Search Documents

Discussion of the paper of W. R. Shimer and F. O. Kichline, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 81, September, 1913, pp. 2361 to 2377. ALLERTON S. CUSHMAN,* Washington, D. C.:-I have been much interested in Mr. Shimer's valuable contribution. The apparent fact that the oxides of certain metals which are not reduced by hydrogen per se, are reducible when the oxides are dissolved in iron in small quantity, is brought out for the first time, and is worthy of the careful attention of investigators. The Ledebur method has been subjected to considerable criticism, owing to the alleged fact that it did not measure the oxygen combined with impurities. Personally I have found the method extremely helpful in spite of the minute quantities of oxygen with which it deals. Mr. Shinier points out that the highest oxygen he obtained by over-blowing was 0.074 per cent., while the minimum quantity in a properly finished steel was in the neighborhood of 0.02 per cent. The Ledebur method is used as a constant check on the quality of heats made in practice under my direction. In dealing with a very pure commercial iron, we should expect to find and would find difficulty in galvanizing sheets made from a heat running 0.07 per cent. oxygen. In fact, we do not like to have the oxygen rise above 0.03 per cent. I am inclined to agree with the author that excessive oxygen leaves a bath of metal in a very short time, but nevertheless I believe it takes only a very little combined oxygen to begin to make its presence felt in the pickling and galvanizing department, when sheet metal is the product manufactured. As Mr. Shimer points out, the higher the carbon, the lower the oxygen danger, and it is partly for this reason that the manufacture of carbon-free metal in the open-hearth furnace has to be so very carefully watched and controlled from the furnace through to the finished product. It is quite possible that, there is a critical temperature of dissociation between iron and oxygen, although the critical points may vary in baths of different carbon content. Unfortunately, the accurate determination of the temperature of a molten bath at the time of pouring or teeming is a very difficult matter. For a long time I have been wishing that there were some reliable data which would indicate the effect of the tem-

Jan 12, 1913

By W. A. Backofen, D. H. Avery, W. F. Hosford

Sheets of the magnesium alloys AZ31B, HK31A, and ZE10A in several different tempers were tested in tension and determinations were made of the ratio of width-to-thickness strain. A marked increase in the ratio with tensile straining and a dependence upon alloy and test direction are rationalized in terms of a balance between the amounts of basal and prism-plane slip. All such variations are related, in turn, to the prevailing crystallographic texture. Fracture appearance is explained on the basis of anisotropy in plastic flow, and implications for developing texture -hardening effects in these alloys are discussed. ThE crystallographic texture or preferred orientation of a given material is determined by details of processing history. Such texture is known to influence many aspects of material behavior, in particular both the yielding and strain-hardening characteristics which are of special interest in the present work. Traditionally, the resulting plastic anisotropy has not been regarded as especially desirable. Earing in drawn sheet is perhaps the most common example of an unwanted effect of texture. However, it has also been recognized that suitable textures may be usefully employed to improve drawability,1,2 as a specific example, and generally to control yielding resistance under combined-stress loading.374 Texture would seem to be a detail of structure not yet exploited to nearly the fullest extent. A convenient basis for characterizing anisotropy in plastic behavior is the ratio of width-to-thickness strains obtained in a tension test;5&apos;6 the parameter is frequently labeled "R" and its value is revealing with respect to the nature of the prevailing texture. R gives a useful measure of a material&apos;s "thinning resistance". For an isotropic material, R = 1. With R > 1 the increased through-thickness strength in a sheet means greater resistance to yielding under biaxial tension, or "texture hardening";3&apos;4 if R < 1 the result may be a "texture softening" under the same loading conditions.4 Most R data relate to steel sheets for deep-drawing applications. Values for steel and other materials of cubic structures are not often much greater than 1 and nearly constant with strain in testing.1,2,7,8 To explore the implications of plastic anisotropy further, it was felt that experiments with much more strongly textured materials would be useful, and this led to the choice of magnesium alloys. The "ideal" sheet texture for magnesium contains the (0001) plane in the rolling plane, which ought to lead to R values approaching infinity. However, departures from the ideal texture, the possibility of slip in non-close-packed directions, and deformation by twinning would all be expected to introduce some range of R. Accordingly, studies on these materials were undertaken. EXPERIMENTAL Alloys in sheet form, Table I, were selected to obtain a variation in crystallographic texture, in the expectation that this would be reflected in differences in plastic anisotropy. Pole figures constructed by the Schulz surface-reflection technique9 were provided with the experimental materials by the Dow Metal Products Co. Profiles of pole density along great circles through the rolling (0 deg) and transverse (90 deg) directions were prepared from the pole figures and are collected in Figs. 1 and 2; considerable departure from the "ideal" (0001) alignment in the rolling plane is evident, with the largest angular spread in both directions being found in the ZEl0 alloy. Results of tensile tests on full-thickness specimens of 6-in. gage length by 1/2-in. width are given in Fig. 3 as engineering stress-strain curves* in rolling and transverse directions. All tests but one were made at a constant drive rate of 0.02 in. per min, and the final values of percent elongation at fracture, over the initial 6-in. gage length, are noted at the ends of the curves; one test on ZE10A-

