Search Documents

By J. L. Gregg

RECENTLY there has been considerable interest in the production and use of, extra hard alloys composed primarily of tungsten and carbon. Dr. Hoyt's recent paper1 gives a good description of these alloys and describes their performance when used as tools. There are a number of these alloys on the market sold under various trade names, and it is the purpose of this paper to describe the results of an investigation of the structure of five of these alloys by means of microscopic and X-ray methods. The samples studied were in the form of small tools or wire-drawing dies, which were either purchased or supplied as samples. They were in some cases not supplied by the original makers but were furnished by the agents in this country, and we wish to call attention to the fact that they may not be truly representative of the materials supplied under the various trade names. No performance data are given and no inference as to the inferiority of one alloy as against any other is made K Schröter2 recently described methods for polishing alloys of this type for microscopic examination and has presented photomicrographs of several alloys. However, he did not identify their constituents or describe methods for their identification.

Jan 1, 1929

By Gifford E. White

EXPLANATIONS of the basic procedure for making earth-conductivity studies by the Eltran method have already appeared in several places.1,2,3 In its essentials, this method consists of applying step functions of voltage to one pair of earth grounds and measuring the transient potential resulting at a separate pair of ground points. As previously pointed out,4 the transient potential resulting from a suddenly applied steady voltage is the indicial transfer function of Carson,5 which has been extensively studied in network theory. [ ] The discussion here, with one special exception, will ignore the problem of how the physical configuration of the earth affects the transient response voltage; it appears that this phase of the problem has been solved in only a few special cases having any direct bearing on the prospecting problem. Entirely distinct from the potential theory aspect of the conductivity problem is the interesting material that can be had from studying the well-known network relations between cause and effect in linear circuits, and thus deducing criteria for the application of the several experimental methods available. To do this, only one assumption need be made about the nature of the earth. The earth is to be considered a linear conductor within the tolerance of ordinary measurements. The discussion will be restricted to collinear electrode configuration like that of Fig. I, since this is the only type of spread practical for use with driving currents that vary with time. Here one pair of grounds carries the driving current, and in line with these and external to them is a [ ] pair of potential probes. The problem will be to consider the relation between the different voltages appearing between the potential circuit terminals when various types of driving voltage sources are inserted in the current circuit. Suppose that the grounding points G1 and G2 make good contact with the earth, and that a battery of sufficient voltage to produce one ampere of direct current is introduced into the current circuit by the closing of a switch. The potential transient response to such a voltage can be measured by taking an oscillogram at the potential circuit terminals, giving the time function that has been called A(t).4 This time function has been solved for analytically in the case of a homogeneous earth,6,7 and the

Jan 1, 1941

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.' The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

By Oscar Harder

IT is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing -his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treating high-speed steels. Regarding this research, Dr. Sauveur, (22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World's Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and. related materials in the red-heat range, using various methods. . The results, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as its immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

By Frank H. Macpherson

FEW people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war. The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,725 2 tons in the period 1931 to 1941. It became apparent early in the year 1941 that the United States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. As more than 95 per cent of the known bauxite reserves of the United States was in Arkansas, careful preliminary studies were made in that state by representatives of the United States Bureau of Mines, the United States Geological Survey and the War Production Board in the summer of 1941. Reserves in other states also Were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite-producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry Weight) set for Arkansas by the War Production Board Was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted, the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place

Jan 1, 1945

By A. L. Fentress, P. R. Bucky

The purpose of this paper is to present a scientific method for determining the proper span and shape of roof for safe and economical mining; at present, these two vital factors wherever pillars are left to support the roof are determined by local practice or general experience. To develop the method described here, experimental laboratory work was done. The arch adopted was a segment of a circle, a flat roof being considered an arch with an infinite radius. Hitherto, arches have been used underground without the background of stress analysis that generally precedes arch construction on the surface. In many cases results have not been as expected, because of the lack of knowledge of the factors affecting its strength and behavior. A theoretical and experimental study of arches should furnish information that will make it possible to design safe and economical surface structures as well as underground openings. For example, on the subject of mine drifts and tunnels, the present idea is that arching their backs increases their strength; this paper will indicate that this is not always true, and if it can be shown that under certain conditions arching becomes unnecessary an economic saving will result. In room-and-pillar work a question may arise as to whether arching the roof and gobbing the excavated material will result in timber saving, and a decrease in the dangers from falls of roof. It is to be distinctly understood that each mine must be treated as an individual problem, and that answers to these questions and many others can now be found after experimental laboratory data have been obtained. Mine-Arch Structure Fig. 1 shows the elements that affect the strength or behavior of the experimental arch. They are the span, crown thickness, radius of curvature, rise and restraint. The restraint in all cases was made sufficient to cause the arch to fail without displacing the restraining sides. Fig. 2a is a photograph of a model arch prepared for testing in the centri-

