Search Documents

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957

By L. E. Lynd

Ilmenite concentrates prepared from beach and dune sands of Florida, India, Australia, and other localities deviate to varying degrees from the theoretical composition of pure ilmenite, and generally contain more TiO2 than the formula FeTi03 would indicate, and some Fe2O3. This variation in composition is due to different amounts of altered ilmenite in the concentrates. (') The alteration has been shown to take place by oxidation and leaching of the iron in ilmenite, to yield residual products consisting of amaphous or very finely crystalline titanium dioxide and ferric oxide. Other studies(2) have stressed that ilmenite may alter first to an amorphous titanium-iron oxide, or to an amorphous mixture of titanium and iron oxides, with later alteration to crystalline titanium dioxide. There has been some speculation as to whether alteration of ilmenite is usually caused by weathering or by hydrothermal pr0cesses.(3,4,5 Three main methods of approach were used to study the mechanism and rate of ilmenite weathering. (1) Etch tests were used to learn the relationship between crystallographic orientation and the rate of chemical attack on ilmenite. (2) Altered ilmenites in New Jersey sands were compared with ilmenite in rocks of the area from which the sands were probably derived. (3) Experiments were carried out to determine at what rate, and by what agents, originally fresh ilmenite could be altered in the laboratory under simulated weathering conditions. ETCH FIGURES ON ILMENITE CRYSTAL PLANES A rather large ilmenite crystal from Sannidal, Norway, about 11/2 x 11/2 x 2 inches, bearing a few natural faces with imperfect surfaces, was prepared for etching by grinding and polishing crystal planes whose Bravais-Miller indices (referred to hexagonal axes) had been determined by X-ray methods to be 00.1, 10.0, and 10.2. Metallographic examination showed that the crystal was homogeneous, and uniform in orientation, except for the presence of twin lamellae which were oriented with their broadest surfaces parallel to the 00.1 planes of the large crystal. Since ilmenite is rather inert to standard etch reagents, strong solutions of hot sulfuric acid and cold hydrofluoric acid were used. Preliminary tests established that better etch figures were obtained using HF than with H2So4 solutions. The etch figures produced on 00.1 and 01.0 planes of ilmenite by etching 3 to 5 minutes in cold concentrated HF solution are shown in Figures 1, 2, and 3. The figures on 00.1 are "etch hillocks", rather than pits, and according to Honess(6), this phenomenon

Jan 1, 1961

By G. E. Perry, R. D. Seba

The steam soak process is the most widely applied and most successful thermal supplemental recovery process in use today. This process, which consists of injection of steam in various quantities into a well that is subsequently used as a producer, can be repeatedly applied to the same well. The treatment, if successful, will increase the production rate of the well for a given period. For this reason, the steam soak process should be considered primarily as an acceleration method rather than as a method for producing oil that could not be recovered by primary means. However, application of this process to reservoirs containing viscous crude may produce oil that otherwise would have zero present value or would be produced at such low rates by primary methods that it would not be profitable. A major necessity for the successful application of the steam soak process is a source of natural energy. This source of energy may exist in one or more of the following forms: expansion of fluids, compaction, gravity drainage. This study was undertaken to determine the effect of gravity drainage on steam soak production and recovery and to develop a method for predicting production rates, ultimate recovery, and heat requirements when applying this process to a reservoir in which the primary driving mechanism is gravity drainage. (For additional discussion of some of the factors that affect recovery of viscous oils by the steam soak process, see Ref. 5.) Model The model developed for analyzing the performance of the steam soak process in gravity drainage reservoirs is a modified form of that developed by Matthews and Lefkovits.1,2 The model used in this study consists of two concentric cylindrical volumes of productive formation with cap and base rock of impermeable material. The inner cylinder, extending from the radius of the wellbore to some predetermined radius, is referred to as the hot zone; and the outer cylinder extending from the exterior boundary of the hot zone to the outer drainage boundary will be referred to as the partially heated zone. Fig. 1 is a schematic cross-section of the model, indicating its thermal properties. Horizontally the reservoir is divided into two regions, the upper region having a high gas saturation and residual liquid saturation, and the lower region containing a high liquid saturation. The boundary between these two regions is referred to as the free surface, which drops and changes shape as fluid is produced from the reservoir. The model was used to analyze the steam soak process by applying the following assumptions: 1. The horizontal formation is composed of one or more homogeneous noninterconnected layers containing incompressible fluids. Each layer is treated separately. 2. The hot zone is heated by the initial soak and is maintained at the steam temperature corresponding to atmospheric pressure by resoaking. 3. The height of the free surface at the producing well is at all times zero (producing well is pumped off). 4. The position of the free surface at the start of

