Search Documents

By J. van Lookeren

In the case of a reservoir where the oil underlies a large gas cap and overlies bottom water, production can be inzproved considerably if wells are perforated below the water-oil contact rather than opposite the oil-bearing section. The theoretical arguments for this improvement, which in some cases may be tenfold, are supported by experimental evidence. INTRODUCTION Reservoirs frequently consist of one sand body containing an oil layer underlying a thick, gas-bearing section and overlying bottom water (Fig. 1). Wells in such reservoirs are customarily opened up opposite the oil-bearing interval or, rather, opposite the lower part of this interval (Fig. 2). More often than not, it is inefficient or prohibited to blow off large quantities of gas with the oil. This im-psses a severe limitation on the drawdown, which results in low oil-production rates. Because of the small difference in specific gravity between oil and water, the latter will easily cone upwards, so that the production of water together with the oil is not prevented by this completion method. In such a situation wells should be opened deeper, in the originally water-bearing zone. The gas can be shut off by not perforating over the upper part of the interval (Fig. 3) or by a tubing hung close to the bottom of the interval (Fig. 4). Initially much water will be produced, but when steady-state conditions have been established (as depicted in Figs. 3 and 4) larger drawdowns are permissible than in a conventionally completed well, and correspondingly higher oil-production rates will result. Water cuts are only slightly higher because of the small effect of gravity on the water-oil flow distribution. CALCULATIONS The ratio of improvement has been estimated by means of approximate calculations. The completion depicted in Fig. 4 is the most convenient basis for these calculations. By postulating that vertical flow gradients can be disregarded, the Appendix shows that the well-known Dupuit formula can be obtained except for some complication due to the presence of two fluids rather than one. The Appendix makes the reasonable assumption that, for suitable boundary conditions, the oil layer occupies a constant fraction of the total fluid height throughout the reservoir. The oil- and water-production rates can thus be related to the liquid levels in the borehole as follows:

Jan 1, 1966

By R. C. Troxell, S. C. Sun

EFFORTS to obtain definite quantitative data when employing the currently used bubble pick-up method1,2 as a pre-flotation investigation tool led to the adoption of the magnifying mirror method and the microscopic method modifications. Quantitative data obtained by these two methods were converted into bubble pick-up indices and bubble pick-up coefficients. Rough correlations were established between the calculated indices and the results of contact angle testing as well as actual flotation under the same conditions. The basic steps of the magnifying mirror method are as follows: 1—mixing 200 ml distilled water, sized and cleaned mineral particles of approximately 0.5 g, pH regulator, and flotation reagents in a glass beaker; 2—swirling the mineral particles to the center of the beaker to leave a clear circumference; 3—pressing an air bubble against the mineral particles for about 1 sec, and then moving the mineralized air bubble to the clear part of the beaker; and 4—dropping all the attached mineral particles of the air bubble by tapping the bubble holder, and counting the number of the dropped particles by looking at the magnified image in the mirror positioned beneath the beaker. This method is impractical for mineral particles which are transparent in water or finer than 200 mesh. The microscopic method is essentially similar to the above described magnifying mirror method, with the exception that the mineralized air bubble was drawn up into the bubble holder and subsequently discharged onto an externally placed watch glass, where the number of pick-up particles was counted with the aid of a microscope or hand lens. Drying was necessary when the discharged liquid interfered with the counting. The results of the bubble pick-up tests can be simply expressed in the form of the actual count. However, this can be misleading because the number of pick-up particles varies not only with the size of bubble but also with the size of particles. This short-coming is largely remedied by the use of the bubble pick-up index. as calculated from the following equation: PI = (pn/p) 100 [1] in which PI and pn are respectively the pick-up index and the number of pick-up particles under any test conditions, and p is the maximum number of pick-up particles of the same mineral under optimum flotation conditions, with the same size holder and particle. The bubble pick-up coefficient is a term coined to denote the difference between the bubble pick-up index of mineral particles in a liquid and that of the same mineral-liquid mixture plus a chemical reagent at the same pH value. For example, the difference between the pick-up index of a naturally floatable bituminous coal in a solution of water and kerosene and that of the same coal in water alone is a bubble pick-up coefficient. Compared with the contact angle method, the quantitative bubble pick-up method is inferior in accuracy but superior in sensitivity. Other advantages of the bubble pick-up method are that the apparatus can be easily assembled, the mineral sample is conventionally prepared, and the test procedure is relatively simple. References S. R. B. Cooke: The Flotation of Quartz Using Calcium Ion As Activator, Trans. AIME (1949) 184, p. 306. 'G. A. Last and M. A. Cook: Theory of Collector-Depressant Equilibrium at Mineral Surfaces. Paper presented at St. Louis Meeting, AIME (February, 1951).