Jan 1, 1965

By F. Weinberg

Measurements have been made of solute segregation during dendrilic growth by using radioactive solute elements and ,measuring the activity of den(12-ites cut from decanted specimens. This has been done for both lead awl tin based binary alloys contaitzing the following solute additions: Ag, T1204, was dependet on ko, the equilibrium distribution coefficient in the following way Fay k &apos;c 0.1, C/C 0.6; for k0 >0.1. 0.6 <c,/c,< I. Qualitative obse?-vations were madc of dendritic segregation, by using autoradiographic techniques, for the Sn + Ag110 and Sn + Tlo4 systems. The observation were found to he in general agreement with the measurements ofCA/Co. Autoradiographic were also obtained of scctiolccl delzr11-iie stalks. These indicated that the stalks had a substructure, dclileated by solute corzetlt?atio?zs nlolg the substructure walls. A new dendrite growth direction <JI2> is reported for tila. SOLUTE segregation in dilute binary alloys has been investigated by Pfann,&apos; Smith, Tiller, and Rut-ter,&apos; and others. They considered the case of a slowly advancing plane solid interface, and derived expressions for the distribution of solute in both solid and liquid during solidification. To determine these expressions, they assumed no diffusion in the solid and either complete mixing in the liquid:&apos; or diffusion controlled solute movements in the liquid without any convective mixing.&apos; The present investigation considers solute segregation during dendritic growth, in which case the solid-liquid interface is not plane, and the growth rates are rapid. Segregation under these growth conditions has not been treated mathematically, because of the relative complexity of the system. It has been suggested by Chalmer, on the basis of preliminary results, that an alternative to the diffusion and heat flow controlled conditions during growth is &apos;diffusionless" dendritic growth in which solid is formed with the same composition as the liquid. He suggests this type of growth may depend upon a solvent-solute relationship that permits some solid solubility without excessive increase in internal energy, as is the case for solutions of tin in lead. On the other hand, Montariol,4 and others, have shown experimentally that some segregation does occur during dendritic growth in metals using etching and radioactive tracer techniques to indicate the concentrations of the solute. The present investigation was undertaken to determine, both qualitatively and quantitatively, the extent of solute segregation associated with dendritic growth in a series of binary alloys, as a function of solute concentration. PROCEDURE The solvent materials used were Vulcan Electrolytic tin (99.997 pct purity) and Tadanac lead (99.998 pct purity). The solute materials were Zn, Sn, and Sb (better than 99.998 pct purity), Ag and Co (99.5 pct purity), and T1 (Fisher "purified" metal sticks). Activation of the solute metals was carried out in the reactor at Chalk River, Canada. Master alloys were prepared by induction heating from the radioactive solute metal and the pure solvent, under argon, in graphite crucibles. Pieces of these alloys were then added to the solvent to give the required solute concentration. Dendrites were grown in essentially the same manner as that described by Weinberg and Chalmer, , in which controlled orientation single crystals were grown dendritically in horizontal graphite boats, and the liquid decanted. The crystals were grown and decanted in an atmosphere of tank argon. Before decanting, a sample of the liquid was drawn up in a glass tube and allowed to solidify rapidly. The orientations of the single crystals were such that <loo> was parallel to the growth direction, and (100) in the horizontal plane for lead, and [1101 and (110) respectively for tin. With these orientations long dendrite stalks formed along the bottom of the boat in the dendrite direction (<100> for lead and [I101 for tin) from which secondary branches grew. Only these secondary branches, which grew freely in the liquid from the dendrite stalk to the liquid surface, were used in the measurements. Accordingly, effects due to substrates and oxides on the surface of the liquid need not be considered. In order to measure the solute concentration C, of the dendrites, individual dendrite stalks were cut from the decanted specimens, remelted, and formed