Jan 1, 1970

By C. C. Miller, A. R. Belyea, C. H. Herty, E. B. Burkart

The removal of sulfur from steel has been studied by many investigators, but the quantitative relationships between the factors involved have not been determined. This is undoubtedly due to the number of variables encountered in practice, an attempt to study any one reaction or relation being affected by other reactions the relative importance of which cannot be estimated. The factors that affect the extent of removal of sulfur in the basic open-hearth process are generally considered to be: 1. Basicity of the slag: (a) Iron oxides in the slag; (b) carbon in the metal or carbide in the slag; (c) temperature. These factors affect the reactions: FeS + CaO = CaS + FeO FeS + CaO + C = CaS + CO + Fe. 2. Amount of sulfur in the gas. 3. Amount of manganese in the metal. The factors which affect the rate of removal of sulfur include, in addition to these: 4. Fluidity of the slag: (a) Normal changes in fluidity with temperature; (b) changes in fluidity because of the addition of special reagents such as fluorspar. 5. Agitation of the bath. Within the past two years, two papers have been presented dealing with the influence of sulfur in the gas on slag and metal. Nead' has shown that if a gas high in sulfur be used for heating, the metal and slag will absorb sulfur. Whitely2 concluded from his experiments that if a

Jan 1, 1925

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the separation efficiency (E,): E. = (R - R,), where R is the percentage of the valuable constituent and R, the percentage of the waste appearing in the concentrate. The separation efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products. The problem of quantitatively assessing the results of a mineral concentration process recurs whenever one tries to decide which of two similar test results is more desirable. Although economic factors may greatly influence the eventual choice of process, they usually have very little to do with the technical excellence of a separation and are, therefore, not a consideration at this point. Concentrate grade and recovery, used simultaneously are the most widely accepted measures of performance, and if both the grade and the recovery are greater for one case than for another, the choice is simple. However, when the results of closely competitive operations are compared, it often occurs that one set of test results shows a higher grade and a lower recovery than another and the choice is no longer obvious. Laboratory investigations of a mineral concentration process applied to a given feed material can often be designed to yield successive paired values of concentrate grade and recovery over the practical range of the course of a separation process.' These results may be plotted as some combination of the cumulative values of grade, weight recovery, or unit recovery in the concentrate. The resulting correlations for two slightly different sets of conditions can then be compared qualitatively, or even quantitatively in particular cases.2 Such comparisons are not applicable, however, to individual concentration test results. The reduction of a separation test result to a single efficiency figure, preferably as a percentage of ideality, would afford the simplest and most precise means for comparing the results of competitive tests. The effective proportion of feed material that undergoes complete separation in any real concentration process, hereafter referred to as "separation efficiency," is such a figure. It is essily calculated from the usual feed and product data and can even be evaluated, in many cases, from data in publications describing various concentration processes. Mineral Concentration Processes and Their Evaluation Mineral Concentration Processes: The overall concentration process may be subdivided into a liberation process which severs the bonds between unlike mineral species, and a separation process, which sorts the resulting liberated particles into two products—a concentrate rich in mineral A and a tailing lean in mineral A. A perfect mineral concentration process is represented by the idealized scheme shown in Fig. 1 in which liberation and separation are not differentiated. The feed mixture consists of two mineral types which are completely liberated early in the process and then sorted by type. All the mineral particles of type A which respond uniquely to the selection forces acting in the ideal separator, report to the concentrate, while all the mineral particles of type non-A report to the tail-

Jan 1, 1971

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 6 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and 6le this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. 11. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the under- signed are all members of said Council as the same was constituted on the 29th day of December, 1904.

