Search Documents

By X Feng, X Zhang, W Sun, Y Zhe, K Hou, B Zhao, H Liu

Pulang Copper Mine, being China's largest newly built mine using block caving, boasts an annual production capacity of 12.5 million tons. Production level and roadway stability hold the key to the successful application of block caving. However, with Tong Kuangyu being the only mine in China which has applied such a method, we currently lack relevant experience in the successful application of the method. This paper has studied the influence of different rock mass zonings, fault thickness, fault dip angles, on-site construction quality on the production level, roadway stability of block caving through numerical simulation and analysed the roadway stability in different kinds of support solutions so as to ensure the successful application of block caving in Pulang Copper Mine. The results have shown that the existing support method in Pulang Copper Mine can meet the requirement of roadway support in zone II and III, but could not satisfy the demand in terms of support strength in the relatively fragmented zone I area. When roadway passes through the fault, the deformation of surrounding rock and plastic zone of roadway will gradually decrease with the increase of fault dip angle; the deformation of surrounding rock and plastic zone of roadway will gradually increase with the increase of fault thickness. An ideal support effect can be achieved through the joint support of grouting and bolting when roadway passes through the fault. In the measured model of on-site construction, there is stress concentration in the intersection between the access and transverse drift of ore removal. Therefore, the stability of the roadway can be improved by improving the construction quality. CITATION:Sun, W, Hou, K, Zhang, X, Feng, X, Liu, H, Zhe, Y and Zhao, B, 2018. Research on supporting technology for production level roadways of block caving in Pulang Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 95–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M G. Millad, M Zammit

The Kipoi Central (KPC) copper project is located in the Katanga Province in the Democratic Republic of the Congo and is presented here as an example of an operating mine where the Mineral Resource was initially estimated by uniform conditioning (UC) and subsequently updated to localised uniform conditioning (LUC). This paper discusses the implementation of an estimate run using LUC and compares the results based on resource definition drilling to those obtained by close spaced grade control drilling and actual mill production.UC is a nonlinear geostatistical technique designed for recoverable resource estimation, typically using wide spaced exploration and resource definition drilling. The primary output of UC is the grade, tonnage and metal above a series of user-defined cut-off grades for a particular selective mining unit (SMU) block size. The UC approach is considered to provide a more accurate representation of the recoverable grade and tonnage at SMU support for non-zero grade cut-offs than would typically be achieved by a traditional linear estimator such as Ordinary Kriging. LUC is a relatively new approach involving the post-processing of a UC estimate and is used to spatially present the grade distribution predicted by UC at the SMU scale.This study demonstrates that the calculation of a more accurate and realistic grade-tonnage relationship for small SMU sized blocks is possible at the exploration stage using LUC, provided that the necessary theoretical and practical conditions for implementation of this technique exist.CITATION:Millad, M G and Zammit, M, 2014. Implementation of localised uniform conditioning for recoverable resource estimation at the Kipoi Copper Project, Democratic Republic of the Congo, in Proceedings Ninth International Mining Geology Conference 2014 , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By W F. E Ouedraogo

This study data has been collected on a three-month period from November 2020 to January 2021 and based on three different pits: Vindaloo Main, Vindaloo Central and Bouere. Both pits having specific geotechnical and geological properties. Vindaloo Main, VIM, and Central, VIC, have the same mineral composition as volcanic tuff with felsic intrusion or monzodiorite, both rock mass is fractured with small joint. Geotechnically the uniaxial compressive strength UCS between 200 to 300 Mpa, Young’s Modulus 110 Gpa and Poisson’s ratio between 0.1 to 0.2. Bouere pit is basically made of volcanic tuff stock works as intrusive, UCS between 200 to 300 Mpa, Young’s Modulus 103 Gpa and Poisson’s ratio between 0.2 to 0.3. The first step of this study was to collect various data from mining operations around the drilling and blasting inputs. This was based around the different scenario of drilling parameters and the outcomes on the blasting, and how they impact load and haul operations and productivities of excavators from the heave to the last flitch. In most cases surface photos of the blast do not represent the overall fragmentation in the blast volume. Photos of the different flitches will not show only the effect of blast, as the loading operation generating more fragmentation by applying weight on the muck pile. Then the record of the different material uses for feeding. The last part of the analysis is the physical data from process plant such as particle size, throughput rate, both for the crusher and the mill, per pit and material and the specific Bond Work index (BWI). Fine particle quantity production is also a key point as is one direct indicator of milling performance. In overall, making link to BWI can influence at each stage of the mining to the processing operation. Drill and blast constitute a high cost in hard rock mining and trying to reduce these costs without an overview of all the integrated processes and context could end up by cost relocating to other activities in the process. However, the cost associated to size reduction builds exponentially as the particle size becomes smaller.

