Search Documents

By Nicholas J. Grant, John Chipman

A FULL understanding of the behavior of sulphur in the basic open-hearth process has been delayed by lack of dependable data covering a wide range of slag conditions in the absence of other complicating factors that are likely to be present under operating conditions. It has been generally accepted that strongly basic slags will dissolve more sulphur than will those in which the acidic and basic constituents are more nearly balanced. It has been known that both slag and metal would absorb sulphur from the flame when the sulphur content of the fuel is high. It has been generally believed that manganese assists in the transfer of sulphur from metal to slag. Almost nothing has been known of the effect of temperature upon desulphurization; the data have been conflicting and there has been a tendency to depend rather heavily upon analogy with the better understood desulphurizing reaction of the blast furnace. Many attempts have been made to build up from open-hearth data a satisfactory theory of the chemical reactions involved in the process. That this has been an extremely difficult task is owing to two reasons that have been very generally recognized. The first is the parallel and simultaneous reaction of sulphur transfer between flame and bath. The second is the difficulty of distinguishing between the factors that ultimately limit the transfer from metal to slag-i.e., equilibrium conditions-and those whose influence is only upon the rate of transfer. It has been the object of the work here recounted to study the equilibrium distribution of sulphur between slag and metal in the absence of these complicating factors, with the hope that a better understanding of the equilibria involved would lead to a better control of the over-all process in the open-hearth furnace. A review of the literature on steelmaking reveals almost complete agreement with respect to the paramount importance of lime in promoting desulphurization. In expressing this effect in quantitative terms, however, and in formulating the relationships between the concentrations of other slag components and the desulphurizing power, there is little agreement. For instance, the "basicity" or basic strength of the slag is commonly measured by some kind of ratio of concentration of basic to acidic oxides. Of these, the following have been reviewed by Schenck :20 [ ] Among others there appear the following:

Jan 1, 1946

By Giovanni B. Barla, Stefan H. Boshkov

The block caving method is examined in this paper on the basis of experimental results and observations in the field, and through the use of numerical modeling by the Finite Element Method. The Grace Mine, developed by a panel caving method, served as a reference case. However, the results obtained and the simulation techniques which have been developed may find useful application in more general conditions as encountered in other mining operations by block caving. Following a brief description of the Grace Mine and of the mining method, the problems associated with the behavior of underground drifts at the production levels, during undercutting and caving, are addressed. The most important results obtained through monitoring of strains and loads in the supports of a runway are discussed, while giving relevance to the sequence of mining operations in the immediate vicinity. The most important geomechanical data, as provided for subsequent modeling, are described with reference to: (a) rock mass characterization and (b) in situ state of stress. Then, the numerical modeling procedures, developed by the Finite Element Method in order to predict the caving phenomena and the behavior of underground openings during undercutting, are discussed. Finally, an attempt is made to compare the pre- dictions of the numerical analyses with, the measurements carried out at the instrumented site. Suggestions as to how to improve the results both qualitatively and quantitatively are also given.

