Search Documents

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By D. Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 “Welded Steel Conveyor Pulleys” adequately defines standard pulleys for most aggregate material handling applications. However, many aggregate applications demand pulleys of higher capacity and reliability than that offered by CEMA pulleys. This paper examines the CEMA Pulley Standard and pulley specifications for aggregate applications requiring greater capacity and reliability than the CEMA Pulley Standard. Higher reliability increases the uptime and has a lower total cost of ownership.

Jan 1, 2003

By S. Nagamatsu

Alumina supported gold catalyst prepared by spray reaction method (spr) provides gold particle with about 20 nm of diameter. The gold particle size is larger than conventional gold catalysts. However, the spr catalyst shows higher catalytic activity for NO-CO reaction. In the present paper, we have discussed the local structures of spr-Au/Al2O3 catalyst by using Au L3-edge XANES spectra. In order to investigate the local structures of Au-sites, multiple scattering approach to XANES analysis was applied. Calculated Au L3-edge XANES spectra for fcc-Au and Au2O3 were in good agreement with the observed spectra. XANES spectra for spr-Au/Al2O3 were characterized by 4 types of Au sites (bulk, interface, surface and peripheral). In this case, almost all gold sites (> 90 %) are bulk site. The other sites are less than 10 % of gold particle. However, the experimental and the calculated results of Au L3-edge XANES spectra for spr-Au/Al2O3 require about 30 % of gold oxide or hydroxide. Bulk of Al2O3 contains a certain number of gold nano-particles, which was incorporated in the bulk Al2O3 support. In the interface area, gold oxide forms a few layers. This result was also supported by DV-Xa electronic structure calculations. The comparison of the catalytic activities of the spray catalysts and the impregnation catalyst for the NO-CO reactions imply synergy effects between gold nano-particles and alumina support.

Oct 1, 2003

By M Fahey

Large volumes of tailings are produced annually by the goldmining industry of Western Australia. This material ishydraulically discharged into large storage facilities usingsub-aerial deposition methods. Much of the gold comes fromhighly weathered rock, resulting in tailings with significant claycontents. Consolidation of these materials can be very slow,particularly if occurring under the effects of self-weight alone.To optimise the consolidation behaviour of the tailings, disposalstrategies can take advantage of the effects of evaporation byallowing each tailings layer to dry before the next layer isdeposited. In the last 20 years, much of the gold processing inWestern Australia has utilised saline groundwater. As the salinetailings dry, the surface will develop a thin salt crust. Laboratorytests have shown that these crusts can drastically reduce thesurface evaporation, adversely affecting the behaviour of thestorage. This problem has been the focus of an extensive researchprogramme, with the objective of obtaining a fullerunderstanding of the mechanisms controlling the coupledconsolidation and evaporation behaviour of saline gold tailings.Part of this study involved site investigations of a wide range ofstorages to ascertain their current states. Methods of gainingaccess to the tailings following deposition were developed.In situ testing and high quality sampling were conducted on each storage and samples returned to the laboratory for analysis. These investigations have enabled full characterisation of the storages to be accomplished. Examples of data are shown herein and the implications of the results are discussed.

Jan 1, 2001

By Robert Benedetti

This paper describes various mitigation methods in order to reduce the maximum acceleration of the floorboard of hulled vehicles when explosive charges buried in water saturated sand were detonated beneath them. The effects on floorboard acceleration of adding a vehicle hull, several types of floorboard bracing, the use of foam to fill the gap between the floorboard and hull, and the use of foam to isolate the floorboard from the hull have been investigated. Small scale testing was conducted, which used bar magnet velocity gages to measure the velocity as a function of time of the center of the floorboard, directly over the charge, where the acceleration was expected to be greatest.

Jan 1, 2012

The National Institute for Occupational Safety and Health (NIOSH) has continued study of the Personal Dust Monitor (PDM) developed by Rupprecht & Patashnick Co. Inc. through a CDC contract and currently being commercialized by Thermo Fisher Scientific. This report examines the effect of oversize particles, cyclone inversion, and cleaning procedures. Clean and exposed filters were examined using light microscopy and particulates counted before and after various instrument manipulations. The data presented show that the dry cleaning procedures do not cause significant (greater than limit of detection) sample contamination by respirable or oversize particulates and that the cyclone is resistant to particulate carry over during inversion.

