Search Documents

By Raúl Daniel López

Ternium-Siderar steelmaking has been focused in permanent improvements and process optimization. At present the Slab Continuous Caster N°1 has been totally transformed after 20 years of uninterrupted work. The authors of this paper summarize and comment on aspects which were the main changes and place emphasis largely on those technological developments in which they have been active during that period. Productivity and quality have been our goals during the last 20 years; it has led us to improve process and to achieve better control tools. In the development of this presentation, the authors will put special emphasis on the explanation of those works that were made following their own experiences through the technical personnel who belong to the staff of the company.

Jul 30, 2018

By Fernando Velazquez Guzman

Titanium is an alloying element used to refine grain size in steel and improve its physical and mechanical properties. In some stainless steels it is used to increase the resistance to corrosion by the precipitation of titanium carbides or carbonitrides. Its alloying performance is highly variable and depends largely on the stage of the secondary metallurgy process when it is added. Furthermore, the addition method (wire injection or direct addition) has a remarkable influence in secondary refining. This paper describes the tests performed in vacuum degasser (VD), with a highly compacted and encapsulated Ferrotitanium wire (FeTi HC). The yield of titanium in steel increased from 52% to 89%. Moreover, the consumption of the highly compacted Ferrotitanium was optimized.

Oct 30, 2017

By Priscilla Pessin Coppo

The prevention of dental enamel wear has particular relevance for preventive and restorative purposes in dentistry. The wear damage can increase due to salivary disorders and/or parafunction (bruxism); antagonists incisal surfaces become flat and coincident. This study aims to investigate the wear behavior and the related mechanisms in sliding pairs of conformal incisal enamel, with similar values of hardness and fracture toughness, with different applied normal loads and lubricated conditions. Bovine incisors, under pin on flat configuration, were tested in two lubrication condition (dry or with natural saliva) and two applied normal loads (8 and 16 N). The worn surfaces were investigated by 3D profilometry and SEM. The analysis of worn surfaces indicated mechanisms of brittle fracture, but with different severities. Under a normal load of 16 N and dry condition, wear is controlled by a brittle process: microcracking with flake-like wear particles, which results in high friction coefficient (> 0.85), wear rate and wear volume. On the other hand, under a normal load of 8 N and natural saliva, wear took place in the interprismatic region, with consequent exposure of prisms and fracture in localized regions. In this case, the friction coefficient was 16% lower and the wear volume was one order of magnitude lower. Under 8 N and natural saliva, the wear was greater than in the dry condition, probably due to tribochemical reactions.

Jul 31, 2018

By Valdeci Paula Alvarenga

Foi desenvolvida uma mistura briquetada utilizando escória recirculada, gerada no convertedor MRP-L e finos de fluorita para substituir a fluorita granulada no refino primário do aço SAE1012 na Aperam. A utilização desse briquete permitiu a substituição parcial da fluorita granulada, importada, sem prejudicar as reações de descarburação e desfosforação, mantendo as mesmas condições físico-químicas da escória. A qualidade interna dos aços produzidos, usando este novo insumo, permaneceu inalterada, atendendo a todas as exigências especificadas para os produtos.

Jul 30, 2018

By Sébastien Gérardin

Developed for more than 30 years, continuously improved, cored wire is nowadays a reliable solution for the improvement of sustainability, safety, health and doing quality and cost saving. Cored wire allows the addition of ferroalloys and treatment of liquid steel, especially concerning the calcium treatment. Amongst all the processes in secondary metallurgy, calcium treatment is certainly the most critical one before casting. Besides the traditional CaSi and CaFe wires, new types of wire have been designed for becoming the new reference in calcium treatment. PapCal (calcium insulated wire) and HDx (high density calcium wire) are a very versatile range of products. Indeed, according to the steelmaking process parameters (steel grade, treatment temperature, ladle size, calcium content targeted in tundish and even injection conditions), their technical specifications may be adapted in order to optimize the calcium treatment as high as possible.

