Search Documents

By R. E. H. Pomeroy

Early in 1917, it became evident, owing to existing and pending market conditions, that a substitute for crude petroleum must be found for firing the smelter furnaces. After a review of the plants then existing, it was deemed advisable to depart from their practice and to adopt the following described system of distributing pulverized coal to the furnaces. The principal advantages of the proposed system, which influenced this decision, were: (I) Equal safety; no pulverized coal is stored at the furnaces; (2) greater ease of operation, furnace fires being controlled by regulating valves in burner branches, as in gas firing; (3) better organization; all machinery, including pulverized coal feed, is under one roof, and the organization is separate from the furnace department; (4) greater cleanliness; all machinery is under vacuum; (5) greater flexibility of application, the coal and air mixture can be piped where needcd. The design of the plant is the result of the combined efforts of the local engineering staff and of the machinery manufacturers. Many new features were embodied in this design to insure greater safety, cleanliness, and efficiency of handling. After 14 months of continuous operation, the plant has proved entirely satisfactory. The building is of structural steel, covered with corrugated steel, with many windows and is painted light gray inside and out. The building floor is of concrete with ample drains to the sewer, and the building is equipped with fire and service water piping. Fig. 1 shows the east side of the building and the incline conveyor from the raw-coal bins. The plant is operated entirely by electric power. All alternating current is 550 volts, 3-phase, 60 cycles. The pulverized-coal feeding niotors and control mechanism are operated by 220-volt direct current supplied by motor-generator sets in the building. Autamatic push-

Jan 1, 1921

By B. E. Mix

THE present methods of unloading ore and coarse-crushing at the Magna plant of the Utah Copper Co. are the developments of the past five years. Hand dumping and breaking have given way to the rotary car dump and large gyratory; and the bucket elevators and stationary screens have been replaced by conveyors and shaking screens. The coarse-crushing plant may be broadly divided into two units: the primary crushing and the secondary crushing, or primary roll, unit. The former was erected in 1923; with the exception of the excavation, the construction was carried on by forces of the company. Excavation was started in the middle of March, the first concrete was poured July 16, erection of the steel building started Oct. 30, and the unit was com-pleted and operating Dec. 30. The unit has a capacity of over 24,000 tons of ore per day, and cost more than a million dollars. Remodeling of the primary-roll unit extended over a period of years preceding this, some of the work having been done as early as 1918.

Jan 8, 1925

By James T. Kemp

AN historical society of particular interest to mining engineers all over the world was born in Cornwall in 1935. A hundred-year-old winding engine then finished its long labors at the Levant mine on the cliffs near Lands End, England. The engine was to be dismantled and scrapped. A few men living near-by, appreciating that this event was one of the final acts in closing a long century of extraordinary mining and engineering evolution. armed a committee to prevent the destruction of the old mine hoist and succeeded in purchasing the engine. They restored the engine house and in time arranged with the Manor of Trewellard, owners of the land, for a 99-year ground lease on a peppercorn rental.

Jan 1, 1947

By Ernest F. Burchard

A reconnaissance of the chrome and manganesel ore deposits of Cuba was made in the spring of 1918 by Albert Burch, representative of the U. S. Bureau of Mines, and the writer, representing the U. S. Geological Survey. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, size, and availability of the Cuban deposits of the ores of these important steel-alloy metals. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the Island. Mr. George A. Wright, of Baracoa, Cuba, a minirng engineer especially familiar with the chromite deposits of Oriente Province, was a member of the party from Feb. 25 to Mar. 20. It was possible to visit most of the chrome-ore deposits that seemed to be of promise, but there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Furthermore, no attempt was made to examine the extensive chromiferous iron-ore deposits of the Mayari, Moa, and Cubitas districts, as these deposits cannot be regarded as sources of chromium except indirectly. At the close of the field work the essential data concerning the quantity and quality of ore probably available for shipment during 1918 and 1919, in the event of the continuation of the European war, and of the tonnage of ore in reserve, were furnished to such Government bureaus as were interested, including the Shipping Board and the War lndustries Board, and as soon as chemical analyses of the chrome ores could be obtained, a press bulletin on the subject was published by the Geological Survey. In the present paper the engineering data and tonnage estimates contained in the unpublished notes of Mr. Burch have been freely used, and their helpfulness is hereby gratefully acknowledged. Many thanks are due Senor Montoulieu and Mr. Wright for their valuable work in the field; to the officials of the Spanish American Iron Co. and of the various other companies; and to individuals holding chromite claims, for courteously facilitating the work of the party.