Jan 1, 1962

US 4,141,854-Method of resolving water-in-oil emulsions from the organic solvent extraction of uranium from an aqueous ore leach solution The emulsion is treated at optimum temperature with a water-soluble acrylamide copolymer which contains 5-50% by weight of a lower alkyl substituted tertiary aminoethyl methacrylate or quaternary ammonium salts thereof The emulsion is broken, enabling recovery and reuse of the organic portion of the emulsion A M Pavilcius and M A Latko, assigned to Nalco Chemical Co Feb. 27, 1979 3 pp (252-301 1W) Filed: 12-14-77 (860,542). US 4,142,952-In the recovery of copper from an ore leach solution, the solution is contacted with a water-immiscible organic solvent containing 5 to 20 g/L of o-hydroxyaryloxime and 2 to 20 times the weight of the o-hydroxyaryloxime of nonylphenol The loaded solvent phase is separated from the aqueous phase and stripped with sulfuric acid Copper is recovered rapidly and in high yield from aqueous solutions containing high copper concentrations R F Dalton, as¬signed to Imperial Chemical Industries Ltd Mar 6, 1979 6 pp (204-106) Filed 1-3-77 (756,067). Priority: United King¬dom, 1-30-76 (3788/76), 6-15-76 (24722/76), and 10-21-76 (43711/76). Same- British 1,549,615, dated Aug. 1, 1979 US 4,148,631-In the recovery of nickel and cobalt from a mixed sulfate ore leach solution, both metals are extracted by means of a cationic extractant, the loaded extractant treated with an aqueous chloride or thiocyanate solution to back extract the cobalt, and the cobalt then recovered by solvent extraction or ion exchange with an anionic extractant Recovery is effected in a relatively few extraction steps. F Babjak, V A Ettel, and K. R Dymock, assigned to Interna¬tional Nickel Co , Inc, Apr. 10, 1979 6 pp (75-101 BE) Filed¬7-27-78 (928,401). Priority- Canada, 12-28-77 (293,967) US 4,148,813-An improved extractant for use in the recov¬ery of nickel and cobalt from an ore leach solution comprises a water immiscible organic solvent system containing solubilized mercaptide ions, e g , dodecanethiol. Cobalt and nickel mercaptides solvated in the organic phase are easily stripped in the presence of carbon monoxide and an aqueous alkaline solution A. S. Rappas and J. P. Pemsler, assigned to Ken¬necott Copp

Jan 1, 1980

By Edward Judd

THE old Cerro de Pasco smelter at La Fundicion, near Tinahuarea, 9 miles. from the Cerro de Pasco. mines and at an elevation of 14,300 ft., has now been replaced by a thoroughly modern smelting plant at Oroya, the junction point of the company&apos;s private railroad with the Central Railway, of Peru. This site has the advantages of being closer to the Morochoca mines, as well as nearer to the port of Callao, and at the same time is 2000 ft. lower in elevation, which benefits not only the cost of transportation but also the tech-nical operation of blast furnaces , and converters. The Oroya smelter was designed with the idea of .smelting about 2500 tons of. ore per day, but having in mind the possibility of increasing its capacity, all departments of the plant can be extended within reasonable -limits; for instance, if it is found that reverber-atory smelting is cheapest, taking into consideration the cost of fine crushing and fuel, it is possible to extend the roaster and reverberatory plants accordingly. The ore handling system is modern, consisting of belt conveyors, reclaiming machines, and electrically driven calcine cars, all requiring the minimum of labor. Waste heat from the reverberatory furnaces is utilized in boilers for the production of power to operate the plant, and the power house is equipped with condensing units to obtain the highest economy. Shop installations for the making of all repairs required for the smelter are unusually complete, includ-ing iron foundry, steel foundry, forging and machine shops, carpenter and pattern shops, and an electrical shop. There is also a plant for the production of all clay and silica refractory brick used in the furnaces; this is situated on the smelter site and is conveniently arranged for receiving raw materials and delivering finished brick to the several departments of the smelter. The laboratory is in a wing. of the general office, which is a two-story brick structure, situated on the smel-ter site.

Jan 10, 1923

By H. H. Stoek

A study of Americarf coal-mine practice shows two of its distinctive features to be: A greater number of accidents per thousand employees than in any of the other leading coal-producing countries; a much greater percentage of the coal lost than in any of the other leading coal-producing countries. Although our subject is mainly concerned with the second feature, any consideration of mining methods should include safety, efficiency, and economy or costs. If the argument could be offered that our wasteful mining was necessary on account of safety, and that it is carried out with less loss of life than in other countries, the plea for conservation of coal could not he so strongly urged. But when we are wasteful of both life and property, the subject merits more: consideration than it has received. Some coal operators will doubtless say that the unit of accidents should be the number per million tons produced rather than per thousand employees, for by adopting this unit America probably stands in the lead rather than the lowest among the countries. However, vital statistics are not usually so expressed by other governments, by life and accident insurance companies, or in other industries, and it is merely begging the question and attempting to bolster up a bad condition to adopt a peculiar unit for the statement of our accidents. For many years the statement was made by various agencies, and was unchallenged, that "For every ton of bituminous coal mined in the United States a ton had been lost in the way of pillars left in the mines." This statement was undoubtedly true for many years, and although in the past decade some progress has been made toward obtaining a higher extraction, and in some districts very decided progress, the loss is still great; and, although no exact data can be given, it is probable that for the United States as a whole at least one ton is lost for every two mined.

