Search Documents

By John E. Conley

THE slate industry of the United States has shown a marked decline in value of products made annually since the peak year 1925, although there has been moderate improvement over the lean years 1932 to 1934. In 1940, the value of all slate products sold was approximately 5 3/4 million dollars for a total output of 473,450 short tons. The quantity sold was a little less and the value a great deal lower than the annual averages for the past two decades. Enormous quantities of waste materials result from the quarrying, splitting and milling of slate. Obviously, utilization of such waste material is desirable, not only from the viewpoint of economical operation but also for the purpose of conserving natural resources. One possible use is to produce expanded or puffed lightweight aggregate for use in concretes. Such concretes are strong enough for specific uses, and the advantage of lightness could be obtained in such structures as the walls and roofs of buildings, suspension-bridge roadways and various other applications where weight is a factor. Conceivably, these uses could consume an appreciable annual tonnage. USE OF WASTE SLATES FOR MAKING AGGREGATES The lightweight-aggregate industry has been discussed elsewhere4.5 and need not be covered in detail in this paper. The materials commonly utilized are naturally occurring aggregates such as volcanic cinder, tuff and pumice; by-product materials, such as ordinary cinders and air-cooled slags; and the specially manufactured products, including Haydite, Pottsco, Gravelite, Cel-seal, Superock and Waylite. Slates, however, have not been given the consideration they merit, especially in the United States. In the British Isles, some work has been done' on certain Welsh slates by the Building Research Station to stimulate the use of these wastes. REQUIREMENTS FOR RAW MATERIALS As pointed out by Hughes,4 the lightweight-aggregate industry is segregated in regions adjacent to large cities in order to localize the market and avoid the necessity of long freight haulage. Waste slate from the deposits of eastern Pennsylvania, northern Maryland, and Virginia would meet the basic requirement of any low-priced structural raw material. One apparent advantage is attained when slate waste, normally discarded, is utilized in the manufacture of a by-product. Mining or quarrying costs usually have been assessed against the main product. Some additional grinding might be desirable, but this operation would be relatively cheap, as most slates grind easily. It is believed that virtually all slates, when properly heated, will expand to some degree. However, types that will expand from 3 to 7 times their original volume are preferred. Fig. I illustrates the expansion of a Pennsylvania slate. The cube originally

Jan 1, 1942

By Sandip K. Mitra, John E. Dorn

The Basinki-modified Seeger equation for deformation of metals by means of thermally activated intersection of dislocations was used to ascertain the various factors responsible for the strain hardening of poly crystalline aluminum and a series of a solid solutions of magnesium in aluminum. The analyses were based principally on the rate of change of strain rate with stress and the Cottrell-Stokes ratio. From measurements of these quantities on a series of strain-hardened states, the force displacement diagram for intersection, the density of dislocations in the entanglements, and the contributions of the athermal local stress and long-range stress interactions were deduced. Poly crystalline aluminum was observed to have the same force-displacement diagram for intersection as single aluminum crystals, and the corresponding diagram for the magnesium alloys differed in a manner that suggested that small amounts of magnesium may decrease slightly the stacking fault energy of aluminum. Although poly crystalline aluminum had about the same initial density of dislocations as the single crystals, the density of dislocations increased much more rapidly with strain in the polycrystals. This factor and the higher back stresses generated in the poly crystalline aluminum were the major factors responsible for the higher strength of the poly crystalline aluminum, As the magnesium content of the alloys was increased, the initial density of the dislocations also increased. Most of the alloy strengthening arose from this factor; alloying effects due to short-range order strengthening, Suzuki locking, Cottrell pinning, and so forth, were estimated to be quite small. The gveater rate of strain hardening in the alloys was deduced to be due primarily to the greater increase in the density of the dislocations with strain as the magnesium content was increased. It is the purpose of the present investigation to shed additional light on the average plastic behavior of a grain in a polycrystalline aggregate, by analyses, based on dislocation theory, of appropriate experimental test results. These deductions when compared with those from single-crystal data will then serve to illustrate the major items of difference between the plastic behavior of single crystals and the average behavior of a grain in a

Jan 1, 1963

By C. M. Brown

Selection criteria for the instrumentation employed in semi-autogenous grinding circuits are reviewed. Instruments in use for grinding mill and related process equipment start- up, shutdown, protection, monitoring, control, and performance reporting functions are discussed with examples given of current industry practice. The quantity and type of instrumentation used vary from operation to operation, but today many semi- autogenous circuits are highly instrumentated, and employ automatic process control for both circuit stabilization and optimization of economic performance. Examples of analog and digital based control systems exist, and are described.

