Search Documents

By R P. Varden

This paper looks at the design of the Bentayga raisebore with subsequent back analysis using a LiDAR survey. A search for LiDAR raisebore assessment publications shows little work has been done on this subject. The paper examines the empirical design and RS2 modelling assessment with the bored condition. The high resolution of the LiDAR enabled mapping of weak structures that were located on the geotechnical investigation hole the orientations of which could not be determined. In addition, the scan showed were water ingress was occurring, potential stress overbreak and structural controls on stability. The LiDAR results were able to confirm no additional support work such as a shotcrete liner is necessary. The LiDAR results have been analysed in one metre increments as volume of overbreak against the empirical stability criteria (McCracken & Stacey 1989). The future use of LiDAR mapping over a range of rock mass conditions will provide quantification of the established empirical assessment improving its reliability. It is also a useful and accurate tool to monitor long term stability of a raisebore due to stress change or ore pass due to wear.

Mar 15, 2021

By Snowden C. T

B Lens Main is a scheelite orebody with an average dip of approximately 15¦ and thickness ranging from 1.5 to 6.0 m. The orebody is overlain by a banded section of ore and waste which tends to slab off if left unsupported. It was originally planned to mine a large portion of this orebody by room and pillar methods, with existing diesel trackless equipment. This, however, proved unsuitable for a number of reasons and the smaller scale method of slot stoping with hand machines and scrapers was employed. The following major problems were encountered. 1. The method was new to the mine and the work force, and had to be commenced quickly using existing or easily obtainable equipment. This is gradually being overcome by training, modification of procedures and introduction of more suitable equipment. 2. The slabbing from the hanging wall had to be controlled, either by support or by mining this low grade section and accepting the resultant dilution. This has been approached in a number of ways, depending on conditions and the method will have to be further modified as different conditions are encountered in new areas.

Jan 1, 1977

By A Minchinton

With blasting, all far-field phenomena including, but not limited to, stress wave propagation, fracture, vibration and muck pile formation are intrinsically and irrevocably dependent upon near-field phenomena or mechanisms that we describe using physics-based mathematics typically transcribed into computer codes. The energetics involved in such near- to far-field transitions are not fundamentally relevant as they are simply progenitors of these processes.The notion of explosive energy as a descriptor for explosive or blasting performance is a case in point. These energies, which are generally used in blasting tables, are almost exclusively based on ideal detonation theory alone and do not include the influence of the rock, charge diameter, blasthole length and the late-time dynamic expansion that can be predicted using codes based on non-ideal detonation theory.With decoupled charges in presplits for example, the pressure drop between the charge and the blasthole wall can be simply described to first order using the energy relationship associated with adiabatic expansion. However, a more realistic mechanistic solution involves interacting fluids and turbulence leading to dynamic processes such as the channel effect.CITATION:Minchinton, A, 2015. On the influence of fundamental detonics on blasting practice, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 41–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R H. Knight

Production mine geology must be accurate and efficient in order to reduce risk and ensure that ore value and mining operation revenue are maximised. Present grade control practices are commonly based on outmoded and inaccurate 2D geological mapping techniques where spatial relationships are estimated by eye, sketched by hand and projected to arbitrary reference planes. The 3D mapping approach outlined in this paper integrates 3D photogrammetric imagery with implicit modelling techniques to enable more accurate grade control and reconciliation in underground mines. High-resolution stereo photographs are taken of daily ore development headings. Ore contacts are traced directly on a 2D face photo using a stylus and rugged tablet. Area-weighted face grades are estimated and calculated on mapped 2D face planes. In the office, a 3D photorealistic mesh is processed and georeferenced. 2D face mapping data is transformed into its actual 3D location and true 3D mine mapping is performed by digitising oriented 3D polylines representing ore contacts and other geological features directly onto the image surface. Three-dimensional spatial relationships are fixed, eliminating the projection error of traditional 2D methods. Ore envelope and waste solids are modelled within the closed, drift-round mesh. Volume-weighted ore envelope and round grades, as well as round volume and tonnage, are calculated. Ore/waste classifications, grade, tonnage and per cent dilution are quantified per round, visually assessed in 3D and reconciled with short- and long-term models on a daily basis. Updated geological continuity models provide geological guidance in development headings under geological control and accurate 3D structural and form-line mapping improves definition drilling and stope planning. Three-dimensional imagery provides a permanent detailed survey and geological record of mine workings that can be revisited virtually to reinterpret geological ore controls in light of new observations and insights. In addition images can be used to monitor daily production performance, create training scenarios for miners, engineers and geologists and prepare management presentations. This approach adds value to underground mines by improving the accuracy and efficiency of mine geology practices. The method is particularly effective in mines with visually distinct and geometrically complex orebodies, such as those in the Balmat zinc mine located in New York State, USA, which are used to illustrate the method.CITATION:Knight, R H, 2017. 3D mine mapping – improving grade control and reconciliation in underground mines using photogrammetric imagery and implicit modelling techniques, in Proceedings Tenth International Mining Geology Conference 2017, pp 203–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By J P. Evert

