Search Documents

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By D Craw, J Pope, B Peake

Southland contains over 70 per cent of New ZealandÆs recoverable coal resources, and an investigation into the potential effects of coal mining on SouthlandÆs water resources is therefore of interest. This paper investigates pit-lake water quality in relation to current mining activities within the sub-bituminous coal and lignite deposits of Southland.   Water quality data was collected from pit-lakes in sub-bituminous and lignite deposits from October 2005 to March 2006. After periods of settled weather, turbidity increased with depth at the sub-bituminous pit-lake (10 - 21 NTUs from 5 - 30 m). In the stratified sub-bituminous pit-lake in March 2006, heavy rainfall caused higher turbidity in the epilimnion than the top of the hypolimnion (20 NTU vs 13 NTU) reflecting surface water runoff (up to 1993 NTUs) and epilimnion mixing. In contrast, turbidity at the lignite sites was variable due to the shallowness of the lakes, but noticeable increases following disturbance and adverse weather were recorded. High turbidity at the sub-bituminous deposits was attributed to the presence of clay minerals such as kaolinite whereas turbidity at the lignite sites was more likely short term and a result of heavier minerals such as quartz.   Trace element concentrations at both sites were low when compared to mine waters in other coal areas in New Zealand and no samples exceeded ANZECC water quality trigger values for 80 per cent species protection. Pit-lake water pH levels were lower and more variable in the lignite deposit (4.18 - 7.30 vs 7.24 - 8.98 in the sub-bituminous deposits). In the lignite pit-lakes, higher concentrations of trace elements (eg Dissolved As - 0.034 ppm and Dissolved Mn - 1.09 ppm) and lower pH (ÿ4) were observed at the bottom of active pits compared to inactive pits. It is possible that quartz pebble conglomerates containing sulphide minerals within the lignite seams are responsible for this.   Further investigation into the mine waters, waste rock and lake sediments will help get a better understanding of the results observed and long term processes that occur.

Jan 1, 2006

By D. Hopkins, D. Türler, R. D. Giauque, W. B. Davis, M. Karaca

In a highly collaborative research and development project with mining and university partners, sensors and data-analysis tools are being developed for rock-mass characterization and real-time measurement of mineral content. Determining mineralogy prior to mucking in an open-pit mine is important for routing the material to the appropriate processing stream. A possible alternative to lab assay of dust and cuttings obtained from drill holes is continuous on-line sampling and real-time x-ray fluorescence (XRF) spectroscopy. Results presented demonstrate that statistical analyses combined with XRF data can be employed to identify minerals and, possibly, different rock types. The objective is to create a detailed three-dimensional mineralogical map in real time that would improve downstream process efficiency.

Jan 1, 2002

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

By D. M. Doyle

"In this paper I will summarized the Falconbridge Nickel Mines1) energy costs and consumption data by fuel, process, cost centre and estimate our future costs and consumption patterns 2) detail the distribution of electrical energy 3) distribution of other forms of energy 4) describe present and planned energy conservation schemes; and 5) discuss economic justification and responsibility.There is sufficient material in this presentation to warrant several technical papers, however we felt that an overview of all our data and endeavors on the subject, would be most beneficial to those companies formulating energy conservation plans. The data briefly referred to in this slide presentation can be found in the technical paper.Over a five year period, total energy costs will vary between $63 and $94 MM depending on the future rate of energy cost escalation. An unrealistic 32% reduction in energy consumption is required to hold our own in the years ahead whereas an attainable 10°;, reduction in energy consumption would save $9 MM over this five year period.Total energy consumption, tonnage of ore delivered to plants and their ration BTU’s per ton of ore, are graphed for the years 1973 through 1976 and forecasted for the 1980’s. In 1974 we along with other member companies of the Mining Association, determined our purchased energy per ton consumption rate and set, as our goal, a 20% reduction by 1980. The dotted lines calculated from the energy audit, based on 1976 data shows there is a potential for a 10% increase in energy per ton. This could result from a lower than forecasted mining rate and operation of the new roasting, electric furnace and acid recovery facilities installed for environmental considerations at designed capacity."