Jan 1, 1942

By H. H. Stoek

MINE models have three distinct uses: 1. As exhibits in expositions and museums. 2. As exhibits in law suits. 3. As illustrations in teaching mining engineering. All three uses are in a sense educational. The third, or distinctively teaching function, has not been extensively developed in America as it has been abroad, chiefly because of the cost of the models and the scarcity of model makers. In connection with expositions, such as the Columbian, the Louisiana Purchase, and the Panama-Pacific, a number of very good mine and metallurgical models were prepared with funds furnished by State commissions, by mining organizations or mining companies. At the close of these, expositions, some of these models have been deposited in National or State museums or in educational institutions, but too many of them have been lost, or have been stored, away in some mining company's office or in the basement of some State building, where they have been lost sight of and have gradually fallen to pieces. A visitor to a German mining school is impressed by two facts: 1. The mining laboratories are in general inferior to those in America. 2. The mining museums are infinitely superior -to ours, particularly in models exhibited. One may reply to this comparison by saying that a museum is necessarily a work of time. From the historical standpoint this is, of course, true, but it is not necessarily true in connection with a working museum intended to illustrate current practice. For instance, the oldest mining school in Germany, that at Freiberg, has much excellent historical material, but very little on modern practice, while Berlin, one of the youngest German mining schools, has a most extensive and valuable collection of modern appliances and models. This is true in spite of the fact that one of the best-known model shops is at Freiberg, from which many of, the models to be seen in America have come. Because many of the models in American mining schools have come from

Jan 4, 1917

By H. J. de Haan, J. van Lookeren

In view of their size and favorable characteristics, Shell's heavy-oil fields on the eastern coast of Lake Maracaibo, Venezuela — known as the "Bolivar Coast" — are obvious candidates for the application of thermal recovery methods. During the last decade various methods have been tested, such as steam drive,', steam soak and in-situ combustion.3 Steam soak was discovered as a promising production method rather accidentally in 1969, during early steam drive testing in the Mene Grande Tar Sands1 When steam erupted at the surface due to breakdown of the overburden, the injection wells were back-flowed to relieve the reservoir pressure. This resulted in high oil production rates, all the more impressive because the reservoir is unproducible by primary means. It was concluded that injection of limited amounts of steam might be a very effective method for stimulation of heavy-oil wells. To obtain information that would be more widely applicable, testing of the process was continued in the eastern part of the Tia Juana field (Fig. 1). Here even more favorable results were obtained than in Mene Grande. This created sufficient confidence to prompt a large-scale project, which was considered essential for an adequate evaluation of ultimate recovery, steam requirements, mechanical problems and economic prospects. To obtain an early answer on the ultimate recovery a fairly depleted area was selected in the western part of the same field ("A" in Fig. 1). The first steam was injected in March, 1964. This paper describes the performance until the end of 1966. The production mechanism and well inflow performance are discussed in some detail. In view of the favorable results obtained so far, steam soak operations have expanded considerably since the start of this project. Presently, five other projects are under way, of which two are about the same size as the one under discussion, with further extensions being programmed. Description of the Project Reservoir Data Shell's part of the Main Tia Juana reservoir has a proven area of 8,800 acres and an average net oil sand thickness of 130 ft. It contained an initial quantity of 2,750 million bbl of stock tank oil (STOIIP), with an API gravity ranging from 10 to 15 API and a viscosity of 100 to 10,000 cp (at 122F). As a geological unit it is known locally as the Lower Lagun-illas member of the Lagunillas formation, which is early Miocene in age. The sand bodies are believed to be distributary channel sands deposited in a lower coastal plain. Most of the channel sands have lateral and some vertical communication. The field was developed mainly in the period from 1936 to 1950. The ultimate primary recovery is estimated at 18.1 percent of STOIIP, of which 12.5 percent STOIIP had been produced by the end of 1963 from some 540 wells. By then the average pressure had decreased from an initial value of 960 to 550

