Search Documents

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

Commercialisation of outcomes from research projects is a process often poorly understood and managed, but has the potential to achieve significant benefits for the industry and community as a whole. JKTech Pty Ltd was established in 1986 to transfer viable research outcomes from the Julius Kruttschnitt Mineral Research Centre (JKMRC) at The University of Queensland, Australia. This paper describes successful and unsuccessful examples of commercialisation by JKTech over the years, and draws some conclusions as to the factors that contribute to success and failure in technology transfer.

Jan 1, 2012

By Diane M. Doyle-Coombs

In late July 1985, air samples from a sealed portion of the Quinland coal mine in West Virginia showed the presence of carbon monoxide (CO). Mine Safety and Health Administration (MSHA) personnel concluded that a fire was burning behind the seals. Since an imminent danger existed, the mine operator was given a closure order. The gases behind the seals were monitored and almost 2 million ff of carbon dioxide (C02) gas was pumped into the sealed area to stabilize the environment. Sixteen days after the closure order was issued, MSHA allowed the mine to return to production. Approximately 1 yr later, mine management submitted a seal breaching request to MSHA in order to drive a set of entries to further develop the mine. The Bureau of Mines established a sampling strategy and monitored gases from behind the sealed area during the breaching operation until the atmosphere was safe. This report is an account of the seal breaching conducted by the mine, MSHA, and the Bureau. The logistics of this event, the sampling strategy, and the equations applied could be used by the mining industry in future breachings or mine recovery operations. Time to reenter the area was calculated by using the methane (CH4) concentrations sampled at the discharge of the seals. Tracer gas was used to verify the ventilation flows through the area.

Jan 1, 1988

By G. E. Geiger

The purpose of this research was to develop a computer simulator fur predicting the air quality in existing coal mines as well as a design aid for developing new mines. In addition to the air quantity flow, the other variables of tempera Lure, moisture, methane and respirable dust are necessary to determine the air quality. An additional feature of this simulator is that it allows parametric studies of these variables to explore the effect that these variables have on the air quality of an operating mine system. The research has also pointed out arias where more research is needed, and promote better and more systematic data taking techniques. Wang and Hartman (see Reference 9, on page 1-98 of Section 1) had already published a computer program to determine the ventilation of large mines, and Wang and Saperstein (see Reference 10 on page 1-98 of Section 1) later published a refinement of the work in the previous reference. These references were the starting point of the simulator developed by this present research effort, and Section 1 of this report is a slightly modified version of the original vent elation program. The modifications were necessary to permit the additional programs of temperature-moisture, methane and dust to be

Jan 1, 1972

By Martin D. Conyac

A 1984 Bureau of Mines investigation identified ho mineral resources in the Wilderness Study Area (WSA). However, four prospects in the WSA contain anomalous amounts of copper and silver minerals; one had traces of gold. Stratabound copper-silver occurrences appear to be prevalent. Quartz veins in the WSA locally contain trace gold, and one mine adjacent to the area produced some gold in the late 1800's. The WSA is underlain principally by Precambrian and early to middle Paleozoic quartzites, argillites, dolomites and limestones that have been complicated by faulting, generally tilted northeastward, and thrust southeastward over sequences of late Paleozoic sedimentary rocks. The stratabound copper-silver occurrences and gold-quartz veins are in Precambrian and Cambrian rocks in the western part of the WSA, as are similar deposits regionally. Sand and gravel, and limestone are abundant, but plentiful resources of these commodities are nearer established markets. In November 1983 there were 5 small groups of current claims oh the WSA boundary; none are patented claims. Probably less than 35 claims have been located within the WSA, mostly in the northwestern portion; hut over 100 claims have been located outside, near the northwestern boundary. Oil and gas leases nearly surround the boundary and 6 extend up to 1 mile into the study area. There has been no recorded mineral production from within the WSA. From 3 to 5 miles to the west, several lode nines in the Johnnie district have produced several million dollars worth of gold from quartz veins, and some silver and lead from galena-calcite veins. These veins generally trend northeasterly and dip northwesterly and probably do hot extend into the study area.

Jan 1, 1985

By S. K. Gilman, V. E. Hugo

A common problem encountered in the mineral sands industry is that the mineralogical measurements used in defining the resource are not readily converted to metallurgical recoveries, which are used to predict the quantity of the final products. The problem stems from the different objectives of the exploration and metallurgical assessment programmes, and is often compounded by the use of different laboratory techniques and mineral definitions. Common mistakes include the misapplication of routine analysis, incorrect interpretation of mineral recovery, the confusion of mineral recovery with product yield and inconsistent definition of the same mineral. Experience has shown that unless these potential mistakes are identified, the measurement techniques used during exploration and metallurgical assessment are not compatible, often resulting in large errors in the prediction of mineral production. There are no easy solutions to the problem, as there is no universal assay technique which can cost effectively characterize all the mineral sands resources. The recommended course of action will therefore require several iterations to optimize the assay technique to suit the resource. Fundamental to the success of the measurement technique is the understanding of the mineralogy, its behaviour during mineral processing and the quality requirements for the final products.