Jan 1, 1984

By D. E. Menzie, D. L. Dauben

This paper discusses the physical parameters involved in the slow flow of high molecular weight polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. Experiments were conducted with the polyethylene oxides, with molecular weights ranging from 200,000 to over 5,000,000. Frontal advance velocities ranged from I to 30 ft/day. The porous matrix consisted of a flow cell packed with glass beads. Polymer solutions were characterized by viscosity and normal stress measurements. Under certain conditions, unexpectedly high flow resistance was observed. This behavior was observed to be a function of flow rate, pore size, polymer molecular weight and concentration. The polymer solutions exhibit "dilatant" flow behavior in porour media in contrast with the pseudo-plastic behavior in simple flow systems. A theoretical ex-planation of such behavior is presented. INTRODUCTION The use of polymers in the injected water of a waterflood increases oil displacement efficiency by reducing the mobility (k,/pu) of the driving phase. A reduced driving phase mobility results in improvements in the areal sweep efficiency and in the vertical coverage in stratified reservoirs. This mobility reduction may be achieved by a permeability reduction, a viscosity increase or by a combination of the two. Early attempts at increasing the injected water viscosity were not successful because of the poor economics involved. The use of such materials as glycerin, sugar or glycols to increase water viscosity was not economically feasible. Attempts in using certain naturally occurring polymers were not too successful because of the high polymer losses to the rock. A high molecular weight, partially hydrolyzed polyacry-lamide was introduced 3 years ago as a waterflood additive.',' Initial work by Pye' indicated that the presence of these polymers in dilute concentrations decreases the water mobility 5 to 20 times more than would be expected from measurements of the solution viscosity. Such an effect would be of obvious economic value since only a small polymer concentration would be required to accomplish a large reduction in water mobility. This research was designed to study the basic flow mech anisms of polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. This study indicates some of the conditions under which these interactions can lead to significant mobility effects. is valid only for Newtonian fluids. For polymer solutions and other non-Newtonian fluids the equation must be modified to consider that viscosity is a variable quantity. Modification of the Darcy equation to include non-Newtonian effects has been the subject of several recent investigations."" The modifications generally adopt a rheological model. such as an Ellis or Dower law model. to Dorous media by defining some characteristic channel radius. Most of these studies showed the porous media flow behavior to be predictable from viscometric data. Investigations involving the flow of high molecular weight polyacrylamide solutions through cores have generally encountered the high flow resistances reported previously by Pye. This high flow resistance has generally been attributed to an in-depth permeability reduction, as evidenced by a reduced permeability to water which has displaced polymer solution from the porous media. Marshall and Metzner" report high flow resistances, which they attribute to viscoelastic effects. In this paper, the effects of polymer molecular weight, pore size, flow rate and concentration are considered. The polymers used are the polyethylene oxides known as Poly-ox. This class of polymers was used because of its availability in a wide range of molecular weights and because of its known ability to propagate well through porous media. THEORY PHYSICAL PROPERTIES OF POLYMER SOLUTIONS The polymer molecule dissolves in water by means of hydrogen bonding, but retains some of its own structural identity while in solution. Nonionic polymers, such as polyethylene oxide, are generally considered to have a random coiling configration. This type of molecule has the ability to "sequester" or hold a large volume of solvent within its coils in a manner similar to that of a sponge. The random coil is easily deformed and under an applied stress

By D. J. MacKinnon, J. M. Brannen

Smooth, compact, dendrite free 24-h zinc deposits have been electrowon from zinc chloride electrolyte using a diaphragm cell. The cell consisted of sealed anode compartments containing DSA anodes separated from an open cathode compartment by Dynel cloth membranes. Fresh electrolyte was fed to the cathode compartment where zinc deposition onto an aluminum cathode was aided by air sparging. The catholyte passed through the diaphragms into the anode compartments from which chlorine gas and spent anolyte were withdrawn. Standard electrolysis conditions were: 15 g/L Zn, 0.12 M HCI, I5 mg/L tetrabutylammonium chloride (TBACI) as the addition agent, 35°C, and 323 A/m2 (30 ASF) current density. The effect of variations in these conditions on the morpohology orientation, current efficiency, and energy requirement for 24-h zinc deposits was determined. The effect of total chloride ion concentration on the zinc deposit was studied by adding various amounts of NaCl to the electrolyte.

