Search Documents

By AIME AIME

IN a recent technical paper of the Central Committee of the French Coal Mines (Note technique No. 198, by L. Lahoussay) the author points out that continuous in¬crease in depth of mine shafts makes it more and more necessary to look for appropriate means to reduce the weights and dimensions of the hoisting ropes. Increasing depth demands a larger section and weight for the cable if the useful load is not to be cut down at the same time. This naturally leads to increased cost per ton, and at the same time creates serious mechanical difficulties. The dimensions of the hoisting engine must be increased, acceleration at the start must be decreased so as to avoid periods of excessive peak power loads, and a longer time be allowed to slow down the speed of the hoist when applying brakes. The hoisting rope, upon which depend the dimensions and hence the mass of the hoisting engine, presents the greatest obstacle to the development of hoisting from greater depths. Evidently, for a given depth, the total weight of the rope can be notably reduced by utilizing a wire rope of decreasing section, approaching the theoretical logarithmic form. This is a solution frequently adopted for great depths. Of course, the weight of the rope could be easily' diminished by reducing the useful load, but it is certain that with increasing depth of mining, more effort must be made to confine the hoisting to a small number of shafts, and increase the load hoisted per trip.

Jan 1, 1933

By Mazany, M. S.

THE Caletones copper smelter of the Braden Copper Co. is in the " Teniente" mining district about SO km. (49.7 mi.) southeast of Santiago, Chile. From the seaports of San Antonio and Tralparaiso, the property is reached via the Chilean State Railway (66-in. gage) to Rancagua, whence the Braden railroad (30-in. gage) leads to the smelting plant at Caletones, 60 km. away at 5100 ft. elevation, and continues on to the mine and concentrator at Sewell, at 7000 ft. elevation, 12 km. farther into the Andes. The smelting plant was completed and put into commission in February, 1922. At the start, it smelted daily 750 tons of concentrates produced at Sewell from 10,000 tons of ore; later, its capacity was increased to 900 tons of concentrates from 12,000 tons of ore per day; and it is now being increased to 1100 tons of concentrates from 15,000 tons of ore per day. The smelting plant production is governed chiefly by the

Jan 1, 1925

By J. E. Fox Jr., J. L. Lummus, J. P. Gallus

Fresh water or brine drilling fluids may be kept free of suspended drilled solids by the addition of a water soluble acrylamide-carboxylic acid copolymer at the flowline. Addition of from .01 to 0.2 lblbbl of the polymer solution to drilling fluids containing less than 5 per cent clay solids by weight causes the solids to flocculate and settle rapidly to the bottom of the pits. Solutions of the polymer injected at the pump suction reduce the loss of water to permeable formations without impairing the permeability to oil. The use of drill-itlg fluids clarified with the polymer has resulted in increased drilling rates, extended bit life, and lower drilling fluid costs. INTRODUCTION Field experience and the results of a number of investigations have established that the accumulation of solids in drilling fluid reduces drilling rate.'-' Drilling with water makes possible higher drilling rates than can be achieved with mud but in many areas drilling with water may not be feasible because of the possibility of encountering high formation pressures or by-dratable formations. To combat these conditions, the drilling fluid must possess certain physical properties such as viscosity, density, fluid loss, etc., which require the presence of solids. The current trend in drilling fluid treatment is to maintain as low a percentage of solids as is possible without harmfully affecting the mud properties needed for drilling. Mechanical separating devices such as wet cyclones and decanting-type centrifuges are proving to be an economical means of controlling the percentage of solids and thereby maintaining low solids muds. Also: special muds have been developed for the purpose of retarding the hydration of drilled solids so that they may be more easily removed by shale shakers or settling pits. In some areas, such as West Texas, the characteristics of some formations will permit drilling with water. However, because of the dispersion of drilled solids, it is usually not possible to maintain clear water even with the aid of mechanical separators, or by utilizing large settling pits. For this reason the commonly used term "water drilling" is a misnomer since the water usually contains some solids. Because of the improved drilling rates and other benefits which might be effected, a laboratory and field study was made of the use of flocculating agents for maintaining clear water for drilling. PROCEDURE Laboratory—Solids Settling Two techniques were employed to determine the effectiveness of flocculating agents in settling solids from drilling mud. First, the rate of fall of solids was measured in graduated beakers containing mud treated with various flocculating agents. Natural gum, oil-in-water emulsions prepared with ethoxylated nonyl phenols and diesel oil. and a powdered synthetic acrylamide-carboxylic acid copolymer* (hereinafter referred to as "polymer") were tested as flocculating agents in both fresh water and salt saturated muds containing 4 per cent solids. The polymer was not added in the powder form directly to the muds but was first dissolved in water in a concentration of 3.5 lb/bbl. The polymer solution was then added directly to the mud. The concentration of the flocculating agents, including the polymer, was varied. High rates of fall of the solids indicated high flocculating efficiency. A second technique consisted of measuring the time in minutes required to obtain clear water at the pump suction after addition of the various flocculating agents at the flowline. These tests were made using a model mud circulating system having a total volume of approximately 10 gal. The natural fresh water and brine muds used contained 4 per cent solids. A sketch of the circulating system appears in Fig. 1. The circulating rate

