Search Documents

By H. Razavizadeh

The recovery of copper from oxide ores containing from 2% to 4.1% acid-soluble copper from the Sarcheshmeh mine in Kerman province of Iran was investigated by agitation leaching in sulfuric acid media. Quartz, as a major constituent, and malachite, as the major copper mineral, were identified in the ore by X-ray diffraction (XRD) and microscopic studies. A series of leaching experiments on the ore was performed over a concentration range of 10 to 20 g/L and temperatures from 15° to 50°C for a maximum of 3 hours. An initial high dissolution of copper was followed by a very slow reaction. By increasing acid concentration and temperature, the dissolution rate of copper was accelerated. However, by increasing acid concentration, the acid consumption of ores was also increased. Surface morphology of solid residues at various leaching times was examined with a scanning electron microscope (SEM). All SEM micrographs of the partially reacted particles displayed a needle structure. The kinetic studies showed that the malachite dissolution rate could be modeled in two stages. About 85% of the malachite dissolution occurred in Stage 1, while the remaining 15% occurred in Stage 2. The data obtained for the leaching kinetics indicate that the dissolution for Stage 1 was a diffusion-controlled reaction with an activation energy of about 20.6 kJ/mole, and the dissolution for the Stag 2 was a chemical-controlled reaction with an activation energy of about 87.6 kJ/mole.

Jan 1, 2008

By N. Chow

The recovery of manganese from lower grade resources has been studied for a number of years. Of key importance of prior work, was the discovery that higher valent manganese resource can be readily leached with sulfurous acid. This eliminates the need for high temperature reduction roasting that is conventionally used in processing high grade material. High temperature roasting is energy intensive, emits a large amount of carbon dioxide, and would not be economical for processing lower grade material. While the prior work provides important information to extract manganese from lower grade resources, the production of unwanted by-products, and high water and energy usage has limited its commercial use. This paper describes the results from laboratory work that demonstrate solutions to problems, which to this point preclude commercial development. Preliminary mass and energy balances show that a significant opportunity exists in producing manganese with this hydrometallurgical scheme in a low cost, environmentally friendly manner. Emphasis of the work is on low water use, low overall energy use and economic destruction of unwanted by-products.

Jan 1, 2011

The Bayswater seam of the Singleton Coal Measures is discussed in relation to its field occurrence and related li~hotype profiles. The seam is correlated throughout widely separated areas of the Hunter Valley with the Farrells Creek seam at Howick, Broke seam at Broke, and Saddlers Creek seam at Mt. Arthur. The unusual features of composition of the seam in relation to adjacent seams is dealt with in terms of the seam environment, particular attention being given to the sandstone at the base of .the seam. Petrographic and other data are used to support the arguments submitted.

Jan 1, 1973

By Richard W. Graeme, James J. Komadina

Gold Fields acquired an option to purchase the Cerro Corona project, located in Hualgayoc, Cajamarca Department, Peru, in December 2003. In January 2006, the option was taken up and the transaction closed. During the intervening months, project development occurred against the backdrop of a presidential election, increasing national social activism and environmental regulation, rapidly escalating operating and capital costs, as well as an unprecedented demand for engineering and technical skills. Project “Lessons Learned” are discussed in the context of an evolving strategy. The Cerro Corona project forms part of a porphyry copper-gold deposit situated within the Hualgayoc Mining District in northern Peru. It is located in the highest part of the Western Cordillera of the Andes, close to the headwaters of the Atlantic Continental Basin. It lies approximately 90 km (56 miles) by road north of the Department of Cajamarca’s capital city and near the village of Hualgayoc. Access to the Cerro Corona project from Cajamarca is by two roads, one from Cajamarca to the Yanacocha Mine 45 km (28 miles), and then from Yanacocha to the village of Hualgayoc and the town of Bambamarca 45 km (28 miles).

