Search Documents

By C. O. Lee, R. H. Feierabend, Z. W. Bartlett

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.'.' Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.' Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,-000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the cap-rock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do .not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1953

By S. F. Emmons

Br far the greater number of the members of this Institute are men who are engaged in the strenuous work of the technical part of their profession, and find little time for the abstract scientific work which is less distinctly practical and pecuniarily emunerative. There is, however, a small but increasingly numerous class whose members devote themselves to broad geological problems which underlie the systematic development, and whose work, theoretically, ought to precede and form a basis of that of their more practical brethren. These are the so-called mining or economic geologists, who are, for the most part, connected with State or National geological surveys. From the character of their work, the life of these men necessarily follows rather different line's than that of most of their colleagues, and is not generally familiar to them. It seems admissible, therefore, that to the life of a prominent member of this class, who died during the past year, having literally sacrified his life to his work, a more extended notice should be given than the relatively small number of his contributions to the Transactions might seem to justify. George Romans Eldridge, son of Ellery and Sarah (Mathews) Eldridge, was born on Cape Cod at Yarmouth, Mass., Christmas day, 1854. His boyhood education in the public school at Yarmouth was followed by a six years' course in the Public Latin School at Boston, from which lie entered Harvard Uni¬versity in 1872, being graduated with the highest rank in his class in the natural sciences in 1876. During his college course he spent the summers of 1875-6 at Cumberland Gap, Ky., as volunteer aid to Prof. N. S. Shaler, who was then in charge of the State Geological Survey of Ken¬tucky. This vacation work, undertaken by him rather as a pastime, gave him his first leaning toward geology. Soon

Mar 1, 1906

By M. J. Blackburn

The ordering reaction and its effect on dislocation awangements in alloys based on Mg3Cd has been studied by transmission electron microscopy. Ordering occurs by the growth of ordered domains until they impinge, thus producing an antiphase domain boundary (APB) network. In the disordered alloy, slip is confined to the basal plane while in the ordered condition slip occurs on the basal, prism, and pyramidal planes. Superdislocations have been identuied on these planes and their origin and expected spacings are discussed and compared with the observations. The APBs between the dislocation pairs have been resolved and have proved useful in the identification of superdislocations. Observed slip structures are related to the changes in mechanical properties produced by ordering. At high temperatures magnesium and cadmium form a continuous series of disordered hexagonal solid solutions. At lower temperatures three ordering reactions occur; two based on the compositions Mg3Cd and MgCd3 are transformations to DO19-type superlattices while alloys based on the composition MgCd transform to a B19 lattice. The ordering process in alloys near the composition Mg3Cd has been studied by several workers'-4 and it has been shown to be a first-order type transformation. The variation of mechanical properties with the degree of order and temperature have been reported in some detail by Stoloff and Davies.5 It was shown that the disordered alloy was stronger and less ductile than the ordered alloy, the differences being attributed to changes in the number of active slip planes and to the presence of short-range order in the disordered alloy. In this investigation the ordering reaction has been qualitatively followed by transmission electron microscopy. The effect of this ordering transformation on the dislocation arrangements in deformed specimens has been studied in some detail. EXPERIMENTAL Alloys were melted in a stainless-steel crucible under a flux and chill cast; both melting and casting were performed in an argon atmosphere. The ingots were hot-rolled and tensile specimens cut from the resultant strips. Some large-grained specimens were grown by the strain-anneal method. Heat treatment was carried out in inert atmosphere furnaces and in oil baths at the lower temperatures. Thin foils for transmission electron microscopy were produced by electropolishing in a cooled solution (temp = -40°C) containing 50 cu cm of nitric acid and 180 cu cm of methanol at a potential of 10 v. The ordering reaction was followed by transmission electron microscopy, X-ray, and electrical resistivity measurements but this paper will be concerned chiefly with the electron-microscopy results. Much of the work described in this paper was performed on an alloy containing 26.10 at. pct Cd although two of the micrographs are taken from work on a 25.55 at. pct Cd alloy. RESULTS i) The Quenched Solid Solution. Specimens which were quenched from above the critical temperature showed diffuse superlattice reflections. sark-field analysis on these reflections failed to reveal the presence of ordered domains and thus the superlattice reflections were assumed to arise from regions of short-range order. Quenching from temperatures of 400" to 450°C results in the formation of dislocation loops and helical dislocations. Such defects have been observed and analyzed in detail in several hexagonal metals6-' and as the crystallography and interactions of such loops appear similar in this alloy they will not be reported in detail. Fig. 1 shows a high density of loops