Jan 1, 1978

1. Domestic Production and Use: In 1983, 12 companies operated 27 primary aluminum reduction plants, with 4 firms accounting for 65% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Maryland, New York, Ohio, and West Virginia 35%; Tennessee, Alabama, South Carolina, and North Carolina 14%; other central States 16%. Based on published producer prices, output of primary metal in 1983 was valued at over $5.7 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 37% of domestic consumption in 1983, transportation 19%, building 17%, electrical 9%, consumer durables 8%, and other uses 10%.

Jan 1, 1984

By D. J. Hutchinson, M. Lato, M. Diederichs

Light Detection and Ranging (LiDAR)-based applications for geomechanical purposes have recently proven to be a highly reliable and accurate form of remote analysis and documentation. The ability to remotely collect, process and evaluate rockmasses for structural geomechanical applications has benefits ranging from safety to efficiency, and provides a permanent record that can be assessed before and after an excavation has been completed. With the collaboration of Queen’s University and Rio Tinto, the Iron Ore Company of Canada (IOC) mines in Labrador City, Newfoundland and Labrador, evaluated the practical application of the I-Site 4400 LiDAR equipment, in conjunction with the Vulcan geotechnical module for geomechanical purposes. The project provided a comparative analysis between conventional hand-mapping and digital analysis. The analysis indicates that digital mapping could be employed as an active tool within the general geotechnical workflow, where results would be used in pit wall and rockmass support designs. As well, the field work enabled the generation of effective operational guidelines and protocols to maximize scanning efficiency.

Jan 1, 2009

By G. H. Keith

Electrowon tungsten powders were investigated with respect to consolidation, fabrication, and mechanical properties. Sheet, 0.03 inch thick, was produced and its tensile strength measured between 250° and 1,935° C. The large particle size of electrowon tungsten effectively precluded sintering to a density sufficient to allow hot working to sheet or bar. The powders were consolidated by die pressing to 70-percent density, sheathing in molybdenum, and high-energy-rate extruding to either round or sheet bar of 100-percent density. The material was then rolled conventionally to sheet. The mechanical properties of the sheet prepared from the electrowon powders compared favorably with those reported in the literature for sheet prepared from commercially produced hydrogen-reduced powder.

Jan 1, 1970

By M. K. Eryadin, I. Yildirim, R. Asmatulu

Novel dewatering aids were tested on various coal samples from the U.S. and Canada in laboratory and pilot-scale filtration experiments. The reagents substantially improved the dewatering kinetics and reduced the cake moistures. The cake moistures were typically reduced from 20-30% by weight to 8-14% range in vacuum filtration. When the reagents were used in conjunction with a pressure filter, higher degrees of moisture reductions were achieved. In the present work, the novel dewatering aids were tested using different types of pilot-scale vacuum filters. The results were consistent with those obtained in laboratory experiments.

Jan 1, 2003

By W. Kint

More than 10 years ago, one of MECS?s current partners KVT developed the so called SULFOX process for cleaning waste gases containing sulfuric compounds. In this Wet Acid Process (WAP) compounds such as SO2 and H2S, CS2, COS are oxidized over catalyst bed(s) to SO3 and finally sulfuric acid is formed. The individual plants are designed according the feed gas concentrations and customers requirements to keep the investment and operating costs as low as possible. MECS strongly believes the technology we propose will meet all your expectations. Thanks to our vast experience in the construction of sulfuric acid plants (MECS built over 800 sulfuric acid plants worldwide) we were able to design you a very reliable installation. MECS is offering the metallurgical industry, besides our conventional acid plant technology (for strong SO2) and our DynaWave? scrubbing technology (for very low SO2), a SULFOX wet acid plant (for the mid range SO2 concentrations) including an optional upstream DynaWave gas cleaning plant if required. See the figure below. Besides providing advanced technology, MECS is the only company who designs and manufactures its own key critical equipment. We manufacture our own catalyst, mist eliminators, acid distributors and coolers. Because of our in-depth technology knowledge, we understand the critical aspects necessary for making optimum equipment designs. With this combined supply of technology and key critical equipment, we can make a single overall guarantee second to none other in the world.