Jan 1, 2007

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By J. E. Kogel

Industrial minerals play a central and dual role in the sustainable development (SD) of natural resources. Over the past decade the mining industry has increasingly focused on sustainably extracting and processing industrial minerals. This trend has been driven by higher energy costs, diminishing water resources and sensitivity towards environmental stewardship. Industrial minerals have been used throughout human history as low cost, naturally occurring, materials. Today they are critical components of recycled packaging, energy efficient building materials, light weight paper coatings, and other products critical to the responsible utilization of global resources. As industrial minerals become more widely used in ?green? products, mining companies have established best practices for the sustainable management of industrial minerals mining and processing. These management practices include reducing energy consumption, minimizing water usage, increasing waste recovery through recycling and process optimization, and maximizing the amount of ore extracted per acre of disturbed land. With the commitment to SD principles, quantitative methods for objectively measuring SD performance have become increasingly important. Measuring sustainability impact is a valuable tool for effectively applying SD principles and for making choices that balance sustainable development against other business objectives. SUSTAINABLE DEVELOPMENT AND MINING Sustainable development is a term that has become a common part of our lexicon; however, it has multiple meanings and interpretations leading to a sometimes confusing and contradictory array of definitions. The absence of a single, precise definition reflects the fact that SD is a broad concept or paradigm that offers guiding principles as opposed to a specific set of criteria or regulations enforceable by government or other oversight agencies. While a principle based conceptual approach allows businesses to broadly apply SD practices that are tailored to their specific situation, it has also led the public to sometimes view voluntary corporate SD programs with a degree of skepticism (Walker and Howard 2002). This is particularly true in the mining industry. One reason for this skepticism is that the relationship between SD and mining is misunderstood and to many, sustainably developing non-renewable mineral resources is a contradiction (Rajaram et al. 2005). However, this view takes a very narrow interpretation of the tenets of SD. The second is that mining carries a legacy of poor environmental stewardship that does not accurately reflect current corporate environmental practices Many minerals companies have adopted the Brundtland Comission?s definition of SD (United Nations 1987): ?? development that meets the needs of the present without compromising the ability of future generations to meet their own needs?. This definition is very broad and can be interpreted in a number of ways. It provides a general context for sustainable development and is not intended to provide detailed guidelines addressing specific aspects of sustainable development. To fill this gap the following SD principles were drafted by the international minerals community in 2003 (ICMM 2003): 1. Implement and maintain ethical business practices and sound systems of corporate governance. 2. Integrate sustainable development considerations within the corporate decision-making process. 3. Uphold fundamental human rights and respect cultures, customs and values in dealings with employees and others who are affected by our activities. 4. Implement risk management strategies based on valid data and sound science. 5. Seek continual improvement of our health and safety performance. 6. Seek continual improvement of our environmental performance. 7. Contribute to conservation of biodiversity and integrated approaches to land use planning. 8. Facilitate and encourage responsible product design, use, re-use, recycling and disposal of our products. 9. Contribute to the social, economic and institutional development of the communities in which we operate. 10. Implement effective and transparent engagement, communication and independently verified reporting arrangements with our stakeholders. These guidelines insure that SD concepts are applied equally across the industry while setting a clear performance standard and benchmark against which to evaluate success. By adopting these principles and issuing the Milos Statement (http://www.sdimi.org/milos_decl_October%206_2003.pdf), which provides a more detailed vision for integrating SD into everyday business operations, the minerals industry has embraced SD as a core corporate value. The unifying and holistic approach embodied in SD principles impacts the entire mine to market life cycle and addresses the economic, environmental and social consequences of mining. INDUSTRIAL MINERALS The world economy relies heavily on minerals; they are essential to economic prosperity and the quality of life. Industrial minerals are non-metallic, non-fuel minerals that provide the raw materials for a vast range of products used in most every aspect of daily life. They are mined and processed worldwide and they span the spectrum from relatively low value, high volume commodities (e.g. common clay, crushed stone) that are usually mined locally to high value, low volume specialty materials that are sourced from unique one of a kind deposits (e.g. barite, talc, mica). High volume commodity mining operations are often located near the end use market which, in most cases, means areas of high population density where construction and other urban activities drive demand. In these situations the strict adherence to SD principles is particularly critical as these are highly visible operations that must meet the public?s demand for good corporate citizenship. These operations are similar to chemical or other manufacturing facilities that operate near population centers. In contrast, some mining operations are located in remote but environmentally sensitive regions of the globe where the pressure to mine sustainably is driven by the need to preserve habitats and other

Jan 1, 2009

By A. Garassino

A pile design was performed for a thermal power station in Egypt and more than 4000 piles were to be driven. Technical economical reasons suggested the choice of driven composite LACOR piles designed for very high specific loads. Some uncertainties on the behaviour of the pile soil system suggested to perform a test on an instrumented pile. Scope of the test was to verify the possibility of developping the required bearing capacity within the range of the allowable pile settlements values and the effect of the pile joint enlargement on that portion of skin friction to be developped by the upper pile section.