Jan 1, 1920

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

By Philip B. Bucky

[CONTENTS t. How Does One Determine WhetherPAGE an ore Body Will Block-cave?R. W. Hughes13 Sherman R. Burdick 13 PAGER. T. Gallagher 14 Mark A. Smith 2 C. F. B. Price, Jr.14 Harry A. Leidich2Benjamin F. Tillson 14 McHenry Mosier2C. F. Jackson14,17 R. W. Hughes2R. Taborelli15 Sherman R. Burdick3Frank A. Ayer16 R. T. Gallagher 3Philip B. Bucky16 Benjamin F. Tillson 3Rollin Farminr6 Lucien Eaton 3J. L. G. Weysser15, 0,17 C. F. Jackson 3George S. Rice17 Philip B. Bucky32. How Does One Determine the Block4. What Determines the Procedure in Dimensions and the DevelopmentRemoving Caved Ore? Work Necessary to Make an OreHarry A. Leidich17 Body Cave?McHenry Mosier17,21 Mark A. Smith 5,7,() R. W. Hughes17 Harry A. Leidich6Sherman R. Burdick 18 McHenry Mosier6,7,12 R. T. Gallagher 18 R. W. Hughes6Mark A. Smith I8 Sherman R. Burdick 7Philip B. Bucky20, 21, 23 R. T. Gallagher 7C. F. B. Price, Jr20 Benjamin F. Tillson 7,11R. H. Bennett21 L. E. Young7C. F. Jackson 21, 23 Robert D. Hoffman8, 1 2Gerald Sherman 3 . 21 Gerald Sherman8Tell Ertl21 Philip B. Bucky10, 11, 12G. K. Foster 23 R. S. McClellan 12C. H. Shoemaker23 Tell Ertl 12 3. How Do the Forces Act and What Are5. What Are the Criteria for Determining the Stresses Developed in a Blockthe Efficiency of a Block-caving That Cause It to Block-cave?Operation? Mark A. Smith 12, ISHarry A. Leidich23 Harry A. Leidich13McHenry Mosier24 McHenry Mosier13R. W. Hughes24 Sherman R. Burdick 24 R. T. Gallagher 24]

Jan 1, 1942

By CHARLES F. DEISS

The total pipe-line runs of petroleum in Indiana during 1945 were 4,114,000 bbl., a decline of nearly 17 per cent below the estimated 4,950,000 bbl. produced in 1944. Drilling activity during the year was centered in Posey and Gibson Counties, where seven new pools were discovered in the state. Four of the pools are in Posey County-Crunk, Farmersville, Jeffries and St. Wendells East-and the other three are in Gibson County-Johnson West, Lysle and Mt. Carmel East.

Jan 1, 1946

By A. B. Kinzel

SILICON, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have devel-oped procedures for the purification of silicon, and Becket&apos;s process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, and the terns "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.1 In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve said further purified by a modification of Tucker&apos;s procedure. This modification differs from Tucker&apos;s method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treat-ment, he does not mention the existence of carbon in the alloy; neverthe-less, lie reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1939

