Search Documents

Jan 1, 2003

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

Ferruginous manganese deposits have been known at Ripon Hills since the late 1950s. The main group of deposits occur in an area 6 km by 5 km and these were extensively investigated by Longreach Metals N.L. during1971 and 1972 for possible commercial exploitation.Ripon Hills is a dissectcd fault plateau 350 m above sea level formed by the uplift of a block of gently dipping Proterozoic shales, cherts, and dolomite. The plateau consists of chert breccia which is underlain by massive dolomite. The shales which are ferruginous and manganiferous overlie the chert breccia but are now only preserved, in places, in the broad depression and valleys of the plateau.The ore deposits occur as supergene replacement of the shales and were investigated by geological mapping, grid percussion and diamond drilling, and bulk beneficiation testing. Iron and manganese oxides erraticallyreplace Shale accompanied by the leaching of other minerals. The ore is composed of fine grained pyrolusite intergrown with fine grained hematite and locally containing extensively altered bixbyite and braunite. Thegangue mineral is mainly kaolin.The average grade, using a 15 per cent Mn cutoff, was 19 4 per cent Mn and 25·9 per cent Fe for a combined drill-proven, indicated, and inferred tonnage of 56,000,000 tonnes. The average depth of this mineralization from the surface is 11 m. Using a cutoff grade of 20 per cent Mn the average grade was 24·6 per cent Mn and 23·0 per cent Fe for a combined tonnage of 12,000,000 tonnes to an average depth of 8 m.The substantial drop in reserves occurs because a high proportion of the mineralized material contains less than 20 per cent Mn.It was shown that whereas the lower grade ore, despite erratic fluctuations in grade, could be beneficiated to specification grade by crushing, screening, and conductivity ore sorting, the higher grade ore could be beneficiatedto specification grade by crushing and screening only. The utilization of the higher grade ore was considered to constitute a more viable operation.There is potential for high grade manganese ore to be discovered in the Ripon Hills area at the contact of chert breccia and underlying dolomite.

Jan 1, 1977

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By Matthew Wallin

A part of the East Bay Municipal Utility District?s Folsom South Canal Connection Project, 430 feet of raw water pipe was installed using micro tunneling beneath the Mokelumne River. The access shafts for this crossing were constructed 50 and 35 feet deep through very dense sands and soft sandstone and siltstone. High groundwater and the immediate source of recharge from the river required watertight shaft construction methods. The shaft contractor, Drill Tech of Antioch, CA, used a brand new Bauer cutter-soil mixing (CSM) rig to construct the large shafts. The structural concept is similar to secant piles, but instead of creating cylinders of soilcrete, the CSM rig creates interlocking rectangular panels. This technology has been used previously in Europe, Asia, and Canada, but this was the first project to use CSM technology in the United States. Cutter-soil mixing technology has other applications beyond shaft construction, including retaining wall construction and levee reinforcement.

By J. Humphrey

Introduction The weight of a Mining Truck can be affected by field modifications, the selection of items like tires, rims or even the conditions in which it operates. Truck performance and the compliance with a number of ISO standards, e.g. braking, steering and ROPS are dependent on truck weight. It is critical that truck owners understand the impact of changes in weight1. What makes this even more difficult for owners to evaluate is that there is no standard terminology or definitions for Mining Truck weights. This paper discusses and defines weight terminology, how it applies to performance and standards and the impact on the application of Mining Trucks.

Jan 1, 2007

By Hongjie Yang

The No. 10 metro line of Shanghai city is 36 kilometers in length and will pass through the operating airport runway by using tunnel boring machine with earth pres-sure balance mode. Although there are examples through world that tunnels pass through airport runway and tunnelling underground is not a difficult undertaking technically, there is rare experience in China for the similar projects especially in Shanghai saturated soft soil region. Shanghai soft earth is famous for its high compressibility, high rate of water content, weakness in strength, large deformation and different characteristics in earth strata. Besides, the whole construction process will be under ultra-large airplane dynamic load on the surface ground over the tunnel, which increases the risks of construction process. This paper evaluates the feasibility of building the metro tunnel under such an extremely serious condition, especially the subsidence of ground surface caused by advancing of tunnel boring machine, which also is the most important control target for the safe operating of the runway. Furthermore, this paper discusses the effective measures to keep the settlements in the permissible level during the whole working period for the tunnel from aspects of plan, design and construction.

