Search Documents

By R. E. Robinson

A novel variation of the GYPCIX process for the treatment of the acid mine effluent water from Grootvlei is described, in which a number of valuable by products can be obtained and the product water can be used for a variety of different purposes. A conceptual case study is presented in which the important cost parameters are described and certain critical path activities are indicated in order to derive a Return on Investment evaluation according to methods previously published. The study indicates that the treatment costs can be dramatically reduced, provided that proper utilization of the by products is taken into account. There are many possible uses for the water. However, by far the most advantageous contribution to the RDP and the best return on capital is derived if the water is used to establish small-lot farming activities providing work opportunities for thousands of people and contributing several hundred million Rands to the GDP. Vastly improved social conditions will be generated in an area of Gauteng that is in danger of rapid deterioration and a contribution will be made to maintaining mining activities in this area. The environmental impact is positive.

Jan 1, 1998

By S. E. Olsen, M. Tangstad

The main source of Mn in raw materials for SiMn production is Mn-ore and Mn-rich slag from the high carbon FeMn production. The amount of slag per tonne of SiMn metal is mainly determined by the ore/slag ratio. Increasing share of FeMn slag at expense of Mn-ore will lead to larger slag/metal ratio in the SiMn process. High volume of slag leads to an increased consumption of energy and probably to higher losses of metal inclusions in the final slag. Excavation of a SiMn furnace has shown that only modest pre-reduction of Mn-ore with CO gas seems to be obtained. Nearly all reduction of MnO was finished at the top of the cokebed. Dissolution and reduction of quartz obviously takes place in the cokebed zone after the main reduction of manganese oxide is finished. Probably the ?pick up? of Si in the metal is quite fast and takes place as the metal trickles down through the cokebed towards the metal bath. The distribution of Si between SiMn alloys and multicomponent MnO-SiO2-CaO-Al2O3-MgO slags is mainly determined by the process temperature, the silica content of the slag and its R-ratio = (CaO+MgO)/Al2O3. As an example, the equilibrium content of Si in the alloy will increase by about 6 % if the R-ratio is reduced from 2 to 1, provided constant temperature and silica content. The effect of temperature is also considerable. The equilibrium content of silicon will increase by approximately 6 % per 50°C in the temperature range 1550°C to 1700°C. The equilibrium content of MnO in SiMn slags depends first of all on the temperature and secondly on the silica content of the slag. At 1600°C the MnO content decreases from about 9 % at silica saturation to a minimum of about 3-4% when the silica content is reduced to about 40-45%.

Jan 1, 2004

By K. Ford, R. Urquhart, D. Hobbs

CIS countries are home to some of the world's largest producers of chrome, manganese and silicon ferro alloys and leading suppliers to world export markets. The region's ferro alloys production is rising faster than demand from its domestic steel industry - unit alloy consumption in domestic steelmaking is in fact falling as process efficiencies improve - and there is significant spare capacity available to increase production. CIS producers enjoy certain strategic advantages in the production of ferro alloys - for example, captive ore sup-plies, low power and labour costs - but must also meet certain challenges - such as lower labour productivity and greater distance to market than some of their competitors. CIS producers are ambitious but new investment is needed to upgrade some aging plants and overhaul outdated process technologies if they are to be more competitive with the world's leading producers and address the environmental issues that are now moving up the agenda. This paper describes the structure of the region's ferro alloys industry and discusses its advantages and disadvantages by alloy and by country. It considers how the ongoing process of restructuring and new investment in the industry might move forwards, based on its strengths and weaknesses, technical and environmental factors and the strategies of the main players. It asks how the industry might maximise its substantial potential - in particular, for the production of chrome and manganese ferro alloys - and examines the implications this holds for all global ferro alloys players.

Jan 1, 2007

By R. B. Throndycraft

"1. Belt-Drop Agglomeration Preferred at Heap Leach Operations. The agglomeration method now preferred at heap leach operations utilizes belt-drops along conveyors. Belt-drop agglomeration is being designed into numerous upcoming heap leach operations. It offers substantial capital cost savings over previously favored drum agglomerators. It has such significant operating and maintenance advantages that some drum agglomerators have been retired in favor of belt-drops.The majority of heap leach operations are now built with crushing included in the flowsheet. If crushing is included, belt-drop agglomeration can be added for almost no cost. The agglomeration equipment is simply a few conveyor transfers, designed to provide the tumbling and rolling action which forms the agglomerates. Controlled water sprays are needed at each of these agglomeration transfers. Cement or lime is added as a binder, to stabilize the agglomerates. This reagent is also needed to raise pH to safe operating levels.Addition of the pH control reagent before stacking the ore offers a reagent cost benefit. In the belt-drop mixing technique, the ore is intimately mixed with the lime (or cement). After stacking on the heaps, when the cyanide solution is sprayed onto the high-ph ore, very little cyanide is consumed. Without the pre-addition of lime or cement, the leach solution is sprayed onto neutral ore. The mixture of high-pH leach solution and neutral pH ore causes the solution pH to drop, releasing cyanide gas. This release is minor from a safety viewpoint, much less than dangerous, but the gas release is a costly waste of the cyanide reagent. Pilot-scale comparison tests were made at Pinson. Ore pre-treated with lime or cement showed 30% less cyanide consumption than untreated ore."