Jan 1, 1982

By Klaus Schwerdtfeger

In order to test the performance of ZrO, (CaO) and Tho,(Yz03) electrolytes in the electrochemical determination of oxygen activities in liquid metals at steel-rrzakitng temperatures , electromotive force measurements have been made with the following cells: The oxygen-- activities are calculated from the electmrnotive forces for the investigated systems. The standard free energy of- formation of MnO and the activity of manganese in Fe-Mn melts are derived. Indications are that the Zr 0z(Ca0) electrolyte exhibits little electronic conductivity at oxygen pressures as low as 10'a atnz at 1600°C; however, the partial electronic conductivity may become noticeable at lower oxygen activities. The Tho,(Yz03) electrolyte is found to be an ionic conductor at the oxygen pressure as low as that for the Mn + MnO equilibrium, but exhibits partial electronic conductivity at oxygen pressures higher than 10"1 atm (1500°C). fi. better control of oxidation and deoxidation reactions in steelmaking may be facilitated if the oxygen activity in the steel is known during various stages of the process. In the present work oxygen activities have been measured in liquid iron, manganese, and iron alloys with galvanic cells using ZrOz(CaO) and s solid electrolytes with the object of establishing the range of oxygen pressure in which these materials can be used as electrolytes at steelmaking temperatures. Calcia-stabilized zirconia and Tho2-Y203 solid solutions are oxygen ion conductors. Such electrolytes were first used by Kiukkola and Wagner1 and Peters and ~ann' in galvanic cells for the determination of thermodynamicquantities of oxide systems in the temperature range 700" to 1200°C. At these moderate temperatures calcia-stabilized zirconia has been found to exhibit predominantly ionic conductivity at oxygen pressures as low as those for the Cr + Crz03 equilibrium,394 but at lower oxygen pressures elec- tronic contribution to conductivity becomes significants4 The Th02-Y203 solid solutions are ionic conductors at oxygen pressures lower than those applicable to zirconia base electrolytes.5'6 At high oxygen pressures Thoz base electrolytes exhibit significant p-type semiconduction. At the time the present experiments were carried out several papers1'-* were published on the electrochemical determination of oxygen activities in liquid iron using the ZrOz(CaO) electrolyte. The results of different authors do not agree well. For instance, according to Fischer and ~ckermann" stabilized zirconia can be used to measure oxygen contents in liquid iron larger than 0.02 wt pct, but according to Baker and west1' ZrOz(CaO) cannot be used for the determination of oxygen content in liquid iron because of high electronic contribution to the conductivity. Fig. 1 is a schematic diagram of the apparatus used. About 500 g of liquid metal is contained in a crucible into which a stabilized zirconia or Th02(Y203) tube is immersed. A platinum contact wire is pressed (with a spring mechanism) against the inside bottom wall of the electrolyte tube. The tube is flushed continuously with a stream of air, CO-CO, (or Hz-C02) (at 0.96 atm and at a rate of about 300 cu cm per min), via an alumina tube inserted inside the electrolyte tube. This alumina tube also contains the Pt-Pt/10 pct Rh thermocouple. A capillary alumina tube shielding the other contact wire is immersed in the melt. The molybdenum contact wires were used mostly; in some cases platinum wire was employed. Molybdenum has the advantage that it dissolves more slowly in the melt than platinum. The whole cell was contained in the alumina reaction tube of a resistance furnace with molybdenum winding. The reaction tube was closed gas tight at both ends and flushed continuously with argon. Because of the poor thermal shock resistance of the electrolyte tubes the cell had to be assembled in the cold furnace. The electrolyte tube and alumina sheath

Jan 1, 1968

By J. Ruzicka

IN creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently bear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addi-tion to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabri-cated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment.

Jan 1, 1937

By C. M. Sellars, F. Maak

Electvomotie -force measurements hazle been made on ten Au-Ni alloys at temperatures 7754 825O, 900O, and 935°C using galvanic cells with solid electrolyte. Partial and ivtegral thermodynamic functions are derived from the determined activities. which show la9,ge positive deviations jvom Raoult's law. The enthalpies of mixing- are in close accord with calorinletric data and are of comparable accuracy. The results are used to determine the miscibility gap and the spinoidal curL1e, and are qlalitaticely interpreted in terms of the large size difference and electvonic interactions between gold and nickel. Tabulated nalues of the actielities and partial and inteqal free energies, entropies , and enthalpies of mixing are given in the appendix. The Au-Ni binary alloys are of particular interest thermodynamically as despite the large size difference between gold and nickel atoms they have a simple phase diagram.' This shows complete solid solubility above a miscibility gap with a maximum at about 71 at. pct Ni and 810°C. Activity measurements (over a range of temperature) have been made previously on this system using an electrolytic-cell method with a liquid chloride eletrolyte. The accuracy of this data has, however, been queried3'4 as it leads to values for the enthalpy of mixing which are too high when compared with calorimetric measurements.46 Also, the entropy of mixing is too high when compared with the values derived from specific-heat measrements. It was therefore considered worthwhile redetermining the activity data using a galvanic cell with a solid electrolyte (0.85 ZrO, 0.15 CaO). This method is based on a technique introduced by Kiukkola and aner'' and has been used to determine the thermodynamic data for Cu-Ni alloys.' THE ELECTROLYTIC CELL The cell used to determine the activity of nickel in Au-Ni alloys was: The cell reaction, which is discussed for a similar cell by Rapp and Maak, gives a direct measurement of the activity of nickel in the alloys as where aNi(alloy) is the activity of nickel in the alloy, 3 is Faraday's constant, E is the measured electromotive force, R is the gas constant, and T is absolute temperature. For the valid application of this type of cell the arrangement must be ther modynamic ally stable, which means that: 1) The free energies of formation of the oxides fulfill the relation 2) The vapor pressures or dissociation pressures of each component must be so small that during the time of the experiment the amount of any material transported by the gas is negligible. 3) Side reactions which change the alloy composition must be negligible. These reactions are possible both with the surrounding gas atmosphere and with neighboring solid material. The first two conditions are fulfilled by the above cell.' The third condition is approached by care in the experimental technique. The factors which control the attainment of equilibrium in this type of cell have been considered by Rapp and aak, who conclude that metallic diffusion in the alloy is the rate-control ling step. A lower temperature limit for the practical application of this cell is therefore set by the condition that equilibrium must be attained in reasonable times. EXPERIMENTAL MATERIALS AND TECHNIQUE The starting materials were mint gold (99.99 pct Au) and Mond nickel (99.9 pct Ni). Alloys, nominally 5 at. pct Ni and then each 10 at. pct across the system, were produced by vacuum-levitation melting compacts of mixed drillings of the pure metals. The nickel used for the reference tablets in the cells was melted in a similar manner. The alloy ingots, cast in boron nitride molds, were cold-forged and