Jan 1, 2009

By Martin Plante, Denis Hamel, Marie-Pier Bédard, Jeff McLaughlin

"The results and methodology for the optimisation of the zinc flotation circuit at the Matagami Mill using the 6-Sigma methodology are shown in detail while only the base line and final results are presented for the copper circuit. As a result of the six sigma project, the zinc concentrate grade was improved by 2% and the zinc recovery by 3%, with reduced dosage of reagents while the copper concentrate was improved by 2.4%. The process variation in the zinc concentrate grade and recovery was also reduced by over 50%. The main factors contributing to the project success were identified to be improvement in the plant measurement systems, an internal benchmarking exercise and statistically designed laboratory and in plant tests to guide the process improvement. The annual value to Noranda resulting from this project has been estimated at approximately $5 million.INTRODUCTIONThe Matagami concentrator started ore processing from the new Bell- Allard deposit in July 1999. Concentrator performance (grade and recovery of zinc and copper concentrates) was highly variable and work was ongoing to fix the sources of variation. In the mean time, Noranda embarked on its 6-Sigma initiative across the company. The 6-Sigma DMAIC (Define, Measure, Analyse, Improve, Control) methodology was used in the two flotation circuits to reduce variation and improve performance. The statistical 6-Sigma methodology moves towards identifying and controlling critical process operating variables (the X' s) to achieve customerspecified performance (the Y's). The goal of the methodology is to describe a process in a numerical equation known as the transfer function, given as Y = f (XI, X2, X3.. .), where Y could be concentrate grade or recovery and examples of X's are reagent dosage, particle size, etc. With the transfer function, optimal operating conditions and control tolerances are established for the key X's to ensure the desired Y performance is obtained.Each phase of the 6-Sigma methodology is explained below with examples from the Matagami project."

Jan 1, 2001

By the use of flotation tests it was confirmed that there are two functions of oxygen in sulphide mineral flotation. Sized samples of galena and chalcopyrite were sulphidized, washed free of excess sulphide ion, and then contacted with air-saturated water for certain lengths of time. The mineral was then transferred to a sealed laboratory flotation cell containing water with a known concentration of dissolved oxygen. Xanthate and frother were added and flotation continued for 1 min.Both the extent of mineral oxidation and the concentration of dissolved oxygen markedly affected the flotation of galena and chalcopyrite. The response to a change in either variable is dependent on the level of the other, but generally best flotation occurs with the maximum degree of air saturation of the pulp. Galena flotation is hindered by oxidation of the mineral beyond a small threshold amount but a similar effect for chalcopyrite was not observed...

Jan 1, 1967

By H. Lagendijk, I. J. Reinecke

Mintek was contracted by Oriel Resources plc in 2004 to conduct a preliminary assessment study on smelting ferronickel from the large but relatively low grade Shevchenko nickel ore deposit in Kazakhstan. A detailed feasibility study (?DFS?) was awarded to Bateman BV following promising results from the preliminary assessment study (?PAS?) and small-scale pilot plant test work. As part of the DFS, a total of 450metric tons of ore was collected from three different locations in the deposit and shipped to Mintek. After sampling, the bulk sample was prepared for smelting. This comprised crushing, screening and calcining with each step done separately for the three different lots. The chemical composition of the ore from the deposit is relatively high in silica and therefore falls out of the MgO to SiO2 range that is normally processed by pyrometallurgical means to produce ferronickel. The main objective of the testwork was to demonstrate that a method could be found and successfully applied to smelt these siliceous ores and produce an acceptable nickel-containing alloy. A 2-m ID DC arc furnace was installed with a twin-cathode (electrode) configuration to replicate the proposed commercial-scale furnace and also incorporated an advanced design of water-cooled copper panels in the lower furnace sidewalls to withstand the aggressive nature of the high SiO2-containing slags. The reductant used was a high-volatile coal from Karaganda in Kazakhstan. The reductant addition was adjusted to achieve a 90% recovery of nickel. In the assessment of the process metallurgy, some deviation from equilibrium conditions was observed. This deviation is ascribed to the intermittent existence of a smelting bath partially covered with feed during the testwork. Optimization of smelting conditions should result in the metallurgy (slag metal equilibrium) being closer to the theoretical predictions and make the production of a 20% nickel alloy possible at 90% nickel recovery. The solution for the successful processing of these siliceous ores was found in the attainment of the necessary operational stability through the control of arc length, operating temperature, open-bath smelting conditions and flux additions of up to 10% dolime for the most siliceous of the three ore types. The test work carried out by Mintek provided the basis for the process flow sheet and engineering design of the DC arc smelting furnaces for the Shevchenko Nickel project.