Jan 1, 1989

By Remo Grandori

The Umiray Angat 13,2 km long tunnel in Philippines have been bored through extremely variable and difficult ground conditions including a number of special events. In particular the following adverse conditions were found: faults in decomposed ground, high temperature rocks, extremely rapid and important convergence phenomena, water inflows up to 800 litres per second. The special El Nino climatic conditions caused a long dry season and lower the level of the lake that was granting the access by barge to the site under the minimum navigable level. Many equipment have had therefore to be transported to site by a 10 ton capacity helicopter, after having been partially dismounted. For the same reason most of the tunnel drive have been bored servicing the site by 1 ton capacity helicopters to transport materials, spares and personnel. In order to overcome the above geological and logistic problems several innovation were introduced and tested in this project. Despite all that difficulties the 13,2 km of tunnel were bored in about 24 months, with a global average of 500 m/month.

Jan 1, 2001

Methods for Improving the Flotation Recovery of the Coarse Fraction of a Nickel Ore

Sep 13, 2010

By Svato Prochazka

Content: ? commonly used drive systems ? drive system efficiency ? introduction to SR technology ? SR drive system advantages Commonly Used Feeder Drives Technologies ? VFD + induction motor ? hydraulic drive + hydraulic motor SR drive + SR motor

May 1, 2010

By Leon Maday, Robert Robinson, Judy Cochran, Don Davis

Over the past 20 years, several soft-ground tunnels have been successfully completed in the Seattle area. These tunnels were built using design-bid-build contracting methods, and have benefited from advancing technologies in exploration, design and construction methods. Owners have utilized various contractual means to share some of the risks that are inherent to tunneling projects. This has helped to foster a competitive bidding environment and to resolve issues related to unanticipated underground conditions in a fair manner. This paper presents case histories of tunnels constructed by King County and the Washington Dept. of Transportation that illustrate a common approach to design and construction issues. The common thread is successful project completion with minor cost changes under the design-bid-build contracting method. Lessons learned from these projects are being applied to the upcoming King County Brightwater Project tunnels, Sound Transit’s Light “Link” Rail tunnels and other tunnel projects.

Jan 1, 2005

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By D. W. Dew

Billiton Process Research has carried out extensive research over the past four years to develop new process technology using bioleaching for extraction of copper and nickel from their sulphide concentrates. Continuous pilot scale and laboratory batch testwork has been carried out with adapted mesophile bacterial cultures at40°C?45°C, moderate thermophile cultures at 50°C?55°C and thermophile cultures at 65°C?85°C. Pilot scale work has demonstrated the commercial viability of mesophile cultures for bioleaching of secondary copper sulphide and nickel sulphide concentrates. Moderate thermophiles offer benefits in terms of reduced cooling requirements for commercial reactors and, in the case of bioleaching of nickel concentrates, some selectivity over bioleaching of pyrite. Continuous pilot scale testwork has shown that thermophiles achieve efficient bioleaching of primary copper sulphide and nickel sulphide concentrates, giving much higher recoveries than achieved by bioleaching with a mesophile or moderate thermophile culture.

Jan 1, 2000

Ontario Operaations Mining Garson Stobie Copper Cliff North Copper Cliff South Creighton Mcreedy East Milling Clarabelle Mill Smelting Smelter Matte Processing Anode Casting Refining Copper Cliff Nickel Refinery Port Colborne Cobalt Refinery

May 1, 2007

Mineral Processing Engineering Education in China - Bringing up the Engineering Diathesis and Design Competence of the College Students

Sep 13, 2010

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

By David Smith, Bernie Martin

The Queens Bored Tunnels consist of 11,000 feet of 19'-6" inside diameter tunnels mined through rock, mixed face and dense glacial till, constructed with bolted gasketed one pass reinforced concrete liner. The tunnels are to be excavated with a pressurized face TBM, either EPB or slurry. The construction of the tunnels will require ground stabilization in the mixed face area, instrumentation and monitoring of railway infrastructure, underpinning of bridges, relocation and protection of utilities, demolition of some industrial buildings, construction of open-cut approach tunnels and emergency exits and vent plants. The purpose of this paper is to describe the scope of work, the suggested methodology and the proposed construction schedule.