Jan 1, 1968

Granduc lies near the Alaskan border in British Columbia, about 600 miles (960 km) north of Vancouver. Prospecting in the area must take place in the short summer months of fog and rain because the winter is bitter cold, with snowfall up to 960 inches (24.4 m) accompanied by avalanches. Despite these difficulties, the mineral ized area was discovered in the 1920's. By 1956, Newmont Mining Corporation had developed mineable ore reserves estimated at 32,500,000 tons of 1.93% copper. Newmont and ASARCO, in a joint venture, then began development of the ore body, which was partially covered by glaciers. It was apparent a concentrator could not be built at the mine site where overland access was impossible due to the weather conditions and the terrain. Years of engineering studies of all possible access routes finally dictated the driving of an 11 mi long (17.6 km) tunnel passing under three glaciers and three mountain ranges to the nearest feasible concentrator site at Tide Lake. Even then, a mountain road subject to an average snowfall of 800 in. (20. 3 m) had to be built 32 mi (51 krn) from the concentrator through Alaska to Stewart, British Columbia, the nearest port. At Stewart, which is located at the head of a fjord 120 mi (192 krn) from the Pacific Odean, a fully equipped marine terminal was built. The tunnel, the lifeline between mine and mill, was to be driven from both ends; however, in 1965, an avalanche occurred at the Leduc portal, killing 26 crew members and wrecking much of the camp. The tunnel was then driven from one heading adjacent to the concentrator site at Tide Lake, a distance of 53,744 ft (16,381 m) to a point under the ore body. The remote location, type of terrain, and bad weather made supply of crews, equipment, and construction materials difficult; but in spite of these extremely adverse conditions, the tunnel crews set many world records. Mineralization throughout the ore zone is generally uniform in grade and composition and is primarily chalcopyrite and pyrrhotite associated with pyrite. Mining is mainly by sublevel caving. After blasting, rubber-tired load-and-haul equipment moves from level to level by means of an internal connecting ramp system on a 15% slope. At the gathering haulage level, 15-ton bottom-dump cars deliver the ore to a 600-ton pocket equipped with a Hudson "Rock-Flo" dump. The bottom of the ore pocket forms the feed chute to the primary

Jan 1, 1978

By B. B. Gottsberger

IT SEEMS strange that so many years after the pas¬sage of the first acts requiring registration or licensing of engineers, so few members of the mining branch of the profession are aware of what has taken place. Laws regulating the practice of engineering have now been passed in 19 states of this country, and in many others, such legislation has been proposed. That such laws are necessary for the protection of life, health and property, as is stated in most of them, is doubted by many. That the standing of the engineering profession will be improved by them is certainlyy open to question. That such laws are a welcome addition to the regulation of business by governmental agency, is not likely to be a general opinion. That once more, and in spite of appeals to engineers to interest themselves in affairs of government, an active minority has succeeded in imposing its will on a passive majority, seems but too true. However, the laws are there and information regarding them should be of use and interest to those most directly concerned.