Jan 1, 1954

Jan 1, 1967

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10, 1916 to Nov. 10, 1916. ANCHOR, HANS C., Supt., Dome Extension Mines Co., Ltd., South Porcupine, Ont., Canada. BABCOCK, EARLE J., Dean, College Of Min. Engrg., State Univ. Of N. Dak., Grand Forks, N. Dak. BIDDIS0N, P. McDONALD, Construction Engr., The Ohio Fuel Supply Co., 52 W. Gay St., Columbus, 0. BOISE, PAUL T., Asst. Mgr., Stimpson Equipment Co., Felt Bldg., Salt Lake City, Utah. BOURNE, RALPH H., Vice-Pres Whiting Foundry Equipment Co., Harvey, Ill. BROWN, EDWARD OTTO FORSTER, Min. Engr., 706-707 Salisbury House, London, E. C., England.

Jan 12, 1916

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By B. D. Lichter

In a previous paper, Oelsen, Schuermann, and Hey-nertl pointed out the possibility of obtaining complete thermodynamic functions for alloy systems from calorimetric measurements alone. Specifically, if the heat content of a heterogeneous, multicomponent system is known as a function of temperature and composition, then it is possible to derive the heats, entropies, and free energies of formation of liquid phases and of solid intermediate phases of fixed composition. The authors present equations and graphical techniques applicable to eutectic systems and systems with intermediate phases without solid solubility at lower temperatures. eijering has considered possible extension of the treatment to systems with complete solid-state miscibility at lower temperatures; however, experimental difficulties practically restrict the method to systems with very limited miscibility in the solid state. The purpose of this note is to present an alternative derivation of the heats and entropies of formation of liquid phases and of solid intermediate phases from heat-content measurements alone. Fig. 1 shows three types of phase diagram to which the analysis may be applied. If the heat content is determined as a function of composition x, at temperature T, we have quite generally and the heat of mixing of the liquid is obtained directly from heat-content measurements. If the temperature T lies in a two-phase region (solid-liquid) then

Jan 1, 1967

Coal production during 1963 amounted to 446 mil- lion tons, an anticipated increase of about 6% over the 1962 production of 422 million tons. Electric consumption was 207 million tons, a continuation of its upward trend with an increase of about 7%. The metallurgical market consumed 77 million tons: the industrial market, 96 million tons; and the retail market, 26 million tons. Exports were 46 million tons. Modernization continues in the coal industry as it approaches the mid-1960's. The industry has shown a keen desire to explore and pursue new developments, new concepts and new managerial methods and techniques that have become so vital and important for industrial well-being.

Jan 2, 1964

By H. O. Hofman

At the Lake Superior meeting, September, 1904, Messrs. A. Gibb and R. C. Philp presented a paper entitled " The Constitution of Mattes Produced in Copper-Smelting,"' in which they concluded that ferrous and cuprous sulphides formed the chemical compound, 5 Cu2S, FeS. They arrived at this inference from the observed fact that a matte containing Cu,S, 90.4, and FcS, 9.6 per cent. (or, in round figures, Cu2S, 90, and FeS, 10 per cent.), did not contain any metallic copper, while one with more than 10 per cent. of FeS readily dissolved copper, and with less than this amount retained copper in mechanical suspension. Although they determined the melting-points of five mattes containing from 32.6 to 80.1 per cent. of copper, they did not draw a freezing-point curve, as the necessary apparatus was not available. A microscopical examination of 11 polished samples gave them a grayish-black field of very uniform appearance, except that five of the specimens showed the presence of metallic copper. The object of the present investigation was to supplement the above paper by drawing the freezing-point curve of the ferrous sulphide-cuprous sulphide series, and to see how the constitution could be further revealed by microscopical work. The results obtained lead to conclusions very different from those of Gibb and Philp. While their paper bears the date 1904, it was published only in 1906.2 In the meantime, Bolles3 had presented his paper, " The Concentration of Gold and Silver in Iron-Bottoms." The raw material which formed the basis of the research was a matte containing Fe, 61.68, and Cu, 11.20