Didipio gold-copper mine operation is situated in the island of Luzon, approximately 270 km north of Manila in the Philippines, in an area of high seasonal rainfall. The hydrogeological water flow model implied that there would be high connectivity between regional structures and underground operations. This model predicted that underground mine groundwater inflows were expected to quickly rise as the decline progressed to a peak of 510 L/s. Designing a capital pump station to deal with 510 L/s has its own challenges, however developing the decline down to the required level, always dealing with 300 L/s of water and constructing the pump station is extremely challenging and required a robust water management plan and mine design. When dealing with expected high volumes of water, underground mine design and scheduling plays a key role in protecting electrical infrastructure, equipment, secondary pumps, and the decline from flooding. A good drainage system and controlled dewatering plan is essential for safety and progress. This paper details the dewatering techniques and mine designs required to accomplish decline development with high water inflows as used in the Didipio project. It will describe the learnings and outcomes that are achievable with a flexible design, as new structures are mapped, and water intersections are increased. It also highlights the potential for adaptability in mine planning to provide evolving improvements or to evade problems that are expected from the constant reconciliation of data recorded during development.

Mar 29, 2023

By Colwell JB, Cronan DS

Manganese nodules cover great areas of deep ocean floor far from land, and have long been considered a major potential resource of nickel, copper, cobalt and perhaps manganese. A decade ago there was a period of intense evaluation of nodule fields, especially those lying between the Clarion and Clipperton Fracture Zones in international waters southeast of Hawaii. There, nodules are abundant and of high grade (average of 2.4% Ni+Cu+Co). The evaluation activity has since declined, but a recent agreement on lease boundaries among all interested parties may lead to a resurgence of work. Indeed, French and Japanese groups have pushed ahead with field and economic assessments.The Southwest Pacific, where there are large nodule fields in the waters of the Cook Islands and Kiribati, has seen considerable assessment of resources in the last ten years, especially through a major field programme of the Japanese Metal Mining Agency. The best prospect appears to be in the South Penrhyn Basin, in Cook Islands waters, where nodules are very abundant but of only moderate grade (1% Ni+Cu+Co). Using a cut-off of 5 kg of wet nodules per m2, Cronan (1989) and Cronan et al. (1989) have estimated the total resource to be a huge 110 million tonnes of Ni+Cu+Co.

Jan 1, 1990

By Svensson J

The nickel segregation process is one of the methods for treating nickel oxide ores. In this process nickel oxide ores are heated together with a small amount of the carbonaceous reductants and halides to about 800-950¦C. The reduced nickel segregates onto the surface of the carbonaceous reductants in the form of metallic particles which are recovered by magnetic separation or flotation. Pilot plant tests for the extraction of nickel from nickel oxide ores have been made using nickel segregation process by means of a new roasting installation which is called the "Mechanical Kiln" (2.5m~ x 3m,') with autogenous heating. Nickel oxide ores containing about 2.5%Ni were mixed with 2.5%CaC12 and 2.7%coal, and continuously charged into this installation at the rate of 60kg/h in continuous operation for 30 days per trial.

