL REQUIRED.Early in 1946, the mine ore reserves were analysed in order to estimate the relative tonnages to be mined per four-weekly period by shrinkage stope methods -and by cut and fill stope methods respectively. This analysis was extended beyond the blocks already prepared for stoping, and inclqded the majority of the major ore blocks in the mine ore reserves. It gave the following results:-For a mill tonnage of 28,000 tons per period, 6,933 tons were required from cut and fill stopes, and a possible future maximum programme of 35,000 tons per period would require...

Jan 1, 1948

By Laros T, Schoenbrunn F

Deep paste thickeners have been proven capable of consistently producing medium to low slump material for disposal without the need for filters. However, proper design of the entire system is critical for a paste project to he successful. Some of the factors that must be carefully considered in design of a paste system include thickener sizing, tailings inipoundineni design, underflow pumping, and control system.

Jan 1, 1998

Madison Enterprises Corp. and Matu Mining are currently ex- ploring the Mt. Kare property in Papua New Guinea. The Mt. Kare gold prospect has had a short but very active history, since the first discovery of gold in the area in 1986 the property has sccn: a 3 year gold rush during which 10,000 alluvial miners re

Jan 1, 1997

The carbonatite-hosted apatite deposit at the Cajati open pit mine in the Jacupiranga igneous-carbonatite complex is located in south-eastern Brazil. The major styles of apatite mineralisation include veins or veinlets, small pods or patches, disseminated apatite and locally massive aggregates. The metallurgical concentration of the apatite is accomplished by grinding the carbonatite, removal of magnetite with a magnetic drum, size classification with cyclones and flotation to suppress carbonates and collect apatite. To examine the character of the apatite grains and to apply those observations to apatite beneficiation, specimens of carbonatite were collected from recent exposures in the mine and from selected drill holes. This study utilised a variety of microscopy methods, including transmitted and reflected light, cathodoluminescence (CL) and scanning electron microscopy with wavelength-dispersive spectrometers for mineral compositions. It was found that LREE, Na and Sr are the main elements replacing Ca in the apatite, with relatively low oxide contents (<0.5 per cent, but up to about one per cent for Sr). LREE and Sr contents consistently increase in the latest intrusions (C4, C5 and SP24). Chemical and morphological modifications of apatite were recognised to be related to detrimental effects on flotation recovery. Three examples illustrate this relationship: 1.  Apatite with reddish CL is fractured. Locally that apatite exhibits no CL due to CL quenching caused by iron entering the apatite structure.2.  Apatite from the xenolith-rich area exhibits abundant fine, platy silicates that appear to interfere with flotation and lower apatite recovery.3.  So called æhardÆ apatite, which is more difficult to grind, occurs in an area in the mine that was affected by hydrothermal activity. That activity is evidenced by the development of a bright, white CL rim in the apatite, and by the presence of late veins of carbonates and sulfides that fill fractures and appear to contribute to higher cohesiveness of those apatite grains.

Jan 1, 2008

By M DellÆAmico, K Vining

The iron blast furnace is the most widely used and efficient producer of liquid iron; however, emissions from sintering and coking cause environmental pressure for the integrated steel works. The combustion of coke fines (breeze) during sintering contributes to greenhouse gases (GHG) (eg carbon dioxide) and is a source of SOx and NOx emissions. Coking capacity is also constrained by environmental concerns and economic factors, such as increased coke consumption, and short supply is leading to high prices. Improved coking practices, which result in reduced production of fines, are also contributing to the tight availability of breeze for sintering. This combination of factors presents an opportunity to consider alternatives to coke as a fuel for sintering. CSIRO Minerals has been investigating the use of wood biomass/char as a substitute for coke during sintering. Wood biomass, or char produced from it, is an attractive carbon source as carbon dioxide liberated during combustion can be sequestered back into growing biomass. It has great potential to reduce the emissions from integrated steelworks and improve their environmental acceptability. Harvested biomass/char is also a renewable and sustainable resource and can be integrated with good land management practices such as remediation of salinity affected land. Weeds, especially woody weeds, can also be used as a source of biomass for charcoal, and integrating char production with weed management can help address a pressing environmental issue in Australia. Previous reported preliminary testwork indicated that the use of Red Gum char as a replacement for coke resulted in a product sinter of comparable quality, improvements in productivity and significant reductions in SOx and NOx emissions. In the latest testwork, CSIRO has examined the properties of a range of potential charcoals, and has conducted a further series of granulation and small-scale sintering trials with them in simulated Japanese Steel Mill iron ore blends. Sinter fuels characterised and evaluated include industry sourced coke breeze, commercially available wood char and a charcoal from prickly acacia (acacia nilotica). Prickly acacia has been declared a noxious weed, is widespread in Australia, and is classified as a æWeed of National SignificanceÆ. The results presented in this paper support the notion that charcoal outperforms coke in many aspects of iron ore sintering and factoring in environmental considerations makes the switch to charcoal even more favourable.