Jan 1, 1908

By Homer S. Frankhouser

Materials may be dredged, processed, stored and loaded for shipment at a single site in water depths ranging from 250 to 1200 ft. Solution mining may also be accomplished in deep sea situations. And, open air subsea mines with direct surface access may be developed and worked under the ocean floor. These concepts for deep sea mining are the results of extensive testing of individual components of the proposed systems by Dravo Ocean Structures, Inc., a subsidiary of Dravo Corp. A basic structure in these systems is the articulated platform. The platform consists of a gravity- type base and a buoyant cylindrical column which is constructed at an onshore location, towed to the offshore site and installed in a matter of days without use of heavy equipment. The base is also buoyant for towing purposes. This allows for gradual flooding to the point of negative buoyancy for positioning and anchoring to the ocean floor.

Jan 1, 1971

By F. W. Schaller

TETRAGONALITY is an important aspect of the models of transformation, strengthening, and tempering of ferrous martensite. When the c/a

Jan 1, 1963

By C. F., Christopher

The purpose of any steel-making process is to convert the two raw materials iron and scrap into steel. The chemical analysis of the steel is set within certain limits which involve the physical proper- ties desired by the consumer. In addition to tensile properties a large number of other properties are at the present time desired, such as impact resistance, grain size regulation, specific degrees of hardenability, resistance to creep at high temperatures, resistance to expansion on heat treatment, the ability of the product to undergo extreme amounts of cold deformation without failure, and many other properties which are not directly related to the specified chemical analysis. Variations in many of the properties of plain-carbon steels are due to elements and compounds not included in the ordinary "five element"§ composition. Such variations result primarily from variations in oxidation of the metal in the furnace and from the deoxidation method employed. The steel-making problem therefore resolves itself into two distinct sections: (I) the elimination of certain elements from the charge (the iron and scrap entering the furnace) and the addition of materials to meet the chemical specifications for the heat; (2) the manipulation of the slag and metal and the process of deoxidation to give certain desired properties in the steel entirely apart from the chemical analysis specified. Each of 'these two ends must be attained

Jan 1, 1957

Jan 1, 1967

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector's item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy's slate left most classrooms before the oldest of us were born.