Jan 1, 2005

By S. Janisko

Studies have linked long-term inhalation of diesel exhaust with adverse health effects such as cardiovascular disease, cardiopulmonary disease, and lung cancer. Diesel exhaust levels in underground mines can approach 100 times the environmental level and are therefore monitored closely in the mining industry. Elemental carbon (EC) (a product of diesel combustion commonly referred to as ?soot?) has proven to be a good indicator of diesel exhaust levels. The current procedure for measuring EC levels involves taking personal samples from a mine worker?s breathing zone and/or stationary samples in various parts of the mine and subsequently sending these samples to a lab for analysis by NIOSH 5040 method. Unfortunately, the whole process can take up to several weeks to complete. To address the problem of waiting weeks for results, NIOSH?s Pittsburgh Research Laboratory is developing a portable device for measuring levels of elemental carbon. This optical device takes a continuous sample of air in the surrounding environment and measures the absorbance of light passing through a filter that collects diesel exhaust particulates within the instrument. This technology can provide a near real time measurement of EC with accuracy within 10% error. The ability to take near real time measurements, combined with the instrument?s portability (currently small enough to be worn on a miner?s belt), makes this device extremely useful in the mining industry.

Jan 1, 2009

By Rudiger Baltz

The sudden failure of bodies of rock is a serious problem commonly experienced in the international mining industry. These explosive releases of energy are referred-to as ?bumps?, ?outbursts? and ?rockbursts?. Rockbursts can occur at such a rapid speed that they present a direct threat to safety in large parts of the mine workings. The build-up of excess stress within the body of rock can be attributed to different causes. In shallow workings, for example, sudden and violent failure of the roof strata can be caused by leaving insufficient pillar width when practising room-and-pillar mining. At much greater working depths, as it is the case in the German coal industry, rockbursts are generally attributable to high levels of rock pressure. This can even result in coal outbursts when driving individual roadways. More than thirty years ago the German coal industry suffered from numerous rockburst incidents which caused many deaths and serious injuries. This led directly to the establishment of the Rockburst Prevention Centre, which was created at the instigation of the mining companies and the chief mines inspectorate. The consistent logging and analysis of all rockburst incidents has led to the development of a system that is still used as a basis for preventing underground rockbursts and minimising the risk of such phenomena occurring. Working closely with the mining authorities and mining companies the accredited experts of the Rockburst Prevention Centre have played a key role in helping to develop and implement a range of methods for the early detection and prevention of rockbursts.

Jan 1, 2008

By L. E. Lynd

Ilmenite concentrates prepared from beach and dune sands of Florida, India, Australia, and other localities deviate to varying degrees from the theoretical composition of pure ilmenite, and generally contain more TiO2 than the formula FeTi03 would indicate, and some Fe2O3. This variation in composition is due to different amounts of altered ilmenite in the concentrates. (') The alteration has been shown to take place by oxidation and leaching of the iron in ilmenite, to yield residual products consisting of amaphous or very finely crystalline titanium dioxide and ferric oxide. Other studies(2) have stressed that ilmenite may alter first to an amorphous titanium-iron oxide, or to an amorphous mixture of titanium and iron oxides, with later alteration to crystalline titanium dioxide. There has been some speculation as to whether alteration of ilmenite is usually caused by weathering or by hydrothermal pr0cesses.(3,4,5 Three main methods of approach were used to study the mechanism and rate of ilmenite weathering. (1) Etch tests were used to learn the relationship between crystallographic orientation and the rate of chemical attack on ilmenite. (2) Altered ilmenites in New Jersey sands were compared with ilmenite in rocks of the area from which the sands were probably derived. (3) Experiments were carried out to determine at what rate, and by what agents, originally fresh ilmenite could be altered in the laboratory under simulated weathering conditions. ETCH FIGURES ON ILMENITE CRYSTAL PLANES A rather large ilmenite crystal from Sannidal, Norway, about 11/2 x 11/2 x 2 inches, bearing a few natural faces with imperfect surfaces, was prepared for etching by grinding and polishing crystal planes whose Bravais-Miller indices (referred to hexagonal axes) had been determined by X-ray methods to be 00.1, 10.0, and 10.2. Metallographic examination showed that the crystal was homogeneous, and uniform in orientation, except for the presence of twin lamellae which were oriented with their broadest surfaces parallel to the 00.1 planes of the large crystal. Since ilmenite is rather inert to standard etch reagents, strong solutions of hot sulfuric acid and cold hydrofluoric acid were used. Preliminary tests established that better etch figures were obtained using HF than with H2So4 solutions. The etch figures produced on 00.1 and 01.0 planes of ilmenite by etching 3 to 5 minutes in cold concentrated HF solution are shown in Figures 1, 2, and 3. The figures on 00.1 are "etch hillocks", rather than pits, and according to Honess(6), this phenomenon

