Search Documents

By Edwards A. B

Re-opening of the old Proprietary mine has provided new exposures of the system of uralite dolerite dykes observed in 19110 by the Geological Sub-Committee of the Scientific Society of Broken Hill. The newly exposed dykes have been invaded and replaced by the massive ore, with development of manganese garnet and biotite adjacent to the sulphides. A similarly altered dyke in massive ore has been encountered in the North Broken Hill mine.The textures of the unaltered portions of these dykes indicate that they have not been affected by the intense regional metamorphism that has recrystallized the other rocks of the area. Moreover, in mineral composition and textures, in chemical composition, and in cross-cutting relations, they are so similar to the uralite dolerites of the district which post-date the folding and metamorphism of the Broken Hill area, that they must be regarded as typical members of this suite of post-metamorphic dykes.The invasion and replacement of the dykes by the massive sulphide ore, and their metasomatic alteration adjacent to the invading sulphides, establishes that the lode was formed after the dykes were intruded, so that the high temperature features of the ore cannot be attributed to metamorphism and recrystallization, but are primary features of high temperature hydrothermal deposition.INTRODUCTIONTwo cross dykes are recorded on the plan of the 300-ft. level of the Broken Hill lode accompanying the report on the geology of the Broken Hill lode published by the Geological Sub-Committee of the former Scientific Society of Broken Hill (1910). One dyke occurs in Block 12, and the other in Block 13, and both were stated to consist of a dark basic amphibole rock, called diorite for convenience. The more southerly dyke was traced from some distance out in the footwall, and even through the lode, by means of occasionalpatches of it still existing in the ore, in a direction...

Jan 1, 1956

By G D. Richmond, J C. Chomley

Copper has been mined intermittently at Gunpowder, north of Mount Isa, since 1927. Most ventures have had some initial success but fluctuating copper prices, the small-scale of the operations and the remoteness of the site led to closures or sale. Processing routes have included direct sale of high grade ore, flotation of oxide and sulphide concentrate, and copper cement production from mine solutions. Copper cathode has been produced by heap and in-place leaching coupled with solvent extraction and electrowinning (SX/EW). Aberfoyle Limited recently purchased the Gunpowder operation and is expanding operations. An innovative high recovery tank leaching process, including a low temperature, low pressure autoclave, has been adopted. Copper cathode will be produced from an expanded solvent extraction/electrowinning plant at approximately 45 000 tonnes per year. The combination of expanded throughput and high metal recoveries will make Gunpowder a cost competitive producer.

Jan 1, 1998

By Nekitel S, Arumba J, Kopi G, Findlay RH

The Kainantu area lies within the composite Scrapland terrane which is composed of Mesozoic metamorphic and intrusive units, overlain by Cenozoic marine sediments, volcanic and intrus-ive units and Quaternary fluvial sedi-ments.Four deformations (Dl, D2, D3, D4) are recognised within the Mesozoic sequences, which consist of greenschist to amphibolite facies schist derived from felsic to intermediate pyroclastic rocks and pelitic sediments. The second, third and fourth fold events are present in the Cenozoic sequence, and these rocks are broken by thrusts related to northwest trending D3 folds. South-dipping, possibly lystric, normal faults are recognised and may be related to uplift and exposure of the metamorphic rocks as core complexes.Known mineralisation in the area consists of gold and copper skarn deposits, porphyry copper deposits, shear-hosted gold deposits, epithermal vein deposits and gold placer deposits. Over 35 hard rock and 18 gold placer deposits are known within the area. Of significance are the Kathnell shear-hosted auriferous quartz veins; such structurally controlled veins may be more widespread than proposed prev-iously and offer a new exploration target.

