Search Documents

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

The Bureau of Mines annually publishes statistical data reflecting technological trends in the minerals industry (metals and nonmetals except fuels). This report outlines recent developments and trends and the technology outlook for mining practices and metallurgical processing based on a review of the minerals industry during the past 2 years. A historical statistical series which indicates trends in the minerals industry has been extended with 1970 data. In addition, data are given from a 5-year Bureau of Mines cyclic canvass of froth flotation plants. Data for 1970 are compared with those of 1960 and 1965.

Jan 1, 1972

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among workers. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy construction equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. One hundred and eighty nine operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, the need to perform a larger survey to further substantiate the outcome, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 1, 2003

Shortly after Denny, Robson, and Irwin published their first paper in 1937, on the prevention of silicosis by metallic aluminium, experiments were begun on the practical application of the discovery.It was thought at that time that aluminium powder, to be effective in aluminium therapy, would have to be intimately admixed with siliceous dust at the latter's source. There followed several years of experimental work underground, during which the application of aluminium powder was tested in:(1) Speakers on machine columns, vibrated by drills.(2) Vials placed in drill holes to be blasted.(3) Both homogeneous and heterogeneous mixture with explosives.(4) Packages with tamping.(5) Compressed-air lines.(6) Special compressed-air ejectors for use while drilling and after blasting.(7) The discharge of ventilation fans.(8) The filters of respirators.It was concluded from this research that any adequate method of introducing aluminium powder into a mine atmosphere would require too much extra gear, supervision, and aluminium p;wder, and would interfere unduly with underground routine.Later, animal experiments by Denny, Robson, and Irwin2 showed that aluminium powder provided effective therapy when inhaled independent of silica dust. Therefore, some means of surface treatment was deemed more practical.APPARATUS USED IN THE DEVELOPMENT OF ALUMINIUM PROPHYLAXIS SAMPLINGA basic requirement was a method of sampling to assess accurately the particle-size concentrations of dispersed aluminium powder. Konimetry, though regularly practised at McIrityre, was inadequate for the research in mind. On the other hand, the efficiency of the thermal precipitator was recognized as being very high. Accordingly, the latter instrument was chosen as best suited to our needs. Through the courtesy of the Ontario...

Jan 1, 1945

By R J. Holmes

An accurate knowledge of the chemical, mineralogical and physical characteristics of ores and mineral products that are mined, processed and traded is crucial to effective resource utilisation, plant design, process optimisation and finally quality control to ensure that contract specifications are met. However, all too often the responsibility for sampling is entrusted to managers and personnel who do not fully appreciate the significance and importance of collecting representative samples for analysis, and everyone seems satisfied as long as some material is collected and returned to the laboratory for analysis. Furthermore, sample stations incorporated into the design of new plants are often the first casualties when cost cutting exercises commence. This needs to change, because there is little point in accurately analysing samples if they are not representative in the first place. The resultant analyses can be next to meaningless and the effort taken to analyse such samples is to a large extent a waste of time and resources.Ultimately, a poor knowledge of the characteristics of ores and mineral products limits the ability of mining companies to optimise the life of ore resources and plant performance, and failure to meet final product specifications can have disastrous consequences, including price penalties and more seriously loss of sales contracts. It is high time that sampling is given the attention it deserves as the first critical step in the quality measurement chain.CITATION:Holmes, R J, 2013. The importance of sampling in the mineral industry, in Proceedings MetPlant 2013 , pp 34-49 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By M C. Goode

The use of electrical or electronic safety systems to protect personnel, and the engineering tasks associated with the design, manufacture and maintenance of these systems are referred to using the term ‘functional safety’. In the past ten years, the use of such systems has transitioned from its traditional base, in oil and gas major hazard facilities, to being a part of most large mining and materials handling projects. In particular, functional safety is rapidly becoming a significant component of Australian iron ore projects, typically in the form of emergency stops, remote isolation, drive through interlock, robot cell entry or mobile machine anti-collision systems. While these types of systems have been in use in iron ore for a long time, functional safety standards (eg AS61508, AS62061, AS4024.1503) require more rigourous demonstration of the level of risk reduction provided by the systems.The early engineering project development phases require a number of key decisions to be made around functional safety implementation. The decisions made at this point in a project will go on to dictate the required types of risk assessment and analysis, equipment selection, sizing of substations, and training and maintenance requirements for owners. For project teams that are unfamiliar with functional safety, or inexperienced in its application, an incorrect decision or failure to understand the requirements of the chosen standard can lead to a failure to meet contract requirements, as well as major cost and schedule overruns.This paper examines the implications of functional safety on early engineering studies, focusing on the following questions: How does a designer or company determine what standard is best suited to their project? What key aspects of functional safety design need to be considered during project development? And finally, how can the impact of functional safety to the project be minimised?CITATION:Goode, M C, 2017. Functional safety impacts on study stages of major projects, in Proceedings Iron Ore 2017, pp 347–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By John D. Sullivan