Jan 1, 1923

By H. H. Stoek

A study of Americarf coal-mine practice shows two of its distinctive features to be: A greater number of accidents per thousand employees than in any of the other leading coal-producing countries; a much greater percentage of the coal lost than in any of the other leading coal-producing countries. Although our subject is mainly concerned with the second feature, any consideration of mining methods should include safety, efficiency, and economy or costs. If the argument could be offered that our wasteful mining was necessary on account of safety, and that it is carried out with less loss of life than in other countries, the plea for conservation of coal could not he so strongly urged. But when we are wasteful of both life and property, the subject merits more: consideration than it has received. Some coal operators will doubtless say that the unit of accidents should be the number per million tons produced rather than per thousand employees, for by adopting this unit America probably stands in the lead rather than the lowest among the countries. However, vital statistics are not usually so expressed by other governments, by life and accident insurance companies, or in other industries, and it is merely begging the question and attempting to bolster up a bad condition to adopt a peculiar unit for the statement of our accidents. For many years the statement was made by various agencies, and was unchallenged, that "For every ton of bituminous coal mined in the United States a ton had been lost in the way of pillars left in the mines." This statement was undoubtedly true for many years, and although in the past decade some progress has been made toward obtaining a higher extraction, and in some districts very decided progress, the loss is still great; and, although no exact data can be given, it is probable that for the United States as a whole at least one ton is lost for every two mined.

Jan 1, 1923

By Paul M. Tyler, Herbert R. Mosley

Strategically situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority&apos;s research program has led to quasicommer-cia1 operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennessee&apos;s phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1. 1938, was approximately 19,000,000 tons. Offcial estimates of reserves are overly conservative and evidence submitted before a joint Congressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1942

By Herbert R. Mosley, Paul M. Tyler

Strategically situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority&apos;s research program has led to quasicommer-cia1 operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennessee&apos;s phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1. 1938, was approximately 19,000,000 tons. Offcial estimates of reserves are overly conservative and evidence submitted before a joint Congressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1942

By S. G. Bankoff

INCE1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. [ ] In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (-200 mesh) and 50 c.c. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments [c] through g are more insoluble than lead carbonate, therefore should prevent the formation of lead carbonate on the galena surface. In experiment [i] the calcium oxalate, which presumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments [j] through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1941

By S.G. Bankoff

Ince1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (—200 mesh) and 50 C.C. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments c through g are more insoluble than lead carbonate, there- fore should prevent the formation of lead carbonate on the galena surface. In experiment i the calcium oxalate, which precumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments j through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1943

By S. G. Bankoff

Ince1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (—200 mesh) and 50 C.C. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments c through g are more insoluble than lead carbonate, there- fore should prevent the formation of lead carbonate on the galena surface. In experiment i the calcium oxalate, which precumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments j through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1943

By S Bankoff

INCE1 proposed that electrostatic attraction between oppositely charged particles was responsible for slime-coating. Del Giudice2 postulated the metathetic formation of a cementing compound. Wark3 suggested that prevention of slime-coating was related to peptization of the slime. [ ] In the experiments of Table I the technique employed was essentially that of del Giudice, with the difference that the particle was examined under a film of water rather than dry.4 In general, the polished particle was agitated for 2 min. in a pulp consisting of 12.5 grams of the slime (-200 mesh) and 50 c.c. of distilled water, washed in three baths of distilled water, and examined at 220 diameters with the Leitz Ultropak. Observations of Brownian movement were made at 850 diameters with dark-field illumination. Several of these experiments do not jibe with the metathesis theory. According to published solubilities,5,6 the lead salts of the anions in experiments c through g are more insoluble than lead carbonate, there- [ ] fore should prevent the formation of lead carbonate on the galena surface. In experiment i the calcium oxalate, which presumably was on the calcite surfaces, should have permitted the formation of a lead carbonate cement by virtue of its greater solubility. Experiments j through m show that the addition of lime accelerates the deposition of quartz onto a galena surface. The writer is unable to postulate a satisfactory cementing compound, according to the metathesis theory, to explain this effect. These experiments led to the conclusion that the metathetic formation of a cement-