Jan 1, 1970

By C. F. Weinaug, R. W. Farley, J. F. Wolfe

A rapid, accurate method for predicting the dew points of gas condensate systems and their subsequent normal and retrograde phase behavior with pressure decline has been developed. The method predicts dewpoint pressure, volume percent liquid, condensate content of produced gas, and the liquid and gas compositions at pressures below the dewpoint pressure. Use of a modified form of the BWR equation of state, which was established by regression calculations on experimental data from several gas condensates, provides depletion behavior predictions that are significantly improved over predictions using K-values based on convergence pressures and Standing's correlation for density. INTRODUCTION Prediction of complex hydrocarbon-mixture thermodynamics is fundamental to reservoir and gas process engineering. In particular, accurate descriptions of phase behavior are needed to plan production operations for gas-condensate reservoirs. Although analysis of reservoir behavior during producing and cycling operations can be made for simple reservoir models, extensions of these studies to more complex reservoir systems are still difficult, both with regard to numerical techniques and the phase behavior of the fluids. This report presents a mathematical method for handling the complex phase relationships encountered in retrograde condensates; it represents an advance in reservoir behavior technology in that it will aid the development of closed-form mathematical representations of total production systems. A typical phase diagram for a complex hydrocarbon mixture is shown in Fig. 1. When the reservoir temperature T, is higher than the critical temperature Tc, and lower than the critical-condensation temperature Tct' the mixture is a gas condensate. Decreasing the pressure on a condensate while maintaining nearly constant temperature will result in two phases forming at the dew point. Further decrease in pressure will cause additional liquids to be formed. This phenomenon is called retrograde condensation. As pressure continues to decrease, normal phase behavior regions are encountered (liquid vaporizes as the pressure decreases) until the low-pressure dew point is encountered. When a gas-condensate reservoir is produced, gas is withdrawn and the volume of fluids in the reservoir remains nearly constant as the pressure declines. Heavier components tend to accumulate in the liquid phase as a result of retrograde condensation, while lighter components tend to concentrate in the vapor phase. Thus, as the gas is produced the composition of the gas and the condensate

Jan 1, 1970

By H. C. H. Darley

The principal causes of unstable boreholes* have been known for many years. For example, in a paper published in 1938, Halbouty and Kaldenbachl listed nearly all the classes of troublesome shales that we know today. Much progress has been made since then, but we still have difficulty in identifying the cause of hole problems and consequently in selecting the right technique for combatting them. This subject was discussed at length by Kelly2 in a recent paper and much valuable information was provided. In the Shell Laboratory it was felt that there was a need for a better understanding of the basic mechanisms underlying the various forms of hole instability, and accordingly, a study was undertaken. This entailed reviewing the physics and chemistry of shales, developing tests for characterizing shales, and constructing a model to study borehole stability. Full simulation of underground conditions was not attempted; for example, we used reconstituted shale specimens, and often simple solutions or suspensions rather than practical drilling muds. Such procedures are necessary in order to establish mechanisms, but caution must be exercised in applying the results to the more complex conditions in the field. Part I — Compaction Swelling and Dispersion of Shales Compaction of Sediments Shales are formed by the compaction of sediments. Water is expressed as sediments are buried by subsequent layers, and the degree of compaction is proportional to the depth of burial, provided the water is able to escape easily to permeable formations. The younger sediments, when recovered at the surface, soften and disperse when mixed with water; the older shales have undergone diagenesis (alteration of the clay minerals, secondary cementation, etc.), and remain hard and unaffected by water. In this paper we shall apply the term "shale", as the drilling engineer does, to everything from clays, which are highly reactive to water, to completely lithified materials such as claystones and slates, which are completely inert. However, because these materials behave quite differently when encountered in the drilling well, it is desirable to develop a simple means of characterizing them. The feature that distinguishes the various shales is their dispersibility in water —soft clays disperse readily, harder shales disperse slowly when agitated, the lithified materials will not disperse at all unless milled. In the dispersibility test used in our study, a weighed amount of dry shale particles in the 12-to-100-mesh-size range was placed in a tube filled with distilled water and allowed to soak for 16 hours. The

Jan 1, 1970

By A. S. Argon, G. East

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By Schumacher, Earle E.

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10" C. in temperature. The precise location of this line is also important in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927