A DISCUSSION of the developments of the past decade in the field of refractories, and the effect of these developments on the performance and life of open-hearth furnaces, is perhaps best introduced by reference to Fig. 1. This shows the most important types of refractories doing into various parts of the furnace, together with their cost, and remarks on their use. It has been estimated that half of the refractory makers market comes from the iron and steel industry, and something like one-third of all refractory brick used finds its way into open-hearth furnaces. To melt steel, a furnace capable of withstanding temperatures close to 3000 deg. F. is required. The furnace is assembled of various refractory materials selected by experience and economic considerations. Furnace structures today, from a refractory standpoint, are considerably different from a quarter century ago. Furnace operators, interested in the performance of refractories, care little how they are made or where they come from so long as they give reasonable service. But, the entire history of the refractory is important and technical knowledge of the ceramic materials used in making the refractory is necessary to the manufacturers, so that the proper article gets into the hands of the ultimate consumer.

Jan 1, 1936

By Shosei Serata

The Stress Control Method improves productivity and safety in underground coal mining. The method stabilizes the roofs and floors of mine openings in both shallow and deep coal beds, regardless of whether or not there are ground stability problems. This paper describes the means by which a tapered pillar experiment is used to collect in situ data, which is then used as input for a computer model. The resulting computer model is then used to optimize Stress Control design for the mine under study. The behavior of any underground coal mine is not elastic, as is generally conceived in the conventional view of rock mechanics, but rather is highly time-dependent and site-specific. Unfortunately, conventional rock mechanics methods based on the elastic principle are not able to capture the highly non-elastic nature of ground behavior which actually occurs. To capture actual behavior, a new method of study is required. In this regard, geomechanical study of an underground coal mine may be compared to studying the behavior of a living fish. Its true behavior zannot be understood by examining it "dead in the laboratory. It Is the "live" nature of the coal mine that is required for design optimization of the Stress Control Method in the given mine. The Stress Control Method is based on a time-dependent theory of the global behavior of the mine ground, which generally contradicts the conventional elastic theory of ground behavior. Therefore, site-specific adaptation of the Stress Control Method required a comprehensive understanding of the global behavior of the mine as a function of time and site-specific ground conditions.

Jan 1, 1986

By David P. Reddick

Economics is a social science dealing with the allocation of scarce resources. In modern times the “science” was identified by Adam Smith in his book, The Wealth of Nations, written in 1776. Mr.Smith, highly influenced by the Mercantilists of the 17th and 18th centuries, identified the “Invisible Hand” which would lead every individual to pursue selfish rewards in purchasing goods. He speculated these selfish motives would result in the best good for all. Price would be determined by barter, at a point where self-centered customers and vendors were mutually satisfied. Today, Smith’s theory is known throughout the world as “Capitalism” but most often termed “Free Enterprise” in the United States.