Jan 1, 1941

By Werner Langguth

The modern process and plant for the precipitation of gold from chlorine solutions, by sulphurous acid gas and hydrogen sulphide, differ materially from the older methods of precipitating with sulphate of iron. The chemical process and its applicability, as carried out in the Golden Reward chlorination-works at Deadwood, S. D., was described and discussed in the Engineering and Mining Journal, of New York, for February 14, and March 21, 1891. I purpose to give, in this paper, the details of construction from a general standpoint—the particular arrangement, most suitable to each case, depending, of course, upon local conditions. The accompanying sketch shows the arrangement. The plant consists of a wooden, lead-lined tank, in which the chlorine solution is precipitated; apparatus for the production of the precipitants, sulphurous acid and hydrogen sulphide; and a pressure-tank and filter-press for the collection and filtration of the precipitated gold-sulphides. These parts and arrangements are, in general, those which I employed in the Deadwood chlorinationworks, and which have proved practically successful, more than $100,000 worth of gold having been already precipitated by this method. In the construction of the generator and pressure-tank I have made, however, a few slight changes. 1. The Precipitating-Tank. The exact dimensions of this tank are not of much importance. A horizontal area of 10 x 12 feet and a height of 12 feet, holding about 7000 gallons of solution, is a good size. As the amount of attention and care required to precipitate the solution in a precipitatingtank is independent of the size of the vessel, there is economy in tanks of large capacity. Square tanks are more advantageous than round ones, because they need less floor-space, and at the same time are cheaper in construction. These tanks are made of common 2inch pine boards and 12 x 12-inch timber. They are well-bolted,

Jan 1, 1893

By L. Wahl, M. Allard, B. Trentini

REMOVAL of sulfur in steelmaking is presently a problem of utmost importance as requirements on final sulfur contents in finished steels become increasingly strict. This is in spite of often increased sulfur contents in the fuels used during the different stages of steel processing. According to local conditions or current economic factors, sulfur can be removed during one or more of the processing operations; for instance, in a blast furnace operated under high temperatures and with a high slag basicity ratio and also by means of high inputs of manganese into the burden. These methods of proceeding are, however, expensive and in contradiction with the acid practice which is gradually being developed owing to the fact that it allows coke and lime savings and usually permits an increase of productivity. In the melting-shop, desulfurization can proceed in the open-hearth or electric furnace with one or several very basic slags, or with special prefused slags (Perrin process) mixed with steels poured from the open-hearth, electric furnace, or converter. Liquid pig iron has also been treated separately before being used in the melting shop, in order to reduce high sulfur contents. This external desul-furization has been developed in Europe for the basic Bessemer Thomas process, which is again in favor owing to the great flexibility of such installations and to the fact that the steel produced is not polluted by impurities coming from the scrap. Since the basic Bessemer process, as usually practiced, has a low desulfurizing power, external desulfurization is generally carried out in ladles by means of alkalies such as soda ash. This method, which has the advantage of being simple and costing little, has only a medium desulfurizing power, which implies the necessity for repeating the operation several times when a substantial amount of sulfur has to be removed or when very low sulfur contents are desired. Thermal losses are high and there is a considerable decrease in output. Moreover, the resulting fluid and corrosive slag, which is extremely difficult to eliminate, attacks the refractory linings of the mixers and steel furnaces. Therefore, it seems necessary to devise a simple method for external desulfurization which would not only remove substantial quantities of sulfur from the hot metal coming from an acid blast furnace, but which would also bring the sulfur contents down to the low level required in the making of high quality steel and iron. Principle of the Process In this paper a new method will be described for desulfurizing hot metal. It has been perfected by

Jan 1, 1958

By R. H. Heyer, J. L. Bray, M. E. Carruthers

It is well known that iron markedly improves the physical properties and casting characteristics of aluminum bronzes. The use of 1 to 4 per cent iron as the principal modifying addition has become common practice in many foundries melting aluminum bronzes. Although the beneficial effects of iron are unquestioned, there is some uncertainty regarding the structural changes caused by it in the basic copper-aluminum system. It is agreed that a new constituent appears in abundance when the iron content reaches 2 to 4 per cent. This constituent, which frequently occurs in shapes resembling clover leaves, is sometimes assumed to be an aluminum-iron intermetallic compound. If this were correct we might expect a change in the structural relationships of the matrix in the direction of decreased aluminum content. On the other hand, it has been reported that iron has a negligible effect in altering the fundamental relationships of copper-aluminum alloys1 Others2&apos;3 have reported an additive coefficient. Apparently it will be necessary to know the equilibrium relationships between the phases of the copper-aluminum-iron alloy system to establish any such theory as fact. When this has been done it may very well be that a further revision in the structural relationships may be necessary to describe the changes to be expected in commercial cast alloys. It was with this latter problem before them that the authors attempted to determine the change in the copper-aluminum relations with respect to iron. Objects of the Investigation In certain investigations carried out by the authors for a plant producing a large tonnage of cast aluminum bronzes the structures