By A. B. Cook, C. J. Walker, G. B. Spencer

Although water will displace oil from a petroleum reservoir to a greater extent than gas will, there are some reservoirs in which gas rather than water should be used for pressure maintenance. This is indicated by the high-percentage oil recovery in the case history reports on the Pickton field1 in East Texas and the Raleigh field2 in Mississippi. In gas cycling, total oil recovery includes vaporized products from the immobile oil in addition to oil produced by displacement. If a large part of the immobile oil is vaporized, total oil recovery may be higher than that obtainable from pressure maintenance by water injection. However, the amount of immobile oil vaporized may range from almost 0 to 100 percent, and no simple and reliable method has been presented in the literature for calculating oil vaporization. Development of such a method was the purpose of this study. Several papers concerning the calculation of oil vaporization have been published,3 6 and each is based on the concept dealing with K values — equilibrium constants for the various components in reservoir oils. (K for a component in a system of vapor and liquid in equilibrium is the mole fraction in the vapor phase divided by the mole fraction in the liquid phase.) This appears to be the most logical approach. Yet, the problem is too great for a perfect solution, even with modem laboratories to analyze oils and high-speed digital computers to perform calculations; the number of components in reservoir oils is too large. Because of their complexity no two reservoir oils are exactly alike. Also, K values change not only with variations in pressure and temperature but also with composition of the reservoir oil. In addition, during gas cycling, the lighter hydrocarbons tend to vaporize first. Thus, the reservoir oil becomes more dense and less volatile as gas cycling continues. Furthermore, the greatest amount of oil vaporization occurs near the injection well. Therefore, a simplified method is required for calculating oil vaporization because a rigorous method is not practical. The present methods of calculating vaporization generally require knowledge of the reservoir oil composition in which the mole fractions of the lighter components through hexanes are given; the remaining oil is described as C, + (heptanes and others of greater molecular weights). Assigning one K value for the C,+ system provides the simplest solution, but this incorrectly assumes that K for C, + does not change as gas cycling continues. This assumption can cause large errors because the K value may become less than a thousandth of the original after a large amount of oil vaporization. Another way to solve the problem is to determine changing K values for C, + according to how much of the C, + has been vaporized. To determine these values a sample of the reservoir oil is injected into a pressure-volume cell, and dry gas is batched in and out of the cell. Appropriate measurements and tests are made to determine K

Jan 1, 1970

By R. G. Fleck, W. R. Webb

Iron ore mining in the Adirondack region of northern New York dates back to the Revolutionary War. It is recorded that Benedict Arnold in his campaigns in the Lake Champlain area during the American Revolution utilized the local ores to produce armament and cannon balls. Through the efforts of early pioneers, the iron mining industry in northern New York gained impetus so that in the 1880's mines in the area accounted for nearly one fourth of the iron ore produced in the United States. Both magnetite and red hematite ores were mined during this period. With the discovery of the Lake Superior ores, the iron ore industry in New York started to decline and remained relatively unimportant until 1938. Modern day methods of mining and beneficiating sufficiently high tonnages of low-grade ores to justify the large expenditures for plant and equipment prompted a resurgence in northern New York mining. During the past several years, the production of iron ore from the Adirondack magnetites has greatly increased, and production which amounted to .6%, of the United States total during the 1918-1928 period (Mining and Metallurgy, November 1943) has been increased to 2.85% of the total in 1948. Today, Republic Steel is mining in the Port Henry-Mineville and Lyon Mountain areas; the

Jan 4, 1950

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By D. F. Hewett

CONTENTS PAGE Introduction 1 Geologic features of eastern Oregon 2 Geology of the Sumpter quadrangle 2 Rocks older than the ore deposits 3 Rocks younger than the ore deposits 8 Lodes of the Sumpter quadrangle 8 Areal distribution 8 Geologic distribution 9 Major features of the veins 9 Mineralogy and texture of the veins 13 Ore deposits zonally disposed around the Bald Mountain batholith . . . . 13 Summary of mineralogy and texture 32 Zonal relations 33 Ore deposits zonally disposed around Greenhorn Mountain batholith . . . 36 Zonal relations 37 Relation of textural features to zonal arrangement of veins 37 Summary of zonal relations 38 Comparison with similar districts 39 Outlook for the district 40 INTRODUCTION IN an earlier report on the Sumpter quadrangle1 it was briefly stated that the quartz lodes of that region might be separated into several groups or belts on the basis of the kind and abundance of the minerals of which they are composed, and that these belts were disposed as areal zones around the principal intrusive mass of the region. When the opportunity to revisit the region was offered in 1929, as a result of a cooperative agreement between the State Mining Board of Oregon and the United States Geological Survey, it seemed advisable to pay particular attention to this feature of the lodes, in the hope that if the idea of zonal relations was confirmed it might serve as a guide in exploitation.

