Search Documents

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942

By C. Scala, M. Gondouin

Published laboratory data have established that very significant streaming potentials can exist across mud cakes subjected to pressure differentials such as exist between a mud column and formation fluids. Since shale is similar in kind and in properties to a well-formed mud cake, it appeared possible that streaming potentials might also arise across shales. A practical consequence would be that the streaming potential contribution to the SP would be smaller than might otherwise be assumed since the SP is measured with respect to the "shale bare line". The resultant contribution would be the difference between the streaming potential across the shale and that across the mud cake. In order to investigate this possibility, a laboratory apparatus was devised for measuring streaming potentials under pressure conditions normally encountered in wells. Reported data on streaming potentids across mud cakes were verified. More important, appreciable streaming potentials were found across shale samples. As in the case of mud cakes, the shale potentials varied with the concentration and nature of the impregnating electrolyte. Dependence on pressure was In a different rela-tion than that for mud cakes, possibly because of the lower compressibility of shales. The differences in streaming potentials between the shales md mud cakes were generally small, although they might vary considerably in practice depending on the relative electro-kinetic properties of the particular shale-mud cuke combination. A "poorly eflective" shale with a "very eflec-tive mud cake" would produce the largest negative addition to the electrochemical component of the SP. Results of field experiments with pressurized wells were considered in the light of the laboratory results. INTRODUCTION Field experiments wherein the pressure of the mud column in a borehole was varied have often indicated the presence of a streaming potential, but its magnitude was not easily predictable and its sign sometimes changed from one formation to another in the same well.' In the interpretation of SP logs from standard surveys, nevertheless, the correct value of R,, is very frequently obtained, within the limits of field accuracy, using only the simple electrochemical expression of the SP provided that proper corrections are made for bed thickness, ion activity, etc.' Accordingly, it was apparent that the streaming potential component of the SP in a borehole was considerably more complex than commonly assumed and clarification was indeed necessary The close similarity in nature and constitution of a shale to a well-compacted mud cake suggested that a streaming potential might also exist across shales as pointed out by M. P. Tixier in 1953 and as recently emphasized by Wyllie." e practical consequence would be that the streaming potential across the mud cake would be canceled, at least in part, on electrical logs since the SP is recorded with respect to the shale potential as a base line. This appeared to be a plausible explanation for many of the effects observed but no supporting data were available. In 1955 preliminary experiments at low pressures were conducted in our laboratories which supported the hypothesis of the shale streaming potential and formed the basis for later studies at borehole pressures.* EARLY LOW PRESSURE EXPERIMENTS The early experiments were conducted primarily to determine the possibility of a streaming potential across shales. The shale used was a compact type designated as No. 7 from Reagan County, Tex. (Permian). Cut samples were saturated for over one month in .2 to 2.0-N NaCl solutions. In order to eliminate all electrode polarization effects, a dynamic method was used. A transient pressure of about 1 atm was applied across