Jan 1, 1934

By G. R. Gohn, S. M. Arnold

The results of stress-corrosion tests upon several non-ferrous sheet metals are presented in this paper. The metals include tough pitch copper, five binary brasses, two leaded brasses, one copper-silicon alloy, two tin bronzes, and two nickel-silver alloys. The tests indicate that for most of these sheet metals, externally applied bending stresses below the yield point (0.01 per cent offset) do not result in stress-corrosion cracking as determined by the A.S.T.M. Tentative Method of Mercurous Nitrate Test for Copper and Copper Alloys (B 154-41T).~ Only in the cases of low brass, high brass and medium leaded brass, all cold-worked 4 B & S numbers hard, was any corrosion cracking observed below the yield strength, and in all cases such failures occurred at stresses above the proportional limit for these materials. However, when some of the same materials which showed no evidence of stress-corrosion cracking at stresses below the yield strength, are stressed beyond the yield point, stress- corrosion cracking is quite apt to occur. Since experience has shown that some of these materials, particularly the brasses, are susceptible to stress-corrosion cracking under service conditions, these tests would indicate that, besides externally applied stress and corrosion, plastic deformation in addition to that resulting from the original cold working of the material is also required to produce conditions conducive to stress- corrosion cracking.

Jan 1, 1945

By R. J. P. Lyon, A. E. Prelat, H. Lawrence

Introduction In 1977, the US Bureau of Mines awarded a grant to the state of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the state. Work had been done in Aiken County prior to the grant by USBM and state personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1:100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two US Geological Survey (USGS) 7 % - min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than zt 91.4 m. Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). [Fig. 1] shows a portion of one quadrangle overlay. [Table 1] gives a comparison of acreage measured for several mines from the 1-100 and IDIMS system vs. aerial photo measurements. The success of the preliminary work resulted in the South Carolina Land Resources Conservation Commission submitting a proposal to USBM for funding to expand the scope of work to other mineral mining operations within the state and determine if Landsat Imagery could be used to accurately locate and measure mining and reclamation activity on a continuing basis. Three separate tasks were proposed for selected kaolin mines in Aiken County: Task 1, to measure changes in active mine developments over the period 1974-77; Task 2, to measure reclamation activity, and, if time permitted, seasonal changes in mine signatures over the same period of time; and Task 3, to classify one complete mining operation (i.e., differentiate between active, spoil, overburden, water, reclaimed portions and surrounding terrain. The major effort was centered around J.M. Hubeis Richardson mine. Mining operations were progressing in a northerly direction and included three areas of reclamation: one prior to 1974; one started during early 1974; and one reclaimed during 1976. A discussion of all work done under the grant is available in the March 1979 Final Report listed under References. Computer compatible tapes (CCTs) containing MSS data from Landsat Path 18, Row 37, were purchased from the National Aeronautics and Space Administration (NASA) covering the period February 1974 through January 1977. The MSS data were processed on the General Electric Image 100 using parallelepiped classification at the EROS Data Center's Data Analysis Laboratory, Sioux Falls, SD, and at the Stanford Remote Sensing Laboratory, Stanford University, Palo Alto, CA, utilizing both an unsupervised classification (ISOMIX) and a supervised classification (sequential discriminant analysis). Studies at Stanford University Remote Sensing Lab (SRSL). In Feburary 1977, initial work was begun at Stanford using the STANSORT computer program running on a DEC PDP-10 (Honey, Prelat, and Lyon, 1974). This software is fully interactive and designed to study Landsat CCT data at high resolution (small areas) on a pixel-by-pixel basis (Lyon, 1977). Unsupervised Classification. The initial step was to locate the Richardson mine on the positive print of the full Landsat scene from CCT 1644-15252, dated 6/17/74. This was relatively easy due to a large abandoned kaolin mine and a long narrow pond clearly visible in the scene. Two unsupervised classifications of the Richardson mine were run using ISOMIX clustering (Honey, Prelat and Lyon, 1974). (ISOMIX essentially follows the interactive clustering procedures of ISOCLS Kan, Holley, and Parker. 1973). Although the classifications were successfully accomplished, it was apparent from the TV display that the results did not clearly define the mine areas. A supervised classification would have to be made in order to clearly separate each portion of the mine. Supervised Classification. This classification was done using the Stepwise Discriminant Program (BMDO7M) which is part of the BIOMED package (Dixon, 1970) and involved the following steps: Training group populations were selected and the digital