By A. M. Ghodgaonkar, P. J. Bhonde, R. D. Angal

Primarily ferrochrome is used to introduce chromium into steels and alloys. Chromium enhances hardness, hardenability, corrosion, abrasion and wear resistance of the steel. High carbon ferrochrome is one the cheapest sources of chromium, which finds large consumption in foundries and steel plants. However, carbon leads to problems viz. weld decay and sensitization of steels at elevated temperature causing catastrophic failure. Thus high carbon ferrochrome which otherwise enjoys financial edge over its low carbon grade is not suitable for final alloying or adjustment of chromium content. Subsequently, its addition burdens a steel maker. Hence, metallurgists around the globe have researched on finding out suitable technique for refining of ferrochrome. Traditional production methods of low carbon ferrochrome have drawbacks i.e. high refractory consumption, losses of chromium in slag and fumes etc-. Later these were overcome by adopting relatively new methods namely, metallothermic reduction, triplex process, vacuum technique to directly produce extra low carbon ferrochrome. Authors have carried SWOT analysis of the aforementioned techniques in the literature. Key Words: Ferrochrome, carbon content, low carbon grade, chromite, sensitization

Jan 1, 2007

This paper describes the economic study of longwall versus bord and pillar mining using all continuous miners for a colliery located at the South Coast district of New South Wales, Australia. In this district longwall mining appears to be a better economic proposition than bord and pillar. The internal rate of return on investment is found to remain approximately constant for each method irrespective of life. The economic importance of percentage extraction of coal is shown to be small for high values of minimum rates of return, becoming more significant as the minimum rate of return decreases.

Jan 1, 1980

By J. S. Meyer

Although salmonid fishes (including Pacific salmon and trout) have only intermediate sensitivity to copper (Cu) for traditional toxicity endpoints (survival, growth, and reproduction) and thus do not ?drive? the freshwater Cu criteria (e.g., see species-sensitivity ranking in US EPA 2007), Cu concentrations as low as 1 to 2 µg/L have been reported to impair olfaction (the sense of smell) in salmonids in laboratory experiments using dilute fresh water (see references in Meyer and Adams 2010 and DeForest et al. 2011). Olfaction is crucial to predator avoidance, recognition of kin, and reproductive synchronization (Baldwin et al. 2003); and Cu is of general ecotoxicological concern because it can be present in acid/mine rock drainage, industrial and municipal effluents, agricultural runoff, and urban stormwater runoff (Meyer et al. 2007). Therefore, there is public concern that the current regulation of Cu in surface waters is not stringent enough to protect salmonid fishes against olfactory impairment (e.g., OSU 2007; Pearson 2007). Because the toxicity of metals to aquatic organisms is a function of water chemistry [e.g., acute toxicity of Cu generally decreases as pH, water hardness (Ca2+ + Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase; Meyer et al. 2007], hardness-based freshwater criteria for metals are lower at lower water hardness. The recently-developed biotic ligand model (BLM) explicitly takes into account all four of those water chemistry parameters and the concentrations of other major inorganic cations (Na+, K+) and anions (Cl-, SO42-) to predict the acute toxicity of cationic metals (e.g., Ag, Cd, Cu, Ni, Pb, Zn) to aquatic organisms; and the BLM has been adopted by the U.S. Environmental Protection Agency (US EPA) to calculate acute and chronic national freshwater criteria for Cu (US EPA 2007). Consistent with observations of Cu toxicity to aquatic organisms, BLM-based Cu criteria generally are lower at lower pH, water hardness, alkalinity, and DOC concentrations. Therefore, although threshold concentrations for olfactory impairment by Cu can be low in dilute fresh waters, the corresponding hardness-based and BLM-based Cu criteria for the same waters also tend to be low. This leads to a logical question: Are Cu criteria already protective against impairment of olfaction in salmonid fishes, thus obviating the need to decrease those criteria even lower to protect against adverse effects to this physiological/ecotoxicological endpoint? Herein, we demonstrate that in all studies conducted to date, the US EPA?s BLM-based freshwater Cu criteria would have been protective against olfactory impairment in salmonid fishes, but the US EPA?s hardness-based criteria would not always have been protective. This distinction is important because all 50 States in the USA still use hardness-based Cu criteria in their water quality standards, and only some of the States allow use of the BLM to calculate site-specific Cu criteria. Additionally, in the absence of empirical results for calibration of a saltwater Cu-olfactory model, we demonstrate that a proposed unified freshwater-saltwater Cu-olfactory BLM predicts the US EPA?s current saltwater Cu criteria would be protective against olfactory impairment caused by Cu in sea water.