Jan 1, 1980

By B Belle

"Mines around the world are inherently and operationally diverse. Current methodologies for the design of mine ventilation and cooling infrastructure involve controlling major safety and health hazards. Globally, it can be estimated that mine ventilation systems from various commoditiescirculate over 150 000 m3/s of exhaust air through shafts. Additionally, over 2 000 000 workersare transported every day through shafts in labour-intensive mining countries like China, India,Southern Africa, and the Americas. A key objective of this paper is to share experiences and provide a case for the revision of ætime-honouredÆ ventilation design parameters based on a benchmarking exercise on design exhaust shaft velocity from various global operations (gold, diamond, platinum, coal and base metals). An active fi eld observation on exhaust shaft velocity has indicated that, regardless of the commodity or continent where the mine operates, almost all life-of-mine (LOM) design parameters provided are in the same range of 20 m/s to 22 m/s, which is not convincing considering signifi cant variations exist in shaft depths, geography, commodity, operating and capital costs. From a due diligence perspective, there are no documented views that are available on the most widely used design exhaust air velocity. Based on the global exhaust shaft velocity data, it is noted that a significant portion of shaft velocities are outside the current design velocity of 20 m/s (some operating up to 30 m/s) and other signifi cant portions of the exhaust shafts operate in the critical velocity range. In the case of Australian coal mines, limited data suggests that none of the mines have ever reached the LOM design exhaust shaft velocity. It is self-evident that when the shafts are not operating at their design quantities either the mine system resistance is low or the ventilation and main fan is operating ineffi ciently. The most common reasons given for not reviewing the shaft system were, ætime-honouredÆ design parameter are being used and cannot be changed, mine fan pressure limits, possible fan blade damage, possible spontaneous combustion risks, leakage or simply did not consider such a possibility. In conclusion, the study has reiterated the historic lessons that a safe and expensive airway should not be utilised uneconomically by circulating too litt le air through it."

Jun 1, 2012

The Mine Safety and Inspection Act, 1994 of Western Australia recognises the importance of ground control in underground mining. The recent safety performance of underground mining is summarised in terms of the most common causes of injury and fatal accidents. A review of current ground control practices is presented and the concepts of local and large-scale ground control are introduced. The need for a more systematic approach to ground control is considered to be directly related to requirement to improve safety performance. The new regulations will require that certain geotechnical issues be addressed during the life of a mine. To comply with the regulations it is suggested that a ground control management plan be developed for each mine. The geotechnical issues associated with the ground control management plan are reviewed and hazard recognition aspects discussed.

Jan 1, 1995

By T Dawson, B Haskins

Fatigue is it the newest buzz word or is fatigue a real phenomenon that is creating safety and organisational risk for you? There is no debate that fatigue is natural, and it affects us all, just like gravity; however, there has been much debate on the severity of its impact in the workplace. For many years the impact was not measurable, hidden out of sight and, quite frankly, written off as the infamous ‘operator error’. Over the last several years, advancements in technology have provided safety and health professionals, sleep scientists, fatigue experts and organisations with the ability to monitor and detect fatigue events in real time, as well as predict and monitor increased risk for fatigue events. Caterpillar Safety Services has assembled an extensive and exceptional set of technologies that will provide the best methods and data to measure the impact of fatigue. This paper will discuss fatigue in the workplace and review the technologies and data sets available, which will allow the reader to determine whether this risk is real or rubbish.CITATION:Haskins, B and Dawson, T, 2017. Fatigue risk in your operations – real or rubbish? It actually depends , in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 137–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J Ross

The foundation of effective leadership is communication. You can have all the leadership theories, models and training you want, but in the end it is all about leaders talking to, listening to and understanding the point of view of those below and above them.The foundation of effective safety is peoples’ behaviours. Every incident, every near miss and every safe act comes down to what one person does and how that affects themselves and others. We tend to focus these behavioural considerations on the people at the ‘coal face’, those most in harm’s way. But it is the individual behaviours of everyone in the organisation, particularly those at the top, which are just as (if not more) important. The foundation of effective safety leadership in the mining industry is that it starts at the top, with the individual behaviours of leaders. The behaviours of each and every leader will be reflected in their teams. And where their teams are made up of leaders, these leaders will pass these behaviours on to their teams and so on. It’s the sum total of what people see their leaders do and what they do as a result, that creates the ‘culture’ of the business – and it’s this culture that makes or breaks how safely people work.

Mar 21, 2011

By J V. Mehrabani, A R. Sayadi

Adequate estimation of equipment costs is a key factor in a feasibility study and in evaluation of design alternatives for mining and mineral processing projects. Inaccurate early cost estimation could lead to the elimination of investment benefits. However, this estimation is complex and time consuming because of data accessibility problems and consequently access to a rapid, up-to-date and accurate tool is desirable for carrying out cost estimations.This paper describes the development of models for estimating capital and operating costs for a jaw crusher, which is used as the primary crusher for a wide variety of mineral beneficiation plants, applying single and multivariate regression analyses, together with the design of experiment approach, based on principal component analysis. Explanatory variables include gape size, length of feed opening and power as numeric (quantitative) variables and toggle type (single or double) and the existence of extra heavy duty construction as categorical (qualitative) variables. The performance of each model has been investigated and comparing the estimated R-squared (R2) of each model, the best was selected and its validity examined. The cost models include the capital and operating costs along with the operating cost components. The results indicate that the suggested best cost model is sufficiently accurate for use in feasibility studies.