Jan 1, 1936

By R. V. Smith, E. J. Dewees, R. H. Williams

Before this paper was presented, the terms "f" and "v1/f in flow equations had been called "friction coefficient" and "friction factor," respectively. However, many authors have used the names for the terms interchangeably, with the result that considerable confusion has existed in the literature on flow of fluids. In an effort to establish a clear and concise terminology for these terms, the authors have designated f as "resistance coefficient" and dm as "transmission factor." Transmission factors for the flow strings of gas wells were determined by tests on wells in six fields of Oklahoma, Texas, and Louisiana. Data were collected on 14 gas wells while gas was flowing through 1 1/4, 2, 21/2, and 3-in. tubing and 51/2 and 7-in. casing. The transmission factors developed from these data were found to follow the resistance equation published by Nikuradse1 for turbulent flow in "rough" pipes with an average absolute roughness of 0.000,65 in. This average absolute roughness is believed to be representative generally of the flow strings of gas wells with the exception of those that have been exposed to corrosion or other conditions causing undue roughness. Also, use of an absolute roughness of 0.000,65 in. probably will result in transmission factors that are more representative of gas-well conditions than those in common use today, provided that the transmission factors are calculated by the methods outlined in this report. The authors believe that use of these transmission factors will permit calculation of more accurate subsurface pressures in gas wells than those in use today. Engineers use transmission factors in flow equations to compute subsurface pressures in flowing gas wells from measured wellhead pressures. These subsurface pressures are necessary for determining the productivity of gas wells from "back-pressure" tests. The methods of calculating pressures in flowing gas wells, as outlined by Rawlins and Schellhardt2 in Bureau of Mines Monograph 7, are based on the transmission factors in the well-known Weymouth formula" Natural gas engineers have realized that errors introduced by using transmission factors as given by the Weymouth formula are relatively unimportant in testing low-capacity gas wells; but they also know that such factors are important considerations in testing large-capacity wells. Accordingly, the research described in this report was undertaken to fulfill the need for more accurate means of calculating subsurface pressures in gas wells. This report is part of the Bureau&apos;s study of the flow of natural gas through pipe and commercial pipelines. Several of the conclusions regarding flow in the flow strings of gas wells were influenced by the results of the study of flow in horizontal pipelines. These instances are mentioned in the text of this report. METHODS OF COMPUTING TRANSMISSION FACTORS Methods and procedures for computing transmission factors for turbulent flow in circular pipes from test data taken on gas wells have been derived and explained in detail in a paper by Smith4. As these methods were used to calculate the transmission factors presented in this report, a summary is included. Starting with