Feb 27, 2013

By Dorsey Lyon

I. INTRODUCTION. In presenting, this paper the writers wish to call attention first of all to the fact that the electric furnace was not developed as a competitor of the combustion furnace, but: 1. For the purpose of doing high-temperature work which it is not possible to do in the combustion furnace; and 2. For the treatment of ores from deposits which. are located in regions where fuel is scarce and costly, and where hydro-electric power is comparatively cheap, as is the case in Chili, in Canada, in certain parts of this country and Mexico.. This paper is not presented with the idea of trying to. prove that the electric furnace should replace the reverberatory or the blast furnace as used at present in the smelting of copper ores, but that it may be substituted for their in those localities which are not favorable to them,) and where either of the two following conditions may exist: (a) A district remote from railway transportation. facilities, and where there is a deposit, or deposits, containing sufficient values to warrant their being worked, but which, due to the cost of getting coke in for operating a smelter and of getting ore out to a smelter, have to remain unworked.. And where, on the other hand, there is plenty of water power which call he developed at reasonable cost for the production of electric power, by the use of which for. smelting the ores in an electric furnace, with subsequent Bessermerization if necessary, a concentrated product may be obtained, which can easily stand the necessary transportation charges. (b) Or,. comparatively speaking, the transportation facilities may be all right, but the cost of fuel be too great to permit of the ordinary methods of smelting, whereas,- on the other hand, hydro-electric power can he developed: in the district at a, low cost,, and the ores could be smelted by the electric furnace at a cost. that would make their treatment possible. With these possibilities in mind we have attempted to make a brief comparative study of the problem for the purpose of aiding those interested in the subject, in determining whether it would be possible metallurgically, and feasible commercially; to use the electric furnace-in those localities where, by reason: of excessive fuel costs, the cost, of operating the furnaces for smelting copper-ores. is either excessive or prohibitive. Although the smelting of copper ores in the electric furnace has received considerable attention and more or less experimental work has been done, so far as: we lire: aware there ate no electric furnaces in the United States which are' being worked on copper ores. In Norway, however, trial smeltings of copper ores with an electric furnace of 1,000 h. p. and an estimated producing' capacity of 2,000 tons per annum, have been

Jan 8, 1913

By Arnold Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970?s. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator?s area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator?s hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By S. K. Kawatra, S. J. Ripke

Bentonite clay is used as a binder for iron ore concentrate pelletization. Bentonites are sensitive to cations such as calcium, magnesium, sodium, and potassium that are known to be dissolved in the moisture remaining in the iron ore concentrate. These cations affect the ability of bentonite to absorb water, as measured by the plate water absorbance (PWA) test. This paper addresses the relationships between plant water chemistry and pellet strength for a wide PWA range of bentonites. Experiments were conducted to determine the effect of concentrate moisture solute chemistry and bentonite PWA value on the wet knock and wet and dry compressive strengths of iron ore pellets. Experiments used seven different types of bentonite that had PWA values ranging from 564 to 1033. Flushing plant concentrate with distilled water to remove the dissolved cations resulted in increased pellet strengths, to a widely varying degree, for each bentonite tested; wet knock values increased an average of 92% and dry compressive strength increased an average of 46%. In addition, pellet strengths were not found to be directly related to the ability of bentonite to absorb distilled water, measured by the PWA test.

Jan 1, 2002

By Ángel Bravo

La simulación es un programa virtual que permite evaluar los costos de perforación y soldadura para el costo final del proyecto minero. El modelo fue diseñado en hoja electrónica, cuyos datos de entrada son estándares de perforación y voladura, tipo de equipo, ciclos de minado, ciclos de avance en túnel, método de explotación, sección de túnel, costos, etc. En este sentido, el presente texto describe el diseño de simulación que buscará determinar la flota óptima de jumbos, asi como la organización óptima para asegurar una máxima utilización de equipos y establecer un sistema de mantenimiento y servicio de máxima disponibilidad. Su función de probabilidad está orientada específicamente para un método de explotación o tunelería.

Sep 13, 2001

By Corry Goumans, Dwayne Wallace

"On July 1, 1997, a rockslide occurred on the I-40 in Hayward County, North Carolina that completelyblocked all lanes and disrupted traffic flow in the region. Remedial measures were undertakenimmediately in order to open traffic, however on-going geotechnical investigation revealed stabilityconcerns that necessitated closing the highway to ensure public safety. Access to the top of the slope was available only from the bottom of the slide on the Interstate I-40. Excavation and trim blasting started from the top and along the west slope of the failure, however, additional geotechnical evaluation indicated that slope stability remedial measures were required to support the western rock slope mass."

Jan 1, 1999

By M. B. Wechsler

An analysis is developed for determining the maximum loading, as well as the potential uplift of the piles on bridge pier foundations. There are considered piers supported on two through seven rows of piles, and related to two simply supported collinear superstructures of any structural material. The study leads to different types of influence lines for various load combinations. For load combinations containing vertical loads only, the related influence lines are similar to those as for the bending moments of a virtual span covering the two actual spans, as well as the gap between the two superstructures; and, in this case, the heavier loads should be positioned in the vicinity of the pier. While, in the case when vertical loads are acting together with hori­zontal forces, the related influence lines will indicate where the heavier live loads should be positioned. And they will also indicate on which portions of the spans the live load should be avoided.