By R. Ingerson

Bore surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. Method and Apparatus In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross-section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 50,000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (I:I6), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1949

By R. Ingerson

Bore surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. Method and Apparatus In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross-section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 50,000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (I:I6), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1949

General Aurelio Blanquet,* the best known of living Mexican soldiers, formerly the trusted friend of Porfirio Diaz and organizer of the old Federal Guard of Mexico City, who as a sergeant commanded the squad that executed sentence on Emperor Maximilian, and. more recently was Minister of War in the Cabinet of Victoriano Huerta, landed in Mexico early in April and joined the forces of Felix Diaz. His landing in the state of Vera Cruz, it was stated, was for the definite purpose of aiding the movement now under way to overthrow Venustiano Carranza and to place in power a government that will be "pro-Ally" in its sympathies and will promulgate and enforce laws that will guarantee the rights of life and property in Mexico. The New York Tinges says of the revolution editorially: "Whatever may be the success of General Aurelio Blanquet's attempt to overthrow the Carranza Government in Mexico, admiration cannot be withheld from the General's publicity manager. No enterprise awning at the overthrow of a Government ever had more favorable and widespread advertising. Felix Diaz, whom Blanquet is going to reinforce, supersede, or overthrow, as the case may be-Mexican precedent in these matters offers opportunity for considerable speculation-has been conducting his revolution, at the old stand for some time, but without much success. But, says General Blanquet's representative, the landing of Blanquet will send a thrill to the heart of every true republican.' Meanwhile a biographical booklet is published, adorned with photo¬graphs illustrating the General's record, including such varied matters as the General in favor, receiving a decoration from Victoriano Huerta, and the General in exile, feeding the birds in Central Park."

Jan 5, 1919

[NORTH AMERICA UNITED STATES ALABAMA AUBURN Sturm & O'Brien, Consult. Engrs. °Sturm, Rolland G. BESSEMER Granger, W. C. BIRMINGHAM Air Reduction Sales Crockett, John M. Amer. Cast Iron Pipe Co. Carter, Sam F., Jr. Donoho, C. K. Anderson Elec. Corp. Davis, Moss V. J. B. Clow & Sons Neptune, Maurice D. Connors Steel Div. °Sandelin, Robert W. Hayes Aircraft Corp. Ricketts, W. E., Jr. Willhelm, A. Clyde, Jr. McWaine Cast Iron King, O. H. Worthington, B. W. Shook & Fletcher Sup. Co. Gearhart, Thomas A. Southern Res. Inst. Dismukes, Edward B., Wheelahan, Edmund J. Thomas Foys Miller, Ralph M. Union Carbide Metals, Co. Brandler, Edgar A. U. S. Pipe & Fdry. Co. Clay, Donald H. Unaffiliated Berg, H. A. Caldwell, H. A. Gilmer, H. U. Harris, Thomas H. Templeton, J. B.]