Jan 9, 1964

By Nelson P. Hulst

COMMITTEES. DULUTH.-Nelson P. Hulst, Chairman; J. B. Adams, W. C. Agnew, M. H. Alworth, C. W. Andrews, R. Angst, William R. Appleby, C. E. Bailey, G. G. Barnum, E. F. Bradt, Mylie Bunnell, George L. Cheesebrough, Peter Christen¬sen, F. A. Cokefair, T. F. Cole, C. A. Congdon, N. Cowling, George H. Crosby, M. D. Cullum, C. d'Autremont, Jr., H. L. Dresser, C. T. Fairbairn. Walter Fitch, F. L. Gilbert, J. T. Hale, G. G. Hartley, E. B. Hawkins, M. S. Hawkins, J. H. Hearding, Louis Hill, L. J. Hopkins, F. E. House, J. C. Hunter, 0. D. Kinney, J. W. Kreitter, E. J. Longyear, Alexander McDougal, W. A. McGonagle, A. M. Marshall, W. N. Merriam, T. D. Merrill, John Millan, P. Mitchell, Clarence Moore, Hon. Page Morris, C. H. Munger, Henry Nolte, W. J. Olcott, A. L. Ordean, Thomas Owens, F. A. Patrick, H. M. Peyton; D. M. Philbin, Capt. Charles Potter (U. S. A.), L. W. Powell, Harry Roberts, Louis Rouchleau, George A. St. Clair, J. U. Sebenius, Joseph Sellwood, Amos Shepherd, W. B. Silvey, George Spencer, George C. Stone, H. B. Sturtevant, George D. Swift, Kirby Thomas, C. D. Thompson, A. D. Thomson, G. A. Tomlinson, Charles Trezona, R. R. Trezona, Maj. J. H. Upham, Charles Van Barneveld, W. W. Walker, J. L. Washburn, A. C. Weirs, H. J. Wessinger, A. B. Wolvin, Dwight E. Woodbridge. HOUGHTON.-W. E. Parnall, Chairman; W. D. Calverley, Secretary; W. B. Anderson, L. S. Austin, Jacob Baer, William Bath, F. J. Bawden., Simon Beahan, John Been, C. H. Benedict, Walter Bloomfield, S. H. Brady, Samuel Brady, Henry Brett, A. L. Burgan, F. I. Cairns, W. H. Cake, Arthur L. Carnahan, William Carpenter, Phillip Carroll, John J. Case, T. L. Chadbourne, W. A. Childs, B. F. Chynoweth, Captain James Chynoweth, H. P. Clausen, F. G. Coggin, H. D. Conant, J. B. Cooper, J. R. Cooper, John Cuddihy, Thomas Cummings, Robert Davidson, J. B. Dee, J. R. Dee, T. S. Dee, Theodore Dengler, M. M. Dennis, Captain Thomas Dennis,. F. W. Denton, A. D. Edwards, R. M. Edwards, C. S. Fales, Daniel Fisher, Henry Fisher, James Fisher, A. L. Floeter, Frank H. Getchell, M. C. Getchell, W. M. Gibson, W. M. Gilliland, James G. Glanville, George Goodale, H. S. Goodell, A. R. Gray, Edward Grierson, Homer Guck, H. D. Haddock, Captain Josiah Hall, John L. Harris, Captain S. B. Har¬ris, Enos Harrold, F. William Hartmann, George L. Heath, C. M. Hoar, Thomas Hoatson, 0. P. Hood, Captain Thomas Hooper, Captain Joshua D. Husking, Dr. L. L. Hubbard, Arno Jaelinig, E. D. Johnson, G. A. Koenig, Edward Koepel, C. H. Krause, R. H. Leach, A. W. Leonard, James MacNaughton, Edward McCormick, Thomas McDonald, R. T. McKeever, F. W. McNair, James McRae, John Mackey, John C. Mann, Major G. A. Marr, Captain Thomas Maslin, Harry Mercer, James Merton, Michael Messner, William F. Miller, Captain J. Milligan, Dr. J. W. Moore, Charles H. Moss, H. F. Nickerson, Charles L. Noetzel, P. H. Paine, John Penrose, Captain John Pentecost, Graham Pope, R. C. Pryor, James Ramsay, J. T. Reeder, Allen F. Rees, J. H. Rice, W. G. Rice, James

Jan 1, 1905

By Chung Yu, Wang

CHINA can he roughly divided into three metallogenetic province: North China, the Yangtze Valley, and South China. In North China the old Pre-Cambrian schists and gneisses are represented by the abundance of quartz mines in which sporadic occurrences of copper, lead, zinc, gold, and silver are sometimes found in subordinate quantities. Along the Yangtze Valley and in Central China, extending eastward as far as Shantung, are found here and there intrusions of dioritic rocks, in which occur the famous contact deposits of iron ore, besides which minor quantities of copper. lead, and zinc are also found. In South China the igneous intrunsions are of granitoid type in which, or in the vicinity of which, occur in certain regions immense deposits of antimony, tungsten, tin, and mercury. Broadly speaking. most of the famous coal mines are now situated in regions north of the Yangtze River, in which occur also the sedimentary deposits of iron in contradistinction to the contact deposits of iron along the Yangtze Valley.