Jan 1, 1921

By HOWARND N. EAVENSON

THE year 1930 resembled the preceding one in the coal industry in continuing the era of falling prices and 'of the abandonment of unprofitable mines. Practically all coal prices fell, and in the steam sizes during the last half of the year this was particularly true, due to the small industrial demand. No new mines of any size were opened in the bituminous coal industry, but there was a steady increase in the number of cleaning plants of all kinds built in all fields. It is estimated that at least nine million tons per year were added to the previous total of washed coal. The largest washing plant started during the year was that of the Buckeye Coal Co., at Nemacolin, Pa., with a capacity of 650 tons per hour. Fig. 1 shows - the mixing-bin, conveyor galleries, washing-plant and skip hoist, and Fig. 2 the 120-ft. Dorr thickener for collecting the 48-mesh material from the wash water. Dryers are used for drying the steam coal product. The following statement by J. R. Campbell shows the effect of cleaning on Pittsburgh coal in Greene County: "With the advent of the 650-t.p.h. efficient washing plant in Greene County at the Nemacolin mine of the Buckeye Coal Co., it has undoubtedly been demonstrated that the potential coking-metallurgical coals of the county can be brought within the pale of the highest grade high-volatile coals for steel manufacture. A few months' operation indicates that 9% per cent ash in the raw coal can be easily reduced to under 7 per cent ash in the washed coal and the sulfur from 1.60 per cent in the run of mine to 1.20 per cent sulfur in the washed coal.

Jan 1, 1931

By Walter W. R. May

FOR more than 25 years a few business men who represent virile private enterprise in the Pacific Northwest have been trying to awaken the community to the potential benefits of an open Columbia River. No threat of government com- petition then hung over the industry, which was adjusted to state regulation. Numerous sites were engineered and the findings were laid before the operators of heavy industry in the East, Middle West, and South -even of Europe. These engineering data became, if not the basis, the inspiration upon which the U. S. Army Engineers eventually were to "build the Columbia River Bible" - their great document known as House Document 103, the report on the Columbia River and minor tributaries.

Jan 1, 1940

By Joe B. Alford

Jan 1, 1971

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By F. E. Bash

About three years ago, the writer presented a paper1 on the rate of heating and cooling of a 24-in. round ingot. The present paper deals with work done on larger ingots at the plant of the Allis Chalmers Mfg. Co., Milwaukee, Wis., in August, 1919. Sufficient data on ingots of all sizes were desired to enable one to calculate in advance the rate at which any ingot could be raised to a forging temperature without injury to the steel, determining also the temperature gradient between different sections of the ingot and the length of time necessary to heat to the center. This has now been experimentally determined for 24-in. and 45-in. ignots by the writer and for a 18-in. cube by E. F. Law.2 J. F. Harper has also made tests on heat-treating temperatures on 30-in, ingots; which data are included in this paper. No attempt is made here to work out a formula for the heat penetration of steel, for too many factors are involved concerning which we have not sufficient information, as for instance, the specific heat of steel up to 2300' F. It is hoped that eventually a set of formulas will be developed so that one may calculate maximum allowable temperature differences within an ingot for any particular kind of steel and the rate of absorption of heat and temperature gradient within the ingot for a definite temperature head. EXPEEIMENTAL INGOT The ingot tested was 45 in. in diameter, having been forged into the shape shown in Fig. 1 from 54 in. diameter. Seven -in. holes were

Jan 1, 1923

By R. U. Jackson

FACED with rising costs, the mining industry is looking to new methods and equipment to supply the relief necessary for profitable operation. Conveyor transportation is rapidly taking a superior position to motor tramming in underground mines because of lower installation, maintenance, and operating costs. Haulage is always a critical problem in underground mining. The ease of operation and flexibility of a haulage system can have an important effect on ultimate mining cost. With the average tenor of ores on the downgrade, larger tonnages are required for the same metal recovery. This selection of a tramming system can be the key to a successful, paying plant. Because this shift is being made at an ever advancing rate, it may become necessary to tailor mining operations to the transportation system, rather than to select a haulage system fitting set mining methods. In choosing a haulage system, the relative costs of the various methods are of the greatest importance. Adapting the mine to one or the other type of tramming is not considered in the cost analysis, and very likely would make little difference, outside of location of drifts and raises. In the cost sheet, the problem presents recommendations for a conveyor installation and a comparison of equipment, installation, operation, maintenance, and power costs are made. Under the track haulage estimate, no allowance was made for dumping equipment at the shaft pocket or bin. If this equipment was added to the balance sheet, the additional