Jan 1, 1955

By Vard H. Johnson

IN 1943 the U. S. Bureau of Mines undertook drilling in an effort to develop new reserves of coking coal in an area near Paonia, Colo., as a part of an attempt to alleviate the shortage of known coking coal of good quality in the western United States. Geologic mapping of the area was undertaken by the U. S. Geological Survey with the purpose of first furnishing guidance in location of drillholes and later aiding in interpreting the results of the drilling. The drilling program was under the general supervision of A. L. Toenges of the U. S. Bureau of Mines. J. J. Dowd and R. G. Travis were in charge of the work in the field. Geologic mapping was started by D. A. Andrews of the Geological Survey in the summer of 1943 and was continued from the spring of 1944 to 1949 by the writer. The first few holes drilled failed to locate coking coal, but in the summer of 1944 coking coal was discovered by drilling 6 miles east of Somerset, Colo., the site of present mining. In the succeeding years, 1945 to 1948, 100 to 150 million tons of coal suitable for coking were blocked out by drilling. The ensuing discussion of the geologic controls on the distribution of coking coal in the area is based on the geologic mapping as well as the drilling done in the Paonia area, more complete descriptions of which have appeared or are in process of publication."&apos; In order that the possible geologic controls affecting the present distribution of coking coal may be considered, it is necessary to discuss briefly the indicators of coking quality coals. Coking Coal Coal that cokes has the property of softening to form a pastelike mass at high temperatures under reducing conditions in the coke oven. This softening is accompanied by the release of the volatile constituents as bubbles of gas. After release of the contained gases and upon cooling, a hard gray coherent but spongelike mass remains that is referred to as coke. This substance varies greatly in physical properties and, to be suitable for industrial use, must be sufficiently dense and strong to withstand the crushing pressure of heavy furnace loads. Western coals have a generally high volatile content and therefore form a satisfactory coke only when they attain a rather high fluidity during the process of heating arid distillation in the coke oven. When this high degree of fluidity is developed, the volatile constituents escape and leave a finely porous coke. On the other hand, when the degree of fluidity is low the product is an excessively porous and therefore physically weak mass that is called char." Small quantities of oxygen present in coal are believed to decrease the fluidity of the material during the coking process and to favor the development of char rather than coke. In consequence, coal chemists have for some time considered the possibility of developing an index to coking qualities by inspection of chemical analyses of coals.&apos; A formula has now been developed that does permit a rough preliminary estimate of the cokability of coal on the basis of the analysis on an ash and moisture-free basis. Coals may be eliminated as possible coking fuels if the oxygen content is greater than 11 pct. Similarly the ratio of hydrogen to oxygen must be greater than 0.5 and the ratio of fixed carbon to volatile constituents must be greater than 1.3. If the coal, on the basis of these limiting factors, appears to have possible coking qualities, the following formula permits determination of the coking index: a+b+c+d Coking index = -------- 5 a equals 22/oxygen content on ash and moisture-free basis, b equals two times the hydrogen content divided by oxygen content on moisture and ash-free basis, c equals fixed carbon/l.3 x volatile matter, and d equals the heating value on moist, ash-free basis/13,600. Coking indices higher than 1.0 suggest that the coal will coke, and indices above&apos; 1.1 indicate good coking tendencies. Although generally usable, this formula &apos;is not completely satisfactory because the percentage of oxygen shown in ultimate analyses is derived only by difference; i.e., by subtracting the sum of the percentages of the constituents determined analytically from 100 pct. Although the coking index indicates the coking tendencies of coal, it is necessary to make physical tests of coke before its industrial value can be determined. The U. S. Bureau of Mines has developed a standard procedure for determining the approximate strength of coke that would be formed from a given coal. In this test one part of ground coal, mixed with 15 parts of carborundum, is baked to form a standard briquette. The weight, in kilograms, necessary to crush the briquette is termed the agglutinating index. This test determines the relative fluidity attained in the coking process by measuring the cementing strength of the coal in the briquette. A

Jan 1, 1953

By Vard H. Johnson

IN 1943 the U. S. Bureau of Mines undertook drilling in an effort to develop new reserves of coking coal in an area near Paonia, Colo., as a part of an attempt to alleviate the shortage of known coking coal of good quality in the western United States. Geologic mapping of the area was undertaken by the U. S. Geological Survey with the purpose of first furnishing guidance in location of drillholes and later aiding in interpreting the results of the drilling. The drilling program was under the general supervision of A. L. Toenges of the U. S. Bureau of Mines. J. J. Dowd and R. G. Travis were in charge of the work in the field. Geologic mapping was started by D. A. Andrews of the Geological Survey in the summer of 1943 and was continued from the spring of 1944 to 1949 by the writer. The first few holes drilled failed to locate coking coal, but in the summer of 1944 coking coal was discovered by drilling 6 miles east of Somerset, Colo., the site of present mining. In the succeeding years, 1945 to 1948, 100 to 150 million tons of coal suitable for coking were blocked out by drilling. The ensuing discussion of the geologic controls on the distribution of coking coal in the area is based on the geologic mapping as well as the drilling done in the Paonia area, more complete descriptions of which have appeared or are in process of publication."&apos; In order that the possible geologic controls affecting the present distribution of coking coal may be considered, it is necessary to discuss briefly the indicators of coking quality coals. Coking Coal Coal that cokes has the property of softening to form a pastelike mass at high temperatures under reducing conditions in the coke oven. This softening is accompanied by the release of the volatile constituents as bubbles of gas. After release of the contained gases and upon cooling, a hard gray coherent but spongelike mass remains that is referred to as coke. This substance varies greatly in physical properties and, to be suitable for industrial use, must be sufficiently dense and strong to withstand the crushing pressure of heavy furnace loads. Western coals have a generally high volatile content and therefore form a satisfactory coke only when they attain a rather high fluidity during the process of heating arid distillation in the coke oven. When this high degree of fluidity is developed, the volatile constituents escape and leave a finely porous coke. On the other hand, when the degree of fluidity is low the product is an excessively porous and therefore physically weak mass that is called char." Small quantities of oxygen present in coal are believed to decrease the fluidity of the material during the coking process and to favor the development of char rather than coke. In consequence, coal chemists have for some time considered the possibility of developing an index to coking qualities by inspection of chemical analyses of coals.&apos; A formula has now been developed that does permit a rough preliminary estimate of the cokability of coal on the basis of the analysis on an ash and moisture-free basis. Coals may be eliminated as possible coking fuels if the oxygen content is greater than 11 pct. Similarly the ratio of hydrogen to oxygen must be greater than 0.5 and the ratio of fixed carbon to volatile constituents must be greater than 1.3. If the coal, on the basis of these limiting factors, appears to have possible coking qualities, the following formula permits determination of the coking index: a+b+c+d Coking index = -------- 5 a equals 22/oxygen content on ash and moisture-free basis, b equals two times the hydrogen content divided by oxygen content on moisture and ash-free basis, c equals fixed carbon/l.3 x volatile matter, and d equals the heating value on moist, ash-free basis/13,600. Coking indices higher than 1.0 suggest that the coal will coke, and indices above&apos; 1.1 indicate good coking tendencies. Although generally usable, this formula &apos;is not completely satisfactory because the percentage of oxygen shown in ultimate analyses is derived only by difference; i.e., by subtracting the sum of the percentages of the constituents determined analytically from 100 pct. Although the coking index indicates the coking tendencies of coal, it is necessary to make physical tests of coke before its industrial value can be determined. The U. S. Bureau of Mines has developed a standard procedure for determining the approximate strength of coke that would be formed from a given coal. In this test one part of ground coal, mixed with 15 parts of carborundum, is baked to form a standard briquette. The weight, in kilograms, necessary to crush the briquette is termed the agglutinating index. This test determines the relative fluidity attained in the coking process by measuring the cementing strength of the coal in the briquette. A