Jan 1, 1967

By J. W. Lacey, F. H. Brinkman, J. E. Faris

This paper presents an analysis of the high-pressure, gas-driven LPG-slug process, based on fluid flow tests in areal models. Two types of tests were made. One series was made in low-pressure models which permitted observation of fluid movement. Three completely misci-ble analog fluids were used. A second series of tests was made in high-pressure models using methane, propane and a light refined oil saturated with methane at room temperature and 1,550 psig. Under the test conditions of room temperature and a pressure level of 1,550 psig, the phase diagram for the fluids used is similar to those for many of the field systems where the process is considered for use. A method for using these laboratory data to calculate field performance of the process is outlined. As a result of this work, it is concluded that small banks of LPG (5 per cent HV or less) are not effective in increasing oil recovery in horizontal reservoirs. Znstead, where small banks are used, the driving gas quickly penetrates the LPG bank because of fingering and channeling; and from this point on, the process behaves essentially as an immiscible gas-injection project. The validity of this conclusion was substantiated by: (1) laboratory studies of the effect of rate, model size and mobility ratio on miscible displacement in areal models; and (2) calculation of field recovery, which compared closely with actual field recovery. INTRODUCTION Field applications and pilot tests of the gas-driven, LPG-bank, oil-recovery process are on the increase. Most of these tests are employing small banks (2% to 5 per cent hydrocarbon volume) of LPG, which is miscible with both the driving gas and the oil in place, in an effort to attain an effective yet economical miscible displacement of oil by gas. The expectation of miscible displacement with small banks is based on the concepts that: (1) lengths of solvent-oil mixed zones, measured during miscible displacements in long slim cores, are representative of those that will occur in the field; and (2) areal sweep efficiencies5 measured in electrolytic model studies are applicable to miscible displacement in reservoirs. Our experimental evidence indicates that the mixed-zone lengths and sweep efficiencies mentioned are not applicable to miscible displacement in reservoirs. In this paper we present an evaluation of the gas-driven, LPG-bank oil-recovery process based on fluid flow experiments in areal models. These results are used to predict the performance of a field pilot test of this process, and the results are compared with the actual test results. THE EFFECTIVENESS OF LPG BANKS The effectiveness of LPG banks of various sizes in accomplishing miscible displacement of oil by gas was determined by displacement tests in a model representing one-quarter of a confined five-spot pattern. The model, 12 X 12 X 1/4 in. in size, was packed uniformly with glass beads. It was operated at a pressure of 1,550 psig and at room temperature; the fluids used were methane, propane and refined oil saturated with methane at 1,550 psig. The saturated oil had a viscosity of 1.2 cp at room temperature. The results of these tests are shown in Fig. 1, where recovery is plotted as a function of the volume of fluid injected for: (1) an immiscible-gas drive with an oil-to-gas viscosity ratio of 85; (2) three sizes of LPG banks; and (3) two completely miscible displacements with mobility ratios of 85:1 and 10:1. (The miscible displacement data plotted are the averages of several tests.) The results show that a 2½ per cent bank of LPG does not increase oil recovery over that obtained by immiscible-gas drive. The 7 and 17 per cent banks are, respectively, about 30 and 50 per cent effective (with reference to the M = 85 miscible-displacement curve) in increasing oil recovery at the point where 2½ hydrocarbon volumes (HV) of fluid have been injected. The percentage effectiveness of the banks at a given volume of fluid injected is defined as Recovery by Bank — Recovery by Gas Drive Recovery by Miscible Recovery by Flooding Gas Drive We conclude from these results that banks of LPG smaller than about 5 per cent HV in an individual stratum will cause from little to no increase in oil recovery. This finding was substantiated by work in low-pressure models, which permitted visual observation of fluid movements. In these tests, three completely miscible fluids having the same viscosity ratios as those used in