Jan 1, 1982

In the examination of an undeveloped prospect a decision must be arrived at from an inspection of the outcrops and the exposures in a few shallow pits. Prospects that are offered for sale rarely expose any important quantity of good ore, work having usually been stopped when the immediate exploration no longer yielded favorable results. It should be borne in mind, furthermore, that a great majority of prospects have been examined many times, and if of conspicuous promise, would have been acquired-for development. In most cases the problem for the engineer, therefore, is to discover the traces of a valuable mineralization that has disappeared through solution, or the conditions that indicate the possibility, or probability, of underlying secondary enrichments. The available data being meager, every feature should be the subject of careful study-the condition of the outcrop, the structural relationships, the associations of minerals, the alterations of wall rocks, the chances for underlying enrichments, and so forth, as well as the actual assay value of the material exposed. It is frequently advisable to spend the time and money necessary to have trenches dug at various significant points along a promising outcrop; such exposures, even if the depth attained is slight, often disclose conditions that are not apparent at the actual surface, as for example, the existence of soft minerals and the distribution of the various minerals through the mass of the deposit. Trenches also permit samples to be taken from points that were not accessible during former examinations. Strong, persistent outcrops of uniform width may be taken to indicate the probable size and character of the underlying vein,

Jan 1, 1932

By E. R. Dean

A wire-feed mechanism has been employed to fabricute metal alloy film resistors to various sheet resistivities on oxidized silicon substrates. The effect of several thousand hours storage in air at elevated temperatures on the resistance and temperature coefficient of resistance is presented. Unprotected films of- sheet resistivity between 100 and 500 ohms per sq fabricated at 300°C substrate tenzperatures were unstable when stored at 150°Cfor extended periods. The higher sheet resistivity films exhibited the greatest instability; however, even the 100 ohms per sq films drijted excessively for device application. When stored at still higher temperatures, the normalized resistance increases to maximum, then decreases until a minimum value is obtained, then finally increases in resistance until open. The use of a protective overcoating of SiO has had considerable benejicial effects on the film stability, so that 250 ohms per sq films deposited on 300°C substrates are now stable after 1000 hr storage at 250°C and possess a temperature coefficient of resistance less than 200 ppm per C. The use of a low substrate temperature during depositon (100°C) enables the preparation oj resistors with very low tenperature coefficients of resistance (10 to 20 ppnl per 'C). However, these films are less stable than their higher substrate temperatuve counterparts. During extended storage, the resistance of the protected films always decreases with lower substrate films exhibiting larger normalized resistance decreases. This resistance decrease is accompanied by a linearly related increase in the temperature coefficient of resistance. The electrical behavior of these films may be explained by postulating That the structure of the films is in the transition region between thick continuous films and ultrathin island structure films so that the conductivity is the restlt of both electron scattering and tunneling-activated charge carrier creation between neighboring grains. The annealing behavior when thermally aged is the result of defect anneal, grain growth, and selective oxidation. TheRE is a considerable interest in thin metallic films for use as resistor elements in microelectronic circuits.1,2 These resistor films must be stable when exposed to elevated-temperature storage or operating ambient, possess low temperature coefficients of resistance (hereafter referred to as T.C.R.), and be of a high enough sheet resistivity to be useful. The resistivity and T.C.R. of a thin metallic film are determined by the structure and thickness of the film. Hence the stability of the film when exposed to stress would depend on the stability of the structure. The resistivity of a thin film is the result of the electrons' interaction with the lattice vibrations (electron-phonon scattering), scattering of electrons due to impurities, defects, and grain boundaries and specula reflection from the film surfaces.3' All of these effects serve to reduce the electron mean free path and result in a resistivity higher than the ideal bulk. In ultrathin films possessing essentially an island structure consisting of a planar array of aggregates separated by a few to a few tens of angstroms, conduction is dominated by a combination of tunneling and activated charge carrier reation. Thin films would be characterized by relatively low resistivity, positive T.C.R., and reasonable structure stability whereas ultrathin films possess unstable structures, negative T.C.R., and exhibit high resistivity. Feldman6 has investigated films intermediate between the two regions and postulates that the resistivity of a film in the transition region is composed of two linearly additive parts: that due to the resistance of the grains and that due to the gaps. The grain resistivity would represent the scattering of the conduction electrons by defects, surfaces, and phonon interaction while the gap term represents the tunneling contribution. For gold and platinum films, he found as the film structure becomes progressively less continuous, corresponding to thinner films, the absolute value of the T.C.R. becomes progressively smaller until negative values are observed with respective zero T.C.R.'s at about 35 and 150 ohm per sq, respectively. Recently the author7 investigated the behavior of a multicomponent alloy of nickel, chromium, and iron and found the T.C.R.'s of these films decrease with decreasing substrate temperature during deposition. The lower T.C.A. associated with lower substrate temperatures was attributed to an increased contribution to the total resistivity from the negatively temperature-dependent gap tunneling since it is well-known that thin films deposited on low-temperature substrates consist of a higher density of smaller grains than the same sheet resistivity films deposited on higher-temperature substrates. Under conditions of thermal anneal, the author found that, when various sheet resistivity films fabricated at 300°C substrate temperature are exposed to extended storage in air at 300°C, the thinner films increase in resistance until open, while the thicker films