Jan 1, 1992

By Galen Bauer

"Up until the mid 1960's, the only available methods for making continuous weight measurements were through the use of mechanical and electro-mechanical weigh scales. It was during this time period that a new concept in weighing was introduced. It was known and is still known as the nuclear belt weigh scale.During the early days of its appearance in the market place, many things were learned about its advantages and disadvantages for weighing various materials. As with many new devices, it had to go through a ""wringing out stage"" before it became accepted by the weighing industry. Even today, even though it is a proven device, there are skeptics who believe the nuclear belt weigh scale will not survive. Let me assure you, it is here to stay.. 'PRINCIPLE OF MEASUREMENTThe nuclear belt weigh scale consists of a ""C"" Frame assembly which houses the radioactive source (Cesiwn 137) and the radiation detector (Ionization chamber). The ""C"" Frame assembly is put in place around the conveyor belt as shown in Figure 1. The radiation source emits a fan shaped beam of radiation which covers the full width of the material being conveyed on the belt. Radiation which has passed through the material on the belt is detected by the ionization chamber which is located in the lower arm of the ""C"" Frame assembly. The ionization chamber changes the radiation energy into an electrical signal which is related to pounds per foot belt loading. This signal is transmitted to a highly stable amplifier which combines the pounds per foot signal with a belt travel signal from a digital tachometer which allowed the scale user to be able to monitor total mass being conveyed. Many so-called conventional type scales use belt speed rather than travel to obtain mass per unit time, and then integrate the signal to obtain their weight signal. This unnecessary step tends to erode the overall accuracy of the weighing system."

Jan 1, 1975

By Christopher J. Bise

INTRODUCTION The transportation of men, supplies, and mined material from an underground operation is the connecting link between the mine plant and the surface plant. Unless the mine is accessed by a drift or adit, some form of hoisting system is necessary for slopes or shafts. This chapter will deal with the selection of wire ropes and hoists, two of the most important consider¬ations when designing a hoisting system for an under¬ground mine. WIRE ROPES General A wire rope is designed to transmit forces longitudi¬nally along its axis. Wire rope is used in a variety of mining applications because of its flexibility, high ten¬sile strength, and dependability. Shaft hoisting ropes and principal slope haulage ropes are usually custom-¬built; however, proper rope selection for slushers, car spotters, etc. should not be overlooked. Wire ropes for shafts and slopes, since they represent the life line for the mines, should be of the very highest quality improved plow steel. This quality is necessary to deal with the conditions of loading, winding, vibration, abrasion, and corrosion. Tables I and 2 display the specifications for the typical wire ropes used for mine haulage applications. The 6 x 19-class haulage rope is used for most hoisting where abrasion is not critical. On the other hand, where abrasion is critical, such as a slope application, 6 X 7-class haulage ropes are preferred. For other mining applications, manufactur¬ers' handbooks should be consulted. Selection The selection of a wire rope for a mining situation consists of simply applying appropriate safety factors to a calculated maximum rope pull and comparing the result to the listed breaking strength of the rope under consideration. Table 3 can be used for determin¬ing the minimum factors of safety for wire ropes. To determine the maximum rope pull, the following quantities must be known: the rope weight in pounds (x), the conveyance weight in pounds (y), and the weight in pounds of the load in the conveyance (z). These values are used to calculate the load due to gravity, the load due to conveyance friction, and the load due to rope friction. When these loads are added together, as shown in Eq. 1, the maximum (static) rope pull (RPS) can be derived:

Jan 1, 1986

By Albert L. Toenges

This paper is the third of a series4/ that describes some methods and practices of mining coal mechanically where operations are conducted on more than one shift. The mining of coal by means of mechanical devices has emphasized the need for continued study of the relationship, of these devices to existing physical conditions and to planning of the operations for increased safety and economy. The purpose of this investigation is to stud the operations of different types of mechanization used in mines under various systems of mining and physical conditions to reach conclusions as to the safest and most economical methods and practices of mining. Physical conditions very in different and in the same mining districts and determine, together with economical conditions, the systems of mining and the types of mechanical loading equipment used. The information presented in this paper

Jan 1, 1941

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By Litvinenko V. I

Being a source of structural materials for many centuries, the modern image of the ferrous metallurgy is burdened with obsolete technologies with disregard towards new environmental protection requirements. The production cycle of metallurgical products have two clear-cut stages: I . production of liquid metal and casting into steel billets; and 2. processing of steel billets in solid state under high temperature to produce various shapes and profiles of metal products. Plastic deformation of metal at the second stage is least associated with environmental pollution and is presently being provided with more and more advanced equipment.