By R. M. Foley, Hidesaburo Kurushima

About 25 pct of all Japanese pyrite comes from the Yanahara mine on Honchu Island. For the past 40 years lack of an economical recovery process forced the operator, Dowa Mining Co., to sell the pyrite for its contained sulfur only, leaving 7 million tons of high grade iron ore waste. Introduction of the Dorrco FluoSolids roasting system enabled the company to make use of its iron sulfides and also to find a market for the mine&apos;s considerable pyrrhotite production. The success of this project is of great importance to Japan&apos;s economy since it points the way toward material increase in her natural resources. Prior to use of the present process, no practical method was available for commercial exploitation of known large tonnages of pyrrhotite, while the copper content of the even larger deposits of pyrite made the roasted residue unacceptable for the iron and steel industry. In Europe, large amounts of copper-bearing pyrite cinder are given a chloridizing roast for separation of the copper and iron but this treatment is not economical in Japan where salt is imported from as far away as Egypt.

Jan 10, 1958

By James P. Savely, Victor L. Kastner

Inspiration Consolidated Copper Company is currently mining in four pit areas; Live Oak, Red Hill, Thornton and Joe Bush Extension, near Globe, Arizona. Small satellite orebodies lying outside the main pits have been mined out in a series of small open pits. Major slope instability has affected production in every pit. Some consequences of the instability have been; (1) Serious interruption of mining plans, which resulted in deferred ore production, lost ore, reduced mining rates and increased stripping requirements. (2) Forced replacement of crushing facilities. (3) Serious effects on other production facilities. The introduction of a slope stability monitoring and control function as an integral part of mine planning has been successful in reducing the impact of these failures and will eventually result in economic pit design based on probabilistic slope analysis. This case history presents a brief review of the problems associated with slope instability at Inspiration&apos;s mines followed by a more detailed report on one specific failure area in the Thornton pit where the use of horizontal drain holes for slope stabilization appears to be successful. Relationships between slope movement rate, rainfall, and mining activity are shown.

Jan 1, 1983

By Virgil R. D. Kirkham

NoRth America has for many years led the world in phosphate production, but with development of African deposits and their marketing conditions with respect to European countries, this leadership will shortly pass to Africa. Algeria, Egypt, Tunis, and Morocco have large phosphate reserves and a correspondingly large production because of easy mining and a ready European market, which was developed during the war. An increase in home consumption is destined to develop for the eastern American fields, and the countries of the Pacific will provide a market for the western producers. New processes indicate a decrease in fertilizer costs, which will encourage a more widespread domestic use and assure better marketing conditions. The African deposits, although benefited by a water haul, have the disadvantage of being isolated from a source of acid so that the crude rock is shipped from Africa to its destination, whereas in the United States the chief product shipped is acidulated rock or various types of superphosphatic fertilizers, The principal types of phosphate deposits used in the manufacture of fertilizers are guanos, apatite, phosphatic marl, phosphatic limestone, phosphatic shale, and phosphate rock which is also known as phosphorite. Some of these deposits are found on each of the continents; Table 1 gives their occurrence, age, location, character, extent, etc. Most of the information found in this table represents a compilation of information published elsewhere in a different form and widely scattered.

Jan 1, 1925

By Alfred H. Bell

The year 1937 has been outstanding in the history of the Illinois oil industry. During the course of the year the state&apos;s daily production has been trebled, increasing from 12,000 bbl. per day at the beginning to 37,000 bbl. per day at the end, and the year&apos;s total, 7,426,000 bbl. is 66 per cent above the previous year&apos;s production of 4,475,000 bbl. The production in January was 368,000 bbl.; in December it was 1,085,000. Production from the old fields increased slightly. Most of the new production is from fields in the central part of the Illinois Basin, an area that for many years was considered unfavorable to the occurrence of oil and gas. The principal producing horizon of the new fields is the McClosky "sand," an oolitic limestone in the Ste. Genevieve formation of lower Mississippian age. Although development has not yet gone far enough to permit accurate estimates of oil reserves in the new fields, it is believed that they are of the order of 100,000,000 barrels. The following are the oil fields discovered in 1937 listed in order of amount of daily production at the end of the year; Noble (Richland County), Clay City, including Southeast Clay City (Clay and Wayne counties), Patoka (Marion County), New Centralia (Clinton County), Olney (Richland County), Cisne (Wayne County),.Beecher City (Fayette County), and Rinard (Wayne County). One gas field, the Russellville, in Lawrence County, was discovered in 1937. For locations of the new fields see Fig. 1. A generalized geologic column for Illinois, showing producing horizons in the new fields, is given in Fig. 2. The total productive area of the new fields at the end of 1937 was 1712 acres, in which 230 wells were producing. Thisrty-five dry holes were drilled within 1/4 mile of producing wells. At the end of the year there were 19 drilling wells, 28 rigs standing, 18 rigging up and 4 new locations in these fields. In the whole state 447 wells were completed, of which 284 were oil producers and three gas producers. Total initial daily production of