Jan 1, 1967

By J. D. Forrester

Many have been prone to credit the decline of professional interest in some branches of mineral industry education to the industrialists and other agencies who use our graduates. We hear the cry that industrial salaries are too low, opportunities for advancement do not exist, and the mineral industry specifically and generally is not interested in the engineer's efforts. Perhaps the time now has come when we should "dress-ranks," examine our practices, and publicize and encourage advanced technical training instead of laying all our troubles elsewhere. There can be no doubt but that industry is interested and stands ready and willing to co-operate. This is demonstrated by the numerous grants-in-aid and co-operative industrial projects which have been made available to those relatively few schools which have been encouraging graduate study and research. There is no dearth of research problems in any of the mineral industry fields and the sooner we realize the great opportunities for constructive, technical research in all areas of our profession the sooner we will reap the benefits of our engineering enterprises by closer liaison and broader understanding with industry. An analysis is offered here of the status of graduate work and research in various phases of mineral industry education in the United States. It is

Jan 1, 1949

By R. A. Meussner, C. T. Fujii

Chromium solution in wustite depresses the oxygen activity in a nonideal manner and expands the lattice slightly. Gravimetric measurements of the equilibrium compositions of wustite containing 0.00 to 1.38 wt pct Cr define the oxygen potential (CO2-CO atm) and the limits of the phase field at 1000°C. These data extrapolate to a maximum solubility of 2 wt pct Cr. The lattice parameter data, room-temperature measurements of quenched samples, differ significantly from those in the literature. Both pure and chromium wus-tites contract at uniform and equal rates as the oxygen content (metal deficit) increases. The a. US metal deficit relationships are straight lines showing none of the curvature previously reported. At constant metal deficit, the a. expands by 0.002? on alloying with 0.4 to 0.5 wt pct Cr but is insensitive to further chromium additions: a small expansion rather than a marked contraction. These results require a modification of the accepted alloying mechanism. IN the high-temperature oxidation of Fe-Cr alloys in Ha-H,and CO2-CO atmospheres the vapor transfer of oxygen from the continuous wustite outer scale to the porous inner scale/alloy interface sustains the high oxidation rates.1"3 The driving force for this transport is the difference in the oxygen activity of the outer wustite and that at the inner scale/alloy interface. In pure CO2, as well as in CO2-CO atmospheres, carburization of the alloy accompanies this oxidation. Current efforts to evaluate the parameters controlling this carburization have shown that the process is not simple; i.e., the carbon concentration in the alloy initially increases rapidly, reaches a maximum, and then decreases slowly as the oxidation time is extended. This is the same pattern reported by McCoy for the more complex oxidation-carburization of stainless steels and an Fe-Cr alloy in CO2 at lower temperatures.4 These changes in the carburization process occur while the overall oxidation rate and the lattice parameters of the scale layers remain constant. If this invariance of the lattice parameter is assumed to indicate a constant scale composition and thus a constant oxygen potential, the carburization results are not easily explained. Electron microprobe traces across the thickness of these outer scales, however, have revealed distinct chromium gradients penetrating 10 to 50 µ from the inner surface where the chromium concentrations were estimated at a few tenths percent. The variation of the chromium cmcentration on the inner surface of the scale, and the resulting change of the oxygen activity, during the oxidation process is considered to be important in defining the carburization