By D. R. Uhlmann, T. P. Seward, K. A. Jackson, J. D. Hunt

microscopic ohservations on alloys of organic trzaterials show that dendrite arms can melt off under normal conditiorzs of growth. This occurs because of the interactiorz of' heat and matter fluxes during dendritic growth. The re melting occurs where the den-drite arms are joined onto the main deizclrite sterrz. Many detached crystals can be produced in this fashion. It is postulated that this remelting phenornenon occurs in metal alloys, giving rise to the equi-axed region in castings. Experiments peyformed orr castings of transparent materials support remelting as a primary source of detached crystals. Ob~ervations an equiaxed tones in metal castings are discussed in terms of this and other mechanisms. It is concluded that the partial remelting of dendrites is on important mechanisnl for producing the equiaxed regions in castings. THE freezing of a casting can be divided into three regions: a chill zone formed near the mold wall, a columnar region, and a third region, at the center of the casting, which is called the equiaxed zone. The origin of the grains that comprise the equiaxed region is the subject of this paper. We will first outline the mechanisms which have been proposed to account for the origin of the equiaxed region and discuss some recent experiments which cannot be explained by these theories. We will then present some microscopic observations of dendritic growth which have led us to conclude that the equiaxed zone in castings can arise from partial remelting of dendrites. This proposal is supported by observations on transparent castings. Finally, we will discuss several observations on metal castings which could not be explained previously, and which can be accounted for by the present proposal. Previous Mechanisms. Winegard and Chalmers3 pointed out that the molten central region of an ingot could be constitutionally supercooled, because of the solute layer at the growing interface. In this supercooled region, nucleation on particles could occur, giving rise to the equiaxed crystals. Another mechanism has also been suggested,4y5 that the nuclei originate in the chill zone then float or are carried by convection to the center of the casting, where they grow to produce equiaxed crystals. In this case, all the crystals nucleate immediately on casting, so this mechanism will be termed "big-bang" nucleation. Walker's Experiments. J. L. Walker has made observations on the solidification of nickel and Ni-Cu alloys which cannot be accounted for by either of the above mechanisms. In studying the grain size resulting from freezing of nickel at various undercoolings, walker6 found that at large undercoolings the grain size was small, due to mechanical nucleation, as discussed by walker7 and Horvay.' At small undercoolings, the grain size was large, and the growth dendritic. In Ni-Cu alloys, however, for initial undercoolings starting from just below the melting point and extending for a hundred or so degrees of undercooling, fine grains were also observed. Samples were undercooled 200 Centigrade degrees without nucleating, and were then heated 130 Centigrade degrees so that the undercooling was 70 Centigrade degrees, and nucleated. The samples had a small grain size, indicating multiple nucleation. There were no heterogeneous nuclei in the liquid which could operate at the temperature of growth. Constitutional supercooling could not have been greater than the supercooling of the initial melt, since the temperature rose as the freezing continued. walker -as also shown that a Ni-Cu alloy which can be undercooled to below its solidus will produce typical columnar and equiaxed regions when cast into a cold mold. This alloy could not reach a temperature below its solidus by constitutional supercooling. It could not, therefore, have nucleated heterogeneously. Neither the big-bang mechanism nor the Winegard-Chalmers mechanism can account for the fine grain

Jan 1, 1967

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable-shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 2, 1914

By J. A. Brierley, Roshan B. Bhappu, D. H. Reynolds, P. H. Johnson

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientifi research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump-leaching process and discusses salient features and parameters that may be helpful in improving such operations. The dump leaching of low-grade copper ores, as an integral part of the open-pit mining operations in the Southwest, has been practiced for the last 50 years and is increasing in importance as one of the major sources of copper. The recent acceleration in dump leaching can be attributed to: (1) the greater tonnages of low-grade ores mined and dumped at newer mines as well as resulting from increased stripping ratios at the older mines, (2) the relatively small investment required for dump leaching facilities per pound of copper recovered contrasted with expansion of milling facilities to recover equal amounts of the metal by raising tonnage throughout, (3) low labor requirements needed for leaching, and (4) the simple and continuous nature of the process needing little close supervision of trained operators. In the past, the mining companies have not worried about efficiency in dump leaching but have been satisfied with whatever metal recoveries could be made without much effort. However, because of the huge amounts of metal accumulating in the low-grade waste dumps, compared to the relatively small amount recovered annually, an operator today cannot leave dump leaching to chance. What appears to be a simple, empirical process is actually a very complex one involving a large number of critical factors that encompass Several Scientific disciplines, such as physics, chemistry, geology, biology, and hydrology. It is imperative that

Jan 1, 1970

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,' and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6'7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.' EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.' Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

By Fred L. Morritz, Harold M. Manasevit, Richard Nolder, Arnold Miller

Experimental evidence is presented which confirnis the epitaxial relationship between the deposited silicon and the sapphire substrate. Four distinct modes of orientation relationships have been established. These have been shown to be Single-crystal gvowth retention as a function of surfaces oriented off ideal has been qualitatively indicated. Both full-circle goniometer X-ray techniques and replica electron microscopy have indicated varying amounts of microtwinning in the silicon. film, which may he caused by the mode of silicon formation. Parameters have been found where twin density is less than I pct. The early stages of' epitaxy of silicon m sapphire have been examined by electron-microscope techniques... and mechanisms have been proposed. THE first report of the deposition of single-crystal silicon on sapphire (single-crystal aluminum oxide) was made at the American Physical Society Meeting in Canada' by one of us and was subsequently published in the Journal of Applied physics.* This paper summarizes some of the work carried on in this area since that time, in addition to reviewing some of our earlier observations. The initial single-crystal deposits of silicon on sapphire reported were obtained on sapphire planes produced by cutting a sapphire rod perpendicular to its fastest growth direction, which is approximately 60 deg from the C axis. Direct correlations between the microstructure and X-ray data as to the single crystallinity as shown in Fig. 1 are evident. These deposits were identified as (111) silicon on the substrate oriented near the (1123) of sapphire. (Sapphire notations are designated according to the c over a ratio of 2.73.) It became evident that substrate quality and surface play an important part in successful epitaxy. For example, in Fig. 2 we observe an interesting