Jan 1, 1938

By E. T. Turkdogan, L. J. Martonik, R. J. Fruehan

Electrochemical measuretnents of the solid oxide electrolyte galvanic cells CY-Cr2O3 I ZrO2 (CaO) 1 O (in Fe alloy) CY-Cr2O3 I Tho2 (Y2O3)I O en Fe alloy) have been made at 1600°C (2912°F) in order to test the Performance of such cells at liquid steel temperatures. The oxygen pvobe (cell) consists of a disk of ZrO2 (CaO) or Tho2 (Y2O3) electrolyte fused at one end of a silica tube filled with a mixture of Cr-Cr2O3 which is the reference electrode. Upon immersion in liquid steel, the electromotive force readings achieve a steady value within a few seconds, and remain steady for 30 win or more. The perforwzance of the probes has been tested using Fe-O, Fe-Si-O, Fe-Cr-O, Fe-V-O, and Fe-Al-O alloys; the oxygen contents of liquid steel derived from the measured electromotive forces are in satisfactory agreement with those determined by arulysis. Use of the probe in the deoxi-datiorz of steel, in laboratory experiments, is discussed. The results indicate that there is insignificant electronic conductivity in ZrO2(CuO) at oxygen activities down to those corresponding to 10 ppm in steel. At lower oxygen activities, probes tipped with ThOn (Y2O3) disks perform satisfactorily at oxygen activities down to 1 ppm O or less. THE key to the control of deoxidation of steel is a sensing device to measure rapidly the concentration of oxygen in liquid steel in the furnace, ladle or tun-dish at any desired stage of deoxidation. The analysis of the cast steel by the neutron-activation or vacuum-fusion method gives total oxygen as oxide and silicate inclusions. This analysis is important for guidance to steel cleanliness; however, such a postmortem is of little value in the control of deoxidation of liquid steel. At the General Meeting of the American Iron and Steel Institute in New York, 1968, Turkdogan and Fruehan&apos; presented a paper on the preliminary results of the work done in this laboratory on rapid determination of oxygen in steel by an oxygen probe. Details of the work done in this laboratory leading to the development of a galvanic cell for the determination of oxygen in liquid steel, and the results of the tests made are given in this paper. It was through Wagner&apos;s contributions, since the early Thirties, to the physical chemistry of semiconductors in general that it ultimately became possible to construct galvanic cells for application at high temperatures. In 1957, Kiukkola and wagner2 successfully demonstrated the use of several solid electrolytes in measuring the free energies of several chemical reactions, in particular, the use of lime-stabilized zir-conia in high-temperature oxidation reactions. Starting 7 years later, a number of papers appeared in the technical literature3-&apos; demonstrating possible applicability of galvanic cells for the determination of oxygen in liquid steel. In the earliest work, Japanese investigators3j4 experimented with various types of reference electrodes, e.g., graphite-saturated liquid iron at 1 atm CO or Ni-NiO mixtures; the results obtained, though promising, were not of sufficient accuracy. Except for the work of Baker and West,6 all other investigators5,7,8 showed that ZrO2(CaO) electrolyte could be used for this purpose. The main part of the galvanic cell used by Fischer and ~ckermann&apos; and by schwerdtfeger7 (the latter work was done in this laboratory), consisted of a ZrO2(CaO) tube, -1 cm ID, closed at one end, with a platinum contact wire fixed mechanically inside the closed end. The tube was flushed with a gas of known oxygen partial pressure, e.g., air, CO-CO2 or H2-CO2 mixtures; gas along with the platinum lead wire served as the reference electrode. The oxygen contents derived from measured electromotive forces agreed reasonably well with the oxygen contents determined by vacuum-fusion analysis. It is evident from recent investigations that the electromotive force technique using a solid oxide electrolyte is fundamentally well suited for the determination of oxygen in liquid steel. However, it is equally clear that the cell arrangement of the type as commonly used is in need of considerable improvement, as it exhibits several shortcomings for industrial and even laboratory use. 1) Because of its size, the zirconia tube, though stabilized, has a poor resistance to thermal shock. 2) Fine pores and microcracks, which are invariably present in zirconia tubes, are detrimental to the satisfactory operation of the cell, particularly when gas reference electrodes are used. 3) Air or carbon dioxide reference electrodes give rise to high electromotive force readings; as a result, the determination of oxygen in steel becomes less accurate. For higher accuracy, the oxygen partial pressure of the reference electrode should be in the range similar to that of oxygen in steel. 4) Even in laboratory experiments, difficulties are experienced when flushing the tube with gases and maintaining the proper gas flow rate. Fischer and Ackermann,&apos; who used air as the reference electrode, reported that when the flow rate was too low, furnace gases would leak into the electrolyte tube, therefore lowering the oxygen potential and measured electromotive force. The required flow rate in order to avoid leakage depended on the tightness of the electrolyte tube which varied with different tubes, thus making it difficult to predict in advance the required flow rate. However, if the flow rate is too high the inside wall of the electrolyte tube would be cooler than the wall