process. Thus, to gain an understanding of the complex oxidation-carburization proc- ess, it was necessary to measure the properties of wustite containing known amounts of chromium (chromium wustite). Although the general features of the Fe-Cr-0 equilibrium diagram between 900° and 1300°C have been fairly well established by Richards and white: Wood-house and White,6 Seybolt,7 and Katsura and Muan,8 there have been no detailed studies of the limits of the chromium wustite phase field or the properties of these alloyed wustites. The recent results of a limited study of chromium wustite by Levin and wagner9 indicate that more than 0.67 wt pct Cr is soluble in wustite above 850°C and that this alloying is accompanied by a substantial lattice contraction. This change in the lattice parameter was not evident in the X-ray diffraction patterns of wustite layers from the oxidation experiments;1,3 the lines were sharp even though a chromium gradient existed in the scale. The present paper describes gravimetric equilibrium experiments which delineate the boundaries of the chromium wustite single-phase field at 1000°C and define the changes in the oxygen activity and the lattice parameter of wustite as functions of chromium and oxygen contents. The lattice parameter data of chromium wustite obtained from these equilibrium and special quenching experiments differ considerably from those reported.9 Those for pure wustite show significant differences from the widely accepted data of Jette and Foote.10 Since the causes of these differences are not easily assignable, and since the literature contains many sets of data on wustite which if not in conflict are at best not in harmony, the experimental procedures are discussed in the present paper. EXPERIMENTAL Oxide Preparation. The specimens used in these studies were porous pellets compacted from high-purity (Fe,Cr)2O3 or Fe2O3 powders. These powders were prepared from electrolytic chromium (99.8 pct purity) and electrolytic iron purified by consumable-electrode, vacuum arc-melting processing (299.9 pct purity).11 The oxides were produced by standard analytical procedures: solution of the metals in acids (HC1, then HNO3 added), coprecipitation of the hydroxides (NHaOH), and filtering and washing these precipitates. Initial dehydration of the coprecipitated hydroxides was done in a porcelain evaporating dish heated by a Meker-type burner, final dehydration by firing in a recrystallized alumina crucible at 1000" to 1050°C for 20 hr in an electrically heated furnace. Spectrographic analysis detected the following impurities: silicon, 0.01 pct or less; aluminum, 0.001 pct to trace; manganese and copper, 0.0001 pct to none. Each of these levels is at least one order of magnitude lower than in commercially available CP grade ferric and chromic oxides. Fluorescence analy-

Jan 1, 1969

Discussion of the paper of R. H. RICHARDS and BOYD DUDLEY, JR., presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 191.5, pp. 67 to 72. R. H. RICHARDS, Boston, Mass.-I believe that the manner of working for efficiency in almost all lines is to study the conditions of highest efficiency, and then to measure what is being clone. We can then see how near we have approached the highest efficiency. Spigots in practice often use many times the water theoretically needed. There are places where that is necessary for safety reasons. There are, however, places where it is unnecessary, and in these places it seems to me that this work of Mr. Dudley's will be a great help to the mill man to arrive at the greatest economy of water and highest efficiency. ALBERT R. LEDOUX, New York, N. Y.-A good many years ago I received a telegram from that distinguished engineer, Hamilton Smith, which simply said in substance: "I have discovered that liquids will flow faster from a square orifice than from a round orifice of the same area, under the same head." I wondered why he sent me the telegram, but some time afterward he told me that he had been making experiments along that line in Montana; that he thought the discovery was interesting