Jan 1, 1952

By B. Bernstrom

A 22-ft diam, 7-ft long, wet autogenous grinding mill was installed in the new Cretaceous plant of the Jones & Laughlin Steel Corp. to prepare crude iron ore for concentration in spirals and flotation cells. The paper describes the flowsheet and gives a description of the operating and metallurgical results that have been obtained. These results include capacity, horsepower, operating problems and a comparison of pilot plant results with those obtained in commercial operation. The Cretaceous plant at the Hill Annex mine of the Jones & Laughlin Steel Corp. was designed with a wet autogenous mill for grinding low grade iron ore so that it could be concentrated by spirals and flotation cells. The plant, on the west end of the Minnesota's Mesabi Range, went into operation in June 1961, and preliminary operating and metallurgical information describing the performance of this mill can now be given. The crude is lean ore from the Cretaceous iron foundation. This formation is a beach deposit of Cretaceous age that overlies the Precambrian direct shipping and concentrating ores. This rock in nature is not extremely hard but is quite resilient, resisting blasting in mining and size reduction in milling. It contains hematite as water-rounded particles and other fragments of the underlying iron formation and adjacent rocks cemented together by a high alumina-silica ferruginous matrix. It is interspersed with hard dense hematite agglomerates and also contains granite pebbles and boulders that were not cleaned off during removal of the surface. It has a 3.48 sp gr and in the stockpile the material consists of frag-

Jan 1, 1962

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

By Donald H. Beilstein

The St. Joe Minerals Corporation Lead Smelter and Refinery have been in continuous operation at Herculaneum, Missouri since 1892 as the Herculaneum Lead Smelting Division. Over the years, the plant has undergone many changes to increase production, improve the technology, reduce the cost of operations, and produce the highest grade of primary lead. The latest alterations were begun in 1950 and completed in 1970 and have resulted in the Herculaneum Smelter capacity being increased to in excess of 200,000 tons per year (180,000 metric tons). This increase has made the Herculaneum Smelter the largest in the United States, and second largest in the world. This paper will describe the Herculaneum Smelter equipment, processes, and material balances. Particular emphasis will be given to the McDowell-Wellman 10' x 100' (3 x 30 meter) up-draft sinter machine and ancillaries; to the new Heavy Smelting Department (blast furnaces and drossing section); to the new Lead Refinery and its automatic casting equipment and to the gas handling system including the 340 tons per day (305 metric) Sulfuric Acid Plant utilizing a -four pass converter. The description will include photographs, flow sheets, tonnages and assays where applicable.

Jan 1, 1970

By Oscar E. Harder

THE TERM "physical metallurgy' is used in the title of this lecture in preference to "metallography ?because the former has a broader meaning with most audiences, some people thinking of the latter as being limited to work with the microscope. This distinction, how- ever, has not been held by the out- standing workers in the field of metallography, such as the late Professor Sauveur. In the broadest sense metallography is essentially the same as physical metallurgy. The American Society for Testing Materials has adopted-the following definition: "Metallography is that branch of science which relates to the constitution and structure, and their relation to the properties of metals and alloys." This definition might be improved by adding after "properties" -"and their industrial and scientific uses." Metallography has also been defined as the science of metals and alloys. Physical metallurgy is to be distinguished from process metallurgy in that the latter relates particularly to the production of metals from the ores.