Aug 16, 2017

By Davide Onesti

Electrode regulation is the technology at the heart of the AC and DC Electric Arc Furnace. As such, in the last decade it underwent continuous improvement to maximize the EAF performances, in terms of process efficiency, machine utilization and operator safety. Given this background, Danieli Automation’s efforts in the field of electrode regulation have been focused on fast response to scrap cave-in, compensation of supply variations, automatic resonance detection, transformer protection, dynamic regulation of the electrical and chemical set-points, coordination and control of slagging and foaming agents, arc irradiance supervision. An extensive analysis of operator utilization and feedback was also carried out to develop an innovative system HMI. In this field, the choice of the variables shown to the user is the key aspect to allow a prompt process evaluation by the operator, who can refer to a condensed set of useful data. This paper will describe the innovative features and embedded models of the electrode regulation module (Q-REG+) and the supervision HMI, together with the effects of their application on EAF process efficiency and system usability.

Oct 30, 2017

By Lívia Maria Sant’Ana do Prado

Neste trabalho foi avaliado um método alternativo de redução dos óxidos de cobre, a técnica de redução assistida por plasma de hidrogênio em reator de plasma pulsado de corrente continua (cc). O plasma de hidrogênio apresenta como possibilidade a produção de espécies de alto poder redutor, derivadas da molécula de H2 [1], além de produzir majoritariamente, como produto da reação, o vapor de água que não é prejudicial ao meio ambiente [2]. A pesquisa se limita ao estudo da influência da pressão do processo de redução a plasma sobre a redução de pós de óxido de cobre (I) (Cu2O). Os experimentos de redução foram realizados em um reator a plasma pulsado DC, sob fluxos de hidrogênio de 300cm3/min, temperatura de 300°C, tempo de 60 minutos e pressões variáveis de 267, 534, 800 e 1068 Pa. Determinou-se a eficiência da redução através de um balanço de massa e foram feitas as seguintes análises nos produtos da redução: difração de raios-X, microscopia eletrônica de varredura e EDS. Os maiores valores de frações de redução foram obtidos a 800Pa, o que pode estar associado à formação de uma bainha catódica que envolve por completo e de maneira uniforme a superfície das camadas de pó.

Aug 8, 2018

By Rodrigo Rocha de Meira

O laminador de tiras a frio n° 3 da CSN apresentava perdas de produtividade ao processar aços de elevada resistência microligados, com limite de escoamento mínimo igual a 340 MPa, dotados de largura superiores a 1400 mm. Devido à crescente demanda do mercado automotivo relativa a esta família de aços, tornou-se necessário um estudo para optimizar a produtividade do equipamento e não desestabilizar o fornecimento aos clientes. O estudo consistiu em testar parâmetros de processo alternativos, objetivando abastecer o laminador de tiras a frio com bobinas laminadas a quente dotadas de resistência mecânica ligeiramente menor, para promover maior estabilidade operacional no equipamento a partir da redução das cargas de laminação. As alterações propostas resultaram no aumento de produtividade do laminador de tiras a frio, sem comprometer as características mecânicas do produto final.

Jul 30, 2018

By Carlos Gonzalez-Rivera

An alternative cooling curve analysis method focused on the experimental determination of the latent heat of phase changes and phase transformation kinetics is proposed in this work. The method analyses the cooling process of a metallic sample, initially liquid that is contained into a cylindrical metallic mold, both of known weight, thermally isolated at its top and bottom. The method is based on an energy balance associated with the experimental measurement of the temperature change of the sample and the mold during their cooling process. From the numerical processing of the cooling curves, are obtained approximate values of the acting global heat transfer coefficient as a function of temperature in order to describe quantitatively the energy exchange of the metal/mold system with its surroundings. These relationships and other experimental data are used to process the cooling curve of the sample and the mold during solidification, in order to obtain the latent heat of solidification.The method was applied experimentally to zinc and tin of commercial purity, initially liquids and contained into stainless steel molds in order to determine its ability to measure the latent heat of solidification. The obtained results suggests that this method shows a good potential to characterize the solidification of metals.

Oct 30, 2017

By Humberto Tronconi Coelho

The use of friction dampers are wide proposed for a variety of mechanical systems for which it is not possible to apply viscoelastic materials, fluid based dampers or others viscous dampers. An important example is the application of friction dampers in aircraft engines to reduce the blades vibration amplitudes. In most cases, friction dampers have been studied in a passive way, however, a significant improvement can be achieved by controlling the normal force in the contact region. The aim of this paper is to study four control strategies for friction dampers based on three different hysteresis cycles. The first control strategy maximizes the energy removal in each harmonic oscillation cycle, by calculating the optimum normal force based on the last displacement peak. The second control strategy combines the first one with the maximum energy removal strategy used in the smart spring devices. Finally, is presented the strategy which homogenously modulates the friction force. Numerical studies were performed with these four strategies defining the performance metrics. The best control strategy was applied experimentally. The experimental test rig was fully identified and its parameters were used for numerical simulations. The obtained results have shown the good performance for the friction damper and selected strategy, also, the agreement between numerical and experimental results.

