Search Documents

By Albert L. Toenges

This paper is the fourth of a series5/ that describes some methods and practices of mining coal mechanically where operations are conducted on more than one shift. Many inquiries have been received regarding methods of extracting pillars with mechanized equipment, and this paper deals primarily with this phase of mechanical mining. Some of the questions that have been asked are:

Jan 1, 1942

[ ]

Jan 1, 2009

By Philip B. Grote

The deep ocean mining industry is in a pre-commercialization stage of development. In the context of a proper legal/regulatory regime, deep ocean mining system design, site survey, and operation technologies are capable of rapid evolution. The report recommends that the regulatory framework develop in parallel with the industry and presents a rationale for implementing this approach. The Government has several interests in deep ocean mining technology: (1) as a potential regulator, sound regulations should be based on an understanding of the technology; (2) as a potential monitor, survey technologies are relevant; and (3) as an estimator of strategic minerals supplies, it is important to understand the technology which allows economic access to deep ocean minerals. Thus, the major portion of the report presents an in-depth review of systems design, operations, and survey equipment and techniques.

Jan 1, 1979

By Jueun Lee, Jong-Hwa Yoon, K. Rider, Bernard J. Martin

Whole body vibration is known to affect movement accuracy [1], however little is known about changes in the organization of movement and movement strategies used to limit the influences of perturbations. The specific aim of this work is to analyze the motion and coordination of upper body segments of seated operators performing reaching tasks under whole-body sinusoidal vibration exposure and simulated vehicle ride motion. The long-term objective is to model reach coordination and predict the dynamic behavior of the upper body motion under vehicle vibration exposure. Method The reach task consisted of pointing with the right hand index finger to targets located on touch screens placed in front of the subject, 45° overhead and 90° to the right in the mockup cabin of an HMMWV placed on a 6 DOF ride motion simulator. The task was performed under stable (no vibration) and vibration (sinusoidal vibration or simulated ride motion) conditions. A motion capture system was used to record kinematic data of reflective markers to recreate body link trajectories. Joint angles (torso, shoulder and elbow; Figure 1) were then computed using quaternions. Coordination between body links was defined as a) the joints angle-versus-angle relationships between the upper arm and lower arm, and b) the joint motion onset relationships between torso, upper arm and lower arm in the time domain. Results Angle–versus-angle relationships. The relationship between upper arm vs. lower arm angle and torso vs. upper arm angle for a far forward reaching movement in the stable (solid lines) and vibration conditions (dotted lines) are illustrated in Figure 2. Fig 2A compares the control condition with a 4 Hz lateral vibration while Fig 2B compares the control condition with a 6 Hz vertical vibration. It appears that under vibration exposure the reduced upper arm extension is compensated by an increase in torso flexion. This effect is seen in the last phase of the movements (encircled areas). In addition, the lower arm extension is delayed under 6 Hz vertical vibration (Fig 2B left panel). Time of joint motion onset. The timing relationship between torso, upper arm and lower arm is largely a function of the target to be reached. Examples of delays between body links are illustrated in Figure 3. The control condition is compared to a 6 Hz vertical vibration for three

Jan 6, 2006

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A. G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids, and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue-gases, the circulating fluid bed technique with internal oil combustion at 220°F for the calcining step and a five-stage fluidized bed cooler for heat-recovery from calcines, the process gives an outstanding heat-efficiency. In a first industrial plant for 560 sh. tons/day of alumina heat consumption figures of less than 1·400 B.T.U./lb Al203 g were achieved.

Jan 1, 1972

By Phillip Martin Warren

Safety and productivity are critical factors in the performance of the Australian Mining Industry. In this sense, the paper point out that while the multiple dimensions of both training and productivity make it difficult to quantify the relationship, it is clear from this study that organizations that conduct training consider that there is a very positive link. Training is seen as a very important activity by the vast majority of organizations surveyed, and is an activity from which they consider they are gaining significant, and often very substantial productivity benefits. Therefore, it predicts well for productivity of Australian enterprises which invest in training.

Sep 13, 2001

By P J. Hommert, D S. Preece

"Commercial development of the United States Oil Shale reserve will require substantial amounts of mining. In fact, even a modest 500,000 barrels per day industry requires a mining effort equivalent to nearly half of the current U.S. coal mining industry. Obviously, mining efforts on this scale will benefit from technological advances. There are a number of areas where advanced technology could impact mining. These include continuous miners, shale transport systems, and blasting. This paperexamines recent developments in computer modeling of blasting and assesses the likelihood of these advances being applied to practical oil shale mining problems."