Jan 1, 1994

Process engineering principles are used to analyse the features of leaching processes for large masses of low grade, unprocessed ore. Different performance characteristics are related to the numerous variants of these processes. The variant for which reagent enters a heap only via the input solution is further subdivided into three modes of operation. The three modes may occur in testwork and full-scale operations; the effects of process variables on the rate of the process are completely different in each mode. The mode can be identified by the time at which reagent first appears in the pregnant solution. It is related to the ratio of the height of the heap and the thickness of a band of ore in which the reactions are localised. Synthesis of the phenomena occurring within a heap via a computer program has produced a quantitative relation for the reaction band thickness. The program has been validated for several different systems. The overall achievement is that the mode of operation and the rate of the process can be forecast before column testwork is commenced. Some applications of the outcomes to testwork, process design and operational tactics are described.

Jan 1, 1994

By T Hicks

Designers of mining facilities play a significant role in defining the overall mine greenhouse gas emissions performance. This demands an appreciation of all the greenhouse gas emissions sources, including Scope 3 emissions, which will form an increasing fraction of the emissions as we transition our generation sources to renewable energy. Traditionally overland conveyors are designed to operate as fast as practical, and through this approach, achieve relative minimisation of: conveyor belt tensions; belt width; mechanical equipment masses; structural steel quantities; and concrete quantities. It is well understood that higher belt speeds reduce capital cost and improve project economics. Operating at higher speeds introduces operating costs through system energy losses and increased wear rates. This paper assesses the life cycle greenhouse gas emissions for a typical iron ore overland conveyor to demonstrate how the design criteria and engineering decisions impact greenhouse gas emissions and project economics. An analysis of the decarbonisation potential and project economics using a range of operational parameters has been completed, developing a marginal abatement cost for each system configuration, creating a basis for integration of low emission overland conveyor designs as part of the broader facility decarbonisation strategy.

Sep 1, 2024

By Griffiths L, Marshall P

fhis paper describes investigations into drainage of gas from the solid to control outbursts. Initial studies conducted on drainage of shear zones showed that, given enough time, these can be successfully drained. Once drained, they can be intersected and driven through without any activity of outbursts. The results of programme of investigations to determine parameters for drainage from the solid show that gas flow rates from the Bulli Seam on the average are about 2 litres/min/metre length of borehole. But when shear zones are intersected, the flow rates could be as high as 8 litres/min/ metre length of hole. Shear zones can be picked up from pressure measurements 50 - 60 m away and this could give sufficient time to drill through these zones and drain them in advance. Systematic drainage of Bulli Seam at West Cliff Colliery could eliminate or reduce frequency of outbursts considerably. At present drainage holes are being drilled systematically in the seam, with drainage installations on the surface. Gas purity of 80% methane is being delivered at the surface plant.

Jan 1, 1980

Cyanide-extractable gold is far more meaningful in the definition of ore, and control of extraction, than fire- assayable or aqua regia digestible gold. The use of cyanide- extractable gold addresses the significant problems of over- as well as under-assaying by fire and aqua regia digests. The problems of conventional control or diagnostic cyanidation extractions: lengthy extraction, and masking by pregrobbing in cyanidation extractions for assay purposes; are surmounted with a novel activator - Leach WELL. Full extraction of liberated gold, insignificantly affected by preg-robbers, can now be achieved within 30 minutes. This can assist in reducing common gold losses presently often hidden by inappropriate mine call factors, and/or high grade cut values. This paper includes a discussion of fundamental mechanisms of cyanidation, preg- and assay-robbing, which underlie the phenomena Involved.

Jan 1, 1992

Deposits of chromite are in associated with ophiolite complexes in Papua New Guinea. No deposits which are currently exploitable have been recognised, but large resources that may be economic in the future are present at Ramu area and on the Morobe coast. These are contained either in laterites or in sediments derived from ultramafic members of the ophiolites. There are possibilities of establishing further resources either in similar settings or associated with ultramafic members of alkali intrusive Complexes.

Jan 1, 1987

The Australian Mineral Industry's growth in the last two decades is directly related to the skill and experience of its consultants in mining, metallurgy, geology, finance, management, marketing, and engineering. The role of mining consultants needs to be re-examined, so that the quality of the service they deliver will continue to be adequate for the 1990's. One means of this evaluation is by examining Case Studies in the strategies and difficulties of developing contract and entrepreneurial research.