Jul 31, 2018

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Victor Freire de Oliveira

Em 24 de julho de 2014 entrou em operação o alto-forno 2 da VSB, projeto de fornecimento Paul Wurth cuja conclusão de montagem foi em 2011. O alto-forno, primeiro montado de um total de dois fornecidos, foi desenvolvido para conferir à VSB a maior flexibilidade operacional possível sendo capaz, inclusive, de operar com coque ou carvão vegetal, alternadamente. A instrumentação e automação são modernas e avançadas, oferecendo à VSB amplo controle sobre o processo. A presente contribuição técnica visa apresentar as características que tornam o altoforno 2 da VSB um reator especial e o mais moderno em sua categoria.

Aug 16, 2017

By Levi de Oliveira Bueno

Constant stress testing was used for characterization of creep behavior of a 1Cr0.5Mo steel plate in the ex-service condition. The tests were performed on creep machines equipped with Andrade-Chalmers type profiles, high sensitivity SLVC transducer extensometry, high stability temperature controllers, and facilities for monitoring the creep curves with an automatic data logging system. Ten creep machines of this type were used in this research, in an experimental work that lasted for one year. Three temperature levels were selected: 538, 565 and 593°C, with stress in the range from 52 to 224 MPa producing rupture times varying from 5 to about 3950h. The creep curves were all followed with great scrutiny using data logger scanning rates which enabled storing thousands of readings in each case. The experimental analysis involved measurements of minimum creep rate, rupture time and final elongation at rupture. The data were analyzed according to the classical phenomenological / physical relations (Norton, Arrhenius, Zenner-Hollomon, Monkman-Grant) and also considering five traditional parameterization methodologies (Larson-Miller, Orr-Sherby-Dorn, Goldhoff-Sherby, Manson- Haferd and Manson-Succop). Comparisons are presented among the possibilities of data extrapolation from five different methodologies. Comparison is also made with creep results obtained on a similar plate of the same material in the virgin condition.

Aug 16, 2017

By Luana De Lucca de Costa

O forjamento a quente em matriz aberta é, atualmente, o processo mais utilizado para a fabricação de peças de grande porte. Neste estudo, a simulação numérica foi utilizada, através do método de elementos finitos, para análise do processo de forjamento em matriz aberta de um eixo vazado e escalonado aplicável em aerogeradores. A partir de um billet cilíndrico vazado de aço AISI 4140, pesando 1 kg, é simulado o processo de forjamento objetivando a obtenção de geometria final apresentada. Utiliza-se matrizes superior e inferior em formato côncavo, e um mandril de manipulação com inclinação de 1,15°. A cinemática da simulação numérica, que inclui 4 passes com um número total de 30 cursos, é avaliada. Ao comparar a geometria apresentada com a obtida observa-se que o alongamento longitudinal da forma final é obtido. A partir da análise da temperatura, pode-se concluir que o reaquecimento deve ser realizado após cerca de 45 s, no final de cada série de 5 cursos.

Aug 8, 2018

By Yukio Shigaki

Tendo como objetivo a melhoria contínua dos processos de laminação de produtos planos, foi elaborado um projeto de aplicação de modelos matemático-numéricos para a simulação dos laminadores de tiras a frio da Companhia Siderúrgica Nacional (CSN). A premissa principal é a de que esses modelos permitirão relacionar as diversas variáveis operacionais com o perfil emergente da tira e, baseado na variação da coroa entre a entrada e a saída, estimar a qualidade da sua planicidade. O presente trabalho apresenta os principais modelos aplicados, informações sobre os ensaios realizados para tomada dos dados industriais e alguns dos primeiros resultados com foco no perfil e planicidade. Resultados preliminares indicaram a modificação da coroa dos cilindros de trabalho do Laminador de Encruamento, levando à redução da quantidade de tiras com ondulado lateral. Também foram obtidos resultados satisfatórios na simulação das cadeiras do Laminador de Tiras a Frio no. 1, que é composto de cadeiras 6-high e 4-high.