Jan 1, 1989

Copper ores are widespread through the Lachlan Geosyncline in New South Wales, but the size of the orebodies is generally small. The largest deposits occur in the Cobar district where an iron-rich copper ore type has been developed in Silurian sediments. Similar de- . posits to the south in the Nymagee-Mt. Hope-Melrose districts are related to quartz feldspar porphyries of probable Upper Silurian age. Deposits to the east in the Tottenham-Girilambone districts are less complex mineralogically and are possibly related to an ultra-basic source.Copper mineralization in the Highlands further to the east is often developed in Ordovician andesite or MiddleUpper Silurian acid volcanic sequences. The deposits in andesite contain considerably less galena than those in the acid extrusives; a small proportion of the mineralization in the latter has texture, mineralogy, and geologic setting analogous to the Captain's Flat copper-Iead-zinc deposit, for which both syngenetic and epigenetic origins have been proposed. Very little copper mineralization occurs within granitic material, even though rocks of this type ranging from Silurian to Carboniferous in age crop out through much of the geosyncline, and the extent of the metal contribution from plutons to the deposits in volcanics is open to question. Numerous deposits are known in the contact zone around Mid-Devonian and Mid-Carboniferous granites, however, and the formation of these orebodies has undoubtedly been influenced by plutonic activity. Small occurrences of copper with associated minor nickel sulphides are developed in a narrow serpentinite belt of possible Lower-Middle Devonian age in the southern section of the Highlands.

Jan 1, 1970

Effects of Hydrated Mg2+ on KCl Flotation

Sep 13, 2010

In 2004, a total of 741 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.1% of all operations.

Sep 1, 2007

By Gary A. Kingston

Low-cost hydroelectric energy in the Pacific Nortnwest has been an important factor in the development of a ferroalloy industry. Eleven companies, employing approximately 1,000 persons, produce about 116,000 tons (1954-58 average) annually of ferrosilicon, ferrochromium, ferromanganese, ferrophosphorus, silicomanganese, and ferronickel. About 7,500 tons (1954-58 average) of these ferroalloys is consumed in the Pacific Northwest States of Washington and Oregon; the rest is used principally in other western and mid-western markets. In 1959, the Bureau of Mines began a study to determine the current status and to evaluate the potential of the ferroalloy industry in the Pacific Northwest. The Bureau gathered information from operating alloy plants in Oregon, Washington, Idaho, and Montana; from published materials; and from consumers of ferroalloys.

Jan 1, 1962

By Bratt G. C

When zinc is electrowon from concentrates or residues of high manganese content, the zinc sulphate electrolyte may contain high levels of manganese. The manganese level is usually controlled by removal of manganese at the anode as the dioxide during the zinc electrodeposition stage.By increasing the temperature of an electrolyte containing 8 gll manganese from 35°C to 90°C, decreasing the acidity from 100 gll to 30 gll, reducing the current density from 432.A.m-2 t6 286 A.m-2 and using new lead anodes containing over 0·75 per cent silver, the current efficiency for manganese dioxide removal was .increased from less than 1 per cent to over 20 per cent.At the same time the current efficiency for zinc deposition was maintained above 90 per cent by additions of high molecular weight cationic polyacrylamides to the cell. By utilization of these conditions in a small number of cells, the manganese level in the circuit could be economically concrolled to any desired level.With these conditions the formation of the dioxide changes from an indirect route, via Mn04-, to a direct oxidation of Mn2+ to Mn02.The incorporation of impurities such as Pb, K, NH4, Cu, Ni, or Fe makes the deposit unsatisfactory for direct use in Zn - Mn02 dry cells. The deposit structure changes from cryptomelane at low temperature to y3-Mn02 at high temperature.

Jan 1, 1975

By Randy Wheeler

The importance of having full wave form information for recorded blast events cannot be overstated. Knowing the peak particle velocity and the frequency at the peak are the tip of the iceberg. This presentation will focus primarily on using the FFT (fast Fourier transform) for detailed frequency analysis. Employing linear superposition to evaluate timing effects on amplitude and frequency will be discussed.

Jan 1, 2005

By Steven G. Vick

Effects of the August 1995 failure of the Omai tailings dam in Guyana continue to be felt throughout the mining industry. This article is taken from the final report of the independent body of experts commissioned by the government of Guyana to establish the cause of the failure. It explains what happened, why and how to avoid it in the future. Despite environmental, health and safety effects that were negligible by any objective measure, the failure has received wide international attention. Coming on the heels of the shift in exploration targets and development opportunities to developing countries, it has intensified interest in tailings dam safety and environmental management issues. An informed understanding of the nature of the failure and its effects is key to responding to these concerns.

Jan 1, 1996

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

In the present study, we have investigated the conditions for the formation of bubble clusters and the effect of well-defined agitation on the stability of clusters. A specially designed cell was used in which bubble clusters could be formed at the surface of a porous block in a fluidized bed of relatively coarse hydrophobic silica particles. The clusters then rose through a flow field of known turbulent characteristics. The size of the clusters before and after passing through the turbulent zone were measured using a high speed camera. The influence of shear rate on the deformation of the bubble clusters was investigated. The results showed that the Kolmogarov microscale was much smaller than the maximum cluster size, suggesting that the breakage of the clusters was mainly due to interaction with clusters in the inertial convection sub-range.