Jan 1, 1961

By G. W. Tracy, R. D. Carter

Numerical calculations were made to determine the behavior of reservoirs with high-pressure drawdown and wide well spacing where the initial productivity is low and the wells are completed by hydraulic fracturing. The two-phase flow equations were solved for the flow into a single well. This well was assumed to be producing from a reservoir with hydraulically created horizontal fractures (four different systems with fractures were studied). For comparison purposes, additional two-phase flow calculations were made assuming a reservoir with uniform rock properties. The two-phase flow results were also compared with the conventional calculation methods, which do not include the effect of saturation gradients resulting from a simultaneous flow of oil and gas which are normal to this type reservoir. It was found that the conventional methods predict (1) a high and too optimistic value of ultimate recovery, (2) a high producing rate and a high reservoir pressure at a given oil recovery and (3) a low trend of gas-oil ratio with oil recovery. Included in the two-phase flow calculations were provisions to control the oil production rate by an allowable rate and, also, by a gas-oil ratio penalty rule. For the systems with hydraulic fractures, the producing rate was controlled by the gas-oil ratio penalty rule for most of the life. This is in contrast to the system with uniform rock properties which went "on decline" almost immediately. An unexpected characteristic of the systems which included fractures was the early rise in producing gas-oil ratio from 730 cu ft/bbl to approximately 1,200 cu ft/bbl, followed by a "leveling off" before the normally expected gas-oil ratio rise began. Additional features which are a result of hydraulic fracturing are (I) greater ultimate recovery, (2) higher average producing rates and (3) a lower average reservoir pressure at a given oil recovery. INTRODUCTION Some oil fields discovered during the past few years are producing from certain volumetric ally controlled reservoirs (often referred to as solution or internal gas- drive reservoirs) which are characterized by high-pressure drawdown at the wells. Since the available pressure drawdown at a well is limited by the static reservoir pressure and the producing rate is controlled by the available drawdown, wells completed in this type of reservoir usually produce at a rate less than the allowable from the time of completion. Because of this, this type of reservoir is referred to as a low productivity reservoir. Economic considerations require the use of wide well spacing and well stimulation by hydraulic fracturing to make commercial wells in this type of reservoir. Performance predictions for volumetrically controlled reservoirs have been made using a combination of two standard equations. 1. The "Schilthuis" or "Muskat" type material balance equation is used to relate the average reservoir pressure and the cumulative oil recovery. 2. The results from the material balance equation and the productivity factor as described by Pirson' are used to relate the cumulative recovery with producing rate and time. The material balance equation assumed uniform pressure and liquid saturation conditions throughout a reservoir. The steady-state radial flow formula allows for a pressure gradient toward a well but assumes uniform liquid saturation. These calculation methods are adequate for application to reservoirs wherein the drawdown at the well to realize satisfactory producing rates is small compared to the total pressure. In low productivity, volumetrically controlled reservoirs, the pressure drawdown at the well is large cornpared to the total pressure. Although a precise number cannot be given for the magnitude of a large pressure drawdown, values in excess of 1,000 psi would definitely be included. For practical considerations, this usually occurs when the formation flow capacity is less than about 100 md-ft. However, this limit of formation flow capacity will vary with the well producing rate. The low pressure in the neighborhood of the well which results from a high drawdown causes evolution of large volumes of gas. This causes the gas saturation to be higher near the well than at a greater distance—-hence, a non-uniform gas saturation. Also, the relationship between the relative permeability to oil (K/K) and gas saturation is nonlinear but decreases approximately in an exponential way with increases in gas saturation. Because of this, the following chain reaction is established.