Sep 26, 2011

By G Corbett

Epithermal Au-Ag deposits form in the upper 1 km of the crust and are therefore best preserved in the less eroded Pacific rim arcs, although also recognised elsewhere. Two profoundly different ore fluid types give rise to low and high-sulfidation styles apparent as variations in ore and gangue mineralogy as well as characteristic zoned wall rock alteration. Low sulfidation epithermal Au deposits are derived from near neutral composite magmatic-meteoric fluids and divided into a group with a stronger intrusion association within arcs grading in time and space from: quartz-sulfide Au + Cu, to carbonate-base metal Au, and the epithermal quartz Au + Ag, whereas in strongly extensional settings the influx of meteoric waters promotes the development of chalcedony-ginguro banded Au-Ag epithermal veins. In the presence of continental crust particularly in Latin America polymetallic Ag-Au veins represent a Ag-rich equivalent of carbonate-base metal Au and passes upwards to chalcedony-ginguro Au-Ag style. By contrast high-sulfidation epithermal deposits are deposited from an acidic magmatic fluid which provided characteristic hydrothermal alteration by reaction with wall rocks grading outwards as mineral assemblages dominated by: vughy silica, alunite, pyrophyllite-diaspore, dickite-kaolin and then illite-smectite neutral clays. Au mineralisation is commonly refractory with enargite deposited dominantly later within the silica zone.Exploration for epithermal Au deposits benefits from an understanding of the controls to mineralisation which commonly give rise to the development of ore shoots with widest and highest Au grade ore zones. In low-sulfidation systems a combination of competent host rocks, dilatant structures, higher grade styles of mineralisation and efficient mechanism of Au deposition, contribute towards ore shoot formation. High-sulfidation epithermal Au systems occur in permeable volcanic and breccia host rocks which are linked by major structures to the magmatic source.CITATION:Corbett, G, 2013. Pacific Rim epithermal Au-Ag, in Proceedings World Gold 2013 , pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G W. Swana

Elastoplastic parameter is a parameter that describe how much materials behave elastically up to certain stress states and plastically thereafter (Hudson and Harrison, 1997). In the continuum analysis, two main parameters of the elastoplastic parameter are modulus elasticity and Poisson’s ratio. In the slope, elastoplastic parameter holds the main role for stability related to deformation in ductile type of rock. There’s a limitation to determine elastic or plastic deformation at the field for ductile rock type. Field manifestation commonly showed that there was no accumulation zone during and after the sliding failure mechanism, in other hand, at the research area, manifestation of deformation at the toe of slope only indicated by bulging shape. This paper will focus at the sliding failure occurred at Coal mining Pit Y owned by Arutmin Indonesia, which according to failure investigation report similar with the condition described above. This paper also will be based on two hypotheses, first hypothesis is claystone rock mass has not been reached plastic deformation yet and the second hypothesis is there is a chance that elastoplastic parameter of the rock mass has been changed during the deformation/sliding failure process. Research method of this paper are back analysis using probabilistic analysis in Finite Element Method (FEM), which conducted before and after failure. Then, the result of the displacement or deformation of the analysis will be checked with the actual deformation shape. Meanwhile, the change of the elastoplastic parameter will be analysed and interpreted. This paper hopefully able to be developed to study about elastoplastic behaviour of rock mass in actual condition and the influence of another uncertainty factor which determine the slope stability.

Nov 29, 2022

By P Ridley

EnergyAustralia’s Sydney Central Business District (CBD) cable tunnel network will form a loop 6.2 km in length. The 3.2 km long, 3.5 m, diameter city east cable tunnel (CECT) currently in design, will complete the loop in 2014. This paper discusses the ventilation design of the CECT, considering operation for four functions:1. normal (unmanned),2. access (manned),3. purge, and4. emergency fire modes.The dominant design criterion which determines the required ventilation capacity for CECT is the specification of an upper air temperature limits of 35°C (dry bulb) and 24°C (wet bulb) for manned access, during all ambient weather conditions and cable heating loads. Simplistic static heat transfer analyses do not yield a sufficiently accurate calculation of tunnel air temperature and humidity to provide a safe and yet economical design. The primary refinement in the analysis discussed in this paper is associated with modelling of the system’s dynamic behaviour.Our means of analysis is through a thermo-fluid-dynamic simulation of the interactions between the diurnally and seasonally varying loads (cable heat generation, ambient air conditions and groundwater inflow), tunnel airflow and the resulting tunnel air temperature and humidity. These simulations are validated using experimental data from the existing city south and city west cable tunnels.Fire life safety scenarios are also analysed and discussed in association with the ventilation design. Ventilation strategies are developed for dealing with such emergency fire situations.The understanding and insight provided by the work offers the ability to optimise ventilation plant provisions in future cable tunnels, particularly long and high energy density tunnels.