Jan 1, 1983

By R. Wiesenthal

A method is developed for improving the low recovery efficiency which results when viscous oils are flooded by water. Viscous oil has been diluted with a lighter liquid miscible in it in any ratio which produces a mixture possessing a reduced viscosity and which is then displaced by water. Light gasoline was used in these tests to reduce the viscosity of the oil in place. Oils possessing viscosities in the range of 1.28 to 324 cp at the test temperature of 30C were displaced from a cylindrical unconsolidated sand core, with a length of 2 m (6.6 ft) and a diameter of 10 cm (3.9 in.) at a flood of 6.27 cc/sq cm/hr. In two test series up to I PV of light gasoline was injected into the core before water flooding. In the first series the recovery of a low-viscosity oil (1.28 cp) increased as the volume of light gasoline was increased. However, only the oil which could not be recovered by water flooding alone could be replaced by the light gasoline. In the other series, the recovery of a more viscous oil (13.5 cp) was not increased even if large quantities of light gasoline were injected. An oil bank built up ahead of the water front so that the flood water met with equivalent saturation conditions, as would be the case in flooding solely with water. However, the recovery of more viscous oils could be increased substantially when the core was first flooded with water, followed by a slug of light gasoline, and then flooded with water again. Furthermore, an oil bank ,built up ahead of the second water front. The formation of this oil bank is particularly favorable for the displacement process; the greater part of the light gasoline injected was pushed out of the core ahead of the oil and recovered. Using a light oil of low viscosity, it was possible to replace only the residual oil that could not be recovered by water flooding by the light gasoline. As the basic study had shown that highly viscous oils could be recovered by flooding first with water, then with light gasoline, followed by a second injection of water, the study was extended by tests made with reservoir fluids and cores taken from the low-gravity oil reservoir of the Wietze field, Germany. A great increase in recovery over flooding with water alone was obtained in these tests. The results may show a way to recover high-viscosity oils by a comparatively simple flooding procedure. INTRODUCTION In fields where oil recovery has not benefited from natural water drive, increased recovery may be obtained by the injection of water into the reservoir, especially in the case of fields which produce high-gravity, low-viscosity oil. There is a rather close relation between the viscosity of the reservoir fluid and the recovery that can be obtained by water flooding. As the viscosity increases the oil recovery decreases proportionately, so that an oil viscosity about 30 times that of water is generally considered to be the upper limit for an economically successful water flood.' This limitation has been recognized theoretically by Buckley and Leverett,' and has been verified by numerous laboratory flooding tests, such as by Croes and Schwarz,V n the viscosity ratio range of oil to water from 1 to 500. The reason for the inferior recovery of viscous oils by water flooding can best be understood by considering the mechanism of flood tests. In such tests water is introduced into one end of a sand-packed tube which is saturated with oil of the viscosity to be tested, and oil is produced from, the other end. Oil, with a viscosity lower than that of water, is pushed ahead of the advancing water with considerable uniformity, and irregularities in the displacement process tend to be eliminated as the oil saturation decreases and the water saturation increases. However, oil recovery is not complete, for the water forms interfaces with the oil and traps residual oil droplets in certain of the pore spaces. These residual oil droplets are distributed rather uniformly through the sand, and they are not susceptible to recovery regardless of the amount of water passed through the test cylinder. In the case of an oil possessing a viscosity greater than that of water, the injected water tends to move irregularly through the sand in the test cylinder. At the place in the sand where initial water movement takes place, resistance to the movement of water is lowered and the water finger so formed will grow perceptibly; it will extend to the outlet end of the test cylinder so that a breakthrough of water takes place long before much of the oil-saturated volume of the sand has come in contact with water. Once the breakthrough of water takes place, the water-oil ratio is gradually approaching the economic limit, even though much of the oil in the test cylinder remains unaffected by water. Disconnected drops of oil are trapped in the portion of the sand that has been invaded by water, just as when an oil of low viscosity is flooded. The poor recovery of the more viscous oils, therefore, is due to the irregularity of water movement through the test cylinder, and the rate of water movement through restricted sections of the oil-saturated sand increases with the more viscous oils. There are three ways whereby the recovery of viscous oils by water flooding can be improved:' (1) adding materials which will increase the vis-

Jan 1, 1965

Sec. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whom residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the claw of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1944

By Robert Henderson

SEVERAL very interesting articles have been written on the caving system of mining, but most of these papers have dealt separately with the slusher system or the chute and grizzly system. In this paper, a comparison will be made of the two methods, both of which are being used at the Climax mine. The mine is on the Continental Divide, in central Colorado, at an altitude of approximately 11,500 ft. above sea level. The long, cold winters, characteristic of the high Rockies, create a number of operating problems not usually found in other mining areas. THE ORE BODY The Climax ore body is just east of the Mosquito fault. This structural deformation has brought the granite on the east against the sedimentary rocks on the west. The ore occurs in an intensely altered granite and schist around a silicified granite core. The ore is in a highly fractured zone of moderate silicification. The principal mineral, molybdenite, is found in these fractures. Barren dikes of granite porphyry cut through the ore body and core with no apparent regularity. The grade of the ore is fairly uniform and gradually decreases toward the footwall core and also into the hanging-wall granite. The footwall and hanging wall are determined entirely by assays. The ore body is roughly dome-shaped, with the apex truncated at the surface. It is covered to varying depths with talus. A horizontal section of the ore body on the Phillipson level appears as an annular ellipse surrounding the footwall core. The ring of ore varies in width from 300 ft. to as much as 800 ft. The north-south axis of the core is about 1200 ft. and the east-west axis is about 1800 ft. In the ore zone, the rock is sufficiently strong to maintain reasonably large openings, and openings larger than haulage drifts usually have to be supported. The ore is cut by a great many fractures and shears and breaks into rather large blocks when caved, necessitating considerable secondary blasting. The waste that overlies the ore body breaks relatively fine in comparison with the size of the blocks of the caved ore and tends to run through the broken ore in the cave, causing dilution unless the draw is carefully controlled. MINING SYSTEMS For several years the ore was mined by the chute and grizzly system, a system that differs from that used in other caving mines only in the size of openings and equipment. In the chute and grizzly system, main haulage laterals were driven along the footwall core and also along the