Jan 1, 1940

By Samuel D. Warriner

(Wilkes-Barre Meeting, June, 1911.) THE dealings between concentrated capital invested in the conduct of our various industries and the combinations of labor known as "trade union organizations," have produced not only in the United States, but abroad, many novel methods of negotiation between employers and wage-workers. The size and strength of these organizations have destroyed the personal elements formerly governing the dealings between employer and employee and have produced various forms of trade-agreements now in more or less successful operation. The difficulty, however, has- been to secure consent of both parties to an equitable agreement. For this purpose there have been devised various forms of arbitration, either compulsory under the shadow of governmental legislation, or voluntary by mutual agreement. But these have not been altogether successful from a technical stand-point, for the reason that a compromise has generally been necessary, and in an effort to reach an agreement, terms have been made which have been neither fair nor satisfactory to either of the contending parties. The Anthracite Board of Conciliation represents one of the few thoroughly successful courts for the settlement of trade-disputes, if not the only one which has yet been evolved. The prestige of this board rests upon its successful treatment of the labor-troubles of the anthracite region for a period of more than eight years, and upon the fact that it has been able not only to reach decisions based upon the merits of the controversies, but to enforce its decisions upon both the employees and the employers. It has never been obliged to shape its conduct to secure the consent of the contending parties, and its decisions have been strictly and, in the main, cheerfully observed. The remarkable feature of this board has been that it has

Aug 1, 1911

By Donald B. Gillies

PROBABLY the most critical and difficult period in an engineer's career is that between the completion of his college work and his attainment of professional recognition and accepted status in the industrial world. Upon leaving school the young graduate breaks his immediate ties with his educational institution and in a sense finds himself adrift. At this time in his life a society like our Institute has both the responsibility and the privilege of meeting a vitally important need in his professional life. Some of these young men are Student Associates, in the year after graduation, and some are Junior Members, but all need advice and assistance. In some respects this situation will be accentuated by the war. Not only will thousands of young engineers be mustered out of military service but the process we describe generally as industrial reconversion will make necessary many readjustments in personnel. About two years ago the Institute recognized the opportunity of helping the younger member to help himself by appointing a new standing committee to be known as the Committee on Professional Development of Junior Engineers. Herbert Hoover is Honorary Chairman and it is my privilege to serve as Chairman. The name of the Committee is not entirely satisfactory but it expresses the general objective. The present article is in the nature of a progress report of the work of this Committee.

Jan 1, 1945

By C. S. Barrett, D. F. Clifton

THE transformation that occurs in lithium and its solid solutions containing magnesium1,2 is similar in many respects to other diffusionless transformations of the martensitic type. This general similarity makes it desirable to investigate the transformation curves in detail. The current interest in the phenomenon of stabilization in martensitic transformations has created a need for a careful appraisal of possible stabilization effects in both cooling and heating transformations in lithium alloys. The effect of prior heat treatment on the temperature at which transformation begins and the effect of various temperature cycles in partially transformed alloys also merit attention. Limited data on some of these features were presented previously,' but the present studies have been made with improved apparatus, in which erratic fluctuations were smaller than in the earlier work, and include many independent determinations of certain critical observations. Material and Methods Geiger counter X-ray spectrometers were used: a Norelco instrument, original model, and a General Electric XRD-3. The low-temperature specimen holder has been described elsewhere." Specimens 10 mm in diam and 1.5 mm thick were held in firm contact with a copper block which was attached to the lower end of a stainless steel tube that extended up to a reservoir of liquid nitrogen. A heating coil on the tube permitted a controlled temperature gradient along the tube, so that desired temperatures and rates of heating and cooling could be obtained by controlling the heating current. The specimen was surrounded by an atmosphere of evaporated nitrogen in an insulated chamber having double cellophane windows. The temperature of the specimen was read by a thermocouple imbedded in it close to the irradiated area; the specimen could be held at constant temperature within 1°C for long periods. The body-centered cubic 200 reflection near 8 = 26" was used as the index of the amount of b.c.c. material present; occasional checks were made using the most suitable line of the low-temperature phase, the close-packed hexagonal 110 line near 8 = 29". Copper radiation was used throughout. A continuous record was made of the reflected intensities on a strip chart recorder, both when the peak intensity of a line was being followed and when the lines were being scanned at constant temperature. On the continuous recordings of peak intensity, periodic checks were made on the background intensity between the lines, and on the setting of the spectrometer for maximum intensity. The lithium-base solid solution containing 12.4 atomic pct Mg (33.3 wt pct) that had been used previously' was chosen, as it had a transformation range at relatively high temperatures, so as to permit wide temperature cycling within the range. Just prior to use a pellet was cut from the ingot,