Jan 1, 1965

By Herbert Clark Hoover, Lou Henry Hoover

DIFFERENT methods of parting gold from silver, and, on the other hand, silver from gold, were discussed in the last book; also the separation of copper from the latter and further, of lead from gold as well as from silver ; and, lastly, the methods for refining the two precious metals. Now I will speak of the methods by which silver must be separated from copper, and likewise from iron.1 The officina, or the building necessary for the purposes and use of those who separate silver from copper, is constructed in this manner. First, four long walls are built, of which the first, which is parallel with the bank of a stream, and the second, are both two hundred and sixty-four feet long. The second, however, stops at one hundred and fifty-one feet, and after, as it were, a break for a length of twenty-four feet, it continues again until it is of a length equal to the first wall. The third wall is one hundred and twenty feet long, starting at a point opposite the sixty-seventh foot of the other walls, and reaching to their one hundred and eighty-sixth foot.

Jan 1, 1950

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,' Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,' Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,' Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,' Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

By Harrison Schmitt

During the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. Hanover, New Mexico The Hanover, New Mexico, zinc deposits were briefly described by Lindgren and others,' Paige2 and recently in more detail by Schmitt. These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive ¾ mile wide and 2 miles long (Fig. I). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike, thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1935

Boundary and general corrosio~z rates for higkpurity alutninum were ~rzeasured irz 16 pct HC1 at sJmllow penetrations (< 25 p). The rates for several high-angle random tilt boundaries, several [001] synzmetrical tilt boundaries, a 54-deg [010] twist, and a 15-deg randorn tw~st boundary were one-fourth to one-third higher than that of the (001) surface used as reference. Boundary attack was slower for 23 and 37-deg [001] tilt boundaries and a 16-deg [010] twist boundary. The corrosion rate for a (111) surface was roughly om-third higher than for (001) and was thus about as high as the corrosion rate of the fastest boundaries. The boundary attack did ?lot appear to parallel the variatiorz of boundavy energy. The signvicance of the anisotropy of corrosion was discussed.

Jan 1, 1966

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By K. A. Svanstrom, W. R. Opie