Jan 1, 1944

By A. W. Gauger

Coal as mined contains varying quantities of inorganic components (mineral matter) which, on combustion, produce the residue known as ash. It has long been realized that the weight of this residue does not equal the weight of the mineral matter originally in the coal, because of the chemical changes that take place during the ashing process. Moreover, the ordinary ash analysis presents the ash as a mixture of oxides with little or no clue to the identity of the mineral species originally present in the coal. It is only for pyritic sulfur that an attempt is made to determine a mineral component. So far as the authors are aware, there are practically no experimental data in the literature as to the percentages of the different mineral species present in coal. The oft-quoted table of Marson and Cobb1 cannot rightly be considered as data, since the authors merely state that the table "shows the probable forms in which these ash constituents exist in coal." In view of the attempts to calculate analyses and determinations of the calorific equivalent of coal to the mineral-matter-free basis, as well as the importance of the mineral species in clinkering, combustion and coking, it seems strange that so few data are available on this phase of coal technology. For example, numerous empirical corrections for use in the scientific classification of coal have been suggested to compensate for the losses from the mineral matter during ignition of the coal to ash. These include multiplication of the ash percentage by various factors such as l 1/10 and 156, the use of the Parr unit coal formula (1.08 A + 22/40 S, where S = total sulfur) as well as certain modifications of the Parr formula that attempt to correct for the organic sulfur present in the coal. Although many experiments have been made to determine the loss on ignition of the clays associated with the coal measures and correction

Jan 1, 1934

By B. Fitch

This paper deals with the behavior of sedimenting suspensions. More particularly, it treats, in as organized a manner as possible, the body of knowledge, theoretical or empirical, by which one predicts the behavior of miscellaneous swarms of particles in suspension. Such knowledge is necessary for precise and economical design of equipment. While the behavior of a single spherical particle settling through an infinite sea of quiescent fluid is well understood, practical sedimentation processes are almost always concerned with particles of assorted sizes, densities, and shapes, in such concentration that there is profound particle interaction. Such swarms of particles are observed to settle in any of four markedly different manners. Which one they follow is governed by particle interaction. It is determined largely by the dilution of the suspension, and the relative tendency of the particles to cohere. TYPES OF SEDIMENTATION The relationship between the different modes of sedimentation is shown paragenetically in Fig. 1. The left side of the diagram represents particles having little tendency to cohere; the right side represents particles for which interparticle cohesion is large compared to the settling force. The vertical axis represents dilution. As seen in the diagram, sedimentation is divided into three broad fields or regimes. At high dilutions there exists a regime here named 'clarification.' Particles in clarification may settle either individually, or by collecting into separated floccules. Thus there are two different possible modes of settling in the clarification regime. It is characteristic c~f this regime that there will be no clear line of demarcation between settling suspension and a supernatant. Faster particles settle out ahead of slower ones. In batch tests there develops a gradation of both particle sizes and pulp density due to progressive depletion of the largest particles from any given pulp level.