Jan 1, 1986

By Carlini G, Ibba R

The KSS Lead Plant (Kivcet - SNAMPROGETTI - SAMIM) of Por tovesme, owned by Nuova Samim (the sector-head Company for non ferrous metals and derivatives owned by ENI), has been operating since february 1987. This plant is based on the Soviet Kivcet licence and testwork carried out on the pilot plant of VNIITSVETMET in Ust Kameno gorsk fed by the Nuova Samim's concentrates. The plant is com pletely automatized using the most advanced technologies and it is operated by nineteen people on shift work, including all ancillary units and lead decopperizing-casting. The expected performance of the plant has been confirmed and improves day by day in relation of the operating experience, thanks to the new conceptual design of the furnace. Due to the remarkable flexi bility of the process, the integration of the lead plant with the other plants of the metallurgical complex of Portovesme rro-#4 (Electrolytic Zinc Plant, Sulphuric Acid Plant, Imperial Smel ting) has shown all the economic advantages. The lead content in the ambient air, detected by the monitors, either in the working area and on the ground outside the complex, is widely Pb W" below the stricter new limits recommanded by the E.E.C. (Economic European Community) rules and by the Italian law. The whole process is carried out in equipment completely closed and under suction and it does not require manual operations with exposure to the lead. The production cost is much lower than that performed by the traditional technology. This advantage permits wide margin to consider investment to replace the traditional technology.

Jan 1, 1989

By Resta S. A

Energy Resources of Australia Ltd - Ranger Mine is located about 255 kilometres east of Darwin in the Alligator Rivers Region of the Northern Territory. The Ranger project is surrounded by Kakadu National Park which is on the UNESCO World Heritage list. . Ranger Mine operates the largest uranium mine and processing plant in Australia. It is designed to produce 3000 tonnes of uranium oxide per year, but presently is producing a little less than one half that figure due to the depressed uranium market. The safety performance of the employees and Ranger as a whole continues to improve. The lost time injuries (LTI) have significantly reduced from 74 in 1985 to five in 1994. The total days lost due to LTIs have gone from 1543 to 14. These significant improvements have reflected directly on workers' compensation premiums in which a four-fold reduction has occurred. It is estimated that the actual monetary saving to the company is about $1.3 million per year and directly reports to the profit of the company. There is also an obvious and significant reduction in the less quantifiable costs such as the suffering of the injured employees and cost to society. The paper will review the various initiatives introduced and assess their effectiveness. Performance improvement is primarily dependent on the commitment, introduction of various initiatives and the subsequent change in workplace culture.

Jan 1, 1994

By Lemberg D. W, Friday R. G

Potential means of lowering overall costs to permit deeper stripping include : 1. the use of larger diameter blastholes in highly-fissured strata (to reduce drilling costs); 2. dewatering from semi-permanent bores to reduce blasting costs (by maximising the use of bulk ANFO) and promote highwall stability; and 3. the use of inclined blastholes, bulk AN, staggered V1 patterns, adequate backfill and more cost-effective stemming columns. Each of these is covered. The pumping of bulk watergels continuously raises the blasthole water column, thereby perpetuating the demand for these blasting agents. This must be a principal consideration when choosing between a bulk and a packaged watergel. Any packaged product should exhibit dimensional permanence and an energy yield per metre length equal to that of bulk ANFO. Possible ways in which controlled trajectory blasting (CTB) could benefit deeper stripping operations are outlined. By allowing the maximum use of bulk ANFO, de- watering may be a prerequisite of a viable CTB Operation.

