Search Documents

By Gordon M. Matheson

The factors which control chimney subsidence sinkhole development in weak rock were assessed by analyzing the characteristics of approximately 3000 chimney subsidence features along the Colorado Front Range. The area of study included features developed over abandoned mines in the Colorado Springs Coal Field, the Boulder Coal Field, and the Foothills District. The approximate locations of the areas studied are shown in Figure 1. Data were collected for sinkholes occurring over both room and pillar, and retreat mining areas in coal seams with a wide range of dips. The location, size, and approximate time of development of each sinkhole were documented. From these data, relationships were developed which describe the time rate of observable sinkhole development and the relative location of sinkhole development with respect to mined height, overburden thickness, and type of mining for relatively flat-lying coal seams. In addition, the observed locations of sinkhole development over steeply dipping coal seams were assessed for portions of the study area.

Jan 1, 1986

By Mark L. Chatman

The U.S. Bureau of Mines studied mineral resources of the Dragoon Mountains Unit, Coronado National Forest (54,264 ac), Cochise County, AZ. This study involves literature and field investigations with a focus on mine and prospect sites, which were inventoried and mapped; maps are contained in this report. Rock-chip samples were taken from mineralized zones and from some mine dumps; assays of the 477 samples are in appendixes. Mineral deposits are genetically and spatially related to Tertiary-age granitic intrusive activity. Most metallic mineral deposits are also strongly fault-controlled. Colored marble resources (270,000 st) are valued at approximately $6.5 million, if all were to be developed and sold as landscaping material in the form of-marble chips. However, with current demand, it is unlikely that regional markets could absorb all this material. Economic modeling of copper-zinc-silver skarns suggests none would be profitable to mine and capitalize at early 1993 commodity prices, mainly due to the small estimated size of the deposits (30,000 st to 40,000 st maximum). In the entire Unit, 140,000 st of inferred subeconomic skarn resources were estimated by USBM on five different skarn trends; measured subeconomic resources are negligible. Exploration by industry, 1992, was small-scale (on 2 skarn trends and 1 auriferous fault zone).

Jan 1, 1993

By Rachel Bernau

Water wells, aquifers, and pipelines rarely incur damage from nearby blast vibrations. Extensive ground vibrations may cause a drop in the water table thereby changing an aquifer’s structure or drying up a well. Studies on the reactions of aquifers and water wells have been performed in Montana, North Dakota, and the Appalachia Coal Region. All of these studies reported that vibrations did not change the properties of the monitored aquifers and water wells. Rather, evidence suggests that any incurred damage was caused by block motion and downsloping.

Jan 1, 2001

By John C. Machisak

DATA ON INJURY experience at quarries and related plants of the United States are presented in this publication under the following general sections: A) General injury experience: Tables 1-4: Contain current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 5-6: Current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 7-19: Current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data. (D) Selected injury data: Tables 20-30: Current data on various selected factors of operating conditions at different kinds of quarries, including employment size-groups, length of shifts, comparative severity of injuries, and injury data and related employment experience at dimension-stone and crushed and broken stone quarries, and underground quarries. (E) Mining methods and historical injury experience: Tables 31-32; Employment data and injury experience in the quarrying industries of the United States, by mining method and work location, 1953-58; and historical injury experience and employment data in the quarrying industry, 1911-58.

Jan 1, 1962

By Russell R. Trengove

The largest potential reserves of manganese in Nevada are in the Pioche district. To date, these large reserves of 10-to l2-percent manganese cannot be upgraded economically. Other large, low-grade deposits, such as the Virgin River and Boulder City deposits in Clark County, cannot be considered immediate sources of manganese. Reserves of the principal manganese deposits in Nevada, based on the most reliable estimates, total about 17 million tons analyzing 7.6 to 13.6 percent manganese. Most of the deposits are of a type that cannot be prospected systematically but have been prospected and developed in the course of productive mining operations. To realize production from low-grade deposits that are amenable to concentration, a ready market must be provided. Thus far, Government stockpiles have been the major outlet for these low-grade ores. Research and experimentation over a period of years have led to development of several processes technologically applicable to these low-grade ore bodies, but their economics is not sufficient to allow competition with imported ores on the open market.