Jan 1, 1962

By Guy W. Jordan, David P. Hale

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942

By David P. Hale, Guy W. Jordan

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942

By D. M. Kehn

A method has been devloped for chromatographic analysis Of the vapor and liquid phases Of a a system containing methane to components having 20 or more carbon atoms. The method uses a windowed equilibrium cell in which volumetric phase behavior of the system can be observed accurately and from which small samples of gas or liquid can be withdrawn for analysis. Analyses are made using two chromatographs, one for the lighter and one for the heavier components in a sample. Combination of the two analyses yields a detailed analysis of the gas or liquid sample. The complexity of the condensate heavy ends is evident from the chromatograms of these fractions, and the predominance of the paraffin hydrocarborn serves as a useful marker in interpreting the chromatograms. The K-values obtained in this analytical method are presented for a high-pressure condensate system and predict closely the observed volumetric behavior of the system. INTRODUCTION Quantitative analysis of hydrocarbons from natural gas reservoirs is necessary for several reasons—to calculate the amount of sales gas produced, to calculate the amount of natural gasoline produced, to plan a liquid recovery system, or to calculate the potential economic value of a reservoir produced under one or more of several different conditions. Analysis of natural gas fluids produced to the surface consists of identifying and computing the mol fraction of each component of the mixture. Although methane is the predominant component, varying amounts of ethane, propane, butane, pentanes and heavier components are also present. Materials containing up to 30 carbon atoms occur in amounts which decrease with increasing molecular weight. However, the quantities of components in the 20 to 30 carbon atom range are usually so small that their importance is negligible, and they are undetect-able in natural gas by ordinary analytical methods. All the components up to those having 20 carbon atoms may sigsficantly affect phase behavior, however. Commonly, only the methane-through-pentane fraction is analyzed quantitatively for each component, while components heavier than Pentane are lumped and repored as "hexane- plus". Expensive, tedious techniques are required for analysis of this fraction. Consequently the detailed analyses needed for prediction of reservoir behavior are usually undertaken only when major gas fields are being developed. The need for complete analyses of condensate systems is apparent when it is recalled that most gas fields are produced by pressure depletion. As the pressure declines, some of the heavier hydrocarbons are lost as liquids which are in the reservoir. In many instances the amount of liquid in equilibrium with the gas phase at high pressure constitutes only 1 or 2 mol per cent of the total system. Flash calculations generally must predict the actual amount of liquid with an accuracy of a few per cent in order to be useful. This retrograde condensation has been understood for years, but accurate correlation methods to permit quantitative prediction of phase behavior in the retrograde region are not presently available. The increasing importance of natural gas has made accurate prediction of phase behavior and composition of produced natural gas streams an economic necessity. The work reported here was undertaken to provide a rapid, economical method for obtaining the vapor-liquid equilibrium information needed to predict accurately the composition of the fluids produced from a gas reservoir throughout its life. TO develop this method, a pressure cell equipped with windows was designed and built for observing the volumes of liquid and gas present at reservoir pressures and temperatures. Use was made of established chromatographic methods for rapid and detailed analysis of both phases. This paper describes the equipment and techniques developed for obtaining vapor-liquid equilibrium data, presents the results of analyses of a condensate system, and indicates the usefulness of these data in predicting hydrocarbon phase behavior. DESCRIPTION OF EQUIPMENT USED The equipment used in obtaining the required information on phase behavior and the complete analysis of hydrocarbon mixtures through C, will be described first, followed by a discussion of the operation of the equipment. It will be helpful, however, to consider first a brief outline of the technique used. A sample of separator gas and liquid is charged to the windowed cell (see Figs. 1 and 2) where volumetric equilibrium phase behavior at reservoir pressures and temperatures can be determined. Then samples of the coexisting phases are withdrawn. The methane-through-pentane fraction is analyzed with a chromatograph equipped with a hot-wire detector, and the pentane-plus fraction is analyzed with a second chromatograph equipped

Jan 1, 1965

By Arthur F. Colombo

The selective - deslime - flotation process developed by the Federal Bureau of Mines as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The operating parameters for the selective flocculation - cationic flotation of oxidized taconites from the western Mesabi range in Minnesota are discussed. Data from the operation of a 410 kg/hr (900 lb/hr) pilot plant employing reclaimed water are summarized for 2 types of oxidized taconites.