Jan 1, 2009

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been investigated on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27 degrees between each tuyere, and five side tuyeres with an angular separation of 22.5 or 27 degrees between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By Christian Ottergren

"Modern crushers offer double the capacity and performance of classic models. In some cases crushers are replacing SAG circuits, the advantages being smaller investment and lower operating costs. Is Tertiary crushing replacing SAG milling as the most optimal grinding method? Does tertiary crushing achieve the same outcomes as SAG milling? This paper considers these questions and provides an assessment of the strengths of tertiary crushing in comparison to other methods. Two case studies: a Scandinavian Platinum Project, and CODELCO, are also presented.INTRODUCTIONResearch on basic parameters in crushing started at Chalmers University in 1993. The initial project has developed and now involves several related areas. Modelling in accordance with new theories has resulted in modified designs which have been implemented and shown improved performance at operating mines in Chile. Sandvik Rock Processing is a partner and a major supporter of this program. This paper will cover some of the achievements and give references to the research reports.The mining industry has for many years mainly used crushers of the traditional 7’crusher concept, with thread adjustment of the setting and with a spring or hydraulic overload system. This machine type has been the workhorse for crushing throughout the world. The explanation for the dominance of this machine is that it has a reliable mechanical design. It can be estimated that about 2000 crushers of this design are still at work.Technical development in all fields utilizes new technologies like high-strength materials, advanced control systems and more extensive use of hydraulics. This is the reason why today’s motorcars, for example, are more efficient, more reliable and more environmentally friendly than their predecessors in the 1950s. Crushers are no exception. This paper will cover experience from the latest-generation cone crushers developed by Sandvik Rock Processing.The parts in this paper related to the CODELCO ElTeniente copper mine in Chile are coauthored with responsible personnel from the operation at the mine."

Jan 1, 2004

By L. "Andy" Anderson, Stephen N. Short, James E. Friant

Since the introduction of "boxhole" drilling in South Africa in 1973, the concept of a blind raise, drilled upward from below, has become an accepted mining practice. A combination machine, capable of constructing raises to a mining level below, or blind raising upward from a single setup position adds a further dimension in versatility. A machine with these dual operating modes was designated by The Robbins Company as the 53R and was introduced into the Western Deep Level Mines, South Africa in 1984. The unit is powerful (200 hp) and compact (18,000 lbs., in a 10 ft x 4 ft 5 inch x 4 ft 6 inch package). This paper describes the design considerations for the new machine, provides field data from early trials, and looks briefly at its overall market and potential.

Jan 1, 1985

By V. M. Shick

For practical purposes of the use of information resources in the field of geomechanics and mine surveying with accepted mining technology in mines, the authors have developed the packaged software programs of the survey-geomechanical information system with database objects of mine field. This system enables to execute the graphical representation of workings layout in preset scale, axonometric projection, the zones of higher ground pressure: program packages for calculations of rock pressure manifestations and for selection of suitable support facilities for the permanent, development and active workings and vertical shafts based on the information resources of the State Research Institute of Mining Geomechanics & Mine Surveying (VNIMI). The program packages are applied at coal mines in Russia and in Kazakhstan. The profitable operation of coal mines can be reached only by the combined optimal engineering decisions in mine working's laying-out and their reliability and safety at the stages of their designing and exploitation, and with minimal harm of the environment as well. This problem is being complicated by the fact that today the mining-practicing engineers and designers are ordinarily facing the problem " of an information barrier", when the complexity of controlling systems exceeds the potentialities of traditional management of production practice. Coal mine is a typical representative of complicated systems, because the information about geological structure, physicomechanical properties and stress-strain state of rock mass are of fragmentary character and insufficiently reliable. A mine has a developed network of interrelated workings, by the way, some of them are productive ones being subjected to control to a certain extent, and some of them are abandoned ones being noncontrollable and hazardous in rushes of water, gas, pulp and fire. The ground pressure forces cause the disintegration of rock mass growing with depth. The progress of mining operations constantly changes the geomechanical situation forming the zones of bearing pressure, stress relieving, coal falling, as well as it leads to the pulp movement on the earth surface, breaks the ground water flow, causes deformations and changes in stability of buildings, constructions and natural objects on the earth surface. One should take into account the existence of hazardous zones within the mine field, i.e. the zones of elevated ground pressure, geological dislocations and those ones under natural water reservoirs, ponds, etc. Major coal seams are prone to rock bursts, sudden outbursts, bleeding, endogenic fire. It is obvious, that in practice it is extremely difficult to account for the mentioned above factors in their interrelation.