Jun 22, 2022

By Yamada K, Abe H

Magnetic scanning type mass spectrometers have been given improved sensitivity with a large dynamic range and considerable resolution by the addition of a computer-controlled electric equipment. A mass spectrometer equipped with this newly developed electric system was applied to studies of the activities of liquid iron-silicon alloys and of liquid iron-phosphorus alloys at 1600¦C. The range of silicon concentration was 5.8at%-51.1 Si= at%, and values of ySi -3.1+0.15 and es 11.5 +1.5 were obtained. The concentration range of phosphorus was 1.3at%-5.7at% and a value of eP=7.3+0.1 was obtained.

Jan 1, 1980

By M Barden, G Lane, B Quilliam

NQ Minerals PLC, through Hellyer Gold Mines Pty Ltd, plans to reprocess the contents of the Hellyer tailings dam to produce lead/silver concentrate, zinc concentrate and pyrite concentrate (containing Au and Ag). This paper discusses the project development, mineralogy, metallurgy and chemistry of processing Hellyer tailings and the associated environmental benefits. The Hellyer and Fossey orebodies were volcanic hosted polymetallic massive sulphide deposits located within the Mount Read volcanic arc of western Tasmania. Mineralisation was hosted in massive sulphide (pyrite) and comprised predominantly of sphalerite, with lesser galena, chalcopyrite and arsenopyrite. The Hellyer orebody was mineralogically complex (fine grained) and was treated through differential flotation with initially modest recoveries. Fossey ore processing characteristics were similar to those of Que River ore and simpler than Hellyer but treatment still resulted in significant grades in flotation tailings. CITATION: Lane, G, Barden, M and Quilliam, B, 2018. Hellyer tailings – complex mineralogy but higher grade than many ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 35–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By N Maistry, C Carelse, A Singh

Banded Iron Formations or more commonly known as BIF are sedimentary rock formations with alternating silica-rich layers and iron-rich layers that are mainly composed of iron oxides (hematite and magnetite), iron-rich carbonates, and/or iron-rich silicates. Considering the depletion of highgrade iron ore reserves in South Africa, there is a need to maximise resource utilisation through the exploitation of low-grade/uneconomic resources particularly BIF material, which makes up more than 65 per cent of current reserves. Previous test work conducted by alternative BIF sources globally indicates the need for fines processing in order to produce a concentrate. South African BIF however is amenable to coarse and fines processing producing an on-grade product or blended feedstock. C-Type material within South Africa’s Northern Cape Province grading at approximately 33 per cent Fe was supplied for research purposes. Top size optimisation via gravity Heavy Liquid Separation (HLS) tests was conducted. The laboratory results being perfect separation (Ep=0) were modelled to predict pilot performance, the results of which were tested on a pilot scale for the finest size fraction (-1 mm). It was observed that a top size of -2 mm provided optimum results in terms of upgrade and recovery, with crushing finer not necessarily producing superior results. At a target grade of 60 per cent Fe, recoveries of 65.6 per cent were achieved on the laboratory scale, whilst recoveries of approximately 58 per cent were achieved on the pilot scale. Targeting higher upgrades of 63 per cent would inevitably result in lower recoveries of 57.2 per cent on a laboratory scale and approximately 54 per cent on a pilot scale. This is in line with grades and recoveries achieved globally for BIF material albeit at finer grind sizes.