Jan 1, 2005

This paper presents an overview of the current status of mine water management in South Africa. The regulatory framework within which mine water management operates is set out, based on the principles and policies embodied in the relevant legislation. The status of the gold and coal mining industries, with regard to water management, is presented on the basis of studies that have been undertaken to develop water and salt balances for these industries. While the data is not available to quantify the status of ARD in South Africa, the range of typical mine water quality problems faced by South African gold and coal mines is presented. The status quo, problems and challenges relating to mine water management are presented and discussed. It is shown that, while there have been major strides in the last decade, and mine water management and treatment in South Africa has moved onto the forefront of mine environmental management, important problems still persist. There is still a significant amount of improvement required, particularly in the field of prediction of water quality deterioration and the application of such predictions to the identification of management actions that can be applied to prevent or minimise mine water pollution in the shortmedium- and long-term.

Jan 1, 2003

By D J. Williams, S Islam

Fine-grained coal tailings slurry undergoes only limited settling and self-weight consolidation, and tends to remain slurry-like and unsuitable for conventional laboratory consolidation testing. In addition, constant rate of loading consolidation testing is more representative of the continuous disposal of tailings slurry into a tailings storage facility (TSF) than conventional step loading. The laboratory consolidation testing of coal tailings slurry under a constant rate of loading has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. In the slurry consolidometer, the rate of loading may be varied to represent the actual rate of rise of the tailings in the TSF. A slow rate of loading increases the test duration, while too fast a rate of loading may build up very high excess PWP, without achieving significant consolidation. For the particular fine-grained coal tailings slurry tested, the rate of loading in the slurry consolidometer is varied to access its effect on the development and dissipation of excess PWP. The resulting consolidation parameters are evaluated and explained using the recorded settlement and PWP data.CITATION:Islam, S and Williams, D J, 2018. Optimisation of constant rate of loading slurry consolidometer testing of fine-grained coal tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 72–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D Matthews

With the increasing demand for quality-specific ores, coupled to the reality of even more complex minable iron ore reserves, there is a growing need for real-time online material analysis of plant feed and product. For a full system mass balance, the combination of conveyor weight scales, flow and density transmitters are required. This alone does not guarantee product grade. For optimal process control and material blending, real-time online elemental scans in combination with the mass weighting is becoming more than a ‘nice to have’. These elemental scans located at key positions, enable the mining and plant operators to make informed decisions timeously, therefore ensuring product outcomes and optimising operations where material grade and the control thereof are important. Typically, these units follow the mining and primary crushing circuit as well as on the product conveyors, low-grade conveyors and tailings lines. Deployed after the primary crushing circuit, an analyser acts twofold:1. guaranteeing mining production, and2. processing facility feed blends.The analysers on the product conveyors guarantee saleable product. The analysers on the low-grade conveyor and tailings line complete the elemental balance and identify the potential of the low-grade and tailings for future processing. The system losses (accumulation) are calculated to determine the amount of material ‘lost’ during the processing stage which does not report to any of the aforementioned and can be used as a measure of the efficiency of the plant. A further advantage of the real-time online analysis of material is that immediate intervention can be taken in the event that the product is not of saleable product grade requirements. In the Khumani Iron Ore mine, Northern Cape, South Africa, run-of-mine (ROM), product and control analysers were included. Run-of-mine and product stockpiles are certifi ed, low-grade material is not currently directly measured, but calculated from the internal control loops. Iron units are reconciled between product and feed material.