Jan 1, 1981

By M Hilden, K Barbosa, M Yahyaei, C Ndimande, K Runge, V Jokovic

Classification devices provide a link between comminution and flotation. Basically, it determines which particles are diverted back for additional grinding and which ones pass to downstream flotation. Therefore, the classifiers play an important role in the performance of a mineral processing circuit. Hydrocyclones are the most common classifiers used in wet grinding, despite being associated with poor classification efficiency. Hydrocyclones are widely used due to advantages related to low maintenance as well as reduced capital and operating cost. Other classifiers, such as fine screens, have much better classification efficiency compared to hydrocyclones. The major challenge of using screens in an operation, however, is their large footprint and increased maintenance requirements relative to hydrocyclones. Some researchers have demonstrated that switching from hydrocyclones to screens, as the classifier device in a ball milling circuit, resulted in a 20 per cent increase in plant throughput and significant improvements in coarse particle recovery, resulting in a 6 per cent increase in overall flotation recovery. However, it is known that these benefits of improved classification are very much ore specific, ie depending on the ore response. Therefore, there is a need to estimate the benefits of improved classification in pilot scale testing before the plant could consider the potential classifier upgrade. This paper presents the results of two pilot-scale grinding tests where the ore sample was processed using different classifiers: a traditional hydrocyclone and hybrid classification involving the use of a semi-inverted hydrocyclone followed by a screen. The size specific energy and circulating load were used to compare the performance of the grinding circuit. The grinding product was subject to mineral liberation analysis and the impact of classification efficiency on the mineral liberation is discussed in the paper.

Aug 24, 2022

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By D MacKenzie

The Rise & Shine Shear Zone is a shallow-dipping Cretaceous late metamorphic shear zone formed in a compressional environment. The Shotover mineralised system is dominated by normal faults with well-defined vein systems that cut across Miocene schist folds and faults related to the inception of the Alpine Fault. Despite the geological differences between these mineralisation systems, they share many common features of hydrothermal alteration that have resulted in disseminated gold in altered sheared schist. The most distinctive feature of both systems is the abundant ankeritic carbonate that has formed from decomposition of metamorphic chlorite. Excess iron from this alteration reaction combined with hydrothermal sulphur to form sulphides that host the disseminated gold. The chlorite decomposition reaction was reversed in the latter stages of both mineralisation systems, and this was accompanied by further gold emplacement in the Rise & Shine system.   Both alteration systems involved initial decomposition of metamorphic albite, followed by deposition of albite as a vein mineral in the latter stages. The fluid flow that yielded the disseminated gold was controlled by microshears that pervade host schists, in strong contrast to many Otago Schist vein systems where host rock alteration is absent. The ankeritic alteration in the Shotover and Rise & Shine mineralised systems has increased the volume of mineralised rock, and may have made suitable targets for large-tonnage, low grade gold deposits.

Jan 1, 2007

By C Katonga

Mindola mine is currently the deepest mine in the Zambian copper belt. Stoping is currently active to 1330 m below surface with long range plans indicating future production from 1590 m level. The orebody is tabular and dips between 55o to vertical. The thickness varies from 8 to 14 m. The vertical crater retreat method of mining was first introduced at Mindola mine in the late-1980s following several trials that helped define the design criteria for its application. Over the last ten years the method has been continually modified to improve safety and maximise ore production. For example, due to the weakness of some rock units within the orebody formation and the instability of the hanging wall, the last VCR slices are usually between 8 - 10 m thick, and efforts are being made to strictly apply shrinkage method in order to reduce dilution. Recent advances in mining technology in the areas of equipment, blasting techniques, rock mechanics and materials handling have been employed to increase the overall productivity of the mine. Large down-the-hole machines capable of drilling 165 mm diameter blast holes, up to 80 m long are used in stoping. Each stope produces up to 20 000 tonnes of ore per month and can last for three months. Heavy systematic ground support of VCR development has significantly enhanced safety for mining crews and equipment. Crater mining has not only improved productivity and enhanced safety, but also overcome various problems associated with conventional sublevel open stoping previously employed at the mine. This paper discusses the technical and operational aspects of vertical crater retreat mining at Mindola mine during the last ten years. The changes in mining method are often accompanied by changes in mine design, blast design, mining equipment, ground support and operating practices.