Jan 1, 1897

By H. O. Jahns

This paper describes the application of regression analysis for obtaining a two-dimensional areal description of heterogeneous reservoirs from short-term pressure-time data such as that obtained in interference tests. The method replaces the time-consuming trial-and-error procedure commonly used to match field data on an electric analyzer or digital computer with a systematic search which is programmed for a computer. The computer program adjusts the properties of a reservoir model automatically until a least-squares fit is obtained between observed and calculated pressure data. The reservoir is simulated by a single-phase, compressible, two-dimensional model. It is divided into a number of homogeneous blocks whose transmissibility (kh/F) and storage (Fch) values are varied to obtain the least-squares fit. The reliability of these values is determined from their standard deviations and correlation coefficients. Although the method is rigorously applicable to single-phase flow only, multiphase flow can be handled provided saturation changes are small during the test. Possibly the method can also be used to obtain a reservoir description from pressure-production history, but this application is outside the scope of this work. The paper includes, in addition to a description of the numerical procedure, a discussion of some of the problems associated with the method. Rules are given to help in selecting the number of homogeneous blocks and deciding upon their arrangement. The uniqueness of a reservoir description is considered. Finally, the use of the method is illustrated by the interpretation of field data from two interference tests. INTRODUCTION Pressure data from short-term transient tests, such as single-well and interference tests, are widely used to obtain reservoir properties. These tests are usually analyzed by assuming a simple reservoir model; very often, a homogeneous one is used. As a result, analysis of the transient data from each well frequently gives different values for reservoir properties. The problem then arises to combine all these differing results into a more detailed picture of the reservoir. One technique is to simulate the reservoir with a digital computer or with an electrical analyzer and to adjust the reservoir parameters by trial and error until the simulated pressure data are in reasonable agreement with the observed pressure data for all wells. Although this method has been used for both transient tests and pressure-history data, it is time-consuming and subjective. A second technique uses regression analysis to replace the trial-and-error procedure with a systematic search that can be programmed for a digital computer. Use of regression analysis in reservoir description was proposed recently by Jacquard and Jain.1 They divided the reservoir into a number of homogeneous blocks whose properties are varied until a least-squares fit is obtained between observed and calculated pressures. However, they did not consider their technique to be operational, mainly because of ".. .(I) the lack of experience in using the method .. . notably for the improvement of convergence; and (2) limitations imposed by the insufficiency of available computers". 1 While the analysis presented in this paper applies the same general principle used by Jacquard and Jain, the specific method is significantly different. Some differences are (1) the regression problem is solved in a different way which requires less computer time in most cases; (2) a stepwise solution, in which the detail in the reservoir description is increased from step to step, is used to improve convergence; and (3) the reliability of the estimated reservoir .properties.. as measured by their standard deviation and correlation coefficient, is estimated'

Jan 1, 1967

Jan 1, 1924

By J. V. Emmons

It has long been known that the outside skin of tool steel frequently exhibits properties widely different from the interior of the mass.

Jan 1, 1915

By D. L. Harris

Chemical upgrading testwork on Stillwater chomite concentrate shows that reduction roasting and leaching (sulfuric acid and/or ferric sulfate) can provide upgraded feed to ferrochromium furnaces for making upgraded ferrochromium. Two-stage reduction smelting in electric arc furnaces can make upgraded ferrochromium also. Sulfating roasts and leaching (acid and/or water) results using gaseous SO2—SO3 or solid ammonium sulfate were not satisfactory for upgrading chromite. Chemical upgrading of domestic Stillwater (Montana) chromite has been considered at various times1'2' to provide a material with higher chromium to iron ratio, more like foreign high grade ore, for the production of standard grade ferrochromium. Physical bene-ficiation of Stillwater chromite ore can provide a ratio, Cr/Fe, no higher than the ratio in the chromite mineral, which is approximately 1.7. For comparison the analyses of a foreign metallurgical grade chromite ore, a high grade electrostatic process Stillwater concentrate and a stockpile concentrate from the Stillwater ore are noted in Table I. Single stage smelting of the high grade foreign ore with a ratio, Cr/Fe, of 3.37 can provide a ferrochromium of over 65 pct chromium content. Similar smelting of the Stillwater concentrate with a ratio of 1.7 can provide a ferrochromium of 50 to 55 pct chromium content.' It has been demonstrated on a pilot plant scale that chemically upgraded Stillwater chromite having a ratio, Cr/Fe, of 3.0 also can be smelted to provide a ferrochromium containing over 65 pct chromium.5 Two major considerations for an upgrading process are the ratio, Cr/Fe, in the product and the chromium recovery. A minimum ratio, Cr/Fe, of 3.0 is required in the product but for economic reasons a higher ratio is desirable for blending purposes as long as the recovery is satisfactory. Data from different kinds of chemical upgrading testwork are presented in this report. Some of the testwork was conducted to make a product which was not intended to be feed for ferrochrome smelting, but the data are considered pertinent to chemical upgrading. Results reported by others are noted also for comparison. WORK REPORTED BY OTHERS The U. S. Bureau of Mines has contributed much to the literature on chemical upgrading of chromite and a summary is given in Table 11. Reduction roasting and acid leaching were reported by Boericke and Bangert,1 by Lloyd and Gorst, et a1,2 and by Boericke3 to demonstrate very good success on a laboratory scale and only fair success in pilot plant tests for Stillwater (Benbow) concentrates. This work included basic studies on thermodynamic properties to explain the reduction and leaching results. Canadian workers, Downes and Morgan,9 have reported experimental success in upgrading a low grade Bird River chromite, similar to Stillwater material by the same process. Russian workers1' have noted results on reduction tests of high grade chromite which may apply to low grade ores and which help in understanding the reduction process. The use of flux additives in the reduction process was an innovation of their work. The Canadian workers9 also reported other kinds of experiments, including autoclave leaching of the chromite in a limited amount of sulfuric acid. An insoluble basic chromium sulfate was formed and separated from soluble iron, magnesium, and aluminum sulfates to provide an upgraded material. U.S. Bureau of Mines workers, Lloyd, Rosenbzum, Home and Davis,' reported on autoclave leaching of Benbow concentrates as a means of obtaining chromium alum for electrolysis. This last work required selective crystallization of alum to separate iron from chromium. Chloridizing roasting of Benbow and Mouat concentrates has been reported by Hunter and Banning6 and others8 to show that the iron chloride could be volatilized from the chromite to provide upgraded residues.