Jan 1, 1959

By S. J. Page, R. A. Jankowski, J. A. Organiscak

The U.S. Bureau of Mines investigated the relationship of bituminous coal seam parameters and the amount of airborne respirable dust generated at longwalls. Dust and coal samples were obtained from 20 longwalls operating in geographically representative coalfields throughout the United States. Statistical analyses of coal seam parameters and airborne respirable dust measurements indicate a likely causal relationship between seam type and respirable dust. Low-ash, high-volatile coal seams were associated with higher airborne respirable dust levels. A negative linear correlation (significant at the 95-pct confidence level) was observed between the seam's ash content and airborne respirable dust, explaining up to 18 pct (R2 = 0.18) of headgate dust level variation and up to 15 pct of tailgate dust level variation. Volatile matter was found to have a positive linear correlation with tailgate dust level, explaining 16 pct of the variation. Further data examination indicates that these relationships with dust are most likely nonlinear, because of improved R2 values over the linear correlations. However, a notable portion of longwall dust production is influenced by other operational parameters, so additional research under more controlled conditions is needed to determine the seam's causative functions.

Jan 1, 1992

By B Moynihan

The Roa Opencast Coal Mine is situated at the north-eastern end of the Greymouth Coalfield. It lies on an eastern flank of the Paparoa Range, 16 km north-east of the town of Greymouth on the West Coast of the South Island. Road access is via a sealed road from Blackball to Roa, then by a 5.3 km all weather, gravel road, which gains 340 m in elevation from 190 m RL at Roa to a maximum height of 530 m near the opencast.

Jan 1, 1993

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

By R. F. Lynch, F. E. Goodwin, A. F. Skenazi

"The Gal/an alloy has been developed for continuous galvanizing of steel. The choice of the eutectic zinc-aluminum alloy with addition of misch metal gives a coating with specific characteristics as far as structure, analysis, surface chemistry and surface morphology are concerned. The performance of the uncoated Galfan coating is superior when compared to conventional galvanized particularly for corrosion resistance and ductility. For coil coating applications, these two assets are of the utmost importance but in order to benefit from these two advantages, good paint adherence and high resistance to edge creep and blistering have to be obtained. Despite Galfan's unique features compared to other zinc based or aluminum zinc based coatings, existing pretreatments and painting conditions are used with only minor modifications in order to assure good adherence and edge creep resistance. With compatible processing, Galfan can outperform galvanized and Galvalume as a substrate for coil coating as is demonstrated with various test results.IntroductionThe technical and commercial development of Galfan, a 95% zinc-5% aluminum-0.1% lanthanum-cerium hot-dip coating for steel, has been rapid. From its identification as a promising coating in late 1980, it has evolved from a research product to a fully commercial product with over 100 000 metric tons of coated sheet produced to date, and another 90 000 tons, at minimum, scheduled for 1986. The great majority of tonnage produced to date has been coil coated for use in building panel , appliance, and similar applications. Much technical work has been done to determine the suitability of Galfan for these applications and the proper way of processing sheet for best results. The present state of knowledge is discussed in this paper, along with some recent applications which are given asexamples"

Jan 1, 1987

This publication is the fourth in a series of miners? circulars covering various phases of accident prevention in bituminous-coal mines; these circulars constitute a text hook for courses of instruction on accident prevention in bituminous-coal minim. To these may be added material of particular interest in the field where the course is presented. Other circulars in the series are: Accident Statistics as an Aid to Prevention of Accidents in Bituminous-Coal Mines (Miners? Circular 47). Accidents from Falls of Roof and Coal in Bituminous-Coal Mines (Miners' Circular 48). Accidents from Hoisting and Haulage in Bituminous-Coal Mines (Miners' Circular 49).

Jan 1, 1946

By D. M. Doyle, P. J. Hannon

"The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) is a subsidiary of a five-year Economic and Regional Development Agreement, signed on June 11, 1984. The objectives of the M.D.A. are to strengthen and diversify the Nova Scotian mineral industry and to coordinate federal and provincial policies and programs. The agreement outlines the activities and responsibilities of each government, including the division of the cost (60:40, federal: provincial) between governments. The agreement established a framework for joint planning to avoid overlap or duplication of programs.The M.D.A. programs are broadly divided into five sectors (Table 1 and Fig. 1): Geoscience, Minerals Technology, Development, Firm Specific and Public Information. Each sector is administered by a subcommittee composed of one federal member and one provincial member. The subcommittees report to a Management Committee. The Canada/Nova Scotia Mineral Development Agreement (M.D.A.) Management Committee is made up of Dr. Jack Reeves from EMR and Dr. Richard Potter from the NSDME.The Geoscience subcommittee, co-chaired by Peter Giles (NSDME) and William Poole (EMR), manages the regional geologic, geochemical and geophysical studies in the province. Included in this sector are studies into mineral deposits and the basic geological relationships between mineral deposits.The Mineral Technology sector is co-chaired by the authors, Don Doyle (CANMET) and Pat Hannon (NSDME). This sector of the M.D.A. conducts studies into mineral processing, sampling, deposit byproduct commodities and project feasibility analysis."