Jan 1, 1979

By Eugene N. Cameron

Graphite is the hexagonal form of crystal-line carbon. It is found in nature locally as tabular crystals but occurs mostly as disseminated flakes, foliated, platy, or fibrous masses, or microcrystalline compact to earthy material. Graphite is characterized by its gray to black color, metallic luster, black streak, perfect basal cleavage, softness (H = 1-2) and unctuous feel. It is sectile and flexible and has a specific gravity of 2.1 to 2.3. It is an excellent conductor of heat and electricity and is inert to ordinary chemical reagents. It melts at a temperature of about 3500°C and vaporizes at a temperature of about 4500°C. In the presence of oxygen it oxidizes to CO2 in the temperature range 600° to 700°C, but it is stable at ordinary temperature and markedly resistant to chemical weathering. Although some natural graphite is nearly 100 pct pure carbon, most contains mechanical impurities of various kinds; quartz, biotite, muscovite, pyrite, iron oxides, and feldspars are the most common. Commercial graphite products have a wide range of graphite content, but the better grades contain 80 pct graphite or more. Both natural and manufactured (artificial) graphite are used in industry. Natural graphite products are divided into two broad categories based on grain size. Graphite composed of visible crystals is called "crystalline" graphite, whereas graphite so fine-grained that it is not visibly crystalline is termed "amorphous." The distinction is arbitrary, for all natural graphite is crystalline, and all gradations between the two commercial categories are known. Within the two categories the terminology used in industry is confusing and not entirely consistent. Crystalline graphite comes from two principal types of sources. The first consists of rocks containing disseminated flakes of graphite. This source yields the "flake graphite" of industry. The second comprises vein deposits of graphite, of which those in Ceylon are the most important and furnish the Ceylon graphite of industry. Amorphous graphite comes from any of a variety of sources, including some of those that yield crystalline graphite. Manufactured graphite is made by electric furnace processes, mostly from petroleum coke. Occurrence and Distribution of Graphite Deposits GENERAL Graphite is widely distributed in nature, occurring in igneous, sedimentary, and metamorphic rocks, and even in nickel-iron meteorites. Graphite deposits of economic interest, however, occur mostly in metamorphic terranes. Five principal geologic types of deposits are recognized: 1. Deposits consisting of flake graphite disseminated in metamorphosed siliceous sediments. 2. Deposits consisting of flake graphite disseminated in marbles. 3. Deposits formed by thermal or dynamothermal metamorphism of coal or other highly carbonaceous sediments. 4. Vein deposits of the Ceylon type. 5. Contact metasomatic or hydrothermal deposits in marble. DEPOSITS IN METAMORPHOSED SILICEOUS SEDIMENTS Deposits consisting of flake graphite disseminated in metamorphosed siliceous sedi-

Jan 1, 1960

By Ian Wark

IT has been shown1 that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "stand-ard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,' it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator.

Jan 1, 1939

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.'-4 Samsonov et al.' reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami's Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By Arthur Knapp

The petroleum industry is confronted with the problem of conservalion. This is not a simple problem in view of a wide difference of opinion among authorities as to whether conservation is necessary and the specific direction that it should take. Many writers accuse the petroleum industry of wasting the natural resources of the country. Others link the consuming public with the industry in this waste. Let us define our terms; agree, if possible, on where and when waste occurs in connection with either the recovery or use of petroleum and select such plans for conservation as appear most practical. A plan for conserv3tion which appears to be logical today may not meet the problem tomorrow. The conservation of petroleum is closely linked with the advancement of marly arts and sciences and as these advance, the plan of conservation has to change. The need for conservation does not necessarily rest upon the elimination of waste. There is not necessarily a fixed connection between waste and conservation. Conservation may be necessary or desirable although there is no waste. Definitions Waste: Useless or unnecessary expenditure. Conservation: The preservation of the natural resources for economical use. Both definitions contain adjectives the interpretation of which is extremely difficult. It is the determination of what expenditures are "unnecessary" or what uses are "economical" that will require study and agreement. If one lets his automobile engine run in cold weather in order to keep it hot, it is difficult to measure that necessity. If an automobile is driven two blocks, when the driver is physically capable of walking, what is the measure of necessity. This question is in the realm of one of the oldest of sociological problems, "What is a luxury?"—a problem which has not been solved. The history of society indicates that the measure of a man's wealth has been the measure of necessity. What he can afford to buy without stinting himself in some other direction, is not a luxury to him and, if it fulfills his desires, may be considered his necessity.