Jan 1, 1964

By G. W. Jones

THIS paper describes experiments in which eight test samples of gelatin dynamite were fired in three different types of apparatus and the quantity and composition of the gaseous products of detonation determined. The special dynamites were so prepared that the oxygen balance of the samples varied from -35.0 to +6.0 g. per 100 g. of explosive, including the wrapper. By means of this graded series of explosives, the relation between oxygen balance and gaseous products of detonation could be studied explicitly. The effect of varying oxygen balance on explosive strength has been discussed in another paper.1 The apparatus employed in the work described in the present paper included (1) the Bichel gage, a steel bomb of 15-1. volume; (2) the Crawshaw-Jones confined detonation apparatus, a steel cannon from which the explosive is fired into a pipe of 90-1. volume; and (3) the Hercules tank, an apparatus in which the explosive is confined in a quartz block which is placed in a steel tank of about 4500-1. volume. A full description of the apparatus is given later. VARIABLES AFFECTING COMPOSITION OF DETONATION PRODUCTS The character of the detonation products of commercial explosives is governed in part by the same factors that affect the combustion products from explosive mixtures of air with gases or vapors. In either case, combustible materials-namely, carbon, hydrogen, and sometimes sulfur-are present and combined variously. In an exploding gas mixture the combustibles are oxidized by oxygen in the admixed air, whereas with explosives the necessary oxygen is provided by oxygen-carrying materials in the explosive ingredients.

Jan 1, 1928

By David, Cole

THE years 1914-15-16 were a pioneering period in mining, milling, and copper metallurgy generally. It was uncertain just what path the crushing, grinding, and concentrating processes would take. This situation was quite embarrassing to the directors of some of our large porphyry properties, then being equipped for production. Inspiration had already made several designs for its proposed 15,000-ton concentrator, incorporating in them the latest devices developed in the art of gravity concentration, only to have the work vitiated by the rapid march of events. In a little improvised plant, built on ground that is now in the crater of subsidence over the Inspiration- Miami orebodies, flotation was being experimentally ' applied to Inspiration ore by Minerals Separation engineers in 1914, with results indicating that this process would be of major importance in the concentration of the sulfides. How best to apply it, and especially how to crush and grind the ore to the very much finer sizes required for the new process, was a serious question, properly to be answered only by doing it, in full- sized machines, under regular 'operating conditions.