Jul 11, 2011

The design and selection of components for belt conveyors is a well known procedure and many handbooks, catalogues and design manuals offer a wide range of detailed information which can be applied to most of the known conveyor problems. The aim of this paper, however, is to investigate the various methods of conveyor drive configurations, and incorporate the latest technical achievements in the control systems, particularly for high capacity conveyor systems carrying ore from pit to processing plants where the lowest maintenance, operating and initial costs are of major importance. Past experience has proven that multi pulley drives can reduce initial capital cost of a conveyor; this leads to the need for better torque control during startup, running, stopping and load sharing. Many methods of torque control are available and have been used in the past. All types have their advantages and disadvantages and must be considered when designing a conveyor or conveyor system. However the recently developed solid state electronic soft start controls utilising AC squirrel cage induction motors are gaining acceptance, especially for a conveyor system where the same control and logic system can be used to transmit startup commands to more than one

Jan 1, 1978

By S J. Neethling and, S J. R Simons

In this paper the effect of humic substances (natural surfactants), electrolytes and solid particles on bubble coalescence, and as a consequence on froth stability, have been investigated. In this study two bubbles of equal size were formed and forced to collide using a novel experimental apparatus. The interactions were recorded by a high-speed camera, the images of which helped to determine the coalescence frequency and the coalescence time, as well as the mechanisms of the interactions. Two types of humic substances were used, along with three different electrolytes. Humic substances appeared to have a considerable effect on bubble coalescence, while the effect of electrolytes was minimal. Moderate and high hydrophobic glass spheres were used between two bubbles. Very hydrophobic spheres promoted fast bubble coalescence, while moderate hydrophobic spheres had no effect. Data of coalescence frequency and time is presented, as well as images of the coalescence events. The coalescence frequency was used to validate a parameter, Pf, known as the film failure frequency, used in a simulation model to predict foam height in a gas-sparged vessel. Predictions determined using Pf were then validated by experimentation.

Jan 1, 2005

Operating metallurgists spend a significant part of their time running plant trials to compare two or more conditions in order to improve the process, such as a new reagent, flow sheet or piece of equipment. The best way to conduct such a trial is as a paired experiment when testing two conditions (eg 'old' and 'new') or a randomised block design when testing more than two conditions. These experimental designs should always be preferred over alternatives if their requirements can be met, because they block the effect of uncontrolled variables ('covariates') and are the most statistically efficient, ie they will lead to the required level of confidence in the outcome faster than other methods. Sometimes, however, it is not possible to switch condition easily, which is a prime requirement of these methods. In such cases the only option may be to switch condition once only, and compare the process performance before and after the switch. Examples are testing grinding media, large equipment, or long residence time processes such as leach trains or CCD thickeners. This paper considers some data analysis methods to deal with this situation. Modelling with intervention analysis (IA) uses regression models with a dummy variable to indicate the presence or absence of the test condition. IA with a time series model ensures that the residuals are uncorrelated. IA with a process model helps to deal with the problem of covariates. The reference distribution is a method free of any statistical assumptions but is less powerful than the other methods. Cusum charts are a helpful visual aid to interpreting time trends. A combination of these methods can help improve the confidence in the final decision. None are as good as a formal experimental design such as a paired trial.

Jan 1, 2008

By Simpson JF, Murrie SJ

In determining new areas for slag disposal a foamed slag aggregate has been developed for use as a skid resistant material. The foaming of the slag does not rely on the use of water, but rather on the slag chemistry. Laboratory test results indicated that a product having good skid resistant properties has been prod- uced. A section of road is being assessed for performance of the aggregate in a surface dressing application under heavy load. The results from the test section after seven months have shown that the foamed slag is suitable for this application. Further test sections are now being considered.

Jan 1, 1979

Thank you chairman, good afternoon ladies and gentlemen. In my talk this afternoon I intend to cover a brief history, some of the recent experiences and an overview of the McArthur River project.If we consider the themes of this forum, Obstacles and Opportunities, I can confidently say that in attempting to develop the McArthur River deposit Mount Isa Mines Limited (MIM) must have encountered almost every obstacle that can be imagined. However the large size and the high grade of the deposit has ensured an opportunity, from which it is very difficult to walk away from.The McArthur River Here's Your Chance (HYC) Deposit is located in the Northern Territory of Australia. It was discovered by Mount Isa Mines Limited geologists in 1955 and is one of the largest known sedimentary stratiform zinc-lead-silver deposits. The deposit has been the subject of numerous investigations and considerable expenditure culminating in a major feasibility study in 1979. There were a number of factors which prevented development, these being the size of the project, the fine grained mineralization, geographical location, market, social and capital cost. The latter had been estimated in the 1979 study to be $800 million at that time.

Jan 1, 1993