Jan 1, 2000

By M Salu, G J. Kay

"As underground mines increasingly face the challenge of maximising production without losingfocus on safety excellence, the ability to predict the eff ectiveness of mine seals and stoppings andthe identifi cation of defects plays an increasingly important role in mine ventilation management.While technologies for sample testing installed seals provides signifi cant assurance, the difficulty of conducting tests in operational environments, combined with the production impact of destructive testing procedures, has led to the development of a new method for non-destructively testing ventilation control devices (VCDs). This paper addresses the challenges of in situ testing and reviews the approaches previously employed to verify the quality of VCD installations. It then describes a new testing methodology jointly developed by Whitfield Minerals PTY Ltd and Parsons Brinckerhoff (PB) and the range of tests that have been carried out in the laboratory, above ground, at trial underground sites and in active coal mine operations. Although this is a new approach to testing underground VCDs, the method employs recognised testing equipment in a new application. The aim of the new non-destructive technology is to not only verify the thicknessand therefore overpressure rating compliance, of new VCDs, but to allow mine operations t oidentify and locate defects in installed VCDs without causing damage to the material structure.Currently it is difficult, time-consuming and costly to carry out physical sampling and testing ofevery VCD. Therefore, a reliable and accurate means of non-destructively testing concrete andplaster seals in situ will provide substantial operational and safety benefi ts to the underground coal mining industry."

Jun 1, 2012

Nine case studies are presented to illustrate how risks can be, minimised or quantified during pit optimisation, utilising Whittle Four-D software. Each case study covers a specific problem that has been encountered from a wide variety of pit optimisations. Case A: Maximising profits when the tenement owner is paid a royalty on tonnes processed. Case B: Allocating product prices, rather than a single commodity price during optimisation. Case C: Quantifying processing costs that are affected by penalty elements in the ore. Case D: Exploration expenditures below current pits can be quantified through the use of simulation techniques. Case E: Alternative strategies can be quantified when pits are restricted by tenement boundaries. Case F: Relocation of mine infrastructure that requires large capital expenditures, can be simulated by allocating costs to an area during optimisation. Case G: Evaluating alternative corporate strategies during pit optimisation. Case H: Sensitivity analysis for price, processing cost and mining cost. Case I: Quantifying the advantages of using additional mining capacity during the early periods of mining.

Jan 1, 1994

Successful evaluation and exploitation of resources and reserves relies on the collection of high quality sample data. The quality of the sample data must be maintained through the application of a robust quality assurance and quality control (QAQC) program, including documentation of sampling procedures, training of sampling personnel and the regular monitoring of control samples. However, the application of QAQC programs in the minerals industry is often poor and the purpose misunderstood. It is all too common to have good quality control data collected, but no analysis work carried out until after drilling is completed. In a lengthy drill program, this can lead to problems not being discovered and corrected as they happen. Moreover, rectifying problems afterwards will be costly in terms of time and money, if not impossible. The consequences of poor quality sample data are many and include such effects as over- or underestimation of block grades, misclassification of ore and waste, and lower confidence in the resource/reserve models. The purpose of this paper is to highlight, using case studies, the importance of good QAQC practices to monitor the quality of sampling and laboratory sample preparation and analysis.

Mar 1, 2010

By Mitchell I, Gelfi P, Dunne R, Pyper R

Dump leaching at Teller in its present form began in the fourth quarter of 1988 as an adjunct to milling operations. Initial plans called for a dedicated dump leach facility capable of processing ore at an annual rate of 2.0 million tonnes. Construction of a dump leach pad, collection and process ponds, carbon adsorption system, elution plant as well as reagent addition and ancillary facilities was initiated in mid-1988. During the course of construction, additional reserves were proven. As a result, design throughput was increased to 4.0 Mtpa. Leach pad capacity and solution supply systems were upgraded to handle the larger throughput. However, the carbon adsorption/elution facilities were not upgraded due to space limitations. During 1990 it was decided to expand the dump leach operation to 6.0 Mtpa. Construction of a second leach pad was required which was initiated in early-1991. Plans were again upgraded prior to completion to a target annual throughput of 10.0 million tonnes was. A further two leach pads have been constructed. The first of these being completed during the latter part of 1992. Construction of the latest and largest pad commenced early in 1994.

Jan 1, 1994