Jan 1, 1931

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972

Jan 1, 1909

By AIME AIME

THE fall meeting at El Paso this year (Oct. 13¬15) will be of unusual interest due to the international atmosphere imparted by the many engineers from Mexico, who are making arrangements to attend this meeting. The meeting will be held jointly with the Western Division of the American Mining Congress. Cooperating in the program will be the representative society of Mexican engineers known as Centro National de Ingenieros of Mexico City, who are plan¬ning on sending many delegates and well known Mexican engineers to the convention. The cooperation of the West Texas Geological Society and the American Association of Petroleum Geologists has also been secured. Brent N. Rickard, manager of the El Paso Smelting Works of the American Smelting & Refining Co. at El Paso, Tex., is general chairman in charge of arrangements. He is receiving splendid cooperation from the Mining Department of the El Paso Chamber of Commerce and from the business people of El Paso, who feel highly honored in having these mining societies meet with them this year.

Jan 1, 1930

By K. V. S. Sastry, V. P. Mehrotra

A laboratory investigation was carried out to study the influence of asphalt, bentonite, and corn starch binders on the pelletization kinetics of coal fines and on the quality of the resulting pellets. Pellet quality was evaluated in term of the compression strength, impact resistance (drop test), abrasion resistance, and resistance to severe weather conditions. The amount of binder addition did not significantly influence the pellet growth kinetics. However, the pellet quality varied markedly depending upon the type and the amount of binder wed. Experimental results are explained on the basis of the mechanism of interaction between the coal particles and the binders. Of the three binders tested, corn starch proved to be the best in all respects but for the resistance to water penetration. Finally, a combination of corn starch (imparting strength) and asphalt emulsion (imparting resistance to water penetration) was found to yield the best quality coal pellets.

Jan 1, 1983

By G. K. Manning, E. R. Stein, E. E. Underwood

Columbium, carbon. and nickel additions were made to iron-base alloys with 20 pct CY. The effects on microstructure, precipitation-hardening characteristics, and High-temperature properties were investigated by means of metallographic, hot-hardness, and magnetic measurements. An austenitic alloy consistilzg of Fe-20Cr-14Ni-0.8C-2.5Cb had higher hot-lzaciness at 1700°F than the other alloys investigated. Its favorable standing is attributed to an enhanced interaction of Cb and Cr4C particles dispersed within a stable austenitic matrix. FOR the past 20 years, cobalt- and nickel-base alloys have been used for the more stringent high-temperature applications because of their excellent creep resistance. Although their performance is quite satisfactory, other base materials must be considered for large tonnage, low-cost applications such as for the automotive gas turbine. Iron-base alloys are also used extensively, but at somewhat lower temperatures, primarily because of the instability of particles or because precipitation occurs at relatively low temperatures. Since unusual stability has been reported for Fe-Cb and Cb-C compounds.1-3 it was hoped that effective amounts of these compounds could be taken into solution at temperatures just below the melting range, then precipitated upon reheating. Actually, strengthening was found to occur by both precipitation hardening in some alloys and by phase transformations in others. Among the alloys investigated, that with the best high-temperature properties owes its strengthening to a combination of carbide particle interaction and a relatively stable austenitic matrix. EXPERIMENTAL PROCEDURES Small preliminary melts of about 100 g were made in a vertical Glotube furnace, using alundum crucibles and an argon atmosphere. Alloys weighing 35 lb were melted in a basic-lined induction furnace, also under argon. The compositions of the alloys are given in Table I. The nickel-free alloys were usually ferritic, while those containing nickel were generally austenitic. Depending upon the particular heat treatments, or the combination of alloying elements, two-phase alloys of ferrite and austenite could be obtained. In the following text, however, the nickel-free or nickel-bearing alloys are referred to simply as either ferritic or austenitic alloys respectively. The small ingots were swaged at 2000°F, in steps, to rods of approximately 3/16-in. diam. The large ingots were forged at 2100°F to 1-in. sq bars. No difficulties were encountered in swaging or forging any of the alloys to as much as 90 pct reduction in area. For heat treating at temperatures above 2000°F, specimens were sealed in quartz tubes under a partial pressure of helium. No special precautions were found to be necessary at lower temperatures. Intermetallic compounds in the preliminary alloys were identified by means of X-ray diffraction measurements. Correlation of these results with micro-structural characteristics (such as color, shape, size, and location) of the compounds aided in their identification. Magnetic susceptibilities were also obtained at room temperature with a Magne Gage instrument after the various heat treatments. To

Jan 1, 1962