Jan 1, 2003

By K. K. Kershner

The purpose of this investigation was to develop methods, on a laboratory scale, for recovering tin from Bolivian metallurgical slimes. Petrographic and chemical analyses were made of slime ore fractions from several well-known tin operations. High percentages of the total tin were volatilized as chlorides at temperatures below 600° C. Under optimum conditions reaction rates were relatively rapid, and the chloridizing reaction approached completion. Owing to the low temperatures involved and the high yields of tin, the process was considered to have possibilities for treating Bolivian slimes on a commercial basis. ACKNOWLEDGMENTS Appreciation is hereby extended to the Patino Mines and Enterprises, Inc., of Bolivia, for supplying slimed tin ores that were used in the experimental work. This company has since been nationalized.

Jan 1, 1959

By Francis T. Freeland

In the West many precious-metal mines are worked in patches by lessees, under conditions which closely resemble those of what is called " tribute-work" in Cornwall.* The company has its own foreman or inspector, and usually employs the engineman, blacksmith, pumpman, and perhaps other general workmen. As an inducement to work on a new piece of ground, where no ore is in sight, the company may advance a " footage"

Jan 1, 1896

By V. N. Cox, C. H. Grant

Both the underwater method and the rock cratering method contribute useful information in evaluating and comparing new explosive compositions. Results indicate that metallized explosive systems which contain no high explosives can be formulated to offer more energy and to do potentially more work than other slurry explosive systems. Commercial field trials are presently being conducted with a metallized explosive that does not contain any high explosive. Although there have been only a few commercial blasts to date, the results are encouraging. The Dow Chemical Co. has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which DOW is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of nonmetallized explosives currently being used. Early in 1960, additional patent rights were acquired from independent inventors and a development station at Virginia, Minn., was set up to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the boreholes. Due to the complexities involved in controlling the manufacture of the explosive in the borehole, performance was sometimes in doubt. Furthermore, experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over 2000 charges of 8 to 60 lb under water and in taconites and granites with many types of explosives, a metallized explosive was developed which is now being manufactured at a pilot plant in Virginia, Minn. and is being evaluated commercially. UNDERWATER METHOD An underwater method of evaluating explosives has a number of advantages. A permanent site can be established and operated indefinitely. A large number of charges may be fired in a short length of time. The medium in which the explosive is shot is exactly the same for successive shots. Data are recorded electronically minimizing human judgment. A disadvantage of the underwater method is the lack of confinement provided by the water medium. Many explosive compositions require a greater degree of confinement to develop good energy release. Although the relative significance of the two components of energy release that are usually measured, the shock energy and the bubble energy, and their relationship to breaking rock are not clearly understood, the underwater method is a valuable research tool for screening explosive compositions and gaining an insight into the manner in which explosives release their energy. Fig. 1 shows schematically the underwater apparatus. The piezoelectric gages are calibrated tourmaline crystals which convert the shock wave to an electrical impulse which is transmitted to an oscilloscope and recorded on Polaroid film. The shock traces are picked up by scopes 1 and 2. Scope 1 is timed to pick up the full trace whereas scope 2 is timed to cover the first increment of the shock trace expanded, and therefore allows full inspection of the propagation and peak pressures. Scope 3 records the bubble trace. When the explosion occurs, a bubble of gaseous detonation products is formed. The outward momentum of the water keeps expanding the bubble even after

Jan 1, 1963

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By R. B. Schluter

Drying and preheating (partial induration) the green, unfired iron ore pellets is a means of reducing the energy required to produce metallized pellets. The Bureau of Mines processed three magnetite and two hematite concentrates through the unit operations of pelletizing, preheating in air, and reduction to metal to determine the effects of preheating upon the properties of the metallized pellets. The pellets were prepared in a 16-inch-diameter laboratory balling drum. Preheating and metallization were carried out in an externally heated 4-inch-ID by 4-inch-long stainless steel drum using air for the preheating atmosphere and lignite char as a reductant. The results 'varied considerably: two of the magnetites spalled when preheated in air at temperatures of 900° C and above, and the third magnetite and the hematite flotation concentrate required complete induration at 1,300° C to produce satisfactory pellets. The earthy hematite ore yielded excellent pellets at all preheat temperatures.

Jan 1, 1972

This report, the third in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more, effectively extract and process minerals and fuels. Environmental considerations, reduced ore grades, and the related increased quantities of material handled were the dominent concerns of the minerals industry in 1972. Productivity increased in most mineral commodities as equipment became more mobile, versatile, and sophisticated. Increasingly, equipment designs incorporated health and safety features. There was considerable interest in the field of energy and in pollution-free metallurgy processes.