By H. A. Bright, H. C. Vacher, J. G. Thompson

The methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value representing the sum of the oxygen contents of several or all of the oxide constituents present. With such diversity in the principles and aims of the different groups, it is not surprising that concordance of results by different methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the various methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1937

By J. C. Van de Water

In June the supply of M3 army demolition powder being used for mudcapping was depleted and we switched to 4 by 8, 60% Special Quarry Gelatin dynamite. This size cartridge has proved convenient, as a half stick will handle the average boulder. By keeping the gelatin in the paper while cutting it in two, there is little contact with the gelatin and therefore fewer headaches among the powdermen. To further help prevent the headache nuisance the men are furnished with plastic coated gloves. Boulder breaking costs as reported last year were $0.426 using M3. This year, 8180 boulders have been broken with M3 at a cost of $0.472 each and 7479 with 60% Quarry Gelatin at a cost of $0.660 each. This rise in cost is due entirely to the greater cost of the Gelatin as the method has not changed.

Jan 4, 1950

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By W. C. Ellis, M. E. Fine

WHEN certain binary Fe-Ni alloys are worked cold and then stabilized by a stress-relief anneal, their Young's moduli are nearly invariant over a substantial temperature range determined by composition and work-anneal history.' In the present investigation addition of molybdenum to such alloys (besides increasing the yield strength) was found to diminish the sensitivity of the thermal coefficient of Young's modulus to composition changes. Such alloys are of interest for applications requiring 1 a metal with controlled, low temperature coefficient of Young's modulus and substantial magnetic permeability.' Young's modulus ordinarily decreases with rising temperature. In ferromagnetic alloys a change in modulus on heating due to loss of ferromagnetism modifies the .temperature dependence. Far below the Curie temperature ferromagnetism alters the modulus in two ways: a—Addition of the energy of magnetization, a function of interatomic distance, changes the relation between interatomic energy and distance.' This lowers the modulus in the Fe-Ni and Fe-Ni-Mo alloys of this investigation. b—An applied stress changes the ferromagnetic domain arrangement so that linear magnetostriction contributes to the strain and further lowers the modulUs.~ Since in the alloys of this investigation both effects lower the modulus, loss of ferromagnetism on heating changes the slope of the modulus-temperature curve in a positive direction. With increasing temperature the slope of the modulus-temperature curve, due to progressive loss of ferromagnetism, becomes less negative, goes through zero (the modulus is minimum), becomes positive, and resumes its normal negative value above the Curie temperature.' The increase in modulus and decrease in curvature in the modulus-temperature curve occurring on work hardening have been attributed to a reduction in effect (b).'. Vn the absence of ferromagnetism work hardening through introduction of residual strains would be expected to decrease the modulus.' Alloy Preparation—Test Methods Four series of alloys having nominal molybdenum contents of 5, 7, 9, and 10 pct and containing 47 to 58 pct Fe (the analyzed compositions are given in Table I) were melted in air and cast as bars weighing from 2 to 6 lb. The charge consisted of electrolytic nickel, Armco iron, molybdenum (99+ pct) or ferromolybdenum (62 pct Mo), manganese, and aluminum as a deoxidizer. The bars were swaged cold to the desired diameters with intermediate anneals. Alloys in this composition range are reported" to be face-centered cubic and ferromagnetic at room temperature. The Curie temperatures" decrease with molybdenum. For example, keeping the Ni/Fe ratio at unity and increasing the molybdenum from 0 to 17 pct decreases the Curie tempera- ture from approximately 500°C to room temperature. (The 17 pct Mo alloy requires quenching to retain a single phase.~) Young's modulus at a series of temperatures from —50" to 100°C was determined by a dynamic method previously described.', " In this method Young's modulus is calculated from the resonant frequency (in this case approximately 50,000 cycles per second) of a rod sample (approximately 2 in. long) vibrating longitudinally in the first mode. The densities of the samples at room temperature, Table I, were determined by the standard method of weighing in air and reweighing in redistilled bromobenzene. The linear coefficients of expansion, Table I, needed to calculate the sample length and density at the temperature of measurement, were obtained by observing the change in length (22" to 100°C) of an 8 in. gage distance with a two microscope cathetometer. The values of density and coefficient of expansion in the few samples checked are independent of treatment to the accuracy reported. This was assumed to be general for all the samples. The modulus values are accurate to &0.05x101' dynes per sq cm. However, values of thermal change in modulus are accurate to 20.005~ 10" dynes per sq cm. Young's Modulus Values at 25°C: The modulus values of O', 5, and 10 pct Mo alloys at 25 °C are plotted in Fig. 1 as functions of nickel. After working cold, the samples were either recrystallized at 950" to 1000°C or given a low temperature stabilizing anneal at 400° C. The 400°C anneal does not reduce the hardness nor cause recrystallization. Annealing at 400 °C does