Jan 1, 1970

By JAMES J. PURDY

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the under- feed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention.

Jan 1, 1949

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.&apos;&apos; The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.&apos;&apos; The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By FRANK R. VAN

I. INTRODUCTION. IN the summer of 1908, R. B. Cochran, Superintendent of the Compania Metalurgica Mexicana at Sierra Mojada, Mexico, presented to the Department of Geology and Mineralogy at Case School of Applied Science an interesting series of silver-, copper-, and lead-ores from the Veta Rica mine. These ores contained several interesting minerals which were associated in a somewhat peculiar manner, so that I was impelled to make a closer study of their occurrence. The investigation has brought out several new facts concerning the geology of the district and the geological occurrence of the ores, and therefore has seemed worthy of record. Two papers have been published previously about the region, one by Chism1 in 1887, and the other by Malcolmson2 in 1902. These articles, however, treat of the district more from the stand-point of the metallurgist and mining engineer, and not much attention is devoted to its mineralogy and economic geology. II. GEOGRAPHICAL LOCATION OF THE DISTRICT. The Sierra Mojada is situated in the extreme western part of the State of Coahuila, near the Chihuahua boundary. It is reached best via the Mexican Central railroad from El Paso, Tex., to Escalon, Chihuahua, a distance of 494 miles. From this point, a branch line, the Mexican Northern railroad, runs 78 miles in a NE. direction to the mines, which are its northern terminus. The railroad was built about 1890, practically on account of the Sierra Mojada mining-district. 1 Sierra Mojada, Mexico, by Richard E. Chism, Trans., xv., 542 (1886-87). 2 The Sierra Mojada, Coahuila, Mexico, and Its Ore-Deposits, by James W. Malcomson, Tram., xxxii., 100 (1901).