Jan 1, 1991

By Ira Sohn

This article revisits global projections made in 1981of eight metallic and fertilizer minerals for the year 2000. The objectives here are to quantify the differences between the projected and observed levels of consumption for the year 2000 for eight of the 26 nonfuel minerals covered in the earlier study. An attempt is then made to attribute these (often) large differences to the major determinants of minerals demand — income, technological, regulatory and other policy changes, and changes in the recycling rates of the metallic minerals. The eight minerals covered are aluminum, copper, iron, mercury, nickel, phosphate rock, potash and tin. This summary article presents the actual population, gross domestic product (GDP) and per capita GDP changes from 1970 to 2000, compared with the projected rates for these important determinants of mineral use, along with the observed growth rates of minerals consumption for the eight nonfuel minerals included in this study. When the projections are compared with the observed global consumption levels for the year 2000, the differences range from +43 percent for nickel to +229 percent for potash.

Jan 1, 2005

Two of the problems long associated with the complete extraction of level pillars in the wide ore bodies of Broken Hill have been: (1) The high cost of maintaining level gangways through areas of slow subsidence to provide adequate trucking roads for the transport of sand filling; and (2) The difficulty and high cost of completely filling depleted areas. This paper deals with the experiments conducted to devise an apparatus for transporting, with the aid of compressed air, sandfill from the underground sand passes to the stopes and describes the sand blower which has been developed. This apparatus has to a large degree overcome the difficulties and removed much of the hazard associated with the rapid extraction of level pillars.Special attention is drawn to the sizing analysis of the sand and to the fact that it is not dry material. It was early found that these factors were determinants in the design and development of the apparatus described.Acknowledgment is made to the General Manager of Broken Hill South Limited for permission to present this paper, to the engineering department for assisting in the design of the apparatus, and to the underground staff for their co-operation in training the operators and in bringing to success this method of stope filling.PREVIOUS FILLING METHODSThe South Mine, with a monthly production of approximately 32,000 tons of lead-sHver-zinc sulphide ore by cut-and-fill mining methods, requires about 11,000 cubic yards of filling per month. With the exception of a small and variable quantity of developmental mullock, all this filling is...

Jan 1, 1941

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001

It is shown that factors associated with conditions whIch are thermodynamically favourable for the formation of CuS04 in roasting lead to high copper recoveries on leaching. One of these factors is the ratio of the air to solids used for roasting. This can be varied widely without loss of temperature control in the sulphating roasting of many Australian copper concentrates.Thus, the prediction of the air to solids ratio corresponding to a maximum p(SO3) value, for a given concentrate and temperature, is of importance in fluidized bed roasting, since this could be associated with the formation of a maximum quantity of CuS04. Calculations are presented which predict this air to solids ratio, not only for a given concentrate composition, temperature, and pressure, but also for air which is enriched with sulphur dioxide or oxygen.

Jan 1, 1968

By J. P. Sancho, J. M. Duart, J. I. Verdeja, J. O. García

Following a short review of the history of rails used in the transport of passengers and goods, this paper describes the process for rail fabrication, rail structure, and properties, and summarizes the fatigue test curves carried out on rails used today. Also reported is the process for “continuous rail” production using aluminothermic welding via the introduction of weld metal in onsite casting, as a homogeneous melt. Weld characteristics of aluminothermic welding using different preheating procedures—fusion zone, heat-affected zone, microstructure, hardness, slow bend test, and fatigue test resistance (Wöhler curves)—are related to preheating and welding procedures of 700, 900, and 1,100 MPA rail grades. The Locati method is preferred over the staircase method for ascertaining the fatigue limit due to its simplicity. Macrographic and metallographic inspection of broken specimens reveals the reliability of welding techniques and the good metallurgical quality of welds.

Jan 1, 2007

The amount of liquid retained in a porous bed is determined by weighing a column containing the bed.The column is attached to the free end of a cantilevered beam, and changes in weight are determined by calibrated strain gauges (which form a resistance bridge) attached near the fixed cnd of the beam. By coupling the output from the strain gauges to an amplifier and a recorder, a continuous record of changes in the drainage characteristics of the bed may be obtained.