Jan 5, 1915

By I. R. Kramer

The stress associated with the surface layer was deter-minedfor iron and molybdcnum. These measurements show that the surface layer plays a very important role in the plastic deformation of bcc metals. From the relationship between strain arui the surface layer stress and the back stress imposed by the internal obstacles, it is Proposed that the term of of the Hall-Petch equation is related only THE large number of studies on plastic flow of bcc metals have failed to delineate clearly the nature of the obstacles influencing dislocation movement. Since there have been numerous articles which have reviewed the mechanisms proposed to explain various aspects of plastic flow of bcc metals (for example, conrad1 and Keh and weissmann2), no attempt will be made here to discuss their conclusions. However, it should be to the surface stress while the term Kfd is the stress required to move dislocations through internal obstacles. Further, it was possible to derive the well-known empirical equation C = , and it is shown that the terprz a is comprised of two terms: a term Cs associated with the surface layer stress and Ci related to internal dislocation obstacles. pointed out that in all of these publications it has been tacitly assumed that plastic flow occurred uniformly throughout the cross section of the specimen (except, of course, for the Luders band region), It has generally been further assumed that the nature and distribution of the obstacles opposing the motion of dislocations are of the same type throughout. The role of the surface layer in bcc metals has not, as yet, been considered even though its role in fcc metals has been shown clearly to be of primary importance.3-5 Investigations on fcc metals have shown that at the onset of plastic deformation a surface layer acts to

Jan 1, 1968

By Theron Wasson

The Central Michigan area held first place in the state during the year. Midland and Isabella, the leading counties in 1932, produced most of the oil in 1933. The Porter field southeast of Mt. Pleasant and along the same structural trend saw the greatest drilling activity. In Porter during the year 117 new wells were drilled. Under proration these wells produced 3,583,617 bbl., or nearly one-half the total for the state, which has been estimated at 7,947,695 bbl. The Porter field is already outlined on all sides except the northwest. It probably reached its peak in 1933. Unless a new field of some magnitude is developed in 1934, Michigan will see a continuous decline. The Greendale extension to the old Mt. Pleasant field furnished the new flush for 1932. In 1933