Sep 18, 2023

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

On Monday, October 25th, 1971 at approximately 12.15 a.m. the night shift proceeding underground discovered smoke at No.1 and No-3 cut throughs on the eastern side of the belt heading and in close proximity to the upcast shaft. Attempts to control the fire continued throughout the morning; as the position underground altered various procedures were adopted in an effort to contain and control the fire. Despite these efforts at approx. 12.40 p.m. a sudden change occurred which made it necessary to withdraw all workmen from underground, the vicinity of the Tunnel entrances and upcast shaft. Sealing of the mine at the entrances was the only remaining alternative. Several boreholes were put down to enable sampling of the atmosphere and air temperatures to be taken. This was essential as a guide to determining when conditions were suitable to allow exploration of the area using mine rescue self contained breathing apparatus.

Jan 1, 1972

By Slater R

The initial planning and detail design phase leading to the development of a 7.5 m internal shaft to service the deep 3000 and 3500 copper orebodies at Mount Isa, Queensland is well advanced. The choice of internal shaft access was made over alternative methods such as a decline from existing levels and borehole hoisting. The resulting access development requirements and shaft configuration for production have been determined. Several techniques are being studied for shaft development. These include the application of blind shaft drilling and large hole reaming methods as well as conventional sinking techniques. As the 3000/3500 Orebodies extend from 1000 metres to more than 1800 metres below the surface, high stress conditions and ground temperatures ranging from 45CC to 62CC are anticipated. The effect of these on the methods being investigated to create a favourable working environment will influence the final choice. Exploration diamond drilling is in progress to confirm the geology of the orebodies so that planning for their extraction including refrigerated ventilation concepts can proceed.

Jan 1, 1982

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

By Yan D. S

The removal of antimony from a refractory gold-bearing stibnite ore by roasting and selective chlorinating roasting was investigated. The influence of roasting temperature, roasting time, roasting atmosphere and type and amount of chlorinating agents on antimony removal were studied. The laboratory studies carried out included roasting tests of 4 g samples in a laboratory rotary kiln, followed by 400 g samples roasted in a fluidised bed. The test results revealed that antimony was efficiently removed by roasting at temperatures over 800¦C in a nitrogen atmosphere. The most efficient volatilisation of antimony was achieved with the addition of ferric chloride at temperatures between 350-600¦C.

Jan 1, 1995

By B W. Ham

The legacy of underground coal mining may be a land surface which, in parts, may be unstable in the long term. A case study analysis has been undertaken to explain some of the hazards and how the risk may be assessed and managed.The Ipswich Coal Measures were extensively mined with shallow underground workings, which now underlie a number of suburbs in the eastern side of the city of Ipswich in south eastern Queensland. The area was subject to underground mining from the 1840s to 1997. In general, the mines were small, family-owned operations that were restricted by complex geology, interactions with neighbouring operations and ownership of surface facilities. The oldest available mine plans date back to the late 1890s.The residents in these mining areas have a long history of unexpected mining subsidence events. A level of risk management for property owners has been implemented by the Ipswich City Council, which requires a mining subsidence risk assessment to be submitted as part of building applications for property development in the areas suspected of having mining subsidence risk. This discussion examines a series of generic subsidence events and how the risk may be assessed and managed and the hazard controlled.CITATION:Ham, B?W, 2014. The legacy of underground coal mining – mine subsidence: Ipswich coal measures case study, in Proceedings Life-of-Mine 2014 , pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By A Gibbs

The mining sector has been a leader in investing in safety improvement initiatives, yet relatively few mining organisations can accurately track the positive effects of these initiatives or identify areas that may require more attention. The consequences of not taking safety seriously are severe, and unfortunately injuries and fatalities are continuing to occur across the mining sector (Brady, 2019). There is a tendency to turn to lag indicators such as All Injury Frequency Rate (AIFR), Total Recordable Injury Frequency Rate (TRIFR), and Lost Time Injury Frequency Rate (LTIFR) to track these outcomes. As outlined below these approaches are inherently flawed and a renewed focus is needed on indicators within the control of leaders, indicators that have high predictive validity for future events and data that is used in a way to enable learning and change.