Jan 1, 1999

By Sherwin F. Kelly

One of the most succinct and illuminating perspectives of the field of geophysical exploration to appear in recent years is an article by E. A. Eckhardt, in the magazine Geophysics for October 1949. Although his review covers the year 1948, many of the data presented are apropos to a review of 1949, and form a pertinent background for a consideration of current progress. He presents charts of the world-wide distribution of gravimeter and seismograph activity in oil exploration, which show that surveys in the United States accounted for practically 68%; of all gravity work and 80%; of all seismic activity. Canada ranked second, with a proportion of roughly 6%, in each case; South America accounted for about the same percentage of seismic work, and double that amount for gravity surveys. Within the United States, Texas and Louisiana were the scenes of the greatest activity, both claiming about 60% of all surveys by each method.

Jan 1, 1950

By E. M. Spokes

A.B. Rushton The work and resulting publications of the Committee on Underground Coal Mine Safety and The President's Commission on Coal were appropriate at the time of publication. The statistics cited in the publications appeared to be valid, and the actions proposed by the committee had merit. Although the actions proposed to achieve further improvements in safety may have been worthy of repeating, to associate statistics (Table 1) that are seven to eight years old with company names is bad. Statistics are readily available from the Mine Safety and Health Administration (MSHA) and are usually within three months of being up to date. A review of the most recent Coal Controlling Co. Report will reveal significant changes in the rankings. The more recent statistics should have been cited, or at least compared with those used in the article. Westmoreland Coal Co. is listed as having a 21.1 disabling injury rate for the period (1/78-12/80). The disabling injury rate for the Company for the year ending 1985 was 7.4 for the underground mines and 6.25 for the total facilities. Through March 1986, the disabling rate for the underground mines was 2.86. The management and employees of Westmoreland Coal Co. are committed to safety. The improvements achieved over the past five years attest to that commitment. We are justifiably proud of the achievement and dislike being misrepresented as in the April 1986 article. Reply by E.M. Spokes I regret that the lapse of time since the original work gives a picture of safety practice that is no longer true today. That Westmoreland has reduced its disabling injury rate by 65% to 7.4 in 1985 is most commendable, and I congratulate you for this accomplishment. It is typical of the progress sought by the National Academy of Science and National Research Council when they funded the original study and published "Toward Safer Underground Coal Mines" in 1982. If a significant number of companies do as well as Westmoreland, the report will have served its purpose. Since the paper was primarily a condensation of the original report, it would not have been appropriate to seek access to later statistics. The purpose in seeking its publication at the time of presentation was to reach those who might have missed the original report. The fact that publication was delayed has not voided that purpose and may have reminded some who were aware of the original that its recommendations still apply to improvement of underground coal mine safety.

Jan 6, 1986

By R. L. Virta

Six companies mined fire clay in Missouri and Ohio during 2004. Production, based on a preliminary survey of the fire clay industry, was estimated to be 398 kt(438,700 st), valued at $9.81 million. This was slightly less than the production and value figures from 2003. Missouri was the leading producer state. It accounted for more than 70 percent of the U.S. production. Consumption Domestic producers sold or used fire clay primarily for refractory applications. This application accounted for 79 percent of the market. Refractory products made using fire clay include firebrick and block, grogs, high-alumina brick and specialties, refractory mortars and mixes, and saggers.

Jan 1, 2005

By D. F. Scott

Seismic tomography, as used in mining, is based on the principle that highly stressed rock will demonstrate relatively higher P-wave velocities than rock under less stress. A decrease or increase in stress over time can be verified by comparing successive tomograms. Personnel at the Spokane Research Center have been investigating the use of seismic tomography to identify stress in remnant ore pillars in deep (greater than 1220 m) underground mines. In this process, three-dimensional seismic surveys are conducted in a pillar between mine levels. A sledgehammer is used to generate P-waves, which are recorded by geophones connected to a stacking signal seismograph capable of collecting and storing the P-wave data. Travel times are input into a spreadsheet, and apparent velocities are then generated and merged into imaging software. Mine workings are superimposed over apparent P-wave velocity contours to generate a final tomographic image. Results of a seismic tomographic survey at the Sunshine Mine, Kellogg, ID, indicate that low- velocity areas (low stress) are associated with mine workings and high-velocity areas (higher stress) are associated with areas where no mining has taken place. A high stress gradient was identified in an area where ground failed. From this tomographic survey, as well as four earlier surveys at other deep underground mines, a method was developed to identify relative stress in remnant ore pillars. This information is useful in making decisions about miner safety when mining such ore pillars.

Jan 1, 1996