Jan 1, 1996

By Weber P, Sneyd S

The total world steel production in 1998 amounted to approximately 780 000 000 t. The share of electric steelmaking was in the range of 35 per cent and is expected to increase further to over 40 per cent of the world's production within the next ten years. As electric steelmaking is primarily based on the use of scrap and as it is progressing more and more into higher steel grades the need for low-residual metallics will become increasingly important. Consequently, the demand for scrap substitute material will increase, reflected in the world wide spate of interest for DRI (Direct Reduced Iron) and HBI (Hot Briquetted Iron). The increased significance of DRI/HBI as a substitute for steel scrap has obviously emanated also from its comparatively lower and more predictable costs per ton and definable chemistry. In 1998 already 37 million tons of DRI/HBI were globally produced.

Jan 1, 1999

By J. Sammut, T. G. Joseph, R. Andreev, M. Curley

"Decisions regarding mining method and subsequent choice of excavator must take into account the quantitative factors of productivity, availability, and capital, operating, and maintenance costs. Dig performance was compared between a hydraulic excavator (HE) and electric rope shovel (RS) of similar size class (i.e., use the same amount of energy to excavate a unit quantity of the same material from a mining face), focusing on the quantitative factors above. Machine performance, normalized to bucket capacity, was assessed as a function of hours of service (60,000 hours per machine). Results showed higher production rates for the HE of similar capacity and age. In general, the RS exhibited lower service cost per volume capacity, though it had higher capital cost. The RS became more cost effective than the HE of similar capacity within approximately 30,000 hours of service. ¦ KEYWORDS Cost, Electric rope shovel (RS), Excavation, Hydraulic excavator (HE), Surface mining RÉSUMÉ Les décisions concernant la méthode minière à adopter et le choix ultérieur d’un engin d’ex¬cavation doivent tenir compte des facteurs quantitatifs de la productivité, de la disponibilité ainsi que des coûts d’investissement, d’exploitation et d’entretien. Cette étude compare les performances en termes d’excavation d’une excavatrice hydraulique et d’une pelle électrique à câbles de même taille (qui utili¬sent par exemple la même quantité d’énergie pour creuser une quantité unitaire du même matériau dans un front de taille), en se concentrant sur les facteurs quantitatifs susmentionnés. La performance de la machine, normalisée à la contenance du godet de volume unitaire, est évaluée en fonction des heures de service (60 000 heures d’activité par machine). Les résultats montrent des taux de production plus élevés pour l’excavatrice hydraulique d’une capacité et d’une ancienneté similaires. De manière générale, la pelle électrique à câbles affiche un coût d’entretien par capacité volumique inférieur, mais son coût d’in¬vestissement est plus élevé. La pelle électrique à câbles devient plus rentable que l’excavatrice hydrau¬lique d’une même capacité au bout d’environ 30 000 heures de fonctionnement. ¦ MOTS CLÉS coût, excavation, excavatrice hydraulique, exploitation à ciel ouvert, pelle électrique à cablesINTRODUCTION The most common excavating tools in surface mining operations are the hydraulic excavator (HE) and electric rope shovel (RS). In general, electric RSs are more reliable and cheaper to maintain (P&H Mining Equipment, 2007), but where complicated geological conditions exist, HEs are preferred because they are generally considered to be more mobile."