Jan 1, 2007

By T. K. Dichmann, J. A. Finch

"Microflotation, laboratory batch, and in-plant minicell continuous tests were conducted to determine if copper ions not only activate sphalerite but also depress pyrite when the minerals are together. Microflotation tests showed that pyrite recovery increased with addition of copper ions in the pH range of 5-10 when alone, but decreased when sphalerite was also present. Batch flotation tests (Red Dog ore) showed that upon addition of copper, pyrite recovery decreased significantly. The continuous tests (Louvicourt Mine) confirmed this and indicated that with excess copper pyrite recovery can increase. The results suggest there is competition for copper and xanthate in favour of sphalerite. To take advantage of this competition it may be necessary to control the sequence and rate of copper, collector, and lime addition. INTRODUCTIONFlotation, in common with all physical separations, is an imperfect process that results in misplacement of minerals. One source of this imperfection is accidental activation by contaminating metal ions. An important practical example is the misplacement of pyrite to zinc concentrates. Flotation of sphalerite generally requires activation by copper ions, added as copper sulphate. Copper ions are also used to activate pyrite [l] hence there is the suspicion that accidental activation contributes to the recovery of pyrite (Py) with the sphalerite (Sp). However, recent literature has shown that copper ions may make Py less floatable if Sp is also present. Xu et al. [2] conducted continuous minicell tests in-plant at Kidd Creek Operations (division of Falconbridge Ltd.) and showed that while the addition of copper sulphate improved zinc/iron selectivity, it did so as much by reducing the recovery of pyrite as increasing zinc recovery (Figure 1)."

Jan 1, 2000

By J. R. Thoenen

[Before 1914 Germany held virtual monopoly on the world supply of potash for fertilizer purposes. During the world War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-time prices stimulated interest n various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany and other sources reduced prices to below pre-war levels, and, as a result, most of the domestic producers ceased operational.]

Jan 1, 1941

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By John Reilly

Costs of complex/underground projects have been consistently underestimated and delivery on time and on budget has been problematic. This has been attributed, to inadequate cost estimates and unidentified and/or insufficiently managed risk. Use of probabilistic cost estimates like the Washington State Department of Transportation?s CEVP® process (developed by the author and others) has produced more realistic cost estimates, explicitly identified and quantified risk (as input to risk management plans) and early awareness of key project issues. This paper updates previous work (NAT 2004), adds implementation detail for probalistic cost estimating as used by WSDOT, FHWA and other agencies and will address key issues in risk management, as related to probalistic cost estimates.

Jan 1, 2008

By K. E. Livo, D. H. Knepper

Modern remote sensing provides a means for locating and characterizing exposed mineralized systems in many parts of the world. These capabilities are non-invasive and help target specific areas for more detailed exploration. An example of how remote sensing technology can be used is evident from a study of the Questa Mining District, New Mexico. Analysis of low spectral resolution data from the Landsat Thematic Mapper satellite system clearly shows the region-al distribution of two broad mineral groups often associated with mineralized systems: clay-carbonate-sulfate and iron oxides-iron hydroxides. Analysis of high spectral resolution data from the Airborne Visible and Infrared Imaging System (AVIRIS) shows the occurrence and distribution of many individual mineral species that characterize the pattern of hydrothermally altered rocks in the district.

Jan 1, 2004

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

By Beth Robinson

This first of two articles on the Second Mexican Mining Rail Excursion describes some of the more casual experiences participants enjoyed on last fall’s rail tour of major Mexican mining operations. In this article, Beth Robinson, a graduate student at Colorado School of Mines, describes trip organizers, participants, and some of the unique events occurring during the two-week excursion. Next month, part two of the series will highlight various Mexican mines and plants.