Jan 1, 1952

By E. C. Bohlen, H. l. Burghoff

THE work reported in this paper was carried out to supplement the existing information concerning directional properties and recrystallization textures of annealed brass sheet and strip. These characteristics are of direct interest when the forming and drawing properties of such material are being considered. Among those who have made contributions in this field are Bass and Glocker;1 Bauer, Göler and Sachs;2 Phillips and Samans;3 Pratt;4 Price;5 Cook;6 Richards;7 Brick;8 and Brick and Williamson.9 These investigators have found, in general, that in brass strip that shows directional variations in properties, tensile strength has a minimum value and elongation has a maximum value at 45° to the rolling direction. The most pronounced directional properties have been found in material given the greatest reductions in rolling followed by high annealing temperatures. Recrystallization texture of brass has been variously reported as (113)[112], (001)[100], and a combination of (110)[115] and traces of the primary rolling texture, (110)[112]. The directional studies have been very informative, but actual tests appear to have been confined to material in its final condition. Tests at intermediate stages have received little attention although previous history of some materials has been partly considered. Perhaps the most comprehensive investigation was made by Cook,6 who studied the directional properties of 70-30 brass strip for which the final and penultimate, or next to the last, anneals and the final reductions were varied. He found that, for any given combination of penultimate anneal and final reduction, the tendency toward the development of directional properties was reduced as the temperature of the final anneal was decreased. In addition to drawing cups and making tensile tests of the finished material at various angles to the rolling direction, he measured the frequency and the angles of twins in grains for several specimens. Plots of his twin counts showed directionality for the materials that produced eared cups. TEST MATERIALS AND EQUIPMENT For this investigation, one commercial heat of 68-32 brass was cast in the form of bars for cold-rolling, 13 ½ in. wide and 1 ½ in. thick. The analysis was as follows: 68.83 per cent copper, 0.04 per cent lead, 0.01 per cent iron, 31.12 per cent zinc (by difference). The bars were so processed to the final thickness, 0.020 in., as to obtain on this thickness all possible combinations of the variables listed below except those involving the sequence of 84 per cent penultimate reduction and 84 per cent final reduction: I. Penultimate reductions of 37 per cent, 50 per cent and 84 per cent; 2. Penultimate anneals at 800°, 900°, 1050° and 1200°F.; 3. Final reductions of 37 per cent, 50 per cent, 69 per cent and 84 per cent;

Jan 1, 1942

By Norris Johnston, Carrol M. Beeson

For many years the permeability of reservoir sands has been measured by flowing air through a cleaned and dried core sample. This differs from the true reservoir permeability in one important respect: the rock particles in the reservoir are surrounded by interstitial water, not air, and their physical shape and condition of hydration are greatly dependent thereon. Permeability as defined must be measured with a single-phase fluid. Since no means exist for removing the oil and gas from a core sample by simply flowing water through it, the sample must be cleaned and then resatu-rated with water before testing. The present discussion attempts to show that after the cleaning process a considerably different permeability is determined with salt or fresh water than is obtained with air. The postulate is made that the salt-water permeability is probably closer to the true reservoir permeability than is the measurement with air. This is discussed in relation to both physically possible and economically feasible measuremerits. Data On more than 1200 core samples are given to show the nature of the effects observed, and a plea is made for others to consider water permeability measurements as a routine necessity, eventually replacing air permeability in regions where the differences are great. Introduction Permeability is defined1 as a "a measure of the capacity of a porous medium to transmit fluids, when there is no interaction between the solids and the fluid." Darcy's law of liquid flow in porous media states: kA?P QµL/A?L [I] where Q represents milliliters of liquid of viscosity p centipoises passed per second through a porous medium of permeability k darcys and cross-sectional area A sq. cm. under a pressure gradient ?P/L atmospheres per centimeter, the flow being understood to be laminar or viscous, not turbulent. This equation defines the darcy. For the case of radial flow in a uniform sand, such as usually exists in the neighborhood of a well in an oil or gas sand, Darcy's law becomes:2 Here h is the net sand thickness in feet, Pe and Pw are pressures at the drainage radius4 and well radius, and re and rw are these radii, respectively. The productivity index3 is defined as the barrels of liquid produced per day per pound per square inch mean pressure differential between ferences and well bore, and is thus: By further definition, the specific productivity index is: or in terms of practical units, and allowing for shrinkage:

Jan 1, 1945

By K. E. Brown, A. R. Hagedorn

A 1,500-ft experimental well was used to study the pressure gradients occurring during continuous, vertical, two-phase flow through 1-in., 1 1/4-in. and 1 1/3-in. nominal size tubing. The test well was equipped with two gas-lijt valves and four Mathak electronic pressure transmitters as well as with instruments to measure the liquid production rate, air injection rate, temperatures and surface pressures. Tests were conducted for widely varying liquid flow, rates, gas-liquid ratios and liquid viscosities. From these data, an accucrate pressure-depth traverse was construcred for each test in each of the three tubing sizes. From the results of these tests, correlations have beer] developed which allow the accurate prediction of flowing pressure gradients for a wide variety of tubing sizes, flow conditions, and liquid properties. Also. the correlations and equations which are developed satisfy the necessary condition that they reduce to the relationships approprate to single-phase flow when the flow rate of either the gas or the liqutid phase becomes zero. All the correlations involve only dimensionless groups. which is a condition usually Sought for in similarity analysis but not always achieved. The correlations developed in this study have been used to calculate pressure gradients for pipes of larger diameter than those upon which the correlations are based. Comparisons of these calcuclaed gradients with experimetally determined gradients for the same flow conditions obtained from the literature indicate that extrapolation to these larger pipe sizes is possible with a degree of accuracy sufficient for engineering calculations. The extent of this extrapolation can only he determined with additional data from larger pipe diameters. INTRODUCTION The accurate prediction of the pressure drop expected to occur during the multiphase flow of fluids in the flow string of a well is a wideiy recognized problem in the petroleum industry. The problem has been brought even more into prominence with the advent of tubingless or slim-hole completions which use small-diameter tubing. Many of the correlations which give reasonably accurale results in the lager tubing sizes are greatly in error when applied to small-diameter conduits. Small-diameter conduits are defined as 1 1/2-in. nominal size tubing or smaller. The study of the pressure gradients which occur during multiphase flow of fluids in pipes is exceedingly complex because of the large number of variables involved. Further difficulties relate to the possibility of numerous flow regimes of widely varying geometry and mechanism and the instabilities of the fluid interfaces involved. Consequently, a solution to the problem by the approach normally used in classical fluid dynamics based on the formulation and solution of the Navier-Stokes equation has not been forthcoming. This is primarily the result of the nonlincarities involved and the difficulty of adequately describing the boundary conditions. As a result of the foregoing, most investigators have chosen semi-empirical or purely empirical approaches in an efford to obtain a practical solution to the problem. Much of the previous work in this area was done in short-tube models in the laboratory. A number of problems arise, however, when attempts are made to extrapolate these laboratory results to oilfield conditions where a much longer tube is encountered. In those few studies where data taken in long tubes were utilized, the data covered only a limited range of the variables, and as a result inaccuracies are introduced when the correlations are extended outside the range of the original data. Also, as a consequence of the limited amount of data available for these studies, the effects of several important variables were overlooked. The problem of predicting the pressure drop which occurs in multiphase flow differs from that of single-phase flow in that another source of pressure loss is introduced, namely, those pressure losses arising from slippage between the phases. This slippage is a result of the difference between the integrated average linear velocities of the two phases, which in turn is due to the physical properties of the fluids involved. In contrast to single-phase flow. the pressure losses in multiphase flow do not always increase with a decrease in the size of the conduit or an increase in production rate. This is attributed to the presence of the gas phase which tends to slip by the liquid phase without actually contributing to its lift. Many investigators have attempted to correlate both the slippage losses and the friction losses by means of a single energy-loss factor analogous to the one used in the single-phase flow problem. In an approach of this type, hourever, many of the important variables, such as

Jan 1, 1966

By F. O. Shuck, F. E. Butler

A diaphragm diffusion cell suitable for use with liquid metals was designed and tested by measuring the diffusion coefficients for a Hg-10 pct In alloy at 25°C. The binary diffusion coefficient and the coefficients for In and Hg tracers were measured at this composition. The measured coefficients for both tracers were less than the binary diffusion coefficient. When these coefficients were combined with the activity correction term of Darken, the predicted binary coefficient was somewhat higher than the experimental value. In recent years a number of investigators have been studying diffusion of liquid metals in order to gain a better understanding of the liquid state and to examine possible applications to liquid metal processing. The bulk of this work has involved either self-diffusion or diffusion of low concentrations of solute metals in an essentially pure solvent metal. The most common experimental technique employed has been the capillary-reservoir method of Anderson and saddington1 since it is well-suited to measurements involving low concentrations of solutes. As an expansion of previous studies, an investigation of the variation of diffusion coefficient over large composition ranges has been undertaken in this laboratory. Although it is possible to modify the capillary-reservoir method for such measurements, the technique loses its principal advantage of requiring only small quantities of solutes. Therefore, it was felt desirable to investigate other possible experimental techniques applicable to measurements over large composition ranges. A technique which has been used widely in measurements of other liquid systems and seemed potentially applicable to studies of liquid metals was the diaphragm cell. This method has been found to combine relative simplicity of operation with accurate and reproducible results. In use with normal liquids, the tyiical diaphragm cell utilizes a porous glass disk. However, because of the high surface tension, it is not possible to use a diaphragm of such fine pore structure with liquid metals. Furthermore. projected use at high temperatures makes the use of glass undesirable. Consequently, the first problem was the search for an appropriate cell design. EXPERLMENTAL Diaphragm Cell. A number of possible cell designs were examined. Prototypes of several were constructed and tested. The final design is shown in an exploded view in Fig. 1. The cell consists of two identical chambers, one on either side of a 0.20-in.-thick partition. The chambers are 0.15 in. deep and have a volume of 3.45 cu cm. Each chamber is provided with two small threaded holes for filling and emptying. The filling holes may be sealed with stainless-steel screws. Drilled lengthwise through the center partition is a 0.250-in.-diam hole. Inserted into this hole is a rod having seven 0.059-in.-diam holes drilled radially through it. The total "hole" volume is 0.078 cu cm. When the rod is properly aligned, the holes in it constitute the "diaphragm" through which diffusion occurs. The center section was of Teflon and the rod and face plates were of Plexiglas. Four such cells were constructed and used in this study. Subsequent to this investigation, a similar cell constructed entirely of iron was fabricated and tested at higher temperatures. Several considerations led to this final design. It is desirable to minimize the volume of the cell chambers to decrease the time required for a measurement. However, the total volume of metal in the diaphragm must be small in comparison with that in the chambers. To facilitate filling and emptying it is desirable to have a diaphragm which may be closed.