Mar 8, 2011

By O A. Aladejebi, S Mitra, T Singh, D J. Pinson, S, S J. Chew, T Honey

Currently, many commercial sinter plants are exploring the potential addition of high-grade iron ore concentrates to improve the sinter grade. A better understanding of the ore blend, granule behaviour and green bed properties is critical to making this change and maintaining productivity in the sinter plant. This study compared the performance of a laboratory scale granulation drum to a commercial scale unit. The blend used was an Asia-Pacific style sinter blend containing iron ore concentrates. The operating conditions of the two granulation drums (laboratory and commercial scale) were fixed at the same Froude Number (0.00337), space factor (15 per cent) and residence time (4.5 mins). The granules were characterised by measuring their mean size, size distribution and green bed voidage. It was found that the laboratory scale granules were representative of commercial sinter plant granules at similar moisture content. When the moisture was fixed at ~6.9 per cent, granulation time had no significant effect. A further fundamental investigation was undertaken to measure the water holding capacity and intra-particle porosity of the individual ores used in this study. The kinetics of water absorption were measured which showed that water absorbs quickly into the ore particles within the first 60 seconds, slowing down until final saturation was attained after six hours. A linear relationship between the water holding capacity and intra-particle porosity was noted for different ore particle sizes. The results of this study provide a baseline understanding of the current commercial sinter blend and encourage exploring the specific effect of increasing the proportion of ultrafine concentrates in sintering in a future study.

Sep 18, 2023

By D K. Weatherley, G R. Ballantyne, S Ali, M Yahyaei, M S. Powell

This paper explores development of a novel ore characterisation method for the precise measurement of practical minimum comminution energy. A monolayer of particles with a narrow size distribution is broken using a precision rolls crusher (PRC); an ore characterisation device developed to overcome the shortcomings of conventional tests. For energy measurement, PRC uses two shaftmounted rotary torque transducers. These transducers acquire precise torque and angular speed data in response to the load applied to the rotating shafts during breakage events, which is converted into energy. The test progressively crushes feed particles down to final product size in many controlled breakage stages. The generation of fines in each breakage stage is then plotted as a function of input energy. The inverse of the gradient of this plot provides the size specific energy (SSE) in kWh/t of material generated below a predefined marker size; -75 μm in this case. The PRC has potential to evolve as a geometallurgical ore characterisation test—it is simple, fast, requires small sample mass (200–300 g), covers a wide feed particle size range (10 mm to 115 µm), and provides ideal SSE measurements that can be used for the calibration of on-site production equipment.

Aug 24, 2022

By Carter J. P

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By Royle A. G

The paper describes a geostatistical structural analysis of an 80 square mile lease of the Athabasca tar sands. Each step of the analysis is presented with the ultimate objective of condensing the principal structural characteristics of the chosen regionalised variables into the opera- tional form of the variogram model. The variogram model is then used to form kriged local and global estimates, with the corresponding estimation errors.

Jan 1, 1977

By D J. Brake

The risk from fire remains one of the most serious of underground mine disaster scenarios. The impacts of mine fires on the underground ventilation system and the production of toxic gases have been difficult to model and therefore assessments have relied largely on empirical data, historical precedent and subjective opinions. Underground fire modelling software has had limited availability and been technically challenging and time consuming to use especially for routine mine investigations. There has also been no well-accepted set of assumptions for fire modelling in mines, which has resulted in a lack of confidence in adopting its use more widely. This paper describes modelling of three critical fire scenarios in underground hard rock mines: a fire (LHD) in an underground diesel refuelling facility, a fire in an underground explosives magazine and a fire on an underground ore transport conveyor. Modelling was undertaken using VentsimÆs VentFIREÖ fire simulation module. It describes the basis of design, the key assumptions, the methodology used and provides examples of the outputs, conclusions and recommendations. It reviews the impacts of these fires on egress and entrapment strategies in the mine. Some general principles regarding improvements to ventilation circuit design based on this analysis are also recommended. Whilst the fire scenarios were based on actual case studies, they have been disguised for this paper.CITATION:Brake, D J, 2013. Fire modelling in underground mines using Ventsim Visual VentFIRE software, in Proceedings The Australian Mine Ventilation Conference , pp 265-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013