Jan 1, 1951

By J. L. Brimhall, R. A. Huggins, M. J. Klein

IN a recent paper1 it was shown that small additions of magnesium, copper, and oxygen decrease the stacking fault probability in plastically deformed silver. Correlation of :X-ray data with measurements of the twinning frequency and metallographic observation of slip lines indicated that this effect may be due to an increase in the relative stacking fault energy. It is the purpose of the present note to report experiments on these alloys of known stacking fault probability that relate to the stacking fault contribution to electron scattering in silver. There has been a considerable amount of disagreement in the literature concerning the contribution of dislocations to electrical resistivity in metals. Calculations relating to the scattering of conduction electrons by the dislocation core, its strain fields, and related effects have been made by several authors.2-5 In addition, experimental work on Cu,3,6-10 Ni,11 and Ni-Co alloys1:! has shown that dislocations in those materials exert an anomalously large effect on resistivity, this effect being related to the presence of extended dislocations. The problem of the scattering due to the stacking fault region between partial dislocations has been treated theoretically using several different procedures.13-'0 The results of these calculations show a wide range of predicted values, from rather large to completely negligible, due to the models and the approximations involved. Almost all of this work has been applied to the specific problem of scattering in copper. The more complete theoretical treatments depend rather critically. on the shape of the Fermi surfaces and the effective mass parameters. The scattering from stacking faults might therefore be expected to vary significantly from one metal to another. Unfortunately, sufficiently accurate information is not available .which would allow one to have any confidence in a theoretical prediction of the scattering in the case of silver. Resistivity measurements were made on small wire specimens of vacuum melted high purity silver and several dilute alloys. These measurements were made at approximately 20°C, with great care being given to temperature measurement and corrections. At such temperatures phonon scattering is significantly greater than imperfection scattering. However, the experimental technique was such that measurements on similarly treated samples were reproducible to better than 2.4 X 10-9 ohm-cm, which was satisfactory for this work. Values of the stacking fault probability and the increase in resistivity after severe plastic deformation are given in Table I. The increases in resistivity resulting from plastic deformation agree quite well with previous work on silver.14,21-26 In addition, it has been previously found that interetitials and vacancies in silver anneal out well below room temperature, so that the residual imperfection scattering in these experiments could be expected to be primarily associated with dislocations;. It is seen from the data in Table I that large changes in stacking fault probability are accompanied by differences in resistivity due to imperfection scattering of only a few percent. If the scattering of conduction electrons by extended dislocations is primarily due to the area of the stacking fault region independent of the stacking fault energy, and not the core and strain fields associated with partial dislocations, the resistivity increase should be proportional to the product of the dislocation density and the stacking fault width, as is the stacking fault probability. Therefore, the imperfection scattering caused by plastic deformation of the alloys should be considerably smaller than that found in the pure silver. Since this was not observed, these results sugegest the possibility that stacking faults do not themselves contribute appreciably to the electrical resistivity of silver deformed at room temperature. An alternative explanation of these observations is that the scattering by the stacking fault is roughly proportional to the stacking fault energy, rather than being determined by the total area of such faults. Sufficient evidence is not yet available to separate these two possibilities. This work was supported by the Office of Naval Research.

Jan 1, 1962