Jan 1, 2009

By W. J. Birch, A. Wetherelt

The scaled-distance model for blast vibration analysis is the standard method employed throughout the surface mining and quarrying industries to model Peak Particle Velocity (PPV) data. Although empirical, the method is widely accepted and through the simplicity of its application and ease of graphical verification is set to remain a popular option. The validity of the technique relies principally on the fundamental parametric assumption that blasting data is normally distributed. Throughout the evolution of scaled-distance modelling, this is an issue that has most often been presumed rather than proven (most likely due to the tediousness of the calculations involved). In the few cases when normality has been given some degree of consideration, the result has been the product of a simple visual inspection of frequency distributions: clearly unsatisfactory. However recently the soundness of this assumption has been brought into question, with obvious connotations for blast modelling in general. This paper considers this fundamental issue and seeks to investigate the normality hypothesis within the blasting context through an in-depth statistical analysis of what possibly can be described as an ‘ideal’ blasting dataset. This being a rare case study concerning an opencast coal site in England, where for the entire life of the site every single blast was monitored and recorded through the use of permanent monitoring stations. This has provided a unique ‘total population’ dataset of considerable size from which the assumptions of normality are put to the test.

Jan 1, 2005

By Paul Worsey, Seokbin Lim

There are two major types of shaped charges, conical and linear (Ref 1, 2). Conical shaped charges are used to perforate targets and are mainly used by the military as anti armor weapons and by the oil industry for oil well perforation. In contrast, linear shaped charges are primarily used to cut metal in the demolition industry with other uses including separating devices in the space industry. There is a large amount of material published on conical shaped charges because of the high level of defense industry research and funding, however in stark contrast there is very little published on linear shaped charges.

Jan 1, 2003

THE township of Costerfield is situated in the parish of Costerfield, county of Dalhousie, and lies 6 miles east of Heathcote and 30 miles south-east of Bendigo. It is separated from Heathcote by the Mt. Ida Range, which forms the western boundary of the Silurian formation. It is situated at the head-waters of Tin-pot Creek, a small southerly tributary of the Deegay Ponds Creek, which flows east to the Goulburn River.The field was discovered in 1860 by two prospectors, Coster and Field, who were guided there by a shepherd, M Nicol Coster and Field had already discovered an antimony lode about three miles nearer Heathcote, when M Nicol offered to guide them to the larger outcrop. The main Costerfield reef at that time projected above the surface, and was white through oxidation, though the bluey sulphide showed on fracture. No alluvial gold of any consequence was obtained at Costerfield, but a little was obtained, at Redcastle, 7 miles to the north, and in some of the gullies to the east.Following its discovery there came a period of prosperity to Costerfield, while the mining operations were confined to the oxidized zone. The early success of mining at Costerfield was due to the gold values, and it is probable that the oxidized zone was secondarily enriched. The earliest available record of values is a crushing of Coster and Co. on the Antimony reef (now known as the Costerfield reef), when 200 tons from a depth of 70 ft. averaged 4 oz. per ton in July, 1861. At this time a crushing mill had not yet been erected at Costerfield, and the ore was carted and treated at Redcastle. The massive antimony ore, consisting of mixed oxides and sulphides, was separated by hand-picking as "marketable ore," and the remainder crushed for gold. A higher average is recorded from South Costerfield in September, 1861, when a 15' cwt. parcel...

Jan 1, 1922

By B. R. Mohal, S. Chander

"A new technique to determine wettability of powders is presented in this paper. In this technique the times for immersion of individual particles from air into liquids, defined as imbibition times, are measured. Through the measurements of imbibition times for a large number of particles, it is possible to determine homogeneity/heterogeneity of a powder sample with regard to its wetting behavior. Quartz particles give a very narrow distribution of imbibition times showing a homogeneous wetting surface whereas coal particles give a broad distribution indicative of the heterogeneous nature of its surface. The imbibition time measurement technique is considered to have certain advantages over other methods to determine wettability of powders in surfactant solutions. In this study we have also compared the imbibition times with the wetting rate mea¬surements obtained by a modified Walker test.INTRODUCTIONSeveral methods are available for determining wetting characteristics of sol¬ids. Each of the methods has been used in the past to obtain very valuable information for comparing wetting behavior of various solids in a given liquid or for comparing the wetting behavior of several liquids for a given solid. Each method measures a somewhat different aspect of wetting and therefore quantitative correlations between techniques have been difficult. A general approach is to use a method in which close similarity between the technique and the application (where results of wetting measurements are to be used) can be maintained. The objective of this investigation was to develop a method which could be used to determine the wetting characteristics of single particles in surfactant solutions. Wetting of individual particles is of importance in cap¬ture of dust particles by sprays of surfactant solutions.METHODS FOR DETERMINING WETTING — A BRIEF REVIEWThe various methods available for measuring wetting characteristics of solids include: contact angle, immersion/sink time, bubble pick-up, induction time, capillary rise, and displacement method measurements. Some of the methods are briefly reviewed in the paragraphs that follow."

Mar 1, 1989