Jan 1, 1953

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low, a medium, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0% ash, as follows: from low-volatile anthracite, 0.7%; from medium-volatile coal, 1.0%; and from high-volatile coal, 2.3%. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0% or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a convc.ntiona1 dense-media washing plant. Anthracite preparation practices during much of the industry&apos;s history were geared to maximum recovery of the larger sizes, pea through egg, which were used in hand-fired, domestic furnaces. Those sizes were cleaned to meet trade requirements, and the smaller sizes were usually higher in ash content. The impression, thus, was that ash content of anthracite always increased as the sizes got smaller. It was presumed that it was impossible to wash the finer sizes to extremely low ash contents. Following World War 11, the classical domestic market began to decline and the finer sizes assumed an increasingly large share of the market. For example, in 1949l 61% of the production was still pea and larger. Fig. l2 shows that -by 1955 these sizes accounted for only 50%, and in 1965, they were only 39% of the total anthracite produced. With the reduction in the market, increased quality was demanded, especially in export markets, and an increasing number of dense-media magnetite washers were installed in new and existing cleaning plants. In 1965, the coarse coal prepared at 59 breakers in the anthracite fields was sampled by the U.S. Bureau of Mines (USBM); approximately 50% of these plants were equipped with dense-media magnetite washers.3 Since 1950, more attention has been focused on the use of finer sizes for numerous industrial uses, including iron-ore sintering, pelletizing, foundry coke-making, cement manufacture, production of calcium carbide, and of carbon electrodes, etc. Most industrial uses require relatively clean anthracite, such as 10 to 11% ash for sintering and foundry coke, 7% for aluminum melting-pot cathode carbon, and 5% for carbide production. Hence, cleaning methods have been improved to the extent that dense-media washers, hydraulic cyclones, and flotation cells have been introduced as fine-coal-cleaning devices. It is now possible to wash the buckwheat, rice, and barley sizes (9116 X 3132-in.) to ash contents as low as 8 to 10% in dense-media devices, but washing the -3132-in. sizes to those limits presents more difficult problems, due mainly to the fineness of the material. This USBM investigation was conducted to determine the amount and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. The goal was to reduce the ash content to a level acceptable for industrial carbon uses, including electrode manufacture, which generally requires an ash content of 1% or less. While low-ash content is of primary importance in selecting industrial carbons, the amounts of other constituents are also important, including iron, silicon, titanium, nickel, vanadium, and sulfur. They were not considered in this work, since their occurrence in deashed anthracite has been studied elsewhere.4 The results of the present investigation were used to design a flowsheet, suggesting a method for producing ultraclean anthracite as part of conventional preparation practice, using dense-media vessels, crushers, pulverizers,

Jan 1, 1970