May 5, 2022

By Aylmore M. G

Samples have been taken from a two-stage industrial gold roaster treating a pyrite/pyrthotite/arsenopyrite concentrate, in order to describe the mineral- ogy, composition and surface area of the calcines. Sulfides oxidised to produce a porous magnetite in the first stage and a porous hematite in the second, pyrite predominantly roasted via a pyrrhotite intermediate. Sulfur was eliminated in both the first and second stages whereas arsenic was eliminated in the first but retained in the second, partly as rims on hematite particles. The finer sized particles from the cyclones and electrostatic precipitator, whilst having the greatest surface area, were the most refractory with respect to gold solubilization, probably as a result of incomplete decomposition (through short-circuiting) in the first stage, and through a combination of factors such as overheating and entrapment of sub-micro- scopic gold in the second stage.

Jan 1, 1991

By M Berner, N A. Sifferlinger, E Fimbinger

Today, the advance rate of underground roadway development by drill and blast operation is limited by the need to ventilate the toxic blast fumes after each cycle. In deep mines this usually is only possible during shift changes when the related mine sections are free of persons. This results in roadway development advance rates of 4 m per shift, or 12 m per day. For long roadways this is a limiting factor in mining development in deep mines. Companies like EPIROC, KOMATSU, ROBBINS and SANDVIK are making serious R&D efforts to disc-cutting mobile miners to overcome this bottleneck. However, today, the achieved advance rates are less than 12 m per day in hard rock. If we achieve full robotisation and/or teleoperation from a safe place for drill and blast operation of an underground roadway development section, we could eliminate this bottleneck. Poisonous blasting fumes do not affect robots and machines as long as these fumes do not create aggressive acids. If we can keep the blast fumes isolated in the roadway development section for the shift until the next ventilation opportunity (eg shift change or designated ventilation times), we can do the drill and blast cycle more often in a shift, which will significantly speed up the advance rate. This requires robotisation of all work steps in the section: surveying, drilling, charging of explosives, blasting, loading and transporting material, roof support, installation of infrastructure etc. Also, cache storage for the material is needed. Special care for the ventilation system to keep the blasting fumes under control in the section is necessary. The paper discusses the aspects needed to achieve this robotisation and the related technical and operational tasks.

Sep 1, 2024

By A M. Suchowerska, J P. Carter, J P. Hambleton

"In order to effectively predict the roof collapse of underground openings using continuum models, it is imperative that a realistic failure criterion is used to represent the rock mass. However, for coal mining operations, there is still uncertainty as to the appropriate failure criterion that should be used for the coal measure strata. This study compares stability numbers and collapse mechanisms for a rectangular underground opening predicted based on three commonly used failure criteria: the standard Mohr-Coulomb, Mohr-Coulomb with a tension cut-off and Hoek-Brown. Three methods of analysis are considered: an analytical upper bound method an upper and lower bound finite element formulation the displacement finite element method.The theoretical results are also compared with field measurements of subsidence above longwall coal mining. For the standard Mohr-Coulomb failure criterion, the friction angle governs the shape of the collapse mechanism, and the so-called critical width (the cavity width above which failures extend to the ground surface) ascertained from field observations in the New South Wales coalfields corresponds to a friction angle of approximately 30°. On the other hand, predictions obtained based on the Hoek-Brown failure criterion consistently overestimate the critical width. The results also show that tensile failure governs the stability of the cavity and shape of the collapse mechanism when a tension cut-off is introduced for the Mohr-Coulomb yield criterion.CITATION:Suchowerska, A M, Hambleton, J P and Carter, J P, 2014. Prediction of roof collapse for rectangular underground openings, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference, pp 367–374 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 5, 2014