Problems associated with deposition of titanium infused chloride baths using TiCl4 as a feed material are reviewed. A potentially workable cell design using Alumdum diaphragms is discussed. Problems inherent to diaphragm-type cells are emphasized and experiments described which led to the development of a cell without a diaphragm. INVESTIGATORS assigned the problem of developing a commercial electrolytic process for making titanium metal have found that they are faced with the difficulty of overtaking rapidly improving magnesium and -sodium reduction processes. The ultimate goal must be a simple process that can be conducted with low-cost raw materials in equipment that is inexpensive to build and operate. This paper deals with some work of a preliminary nature conducted by personnel of the Research Laboratories, National Lead Co., Titanium Division. Many others have reported on the general subject of depositing titanium from fused salt electrolytes. A partial bibliography is attached. PRIMARY CONCEPTS Anyone attempting to deposit titanium metal from fused chloride electrolytes using TiC14 as a source material is faced with at least the following problems: 1) Getting the titanium into solution in the bath. 2) Controlling oxidation and reduction reactions associated with multiple valency of titanium, which result in low electrical efficiency. a) Prevention of dichloride oxidizing to trichloride and trichloride to tetrachloride at the anode. b) Prevention of trichloride from being reduced only to dichloride at the cathode. 3) Prevention of metal formation away from the cathode thru disproportionation of titanium dichloride to satisfy the equilibrium. 3 TiCl2 == 2 TiCl3 Ti [I] 4) Protection of reduced chlorides in the bath from reaction with oxygen from the bath container or air. 5) Removing from the bath the deposited metal formed without allowing it to become contaminated with oxygen or nitrogen. 6) Selecting cell materials of construction which will not contaminate the metal product or cause cell inefficiencies. EARLY EXPERIMENTS The initial attempts made to electrodeposit titanium from fused chloride baths using TiCl4 as a source material indicated that TiCl4 was essentially insoluble in molten chlorides of alkali and alkaline earth metals. If, however, the TiCl4 was introduced close to a nickel cathode some metal could be formed and appreciable quantities of reduced chlorides would be present. These reduced chlorides reacted with any oxygen present in the atmosphere above the bath and would also diffuse quickly to the anode (graphite) where they would react with chlorine and be evolved as TiCl4. The net electrolytic efficiency of such a cell is essentially nil. The TiCl4 evolves from the anode at almost the same rate that it is introduced in the vicinity of the cathode although a small amount of titanium metal can be formed on the walls of the cathodic pipe. It becomes apparent from the operation of such a cell that: metal can be deposited on the cathode, although of small particle size and a nonadherent nature, and when reduced chlorides are present in the electrolyte, TiCl4 can be absorbed, probably by the following reactions: TiCl4 + TiC12 - 2 TiCl3 [21 2 TiCl3 + 2 faradays - 2 TiC12 + C12 [31 DIAPHRAGM CELLS These facts encouraged the development of cells containing diaphragms to prevent migration of reduced chlorides from the cathode area to the anode. Small-scale cells for process development are described by Alpert, Schultz, and Sullivan.20 A larger brick-lined cell incorporating internal heating by passing ac through the bath is shown in

Jan 1, 1960

R. G. BROWN, Bodie, Cal.: Mr. Rickard&apos;s paper, with its valuable illustrations, brings into fresh clearness the game of hide-and-seek which the miner must play with his ore-deposit; but, more than this, it goes far towards classifying those perplexing idiosyncrasies which, while unclassified, constitute a labyrinth almost without clue. Probably every engineer can add to the list by the mention of at least one fresh detail from his own experience, and I for one would like to comment on two of Mr. Rickard&apos;s divisions. To what he has written about " walls within walls" and " walls without walls," the accompanying Figs. 1 and 2 may be appropriate, the more so as they represent conditions obtaining in a part of the Butte copper-belt more typical of the copper-veins as a whole than the Gagnon, which, in some respects the most interesting mine in the camp, stands almost alone in many particulars. (See nuns., xvi., 62.) Fig. 1 was sketched in January, 1895, in the stopes above the 700-foot level of the Colusa-Parrot mine, east of the Parrot and southwest. of the Anaconda. The stope, the commercial foot-wall of which is shown at A, was 30 feet wide at this section, the pay-ore being massive chalcocite, jumbled with bornite, pyrite, quartz and thoroughly broken-down granite. A and At are inch-thick seams of black talc; B, B&apos; and B" are also talc, possibly 1/8-inch thick. In the plane of the section the "banded quartz " and " quartz and pyrite " were both of too low grade for extraction, but 5 feet back along the stope had been of fair value. The granite with quartz and bornite between Bt and A&apos; was pay-ore, but that to the right of B" was not. In both cases the ferro-magnesian minerals had been removed, leaving, where not obscured by ore, faint, dark patches. Between A&apos;

Jan 1, 1897

By H. LeChatelier, B. Bogitch

Page Introduction........................... 134 Methods of Investigation....................... 135 The Tridymite Network...................... 137 Independent Variables....................... 146 Manufacturing Operations..................... 153 Introduction Silica brick are indispensable in the manufacture of steel because they alone are able to withstand the high temperature of regenerative furnaces. All attempts to replace silica brick by other refractory materials for this purpose have failed, but the reason for this failure has remained obscure; we shall give an explanation later in this paper. Before the war, silica brick employed in France came principally from abroad, for which reason, since the beginning of hostilities, certain French steel works have been seriously handicapped. Our attention was first directed to the question by M. Bied, Engineer of the Teil Works. With him, we began certain investigations, at first using our laboratory and the furnaces of neighboring steel works. The larger part of our experiments, however, have been made in the laboratory of the Faculty of Sciences at the Sorbonne. For the heating of our samples, we are deeply obliged to MM. Charpy, Yeatmann and Guerineau. In undertaking these studies, our first aim has been to render assistance to French industry, by indicating, as precisely as possible, the necessary conditions for the manufacture of high-grade brick; but at the same time me have

Jan 1, 1919

By Gerald Edmunds

CASTINGS of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, some-times nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is devel-oped to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and there-fore the position of the grains is more com-plex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicat-ing that thermal contact was better there than in neighboring areas.