Jan 1, 2019

Disseminated gold mineralization in the Vunda River area 12 km SE of Lautoka in Viti Levu occurs sporadically in shoshonite volcanics within an alteration area of some 6 km2. No definite intrusions have yet been located though possible intrusions occur toward the centre and on the eastern margin of the area. The nature and distribution of alteration suggests the presence of a co-magmatic mineralizing stock just below the surface.The gold occurs within close spaced fractures and occasionally around the c1asts of breccia and agglomerate.Various types of alteration compatible with porphyry mineralization occur, but to date show no zoning or defined correlation with incidence of gold which occurs in various alteration facies.It is suggested that the gold and trace copper mineralization at Vunda arises from the sub-volcanic intrusive phase (monzonite) of the Sambeto shoshonite (5 m.y.) and is part of an E-W zone of porphyry-type mineralizationtrending easterly to the Kingston porphyry copper deposit at Navilawa.There is a close similarity between the Vunda mineralization and some of the porphyry deposits of alkali affinity in British Columbia, Canada.

Jan 1, 1978

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959

By D. E. Welcome, T. W. McDowell, R. G. Dong, S. F. Wiker

Workers using vibrating hand tools have the potential for developing health problems associated with repeated forceful actions and exposures to hand-transmitted vibration. Hand-arm vibration syndrome (HAVS) and other hand-arm system disorders have been associated with such exposures.1-2 To better assess health risks, comprehensive evaluations of these exposures must include quantitative assessments of hand-tool coupling forces; unfortunately, no standardized method for quantifying hand forces exists. Handle instrumentation may be ill-suited for some field environments. Psychophysical force-recall techniques may provide alternatives to handle instrumentation. A thorough understanding of the effects of vibration and other factors on force-recall accuracy and reliability is important before such methods are applied in risk assessments. Methods In this study, the effects of vibration and other factors on the accuracy of psychophysical force-recall were explored in two experiments. Twelve male subjects participated in the first experiment. The second experiment employed 20 participants (10 female, 10 male). In each experiment, participants applied specific grip and push forces to an instrumented handle mounted on a shaker system. Participants were exposed to sinusoidal vibration at frequencies that ranged from 0 Hz to 250 Hz. Three levels of applied force (low: grip = 15 N/push = 25 N, medium: grip = 30 N/push = 50 N, and high: grip = 45 N/push = 75 N ) and two levels of vibration magnitude (low: ANSI 4-8-hr limit and high: ANSI <0.5-hr limit)3 were examined. During the vibration exposure period, participants were provided with visual feedback while they attempted to “memorize” the applied grip and push forces. At the conclusion of the vibration exposure/force memorization period and a controlled rest period, the participants tried to duplicate the grip and push forces on a non-vibrating handle without the aid of visual feedback. The effects of different vibration frequencies, vibration magnitudes, and grip and push force levels were tested in a random order from trial to trial. Results Participants tended to overestimate grip and push forces. Depending on exposure conditions, error means ranged from 2 N to 10 N. The ANOVA revealed that force-recall errors for exposures between 31.5 Hz and 63 Hz were significantly higher than those at other vibration frequencies (p < 0.05). The frequency effect is depicted in Figure 1. Error means were greater when participants were exposed to the higher vibration magnitude (mean = 9.1 N, 95% CI = 8.2-10.1 N) when compared with the lower vibration magnitude (mean = 4.9 N, 95% CI = 3.9-5.8 N) (p < 0.05). The effect of vibration magnitude is shown in Figure 2. The average error for

Jan 6, 2006

By Jerry Wallace

The goal: At an industrial site, sever a well pipe containing an interior obstruction in a timely, cost effective manner by using a shape-charge to cut through the casing more than 50 meters below ground surface from the outside, doing so while inside a larger pipe, without damaging the larger pipe. The problem: Pumps and retrieval tools stuck nearly 50 meters below ground surface inside a 305 mm diameter by 9.5 mm wall thickness water well casing. The well, depth of 185 meters, had to be inspected for contaminates then properly decommissioned before industrial expansion could take place overhead. The limitations: A 508 mm diameter pipe had been driven around the 305 mm pipe to a depth of 63 meters. The usable internal diameter of the larger pipe was about 480 mm while the smaller pipe had buckled at one point forming a 350 mm wide spot. The charge thickness was limited to less than one-half the difference. Additionally, water that filled the annular space between the two pipes had to be displaced for the charge to work properly. The solution: Enlist the support of the shape-charge manufacturer to design, build and test a charge to work under the conditions present, then make it work in the field.

Jan 1, 2000