Jan 1, 1970

Alexander N. Winchell, Butte, Mont. (communication to the Secretary): Mr. Spurr calls attention to the fact that an ore-deposit may be due to a succession of concentrations at different geological epochs. He cites an example of such a condition on Napoleon creek, a branch of Forty-Mile creek, Alaska. It will perhaps be of interest to call attention to another example of the same general character, not so remotely situated. The example referred to is located on Pole creek, a tributary of Cherry creek, in the extreme northeastern part of Madison county, Montana. An excellent geological map of this region is to be found in the Three Forks folio (No. 24) of the United States Geological Survey. According to this map, Pole creek, in its upper course, occupies the contact between the " Flathead " formation, which Peale correlates with the Middle and Lower Cambrian, and an area of gneisses and schists supposed

Jan 1, 1903

By H. C. Howard

Reaction of oxygen and bituminous coal starts as soon as the coal bed is exposed to air and, with some coals, proceeds with significant velocity even at normal temperatures and at normal oxygen partial pressures of one-fifth of an atmosphere. At higher temperatures, the reaction is greatly accelerated and ultimately a condition is reached where the process is very rapid and we then speak of combustion. It is the purpose of the present paper to discuss the reactions of oxygen and coal at temperatures below those of active combustion. It is these low temperature oxidation reactions which are responsible for heating in storage and for marked changes in agglutinating proper-ties. These reactions may also be employed for the preparation of organic acids, which are of direct interest to the chemical industry. For convenience in discussion, the low temperature reactions of oxygen and bituminous coal can be roughly divided into three stages though there is, of course, overlapping. Stage I is a surface oxidation stage, characterized by the addition of oxygen, with the formation of oxygen containing groups some of which have acidic properties. Carbon dioxide, carbon monoxide and water may be formed con-comitantly and are always liberated at higher temperatures, and in cases where the oxidation is prolonged. Superficially, the coal is little affected by this primary stage of oxidation and usually only minor changes in ultimate composition result. There may be definite changes in coking and coking properties, and heat of combustion susceptibility to further oxidation. The presence of acidic groups can be demonstrated by specific reactions. These groups may show cation exchange properties like the mineral zeolites. The formation of oxalic acid has been reported. If the oxidation is continued, a large fraction of the organic material of the coal is converted ultimately into alkali soluble, acid insoluble products, which have been given the name "regenerated humic acids" and which are the characteristic products of Stage 2. These humic acids, in the solid stage, do not differ greatly in appearance from the original coal, but show large differences in chemical composition and chemical and physical properties. Along with the humic acids, carbon dioxide and some of the water soluble types of Stage 3, are also formed. If the oxidation is carried still further, the humic acids may be degraded completely to the simpler, lower molecular weight acids of Stage 3 which are characterized by solubility in acid as well as in alkaline media, and by their orange, yellow or white colors. Additional carbon dioxide is formed in the transformation from Stage 2 to Stage 3 and, for a number of American coals, a maximum yield of the water soluble types of acids is reached when about 50 pct of the carbon of the coal is converted to carbon dioxide. Primary Oxidation The initial step in the reaction of gaseous oxygen on coal, like that on carbon,

Jan 1, 1949

By J. L. Taylor, P. Duwez

The phase boundaries in the ternary system Ti-Cr-Al have been established at 1800° and 1400°F for alloys containing more than 60 pct Ti. The martensite transformation temperature has been measured for the titanium-rich alloys. THE studies of binary alloys of titanium with the transition elements which have been published so far1-0 ndicate clearly that the solubility of these elements is always much greater in the high temperature body-centered cubic form of titanium (ß phase) than in the low temperature hexagonal form. In this category of alloying elements are iron, nickel, chromium, manganese, vanadium, molybdenum, tungsten, columbium, and tantalum. Although studies of the nontransition elements have been rather limited, early work on titanium binary alloys'" has shown that most of them were not very soluble in the a form, with the exception of aluminum, for which the solubility in a is about 25 pct.13, 12 In addition to this large solubility in a, aluminum is also soluble in ß titanium to the extent of about 35 pct and the transformation temperature from ß to a is raised with aluminum content. This effect is also typical of aluminum, in contrast with that found for the transition elements which lower the ß to a transformation temperature. Therefore, it may be anticipated that tprnarv titanium alloys with aluminum and any one of the transition elements will constitute a class of ternary alloys having characteristic features absent in alloys involving two transition elements. Chromium was chosen as a typical transition element for the present study because ternary alloys of Ti-Al-Cr commercially produced have been found to possess very interesting physical properties (MST-3 pct A1-5 pct Cr of Mallory-Sharon).'" Binary Systems The binary systems Ti-A1 and Ti-Cr have been established recently by several investigators. The data used in this investigation were taken from the complete diagram of Bumps, Kessler, and Hansen." This diagram agrees quite well with earlier investigations." For the Ti-Cr system, the phase boundaries at 1800" and 1400°F were taken from refs. 6 and 7. The binary system Cr-A1 has been studied recently by Bradley." This system is rather complex and contains not less than seven intermediate phases. The present study was limited to the titanium corner of the ternary system (less than a total of 40 pct Cr plus Al) and none of the phases present in the Cr-A1 binary alloys were found in the ternary alloys investigated. Experimental Technique Microscopic observation and X-ray diffraction measurements were used to identify phases and de-