Jan 1, 1982

By W. Blake, J. Whyatt

Sixty years of rockbursting in the Coeur d’Alene district has taught painful lessons and led to a number of practical advances in controlling rockburst hazards. This paper summarizes those lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rockburst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rockburst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d’Alene district experience.

Jan 1, 2002

By T King

This paper reviews the changes in the coal industry over the past 30 years and attempts to predict the trends over the next ten years. The last 30 years have seen a steady concentration of production into fewer, larger mines, which operate on 3: more continuous basis, and a major increase in productivity per employee. Coal exports have increased from zero to almost half the country's total production. As well as major changes in exploration and mining equipment and the increasing use of computer tools, the industry now operates in a relatively new regulatory and commercial environment.   Safety legislation now requires the writing and enforcement of policies and procedures by the mining companies, rather than adherence to inflexible regulations enforced by an Inspector. Accident rates have decreased dramatically. The transition from coal mining licences to permits, requiring landowner consent and resource consents, is well under way. Environmental controls are now an essential aspect of the industry.   Equipment suppliers now offer maintenance services, production guarantees and flexible financing.  Contract miners offer mine design and restoration as part of the contract. In a similar approach, Solid Energy now offer an ash disposal service and assistance with resource consents to their customers as well as investment in technology to ensure a consistent product to demanding specifications. Solid Energy has proposals for energy centres which install and operate the coal burning appliances and simply sell energy to the customers. The next 10 years should see an intensification of these trends of bigger mines, more exports and greater technology and a 'package' approach to customer service.

Jan 1, 1997

CrusherMapperTM - A New Tool for Crusher Condition Monitoring The efficiency of mineral processing plants is entirely dependent on the availability of the plant equipment critical path. This typically concerns comminution circuits consisting of primary crushers and primary grinding mills. Crusher and mill availability are determined by the frequency and duration of maintenance shutdowns, which are primarily driven by the need for replacement of sacrificial liners. The change of crusher and mill liner shape over respective life cycles also strongly affects plant efficiency. It is therefore highly desirable to accurately monitor the condition of mills and crushers in order to optimise plant efficiency through maximised availability and targeted liner shape. Traditional comminution liner and other production parameter condition monitoring has been attempted through ineffective methods which prevent satisfactory management of crusher and mill maintenance and reduce operational control. This situation has recently dramatically improved for grinding mills through the development and commercial deployment of MillMapperÖ, a technology based on three-dimensional laser scanning data and dedicated software (Franke, Lichti and Stewart, 2006; Franke and Lichti, 2007; 2008; Franke, 2008; Franke, Redman, Johnson and Michalek, 2009). At the time of writing in late 2009, MillMapperÖ is in successful use at a rate of approximately 170 surveys and associated reports per annum at processing plants in Australasia, South America, North America and Africa. This paper presents the introduction of CrusherMapperÖ, the MillMapperÖ equivalent for crushers. CrusherMapperÖ also utilises high density, high accuracy laser scanning data, and features dedicated algorithms for three-dimensional monitoring of wear on crusher concaves and mantles. This facilitates the detection of wear hot spots or zones or localised liner failures, and accurate forecasting of reline tonnages and dates. It also for the first time provides the means to establish optimised concave and mantle shapes in order to achieve production targets. In contrast to any other currently utilised condition monitoring method, CrusherMapperÖ data collection can occur remotely and does not require any shutdown or crusher isolation. This method therefore does not interrupt crusher production while at the same time eliminating any confined space risk normally associated with taking measurements inside the crusher cavity.

Sep 13, 2010

By Larry Schneider

"0 ne of the incentives that led to the development of non-electric shock tube initiation systems was the desire within the industry to improve detonator safety. And to the extent that nonelectric initiators are immune to the hazards of stray current and radio frequency energy found on normal blast sites, an advancement in safety has been accomplished. However, as a cautionary note, it is important to realize that there are still many hazards associated with any initiation system. While some of these hazards may differ from those associated with electric detonators, others are identical to those associated with any type of initiation system. For instance, contrary to what some uninformedblasters may believe, lightning remains a hazard when using nonelectric initiation as well as electric initiation."

Jan 1, 1995