Jan 1, 1931

By L. H. Simons, H. H. Spain

I NT RODUCTION Theory indicates that linear water-floods should exhibit scaling and stabilization properties in both oil-wet and water-wet porous media'. Experimental verification of these proper-ties in oil-wet media was obtained some time ago', and more recently, Perkins', employing a high permeability unconsoli dated sand and a low oil-to-water viscosity ratio, has obtained flooding data in a water-wet medium which follow the pattern of scaling and stabilization. Also, Root and Calhoun3 have found similar trends in the displacement of gas by liquids from unconsolidated sands. In general, however, the experimen-tal evidence appears still somewhat conflicting since scaling and stabilization of water floods in water-wet media has not been observed in most of the studies to date'.".'. The purpose of this paper is to provide a more comprehensive picture of waterflood behavior in water-wet media and to corroborate the validity of the scaling and stabiliza-tion concepts. The need for differentiating between the intrinsic nature of water-oil displacements inside a porous medium and perturbating secondary end effects is discussed, pertinent experimental procedures are outlined and the results of flooding tests conducted at low and at high oil-to-water viscosity ratios on con- solidated, water-wet Alundum cores are analyzed. END EFFECTS IN WATER-WET MEDIA Outlet End Effects The peculiar feature of the outlet end effect in water-wet cores is that it not only results in an excessive wetting phase saturation at the outflow face,'.' but that it also retards the moment of water breakthrough: i.e., causes an undue delay in the appearance of water in the produced effluent. Conditions existing in a water-wet core when water first arrives at the outflow face are schematically shown in Fig. 1. At this flooding stage the saturation distribution, Fig. la, has not yet been distorted by the outlet end effect. A water-invaded pore at the outlet core face, opening into the oil-filled void space between the end of the core and the end plate of the flooding cell, is illustrated in Fig. lb. The curvature of the water-oil interface is concave toward the outlet, and the pressure on the water side of the interface is lower than on the oil side by an amount equal to a certain capillary pressure (Fig. lc). Before the water (of this particular pore) can be produced from the core, it is apparent that the pressure in the water phase must exceed that in the oil outside the core. Accordingly. when water first reaches the outlet face, it will not leave the core but will accumulate inside, and only oil will be produced. Eventually, as the water injection is continued. sufficient pressure is built up in the water to reverse the curvature of the interfaces in the outlet pores, and only then will water be produced from the core. This stage, illustrated in Fig. 2. corresponds to the conventional "water breakthrough" observed in flooding experiments. For purposes of discussion, it is convenient to distinguish between the flooding stage at which water first arrives at the outlet face of a core (Fig. 1) and the stage at which water is first produced from the core ( Fig. 2). The former will be referred to as "water arrival" and the latter water breakthrough. In oil-wet media

By C. E. Gerity

Near Bunker, Mo., in the New Lead Belt, Ozark Lead Co. operates a 6000 tpd lead-zinc mine. Mined ore is transported to the surface in three mechanized and automated steps. The mine is developed by a rectangular-shaped sublevel haulage drift 15 ft high by 28 ft wide, driven on strike below the ore zones. Ore transfer raises were driven from the sublevel at locations near the shaft, 1500 ft distant, and on subsequent 1000 ft centers. These 6 x 5-ft raises are slashed to obtain maximum storage below dump points. These dump points are located on each mining level and are of steel and concrete construction. Spiral 12 X 24-ft inclines driven from the sub-level provide access to these levels for equipment and mine utilities.

Jan 11, 1972

By H. S. Price, J. C. Cavendish, R. S. Varga

A numerical formulation of bigh-order accuracy, based on variational methods, is proposed for the solution of multidimensional diffusion-convection-type equations. Accurate solutions are obtained without the difficulties that standard finite difference approximations present. In addition, tests show that accurate solutions of a one-dimensional problem can be obtained in the neighborhood of a sharp front without the need for a large number of calculations for the entire region of interest. Results using these variational methods are compared with several standard finite difference approximations and with a technique based on the method of characteristics. The variational methods are shown to yield higher accuracies in less computer time. Finally, it is indicated how one can use these attractive features of the variational methods for solving miscible displacement problems in two dimensions. INTRODUCTION The problem of finding suitable numerical approximations for equations describing the transport of heat or mass by diffusion and convection simultaneously has been of interest for some time. Equations of this type, which will be called diffusionconvection equations, arise in describing many diverse physical processes. Of particular interest here is the equation describing the process by which one miscible liquid displaces another liquid in a one-dimensional porous medium. The behavior of such a system is described by the following parabolic partial differential equation:

Jan 1, 1969