Jan 1, 1954

By T. S. Hutchinson, C. E. Kemp

The bottom water drive analysis presented by Muskat has been extended to include fields with wider well spacings. Curves are presented from which volumetric sweepout, water-oil ratio, and rate relations may be calculated. The effects of non-unity ratios on sweepout eficiency and productivity decline have been studied by an approximate method. Also, the effect of gravity on volumetric sweepout has been approximated for a particurlar geometry. INTRODUCTION The purpose of this paper is to report work done in applying the analysis of bottom water drive reservoirs given by Muskat1 to a larger class of reservoirs, to extend this analysis to include the effects of gravity and non-unity mobility ratios in an approximate manner, and to investigate the rate of decline of productive capacity. The bottom water drive type reservoir is one where the oil is underlain by a water zone of sufficient thickness that water movement is essentially vertical. This system is defined in more detail in the appendix and a one well element is shown diagrammatically in Fig. 1. Muskat obtained solutions to the equations describing the volumetric displacement efficiency of idealized bottom water drive systems by assuming that gravity effects due to differences in density betwecn oil and water were negligible and that the mobilities of oil and water were the same. If either of these assumptions is not made, the complexity of the system makes an analytical solution well nigh impossible at the present stage of mathematical development. Coles and Stade' developed an approximation to consider these factors. The authors have refined approximations, starting with the same basic assumption, which should give a somewhat quantitative picture of bottom water drive performance when mobilities are not equal and the effects of gravity are not negligible. The results of these approximate calculations can then be used to obtain the decline in well productivity as the field is depleted.

Jan 1, 1957

By J. Szekely, J. W. Evans

A formulation is given for radiant heat loss from the surface of molten steel held in a ladle and numerical solutions are presented for the resultant integrodif-ferential equations. The results are shown on plots of the net rate of heat loss against time, with the geometlry, emissivities, thermal properties of the walls, and Preheat as parameters. It was found that the rate of the vadiant heat loss from the exposed metal surface was comparable to the conductive losses from the Portion of the metal in direct contact with the walls. The radiant heat loss was markedly affected by the geometry and by the thermal properties of the walls the net radiant heat loss from the steel could be drastically reduced by providing a top cover and also by the provision of preheat. The results of this work are thought to be relevant to heat loss calculatious concerned with vacuum degassing and with operatzons in which molten metals are held in ladles. WhEN molten steel is held or transferred in ladles heat losses inevitably occur. The accurate assessment of these heat losses is of importance in process design considerations, as the temperature of the metal may have to meet rigid specifications in certain stages of the processing sequence. As shown in Fig. 1, the principal mechanisms responsible for heat loss are: i) Conduction into the walls and ii) Thermal radation from the top metal surface (possibly augmented by natural convection) The conductive heat loss may be readily calculated as much information is available in the literature on both the general theory1'' and on its particular applications to ladle heat loss calculations. Evaluation of the radiant component of the heat loss is less straight-forward. In two recent papers it has been shown that the presence of a slag layer 2 to 3 in. thick would prevent any significant heat loss for periods up to an hour,5'" however, should bare metal be exposed, constituting the radiant surface, substantial heat losses could occur. This latter case is of considerable practical interest in various degassing operations and in the vacuum processing of certain specialty steels, where the top surface of the metal is not covered by a protective slag layer. Under these conditions a substantial radiant flux is emitted by the top metal surface; part of this flux leaves the system, part of it falls in the ladle walls. The radiant flux incident on the ladle walls is in part absorbed and conducted away, and in part reflected and re radiated. The purpose of the paper is to present a general formulation of the problem, the resultant solution of which should enable computation of the net radiant heat loss from the metal surface. The principal variables, the effect of which will be investigated, include initial metal temperature, geometry, thermal and radiative properties of the wall, and various modes of preheat. FORMULATION Consider a cylindrical enclosure, shown in Fig. 2, with a diameter D, height H, and wall thickness W, the cover at the top of the cylinder having a wall thickness L. If the temperature of the base (representing the top surface of the metal) is kept constant, say, Tb, the problem is to calculate the net rate of heat loss from the base as a function of time, geometry, the initial temperature distribution, and the thermal properties of the system. As customary, the formulation will consist of the mathematical statement of the conservation of thermal energy within the system.

Jan 1, 1970