Jan 1, 1973

By K. H. Coats, M. H. Terhune

Analysis and example applications have been performed to compare the accuracy and computing speed of alternating-direction explicit and implicit procedures (ADEP and ADIP) in numerical solution of reservoir fluid flow problems. ADIP yields significantly greater accuracy and requires about 60 per cent more computing time than ADEP, not 300 or 500 per cent more as reported elsewhere. l,2 INTRODUCTION Several recent papers 1-3 discuss an alternating-direction explicit difference approximation (ADEP) to the diffusion equation. Example applications of ADEP and ADIP4 were reported to support conclusions that ADEP is comparable in accuracy to ADIP and requires one-fifth to one-third the computing time of ADIP. Applications of ADEP in calculation of two-phase flow in reservoirs was also proposed. 3 This study was performed to compare further the relative merits of ADEP and ADIP in simulation of two-dimensional flow of one and two fluid phases in reservoirs. Since two-phase flow equations are often essentially elliptic rather than parabolic, the efficiency of ADEP in solving the elliptic equation was also examined.

Jan 1, 1967

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

By Eric L. Trist

The objective of this contract was to review the results of the Rushton Mining experiment in work organization and design, to explore the extension of knowledge gained from Rushton to other underground coal mines, and to conduct a search for a potential mine site for a demonstration project. The primary focus of the contract was on a search process to provide the research team with the opportunity to evaluate the different potential experimental sites, in order to select one or more with the highest potential for success. This search process also provides the various levels of union and company officials the opportunity to fully understand the context of the research before making a decision on whether to participate. While the search project failed in its attempt to locate a specific mine site, the research team believes that this is not a rejection of the actual project but rather extreme caution because of the uncertainty within the UMWA.

Jan 1, 1978

By John Brown

Let’s talk about things that you, the driIl boss, the pit boss and the driller can do to eliminate the trend in drilling related accidents that have come to plague our industry in recent years. My paper will focus on reaI issues, problems and solutions that will affect our everyday outlook and attitudes about our jobs and lives. There are some real hard facts we must address if we are going to reverse this terrible killing trend.

Jan 1, 2000

By S. S. Gross

A program was conducted to determine whether sufficient quantities of the flame retardant, ammonium phosphate, could be incorporated in a water-based foam solution to prevent or delay reignition (burnback) without. significant degradation of foam properties. Up to 20% of mono and diammonium phosphate was added .to d high expansion foam solution. This mixture was applied as a high expansion foam to burning wood and coal samples. The effect of this mixture on burnback was laboratory tested by placing the wood or coal sample in front of a radiant panel. It was found that diammonium phosphate levels of 20% by weight prevented reignition without degrading foam properties. A field test was then conducted using a 20%, diammonium phosphate mixture and a control with no phosphate on a wood crib fire. The experimental foam did extinguish the crib fire faster than the control as evidenced by the smoke from the crib. However neither crib reignited.

Jan 1, 1982

ANNUAL meeting of the Woman's Auxiliary of the American Institute of Mining and Metal-lurgical Engineers convened on Tuesday morn-ing, Feb. 20, the president, Mrs. H. W. Hardinge, presiding. President Hardinge, in opening the meet-ing, said: "I have the honor and great pleasure to welcome you to our seventh annual meeting. It has been a happy year, though I started in fear and trembling. My fear is partly gone and my trembling becomes less as time goes on. Never has a chairman had such splendid cooperation and harmony in her work; no. matter how much was asked nor what the task, I have always received the same answer, `We are with you, of course we can do it.' Often the road has been untried and the way full of snares, but we have all pulled together. Is it any wonder we have had a prosperous year? I cannot thank the governing -board and officers enough for their help." Mrs. Hardinge described her trip through the West last summer, during which she visited many of the local sections of the Auxiliary. She also spoke of the work of the Rossiter Raymond memorial library which has been started as an activity of the Woman's Auxiliary. Mrs. Reynders read the minutes of the last annual meeting, and Mrs. Kemp read the treasurer's report. The latter showed that on Feb. 1, 1922, there was a bank balance of $683.61 and on Feb. 10, 1923, the bal-ance was $947.93. Mrs. Westervelt expressed the sorrow of the Auxiliary for the death -of Mrs. Florence Howe Hall and of Mrs. Levi P. Holbrook.

Jan 4, 1923

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By Pedro Lilienfeld

The objective of this program was the development, design, fabrication, and laboratory testing of a mine-worthy continuous respirable dust monitoring system (CRDMS). The operation of the sensor unit of this system is based on the light scattering intensity of the respirable fraction of airborne dust. The CRDMS is compatible with the typical environmental rigors that characterize coal mines and, in particular, the shock, vibration, impact, moisture and dust conditions prevailing at active training machines. The sampled area must be within the breathing zone of the mining machine's operator, whose dust exposure is to be monitored by the CRDMS sensor unit. Instantaneous, as well as shift-averaged dust concentrations, are displayed and recorded for later retrieval, Alarm indications and other diagnostic information are provided. The project was completed with the delivery of three sensor/display units (SDU), one data retrieval unit (DRU), two mining-machine-compatible power supplies, and two [auxilliary] battery packs.

Jan 1, 1983