Jan 1, 1989

By Jack Parker

Critical width Before we go further into pillar design, we should look into the matter of "critical width," because of its effect on pillar behavior. Critical width refers to the greatest width that the rocks above the mine can span before failure or, if there are pillars, the width to which we must mine before the pillars accept the full weight of the overlying materials. There are theories to help calculate that probable width, and they usually boil down to one-quarter or one-third of the depth of cover; but they don't always fit, and it would be better for us to understand the factors that control local conditions. Critical width may be controlled by the thickness or strength of one or more of the strata above the mining horizon. In a gold mine, we might have a thick granite or basalt above us, perhaps capable of bridging across most or even all of a small ore body. In that case, pillars might have to support nothing, or perhaps just the weaker or damaged rock below the strong main roof. Obviously it would be wrong to design for tributary load on pillars based on some lab-determined rock strength. In some coal mining districts in Utah, huge steps can be seen in the mountain sides, with slopes on weathered shales and vertical cliffs 100 or 200 ft high in thick, hard sandstones. The sandstones are capable of bridging across hundreds of feet, often making mining deceptively easy at first, but it becomes more difficult as greater areas are opened. Sometimes such a mining sequence leads to violent bumps and bursts as the wide spans of sandstone sag and bear down on the working faces, like giant nutcrackers, or as bridges eventually fail, releasing much pent-up energy.

Jan 1, 1993

By KEITH BARRONI

In the proposed criterion for coal a distinction is made between brittle and "psuedo-ductile" failure. This criterion is the basis for the development of new equations for coal pillar strength, including a transition from brittle fracture to pseudo-ductile yielding. In addition the equations obtained allow the critical minimum pillar dimensions to be calculated to avoid "catastrophic" and "ultimate failure".The validity of these formulae can be tested by comparing their results with pillar case histories derived from the literature.

Jan 1, 1988

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

By M. B. McClenaghan

"This paper summarizes diamond exploration techniques used in glaciated terrain, focussing on indicator mineral and geochemical methods applied to glacial sediments. Understanding the ice flow history, depositional history, and stratigraphy of glacial sediments is essential to successful sampling, interpretation and follow-up of indicator mineral and geochemical anomalies related to kimberlites. Kimberlite indicator minerals survive glacial transport over long distances and the relative abundance of each mineral in till is a function of the primary mineralogy of individual kimberlites. Indicator mineral distributions observed at a regional scale define the net effect of glacial dispersal, often along different ice flow directions. Local-scale distributions define individual dispersal trains. The medium sand (0.25 mm to 0.5 mm) fraction of heavy mineral concentrates, * GSC Contribution No. 2002028 prepared from glacial sediment samples, is best suited for indicator mineral surveys. The application of till geochemistry to diamond exploration is increasing because it is significantly cheaper than indicator mineral analysis and it can be performed quickly. The <0.063 mm (silt+clay) and 0.5 mm to 2.0 mm (coarse sand) fractions provide the best geochemical contrast between background and kimberlite-rich till. Kimberlite pathfinder elements that provide good contrast include Ni, Cr, Ba, Co, Sr, Rb, Nb, Mg, Ta, Ca, Fe, K, Ti and LREE, the relative importance of which will depend on kimberlite composition and that of the surrounding bedrock.IntroductionIn Canada, glacial erosion is the principal means by which kimberlite and its associated minerals have been dispersed, from a few tens of metres to tens of kilometres down-ice. Post-glacial weathering has had little impact on kimberlite debris in the glacial sediments, thus boulder tracing, indicator mineral methods and trace element geochemistry of the fine fraction of till (“drift prospecting” methods) can be used to detect kimberlite dispersal within areas covered by glacial sediment. This paper provides a summary of drift prospecting methods for kimberlite exploration in glaciated terrain, and includes examples of reconnaissance- , regional- and local-scale kimberlite indicator mineral and till geochemical distribution patterns.Weathered kimberlite is more susceptible to glacial erosion than the surrounding bedrock, thus many kimberlites in glaciated terrain are found in low or swampy ground, under small lakes, or covered by thin (< 1 m) to thick (>50 m) glacial sediments. Glacial erosion has removed varying amounts of the pre-glacially weathered kimberlite and, in some cases, the hard competent kimberlite below. For example, glacial erosion of the Peddie, McLean and Seed kimberlites near Lake Timiskaming, Ontario, removed pre-glacially weathered kimberlite, leaving a polished striated subcropping surface (McClenaghan et al., 1999a). In contrast, glacial erosion of the B30 kimberlite, near Kirkland Lake, Ontario (Fig.1), was much less vigorous and left a >10 m cap of soft and highly weathered dark green clay-rich kimberlite (McClenaghan et al., 1996). The thickness of remaining pre-glacially weathered kimberlite will influence the geophysical signature of the kimberlite."

Jan 1, 2002