Jan 1, 1987

By Matthew A. Baumann

Tooth-wear on mining shovels requires continuous monitoring. Worn teeth impede excavation performance, increase energy usage, and increase the risk of lost or broken teeth and adapters. A machine-vision-based automated tooth-wear monitoring system is presented. The system employs a rugged boom or stick-mounted camera to capture images of the shovel teeth. An onboard computer processes the images in real-time to determine the length of each tooth. The current wear state is available via a network-accessible log for on-demand status updates. By continuously recording tooth length changes over time, the logs can be used to estimate wear rates and patterns, permitting comparisons between different G.E.T. configurations, operator behaviour patterns, or material types. This detailed, quantitative data permits site-specific optimizations to wear packages and maintenance scheduling. Automating wear monitoring offers the crucial wear information necessary to minimize maintenance costs and reduce unscheduled downtime. A 37-day field trial in a copper-gold mine demonstrated the ability of the system to measure tooth lengths, compute wear rates, and detect differences in tooth wear based on their position on the bucket.

Nov 1, 2011

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By J. R. Kyte, L. A. Rapoport

The material balance equation for partiai or complete 1:trter-drivc reser1,oir.s been re-arranged to include a pressure irrferferencr ternr. This pressure interfernce term was ohtained from the theory established hy Morinda. A .successful progranl deissed to solve the resrclritlg c,qrration in a few hours on a nleelitr .sizeti, digital compuier. No prior knowdelge of the properties of the eqrrifer is required in the solution. 7' ri~rl calculations areatle using various assumed con!binuiions of value of the constant expretsing the qquifer properties correspoinds to the best fit ohtained between observed and calculated field history. Details of the method of calculaion are illus trated by an example. INTKCDUCTICN A method 01' calculating the material balance equation for a partial water-drive reservoir completed in an aquifer has been described in the literature." Pressure interference i'rc,m other pools iocated in the same nquiucr is not taken into account in this solution. When present, the pres- sure interference effect must be included in order to make a complete performance analysis. A correction for this effect has been developed using the theory cstahlished by Mor-tada.' Manual calculation of the material balance for water-drive reservoirs is a formidable task. Such manual ca1culation when interference eflects are includcd would be impossible to completc in any reasonable time period. However, a medium-sized stored program, digltal conlputer can he used satisfactorily. The method is described in the following sections. THECKETICAL CONSIDEKATIOhS The material balance equation for a reservoir producing by partial or total water drive, as proposed by Van Everdingen, This relationship is linear for Z/a from which thc slopc, Z, and the intercept, N, can be obtained by the least-squares method from the data points. It is not necessary lo know the aquifer properties to uktain oplimum values tor 2nd IV. Various assumptions are made tor At,,: where 11 is production time, seconds (oilfield between the equal successive time intervals into which the history is divided. t,, h It, times the number of equal time periods from i.e.. the total dimen-sionless time interval from It is noted that the dinlensionless time interval, At,,, involves all the relevant aquifer properties. Accordingly, any assunlption of is an assumption of the combined aquifer properties which pertain to the solution of the equation. Deviations of the data points from a straight line arc calculated for each assumption of and the value of A, correspond ing to the minimunl deviation is chosen as the optimum solution. This method is described in Ref. 1 and 2. Thc material balance solution is usually made with an initial assumption that the reservoir being studied is located in an infinite aquifer from which there are no other withdrawals. Deviation of the points by amounts greater than can be attributed to inaccuracies in field data may be the result of: (1) boundary effects of a limited aquifer, (2) pressure interference from othcr pools completed in the .sarne aquifer, and (3) a combination of these effects. Differentiation of these effects can be made only on the basis of geologic data. Pressure interference from other fields will result in a pressure drop at the original oil-water boundary having an interference component, The measured instantaneous pressure drops at the oil-water