Jan 1, 1961

By S. Felderhof, W. S. Vaughan

"Over the years, it has been increasingly difficult for the minerals industry to raise the necessary capital for its activities. To alleviate this phenomenon, complete transparency and capital market efficiency is needed. Since a company’s mineral resources and mineral reserves base is an essential component to obtaining capital, reporting these assets must also be transparent and efficient. This must occur, however, at an international level given that mineral industry operations, and its financing, are international. To achieve this, an international committee (i.e. Australia, Canada, South Africa, the United Kingdom and Europe, and the United States) was formed and has been developing standards for the reporting of mineral resources and mineral reserves.The effectiveness of these standards, however, depends on adoption by the required regulators. Unfortunately, these standards have not been recognized by the U.S. Securities and Exchange Commission (SEC). Instead, the SEC adheres to its old standard (Industry Guide 7), making it increasingly expensive and difficult for international mining companies to obtain capital in the United States. Compounding the problem is the SEC’s influence over the current work of the International Accounting Standards Board and the International Organization Organization of Securities Commissions. These organizations are in the process of standardizing international accounting practices and international securities rules and regulations. Their current position may prevent adoption of the industry-developed mineral resources and mineral reserves standards which are internationally recognized."

Jan 1, 2005

By A T. Yuniar, C A. Brannon, N D. Pascoe, H H. Firdausi

This paper describes the key components of the Grasberg Block Cave (GBC) mine design and the development and construction status of the mine. Drawpoint production from GBC will be initiated in 2018 following the closure of the Grasberg open pit. Full production of 160 000 t/d is planned for 2024, which will make it a 20-year time period between initial access development in 2004 and full production.Diluted ore reserves are about 1 Bt at a grade of 1.0 per cent Cu and 0.78 g/t Au. The mine plans some 2400 drawpoints on a 20 m × 30 m drawbell spacing in a 700 000 m2 footprint using the El Teniente layout. The drawpoint opening sequence includes five production blocks, the first two of which are scheduled to be undercut simultaneously in 2018. Ore is transported using diesel-powered load-haul-dumps to a series of orepasses and then delivered via loading chutes to a rail haulage system, which delivers the ore to a three gyratory crusher complex. Crushed ore is transported to the mill stockpiles via dual inclined conveyors.Development and construction of the substantial fixed facilities are now well underway. Primary access for personnel and materials is via the 6 km Ali Boediardjo (AB) adits. A service shaft will hoist personnel and materials from the AB adits level to the various operating levels. Shaft commissioning is scheduled for late 2015. The rail haulage system installation and construction is in progress and is due to be commissioned in 2017, which is timed to coincide with the commissioning of the ore handling system. Ventilation is provided through a series of large intake and exhaust drifts, and two of the four main fans have been commissioned. A 1600 L/s pumping system will manage drainage from the mine.Other key facilities include separate shops for rail and rubber-tired equipment, warehousing, a powder magazine, a main control centre and an underground concrete batch plant.CITATION:Brannon, C A, Firdausi, H H, Pascoe, N D and Yuniar, A T, 2016. Development and construction update of the Grasberg block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 625–634 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Virtual Reality (VR) simulations are excellent tools for training, education, simulation of abnormal and dangerous conditions in mines and solving complex problems. Although the concept of VR has been around for nearly half a century, it has taken recent advances in hardware and software to bring this technology to within the budgetary reach of ordinary users and researchers. VR is now successfully being used in the minerals industry for: data visualization, accident reconstructions, simulation applications, risk analysis, hazard awareness and training. The Institute of Sustainable Minerals Industry, Advanced Computer Graphics and Virtual Reality Research Group (SMI-VR) at the University of Queensland, established in late 2000, has been involved in developing VR applications for the minerals industry in conjunction with various research centres. This paper illustrates the benefits of using advanced computer graphics and VR techniques in the minerals industry with some examples of applications developed.

Jan 1, 2003