Jan 1, 1943

By J. Gordon Parr, D. H. Polonis

IN a previous study of hypereutectoid Ti-Ni alloys' a substructure was observed in quenched powder specimens when the constitution was 100 pet retained ß body-centered-cubic phase. The alloy powders were quenched from 1000°C by a blast of helium gas and precautions already described were observed throughout the work, to minimize contamination. Ogden et al.2 have previously observed subboundaries in the ß phase of a Ti-Mn-N alloy; but this structure was attributed to nitrogen-rich a precipitation. The nitrogen content of the Ti-Ni alloys does not exceed 0.02 pet and the quenching rate was sufficiently rapid to suppress precipitation reactions. Since X-ray diffraction results have confirmed the absence of any second phase which might account for this phenomenon, it seems unlikely that this substructure is explicable in terms of nitrogen content. Fig. 1 shows the substructure in adjacent grains of 100 pet ß phase in a quenched 6 atomic pet Ni alloy. Fig. 2 shows adjacent ß grains in a similarly treated alloy; one grain contains marked intracrys-talline boundaries and the other is completely free from any substructure. The suberystals appear to have fairly regular shapes, suggesting a regular orientation relationship among them. Tempering the retained ß structure at temperatures below the eutectoid eliminates the substructure at an early stage of ß decomposition. At the present time it is possible only to guess at an explanation for this subboundary phenomenon, since very little work has been reported on substructures resulting from phase changes. It is believed that the present phenomenon is due to poly-gonization resulting from unrelieved stresses set up

Jan 1, 1957

Carlisle: An old friend and good friend, Alan Bateman, is the Silliman Professor of Geology Emeritus at Yale and editor of the Journal of Economic Geology. Now, Alan, let's start off by telling us something about how you became interested in copper. Bateman: Well, after I left Yale in 1913, I was appointed one of the field members of the Secondary Enrichment Investigation. We spent three years in the field studying all the copper deposits of North America, trying to find out how secondary copper enrichment took place. As part of this investigation, I went up to Kennecott, Alaska, in 1916. After the trip I was asked by the president of the company to become consulting geologist to them. I accepted his offer, and to this day I'm still consulting geologist to the Kennecott Copper Corp. Up at Kennecott, there were both Henry Krumb and my good friend Henry DeWitt Smith, who was general superintendent. He and I had been together at Yale, and I had ushered at his wedding. Interestingly enough, Henry took his bride to Alaska and I took mine there two months later. My assistant was Don McLaughlin, and I think that was his first experience in a mining camp. We published a paper on Kennecott together and cemented a friendship lasting to this day.

Jan 11, 1964

By Howard R. Pratt, Jimmie L. Bratton

The Air Force Weapons Laboratory (AFWL) has been carrying out a series of experiments whose principal purpose is to measure the dynamic response of rock media to large pressure pulses. Coupled with the field experiments have been theoretical calculations simulating this response. These two approaches allow an appraisal of the current ability to measure in-situ rock response under extreme conditions and also give a fair estimate of the current state-of-the-art in the area of computer calculation of the response of "real" geologic media to a large load. The area chosen for the test series is composed of a sequence of sedimentary units (shale, sandstone, and limestone) located in the Estancia Valley 45 miles east of Albuquerque, N.M. (Fig. 1). The units, which dip gently off the uplifted Manzano Mountains to the west, are essentially horizontal at the test site. An extensive geologic and geophysical investigation of the area was carried out in the form of surface mapping and seismic exploration. Numerous holes were cored and material properties were determined from tests of the cores. In-situ geophysical measure¬ments were also carried out. The experiment consisted of loading a 60X40 ft test area with a 4000-psi transient exponentially decaying pressure pulse. The pulse was initiated at one end and traveled the 60-ft length of the test bed. The test area was instrumented with acceleration, velocity, and strain measuring devices placed in drill holes to depths of 30 ft. Theoretical computer calculations of the response of the layered geologic media have been carried out on the AFWL CDC 6600 using one and

Jan 1, 1972

By OWEN H. PERRY

One of man's primary tools is the ordinary screen. Whether of mesh or punched plate, it is fundamental in principle, primitive in its origin, and common in its application through all the world; and yet the screen goes only a part of the way toward the completion of its job of separating materials according to size. It will give a practical and continuous separation according to "size," as generally understood (accurate according to the breadth), but the accurate and continuous separation as to thickness is not a practical function of the screen. Still, all through history, the thickness of particles of material must have been important to many people; therefore, one would expect that some standard method of sizing for thickness would long since have been evolved and that equipment applying that method would be readily available to any in¬dustry. This, however, seems not to be so.

Jan 1, 1949

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,1 later as agalmatolite,2 and finally as pyrophyllite,3 has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,4 which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments.

Jan 1, 1958