By D McKeon

In July 2006, ten Mining Engineering students and Associate Professor David Laurence from the University of New South Wales (UNSW) participated in the universityÆs inaugural overseas mining field trip. The ten-day trip to western Canada involved visits to two mines in British Columbia, the Diavik Diamond Mine in the Northwest Territories and the Syncrude oil sands operation in Alberta. Importantly, the groupÆs main objective was to gain a global understanding of todayÆs mining industry by observing the different cultural, legal, social and environmental setting found in Canada. It should be noted that the entire trip was planned, organised and directed by the students and benefited from extensive industry support both in Australia and Canada. This report intends to provide an overview of the field trip and describe to a limited extent the Canadian approach to mining.

Jan 1, 2007

By Griffith L, Lama RD

West Cliff Colliery mines Bulli Seam occurring at a depth of approximately 480 m. The Seam is intersected by a number of small shear zones and faults. While the faults have caused displacement of the seam, the shear zones are strike-slip structures with small apparent displacement of seam. Outbursts at West Cliff Colliery occur while driving through these shear zones. Few outburst wave occurred where faults have been intersected. In the last 3 years, over one hundred outbursts have occurred at West Cliff Colliery. The size of outbursts varies from a small bump to exceeding 140 tonnes of coal. A number of studies have been undertaken at West Cliff Colliery to control outbursts and predict Outbursts in advance of workings. These include: geological investigations, microseismic techniques, gas adsorption studies and gas drainage. The investigations to date suggest that outbursts of gas at West Cliff Colliery are more a gas phenomenon similar to what occurs in overseas mines. The results of various investigations are reported. West Cliff Colliery is located in the mid- west of the southern coal fields of N.S.W.

Jan 1, 1980

The Marvel Loch Operations (MLO) plant was treating ores from up to six MLO sources and in addition needed to blend externally sourced ores with its own ores. This presented a metallurgical accounting dilemma, which was subsequently addressed by the design, implementation and testing of an automatic sampling system. The MLO automatic sampler was well designed and has been the subject of previous internal and external reviews. The sampling action is fully automated and the unit is essentially self cleaning particularly when sampling primary ores. The purpose of this paper is to document the rationale behind the design, the specific details of the sampling station, its use for ore purchase purposes and an assessment of the sampling system to meet the needs of the operator.

Mar 1, 2010

By A Galli

Traditionally pit optimisation and scheduling is carried out assuming that the resources, the commodity prices and production costs are all known. Once the pit contour and the mining schedule have been determined, geostatistical simulations can be used to assess the impact of the uncertainty in the resources on the pit design and the schedule, and likewise stochastic simulations can be used to test its robustness to fluctuations in costs and prices. But it would be more interesting to have a dynamic procedure for optimising the pit as the resources become better known and as economic factors such as commodity prices and costs evolve over time. This paper presents a novel approach for doing this. Rather than working with millions of small selective mining units, it was decided to work with large blocks, called macro-blocks. Mining sequences are defined as the quantities to be extracted from each macro-block in each time period. Feasible mining sequences are mining sequences that respect the accessibility constraints, and also the geometric constraints on the amounts that can be extracted from any one block over time, or from all the active blocks at a given time. Having defined feasible mining sequences, their mathematical properties were studied. It was found that natural breakpoints occur in the sequences when one set of blocks have been completely mined out, thereby opening up access to others. It was discovered that families of sequences exist, and that they are convex and closed under certain types of row permutation operations. Convexity is an advantage when optimising. The closure property opens up the possibility of mixing and matching subsequences of rows in the sequences. Another interesting property is that the sequences form branching families, rather like the binomial and trinomial trees used to model prices in finance and in real options.It is easy to generate large numbers of feasible mining sequences randomly. A two-step procedure is used to find the best one (or the best few) using three economic criteria: expected NPV,the probability of a negative NPV, and the percentage of years when the cash flow is negative. The procedure was tested on a synthetic gold mine based on the characteristics of the Essakane mine in Burkina Faso. The results were encouraging.

Sep 26, 2011