Oct 30, 2017

By Paulo César Lemes de Almeida

O Alto-forno 2 da VSB, na Usina de Jeceaba – MG, Brasil possui volume útil de 350m3. Entrou em operação em 24 de julho de 2014. Utiliza 100% de carvão vegetal como carga redutora. Nesta contribuição técnica é apresentado o planejamento para o início de operação, destacando-se o enchimento do alto-forno, a distribuição de carga e a preparação da área de corrida. São mostrados os resultados alcançados no primeiro mês de operação.

Aug 16, 2017

By José Artur Albano de Guimarães

A temperatura de carregamento do ferro-gusa no convertedor é de suma importância para o acerto do balanço térmico do convertedor. Dessa maneira, o presente trabalho teve como objetivo a proposição de uma equação de modelamento da perda térmica na panela de ferro-gusa da thyssenkrupp CSA com o intuito de prever, com melhor acurácia, a temperatura de carregamento no convertedor. Os resultados encontrados pelo modelo foram comparados com os valores reais de perda térmica na panela e concluiu-se que a equação desenvolvida se mostrou bastante assertiva e abrangente. Foram consideradas novas variáveis nesta abordagem que, até então, não eram utilizadas pelo modelo de perda térmica nas panelas de ferro-gusa da CSA.

Oct 30, 2017

By Ricardo Wilson Nastari Denigres Filho

Durante estudos de síntese hidrotérmica (realizada em presença de ácido acético e em autoclave à temperatura de 160oC) com o propósito de obter-se boemita a partir de uma gibsita comercial, observou-se uma morfologia diferenciada nos cristais de boemita obtidos: os mesmos apresentaram-se na forma de placas finas de perfil pseudohexagonal. No entanto, quando a síntese é conduzida nas mesmas condições de temperatura somente em água destilada, a morfologia da boemita formada é a de cristais cúbicos. No intuito de tentar entender o mecanismo do crescimento dos cristais de boemita na presença de íons acetato, foram realizadas novas sínteses, envolvendo o mesmo procedimento de preparação, porém variando os meios nos quais a reação ocorre. A partir de novas sínteses realizadas com acetato de potássio em meio aquoso neutro (pH=7) ou ácido (pH=2), foi observado que a presença do íon acetato no meio reacional é determinante para a obtenção da morfologia lamelar. A estrutura cristalina dos cristais obtidos foi caracterizada por DRX e a sua morfologia foi examinada por MEV.

Aug 8, 2018

By Rodrigo Fina Ferreira, Jacek Kolacz, Luciana Gois, Neymayer Pereira Lima

The recent developments on the sensor detectors together with the higher capacity of the machines, due the high-speed computing recent advances, have made possible extending the application in the mining industry. The use of x-ray fluorescence, x-ray transmission and radiometric sensor based sorting can selectively remove gangue minerals in different size fractions for different minerals. This paper summarizes the potential application of SBS for an iron ore in three size fractions aiming to increase the %Fe after the removal of particles with main gangue minerals associated. Pilot plant tests were carried out with samples of iron ore in different size fractions and different content of hematite and gangues. The use of x-ray transmission sensor showed the possibility to increase the %Fe from about 63% to above 68% for particles below 80mm and 45mm, after the removal of low density particles. The presence of fines on the feed affected the performance of the SBS X-rays transmission machine, especially for the fine fraction feed. The mineralogical determination, carried out to know the association between hematite and gangue minerals, and the density of the particles on the feed, can be used to preview the quality of products of the x-transmission sorting process.

Oct 3, 2019

By Antônio Augusto Gorni, Fabio Adriano da Silva, Emanuelle Garcia Reis, Afrânio Márcio Costa

Gerdau Ouro Branco´s plate mill started the operation in 2016 with high level technology. Stands out the capacity to produce different thicknesses in a same plate, therefore allowing special service for sectors such as building structures, bridges, shipbuilding and mechanical applications. The purpose of this study is to present the first results obtained in this innovative product in Brazil. Some slabs of EN10025-2 S355JR+AR steel were rolled and were evaluated the dimensional tolerances, mechanical properties uniformity, grain size, surface and internal qualities. In addition, a correlation was observed between slab and plate thickness reduction and internal plate quality. The results show that this technology can be used with adequate performance for these steel grades in the current market.

Oct 1, 2019