Jan 1, 1934

By W. A. Backofen, D. L. Holt

Push-pull fatigue tests have been carried out at 4.2°K, 77oK, and room temperature on two poly crystalline materials of widely different stacking-fault energy (?): pure copper (? - 70 ergs per sq cm) and the Cu-8 wt pct A1 alloy (? - 2.8 ergs per sq cm). Constant stress-amplilude was imposed and measurement was made of the plastic-strain amplitude (ep) at saturation. Lives extended from 104 to 106 cycles. Designating lives at the various temperatures by NRT, N77, and N4.2. the ratios N77/NNT and N4.2/N77 ranged from 3.5 to 18 under the condition of common Ep . Metallo-graphic examination revealed different crack morphology in Cu-8 Al fatigued at room temperature, and at 77" and 4.2oK. At room temperature, cracks lay in or near grain and lain boundavies; at 77o and 4.2oK. cvacks were transcrystalline. Tests on single crystals of Cu-8 A1 showed that such a change in the cracking mode in polycrystallitle material accounted for a factor of- about 3.25 in N77/NRT . The longer life at lower tewperatztre (conslant cp) has heels attributed to two deuelopinents: a reduced production of the dislocation tangles and subgrain boundaries which serve as paths of rapid cracking, and suppression of oxygen chetni-sorption at the crack tip It was concluded that in both materials the luller accounted for an extension of the life at 4.2oK beyond that at room temperature by a factor of 15. XV ECENT experiments on the fatigue of Cu-A1 alloys in the so-called high-cycle range (greater than lo4 cycles) have emphasized the importance of stacking-fault energy (y) as a quantity affecting crack propagation rate and fatigue life.1,2 It was found in comparisons at essentially fixed plastic-strain amplitude that crack growth rate decreased by a factor of about 5 over the composition range from copper (? - 70 ergs per sq cm) to Cu-8 wt pct Al (? - 2.8 ergs per sq cm). The argument was made that, when stacking-fault energy is high, cross slip and climb are favored, so that dislocation tangles and/or subgrain boundaries form more readily under cyclic loading. Since the boundaries and tangles act as paths of rapid crack propagation ,3, 4 life is shortened as a result. However, when stacking-fault energy is reduced (as by alloying), cross slip and climb become more difficult, with the result that substructure formation is retarded and growth rate is also reduced. A purpose of the present work was to investigate the substructure effect in relation to temperature. As temperature is lowered, ? is varied only slightly (if at all), but decreased thermal activation can interfere with cross slip and climb. Thus substructure formation could be curtailed and life increased. Fatigue life in the high-cycle range is also known to be strongly influenced by environment. Working with copper, Wadsworth and Hutchings observed that life in a vacuum of 10-8 mm Hg exceeded life in air by a factor of 20.5 They isolated oxygen as the agent that furthered cracking. While the details are still unclear, a requirement in any mechanism of oxygen-accelerated cracking is that there be chemisorption at the crack tip. That could prevent welding on the compression half cycle,= interfere with reversal of slip,1, 6 or aid in breaking metal-metal bonds at the crack tip.5'7 In the work being reported here, temperature was lowered by immersion in liquid nitrogen and helium, which also served to reduce both the oxygen concentration and chemisorption rate. A possible effect upon life, i.e., a lengthening, had to be recognized. Several researchers have determined fatigue lives at low temperatures presenting their results in the form of stress amplitude (S) vs cycles in life (N) curves.8-11 Such curves reflect, primarily, the fact that metal is strengthened by lowering temperature; effects of substructure and changing environment tend to be masked. The difficulty can be overcome by comparisons based on identical plastic-strain amplitudes, and in the present work the dependence of life on both plastic strain and stress amplitude was established. EXPERIMENTAL Materials. The principal materials were polycrystal-line copper (? - 70 ergs per sq cm)" and the Cu-8 wt pct Al alloy (? - 2.8 ergs per sq cm),I3 the latter being near the limit of solubility of aluminum in copper and having, therefore, the lowest stacking-fault energy in the CU-Al system. Specimens were machined from 0.118-in.-diam cold-swaged rods of high-purity (99.999 pct) copper and the Cu-8 Al alloy, the latter produced initially in a graphite boat by induction vacuum melting a mixture of 99.999 pct Cu and 99.99 pct Al. The machined specimens were annealed to produce mean grain diameters of about 0.070 mm in copper and 0.190 mm in the alloy. Specimen dimensions are given in Fig. 1. Values of the tensile yield stress, ultimate strength, uniform strain (determined by the Considgre construction), and reduction of area, for both materials at 4.2oK, 77oK, and room temperature, are listed in Table I. The tensile apparatus in which these results were obtained has already been described.14 Apparatus. Specimens were fatigued in push-pull with a machine that is illustrated schematically in Fig. 2. The specimen is first soldered into the top grip (1) with Woods metal, and the grip is then screwed into the inner tube (2) which is connected to the drive rod of the Goodmans vibration genera-

Jan 1, 1968

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now hen changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical

Jan 1, 1932

By AIME AIME

FRANCIS ANDREW THOMSON was born in London, Dec. 21, 1879, coming to the United States by way of British Columbia where he lived until he matriculated at the Colorado School of Mines. When only sixteen he was inducted into the mining industry as apprentice assayer and millman at the Victoria Metallurgical Works. Following his training at Golden he had more practical mining and milling experience at several properties in the West, and studied a little as well at the Royal School of Mines, in London, and at the Ecole des Mines, in Paris.

Jan 1, 1939

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By L. A. Roe

The flotation of fine particles less than five microns in diameter and the flotation of liquids from liquids generally requires bubble generation methods different than methods used in dispersed air type machines used in mineral flotation. Conditions in the separatory zone in mineral cells are generally more dynamic as compared to the quiescent conditions often absolutely necessary for the flotation of fine particles and liquids. An example of quiescent flotation with very fine bubbles is the lithium flotation plant which operated at Trona, California for 34 years, until it ceased operations in 1978. A review of the process development and the commercial flotation operations at Trona is given in this paper. The clarification of oil field brines by flotation of the oil from the brine has been used for over twenty-five years. Recent installations related to the Prudhoe Bay oil field and the Alaska pipeline are described.

Jan 1, 1980