Aug 1, 1912

By Wilhelm Borchers

In all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly-growing number of inventions, inasmuch as the chief constituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity for those elemen&apos;ts which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to heat the refining-slag to the highest point of its chemical activity ; 2, to prevent the iron from entering the slag, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1911

By L. A. Walker

DURING the past twelve years the underground shaft of the United States mine at Bingham has been sunk an additional 2000 ft. with stations and pockets cut every 200 ft. without interrupting the mining of 600 tons of ore per day and the advancing of 1500 ft. of development per month. Following is a brief description of the way the joint work is conducted. The vertical underground shaft is a three-compartment shaft with outside dimensions of 6 ft. 4 in. by 15 ft. 6 in., and inside dimensions for each compartment of 4 ft. 2 in. by 4 ft. 8 in. The manway compartment of the main shaft is used as the hoisting compartment in sinking operations; it is partially lined with 2 by 12-in, lagging and a bucket is used without guides or crosshead. Preparatory work includes the placing of a bulkhead in the manway compartment, 60 ft. above the lowest station or level, the installation of a hoist, a head sheave, a fleet sheave, a-signal system, air and water lines, and a trap door for handling waste.

Jan 1, 1937

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development. The Indian Creek area is in the center of the northern half of Washington County, 11 miles northwest of Potosi, Mo., the county seat. The location is readily accessible from Potosi by car or truck over the all-weather Missouri State Highway No. 114. The topography is one of rolling relief, varying from an elevation of 700 ft above sea level on Mineral Fork and Indian Creek to a maximum of 1176 ft at High Point Tower. It is divided in equal halves between the drainage to Mineral Fork and to Indian Creek. The shaft site at 1060 elevation is on the divide between the two drainage areas. The Indian Creek side is rough and heavily wooded, with only a few cultivated clearings. The slopes to Mineral Fork are more gentle and rounded, with much of the area cleared for farm land. Most of the surface is covered with Potosi and Eminence formations, which show little evidence of any structure. Ore structure was worked out by extensive diamond core drilling, with holes varying in depth from about 700 to 1300 ft. As of Oct. 1, 1950, 218 prospect holes had been drilled within the 36-square mile area. The ore is disseminated galena with considerable accompanying sphalerite in the Bonne Terre forma-tion in the shape of irregular blanket-type deposits. The main controlling structural feature of the outlined mineral zone is a buried pre-Cambrian rhy-olite-porphyry ridge extending partly through the Bonne Terre formation, which laps against the por phyry and also covers it. The mineralized zone parallels and forms an irregular halo around the porphyry ridge and is concentrated in the Bonne Terre formation where the La Motte sandstone is cut out by the porphyry ridge. This is a very common mineral occurrence in the southeastern Missouri lead belt district. The La Motte sandstone, which normally underlies the Bonne Terre formation, is thus cut out entirely. In this area the Bonne Terre is usually about 275 to 320 ft thick, the La Motte varying in thickness from zero up to 400 ft. Commercial concentrations of ore are indicated at several places, the most notable being at the shaft site where an orebody at least 4000 ft long with widths of 500 to 600 ft has been outlined. The total thickness of mineralized rock reaches 150 ft in some holes, although total ore thickness runs from 8 ft to about 60 ft, often in more than one layer. Preliminary Planning Ore reserves as outlined lend themselves to open-stope mining with trackless haulage and mobile loading machines and drilling equipment. This type of equipment has proved to be very efficient during recent years in the company&apos;s lead belt operations. After a study of bids for shaft sinking and an estimation of comparative costs, it was decided that the shaft would be sunk by St. Joseph Lead Co. personnel using company equipment. Since the plant site is about 26 miles from the company&apos;s nearest lead belt operations, it was necessary to plan a complete surface plant, including mill, shops, office, change room, and warehousing facilities. Immediately following the filing of an application for a certificate of necessity, a headframe was selected for which detailed drawings were already available. The order was placed for fabrication so that it could be delivered and erected in time to serve for sinking the shaft. This eliminated the expense of a temporary headframe. Drilling was started on two churn drill holes near shaft location, and two 1000-gpm deep well pumps

Jan 1, 1954