Jan 1, 1927

By P. L. Allsman

A method of analyzing blasting action indicates that major cost savings are possible by revising practice and bringing the classical blasting formulas up to date; difficult problems such as taconite and throw-breakup can be attacked by engineering Denonation pressure — the peak pressure developed by the explosive reaction; "shatter blasting." Average detonation pressure — the average pressure over the time the reaction continues; "heave blasting." Radial presswe — the stress in a radially expanding sphere about the detonation. Corresponds to the diminishing peak pressure. Lateral stress - the stress in a circumferential direction, induced by outward movement of the rock away from the detonation. Limiting stress or Slim— the rock property at which failure will occur in the case at hand; may be tensile or compressive strength, or combinations. Recent developments in explosives technology, following the advent of nuclear explosions, have led to a rather complete understanding of their action. A survey was made for the purpose of uncovering any knowledge which might be applicable in the mining and quarrying industries, the principal users of explosives. Although no revolutionary techniques have become apparent, much basic data pertaining to blasting — fortunately not classified — have been developed by recent research, from which a good general understanding of the process can be derived. It is hoped this explanation of the scientific principles governing explosive action, together with a proposed analysis of blasting practice, will further the development of mining engineering. NATURE OF THE REACTION: The phenomenon of explosion, termed detonation, is in reality a rather complex chemical reaction, and as such is completely explainable by physical and chemical laws. Detonation is characterized by high temperature and pressure, extreme rapidity — often being complete within one microsecond — and most importantly by formation of a shock pulse which accompanies the reaction zone. As with any chemical reaction, there is a critical value of temperature and pressure below which detonation can not occur; this is termed the "critical point". Whereas an explosive substance will decompose slowly at ordinary temperature, with the formation of gases which readily dissipate; at elevated temperature the reaction is considerably speeded. If pressure is suddenly applied at some point in an explosive medium, adiabatic compression results, and the temperature is locally raised. When the temperature becomes high enough the decomposition will be so rapid that the gaseous products do not have time to dissipate, but contribute to a further build-up of pressure. This, in turn, furthers adiabatic temperature rise over a widening area, and with any heat generated by an exothermic reaction, causes a rapid increase in temperature. Both temperature and pressure are spontaneously built up in this manner until the critical point is reached, resulting in detonation. The values of pressure and temperature necessary to create detonation are established by the unusual nature of the process. If temperature alone is raised above the critical point, without sufficient increase in pressure, deflagration or "low-order detonation" occurs. In the true, or "high-order detonation", the shock pulse resulting from the violent decomposition becomes an integral part of the reaction, and itself aids in increasing the detonation

Jan 1, 1961

By C. A. Heiland

Measurements of gravity with gravimeters have come into increased use in this country and abroad in the past five years. Probably 100 to 125 gravimeter parties are working in the United States alone. In oil exploration, gravimeter methods have relegated the gravity pendulum definitely to second place, if not third, and now closely rival and possibly surpass the torsion balance in many applications. Gravimeters have lately been applied in mining, although it is doubtful whether they will ever replace electrical or magnetic methods in this work. Notwithstanding the widespread application of gravimeters, there has been no article covering the entire field in the domestic or foreign literature. The purpose of this paper is to meet the demand for comprehensive engineering information on the subject. The working principles of a number of gravimeters will be illustrated and treated in relation to the action of corresponding seismometers and astatization methods. The mathematical discussion of theory has been confined to the most necessary fundamentals and been given in as elementary form as possible. A description of calibration methods constitutes the last part of the paper. The symbols shown at the top of page 197 will be used in equations throughout the paper. Dynamic and Static Gravity Methods Methods of measuring gravity fall into two groups: dynamic and static methods. The first group involves the measurement of time. Examples are: determinations of the period of oscillation of a pendulum, measurements involving the free fall of a body, and comparisons of gravity with the centrifugal force of a rotating body. Measurements in the second group of gravity methods are concerned with deflections of certain indicators when the force of gravity is in equilibrium with another comparison force.

Jan 1, 1940

By C. A. Heiland

Measurements of gravity with gravimeters have come into increased use in this country and abroad in the past five years. Probably 100 to 125 gravimeter parties are working in the United States alone. In oil exploration, gravimeter methods have relegated the gravity pendulum definitely to second place, if not third, and now closely rival and possibly surpass the torsion balance in many applications. Gravimeters have lately been applied in mining, although it is doubtful whether they will ever replace electrical or magnetic methods in this work. Notwithstanding the widespread application of gravimeters, there has been no article covering the entire field in the domestic or foreign literature. The purpose of this paper is to meet the demand for comprehensive engineering information on the subject. The working principles of a number of gravimeters will be illustrated and treated in relation to the action of corresponding seismometers and astatization methods. The mathematical discussion of theory has been confined to the most necessary fundamentals and been given in as elementary form as possible. A description of calibration methods constitutes the last part of the paper. The symbols shown at the top of page 197 will be used in equations throughout the paper. Dynamic and Static Gravity Methods Methods of measuring gravity fall into two groups: dynamic and static methods. The first group involves the measurement of time. Examples are: determinations of the period of oscillation of a pendulum, measurements involving the free fall of a body, and comparisons of gravity with the centrifugal force of a rotating body. Measurements in the second group of gravity methods are concerned with deflections of certain indicators when the force of gravity is in equilibrium with another comparison force.

Jan 1, 1940