By Jeane Hull

Jan 1, 2009

By Gary E. Slagel

The year was 1974. The event - the United States Congress was embroiled over what issues should be included in the proposed national surface mining law. The question - what should be done with underground mines? The leading bills ultimately addressed the environmental impacts associated with underground mines including provisions to protect the surface from subsidence impacts. Amid the fears that this subsidence language might discourage underground mining, sponsors of the bill were asked to explain the meaning of the provision that read "to prevent subsidence to the extent technologically and economically feasible." Was this an attempt to limit mining that caused planned and controlled subsidence? Former Deputy Director of the Office of Surface Mining, Dean Hunt, reviewed some of these historical events in a 1985 presentation before the Eastern Mineral Law Foundation. He reported that in 1974 Congressman Morris Udall took the floor to respond to these concerns expressed by other members of Congress and the industry. Mr. Hunt cited Congressman Udall's July 10, 1974 Congressional Record statement: "The House bill contemplates rules 'to prevent subsidence to the extent technologically and economically feasible.' The word prevent led to fears expressed by the Secretary of the Interior Morton, that the effect would be to outlaw longwall mining, with its obvious subsidence ... in fact the bill's sponsors consider longwall mining ecologically preferable and it and other methods of controlled subsidence are explicitly endorsed." Further, the report that accompanied the front-running bill, HR11500, provided the following clarification on the issue of subsidence prevention: "It is the intent of this section to provide the Secretary with the authority to require the design and conduct of underground mining methods to control subsidence to the extent technologically and economically feasible in order to protect the value and use of surface lands. Some of the measures available for subsidence control include: (1) leaving sufficient original mineral for support; (2) refraining from mining under certain areas---or (3) causing subsidence to occur at a predictable time and in a relatively uniform and predictable manner. This specifically allows for the uses of longwall and other mining techniques which completely remove the coal." It is clear from the preceding statements that Congress considered the removal of all the coal and causing subsidence in a predictable and uniform manner to be equal to or better than leaving support coal and causing no subsidence. While the actual provision in the bills talked of preventing subsidence, a subsequent exception made it clear that the real intent was to control it. This is evidenced in the specific planned subsidence language that appeared in the bills and ultimately in Section 516 (b) (1) of PL95-87, the Surface Mining Control and Reclamation Act. It reads: "...adopt measures...to prevent subsidence ... except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." In spite of this historic record that supports controlled subsidence, something has been lost in the implementation. The primary focus by many regulators over the past few years has been on the "prevent" aspect irrespective of mining method being used. This has appeared to change the original intent of Congress from one of controlling subsidence to one of minimizing damage. The objective of this report is to review some of the current regulatory issues that impede full extraction mining and offer some suggestions on possible ways to deal with these issues.

Jan 1, 1986

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

The heap leaching of base metal ores can be applied within a number of different scenarios, each requiring its own set of parameters to be determined during the metallurgical testwork programme. The occurrence of acid-gangue reactions and its concomitant precipitation reactions is a factor common to all cases, and requires that the optimal irrigation acid strength be found that optimises the combination of extraction kinetics, acid consumption and possible premature blinding of the heap due to precipitation reactions. For the heap bioleaching of base metal sulphide ores the oxygen requirement needs to be determined for the design of the aeration system, and the operating conditions employed need to also facilitate bacterial growth over and above the acid strength optimisation mentioned above. For the heap bioleaching of chalcopyrite, the need to preserve heat in the heap becomes yet a further parameter of critical importance. For the heap leaching of uranium ore a choice is required between either chemical or bacterial oxidation, based on economic and processing factors. Frequently the operating parameters need to be determined for a circuit in which heap leaching is combined with tank leaching and/or pressure leaching. The processing implications and metallurgical testwork approach for each case is discussed.

Jan 1, 2007

By E. Douglas, V. M. Malhotra

"This report presents the results of a laboratory study undertaken to evaluate ground granulated blast-furnace slag from Algoma Steel Corporation, as a replacement for Portland cement in cemented mine backfill. The evaluation was based on the results of compressive strength tests performed on cylinders cast from mixtures made with a granulated blast-furnace slag and tailings from four different mines in the Sudbury basin. Various percent¬ages of slags and various binder to tailings ratios were used.Tests results show that, in terms of compressive strength, the slag performs as well or better than Portland cement as the binding agent in cemented mine backfill. Lime was found to be a poten¬tially good activator for ground granulated slag in mine backfill applications.A field test was conducted at one of the mines, consisting of placing a mixture of 95.5% ground granulated slag and 0.5% lime into a stope, and inspecting the floor slab as it hardened. The slag performed as expected, considering the backfill mixture proportions used and the preparation of the test site."

Jan 1, 1989