Jan 1, 1968

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009

By Nick Barton

When the Q-system was launched in 1974, the name referred to rock mass classification, with focus on tunnel and cavern support selection. Besides empirical design of support, the Q-value, or its normalized value Qc, has been found to correlate with seismic P-wave velocity, with deformation modulus, and with deformation. The Q-system provides temporary or permanent support for road, rail, and mine roadway tunnels and for caverns for various uses. It also gives relative cost and time for tunnel construction for a complete range of rock qualities. There are also indications that Q has captured important elements of the cohesive and frictional strength of rock masses, with Qc resembling the product of rock mass cohesion and rock mass friction coefficient.

Jan 5, 2007

By N. Arbiter, C. C. Harris

The economic advantages of large diameter ball mills can be compromised by unexpected capacity limiting conditions. These arise because media rotational flow to ore axial flow ratios, and the number of mill revolutions that ore is subjected to during residence, are both inversely proportional to mill diameter. Because of this, mixing efficiency and grinding kinetics may decrease and become capacity limiting when mill diameters reach a critical range. There are two possible scale-up problems involved in the design and use of mineral processing machinery: • Selecting the size and operating conditions for available larger equipment, to insure that operating results will match those obtained with smaller units; or •Extending the size ranges of equipment beyond existing limits. Previous research at Columbia University into flotation machine hydrodynamics has demonstrated the importance in scale-up of internal flow relationships; these perform a similar role in grinding (Arbiter and Harris, 1980).

Jan 1, 1982

The 105th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the J.C. Lemmer Auditorium, SA National Museum of Military History, 22Erlswold Way, Saxonwold, Johannesburg on Thursday, 8thAugust, 2002. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past-presidents, our Members and other guests, among them the following: Mzolisi Diliza, Chief Executive, Chamber of Mines of South Africa Dawie van Wyk and Rod Tucker, Vice-presidents, The Geological Society of South Africa Vaughan Townsend, President, Institute of Certificated Mechanical and Electrical Engineers, South Africa Karel Landman, President, Institute of Mine Surveyors of South Africa Frik Grobbelaar, South African Colliery Managers? Association Pierre Ballot, President, South African Institute of Electrical Engineers Trueman Goba, President, South African Institution of Civil Engineers

Jan 1, 2002

By Christopher Bambridge

The Washington State Department of Transportation (WSDOT) is constructing a new tunneled route under Seattle to replace the existing State Route 99, Alaskan Way Viaduct (AWV), which follows the historic waterfront for several miles. The viaduct separates the businesses that rely upon the tourist trade from the down-town area. The reconnection of the city to the waterfront areas will occur following the completion of the SR99 Re-placement program that replaces the aging structure that was severely impacted by the 2001 Nisqually earthquake, with a state-of-the-art, twin-deck highway with a world record-breaking 17.4-m (57.3-ft) bored tunnel. Constructed in the 1950s, the double-tiered viaduct is nearly 3.2 km (2 miles) long and runs parallel to city?s waterfront. The viaduct, which is partially supported by the seawall, is a vital local and regional transportation link and carries about 110,000 vehicles each day. The seawall, built from concrete and timber in the 1930s, extends along Seattle?s waterfront and supports the soil behind it. Studies in the 1990s showed that the viaduct was nearing the end of its useful life, apparent by its exposed rebar and weakened columns. The 2001 Nisqually earth-quake further damaged the viaduct, forcing WSDOT to temporarily close it for inspection and limited repairs. The viaduct and nearby seawall are vulnerable to an-other earthquake and continue to show signs of age and deterioration. Following a collaborative process, WSDOT developed the following guiding principles to the viaduct replace-ment:

Sep 1, 2013

By Fennell B

A process for the recovery of cobalt from a speiss produced at Sulphide Corporation is presented. The speiss is leached in oxygenated sulphuric acid to dissolve the metallic iron at a pH of around 4. The resultant iron (11) is subsequently oxidized in the leaching vessel and precipitates as goethite. Acid is regenerated in the precipitation allowing dissolution of further speiss. Subsequent to the conversion of most of the iron in the speiss to goethite, conditions become sufficiently oxidizing to dissolve cobalt. Cobalt is not co-precipitated under the leaching conditions, yielding a pregnant solution containing the cobalt and some iron (11). The principal advantage of such a process is the significantly lower acid consumption over that obtained by complete dissolution followed by selective precipitation. An impure product of cobalt hydroxide can be obtained from the pregnant solution by neutralization.

Jan 1, 1983

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003