Jan 1, 1940

By M. J. Marcinkowski, A. Szirmae, R. M. Fisher

Room -temperature hardness measurements obtained from single and polycrystalline samples of a 47.8 at, pet Cr-Fe alloy which were aged for various times al 500°C show a two-fold increase over that of the unaged alloy after annealing for 1000 hr. A detailed examination of the deformation markings in the neighborhood of the hardness imbressions reveals that twinning becomes an increasingly more important mode of deformation as aging proceeds. this observation is shown to be inconsistent with the Proposals that the transformation is eve of order-disorder On the other hand, the results are in agreement with previous observations of Fisher et al. of a coherent chromium-rich precipitate which forms in an iron-rich matrix as a result of a miscibility gap in this alloy system as proposed by Williams . Using the coherent precipitate hypotlzesis as a model, a detailed analysis of the various possible strengthening contributions to both the slip mid twinning stresses is made. In the case of&apos; slip, lattice friction within the chromium-rich phase and the chemical energy associated with the interface between the two phases contribute about 60pet to the total strength. The contributions from coherency strains and modulus differences are thought to contribute the remaining 40 pet of the strength but are difficult to evaluate because of uncertainties regarding the flexibility of the dislocation line. All of the factors have nearly the same or else a smaller effect on the twinning stress in the aged alloy. Twinning is never observed in the unaged alloy because the twinning stress is much higher- than that for slip. With increased aging times, the various contributions to the total stress for both twinning and slip increase, but most of those for slip increase much more rapidly, so that, in the fully aged alloy, it surpasses the stress for twin propagation. When a twin is nucleated by the chance occurrence of an internal stress concentration during a test, the subsequent twin burst results in a low hardness reading. FeRNTIC Fe-Cr alloys from about 15 to 80 at. pet Cr content show considerable change in properties such as hardness, electrical resistivity, saturation magnetization, and so forth, after aging in the vicinity of 500°C.* The most marked change is a large increase in hardness accompanied by a sharp decrease in ductility, so the phenomenon has often been referred to as the 475°C (885°F) em-brittlement problem. Changes in microstructure are rather subtle and most investigators have not been able to observe any X-ray diffraction or metal-lographic changes during aging. There is little doubt that the phenomenon is inherent to the Fe-Cr binary system and is not directly related to the formation of a phase. Two distinct schools of thought have developed during the past decade concerning this problem. Masumoto, Saito, and sugiharal have concluded, from their own specific-heat measurements, that atomic ordering occurs in this temperature range. Pomey and Bastien2 have also attributed the changes in physical properties with aging in the neighborhood of 500°C to atomic ordering. In addition, Takeda and Nagai3 claimed to have found X-ray verification for superlattices corresponding to the compositions FesCr, FeCr, and FeCr3. However, all known attempts to observe superlattices in Fe-Cr alloys using neutron diffraction, which should be much more sensitive, have been unsuccessful. These have been reported by Shull et al.4 for 25 at. pet Cr, williams5 for 75 at. pet Cr, and Tisinai and samans6 for a 28.5 at. pet Cr. steel. The second and more prevalent opinion ascribes the 475°C embrittlement phenomenon to the formation of a coherent precipitate due to the occurrence of a miscibility gap in the Fe-Cr system below about 550°C. This latter concept was first indicated by the results of Fisher, Dulis, and Carroll,7 who were able to extract fine particles about 200Å in diameter from samples of 28.5 at. pet Cr steels aged from 1 to 3 years at 475°C. The extracted material was found to be nonmagnetic, to have a bee structure with a lattice parameter between that of iron and chromium, and to contain about 80 at. pet Cr. Williams and paxton8 and williams5 confirmed these results and first explicitly proposed the existence of a miscibility gap below the a region in the equilibrium diagram. Alloys aged within this gap

Jan 1, 1964