Search Documents

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By Mike Muchard

Augered cast-in-place piles are one of the most cost effective deep foundation options available to designers but have been largely underutilized due to skepticism associated with quality assurance and hence capacity. When installed correctly, unit friction values can rival any other competing foundation system. To this end, many means have been implemented to increase confidence in the competence of the foundation. One such method is load testing via the Statnamic test method. This paper presents an overview of the Statnamic test method, advantages and disadvantages of its use, and several case studies where Statnamic testing of augered cast-in-place piles confirmed quality construction, brought about design changes, or proof tested problematic installations.

Jan 1, 2000

By K. Oraee

Zarshuran gold deposit, with the total reserves of some 12.5 million tons of 4.18 g/ton ore, is considered to be an important gold mining project in the area. In this paper the feasibility studies of the whole project is carried out on the basis of several economic variables. Given that mining data are often of uncertain nature, these economic variables have therefore been estimated under the conditions of uncertainty. The resultant Net Present Value is hence also obtained under the same conditions. For this purpose, a model is first devised with the help of Excel and COMFAR software. The model is then developed that considers different scenarios which would result in different expected values for the economic variables. It is concluded that the NPV of the project is most sensitive to gold and silver price and that other variables such as discount rate, operating and capital cost all affect the feasibility of the project with lower degree of severity. Finally, risk analysis is also carried out using Mont Carlo technique, in order to estimate the most probable value of NPV. The average NPV calculated in this way is US$ 49.7 Million, whilst without due consideration of risk, this would be US$ 36.6 Million. The techniques used, together with the procedures adopted in this paper, can be used in feasibility studies of all mining projects. Such decision would result in more accurate Net Present Values than expected from other frequently used methods.

Jan 1, 2011

By A. P. I. Popoola

Laser coatings are used for a wide variety of applications. TiB2/Ni intermetallic matrix composite coatings were fabricated on Al-substrate by a high power Rofin Sinar Nd: YAG solid-state laser. The characterization of the coatings was carried out by optical microscopy (OM), scanning electron microscopy (SEM/EDS) and X-ray Diffraction (XRD). Electrochemical study of the laser coatings in 3.65 per cent NaCl at room temperature revealed that with very high weight proportion of nickel the corrosion resistance of the coatings deteriorated due the presence of AlB10 phase. 50 wt per cent TiB2+50 wt per cent Ni laser coatings exhibited the highest corrosion resistance in test solution. Keywords Corrosion, protective film, laser surface alloying, reinforcement.

Jan 1, 2011

By Rick Frechette, Bryan Ulrich

Representatives from several mining operations in three western states left their mines behind for a day in February to discuss with their peers the issue of water. The event was Knight Piésold and Co.’s Roundtable 2007, held in Elko, NV. It was third such event put on by the company. The issue this year was site-wide water considerations.

Jan 1, 2007

By Alastair Grogan, Ron Elliott, Dale MacLean

Blasting for armour stone presents many unique challenges. Often, blasters get themselves into trouble when they assume that they can simply modify a production blast design to produce the required fragmentation size. They bid on the project using typical production blasting costs, and then find that they cannot produce the required fragmentation size and quantity with an acceptable waste factor. This paper outlines industry best practice guidelines for the production of riprap or armour stone. The paper examines the importance of initial geological mapping to determine the average in-situ block size, and the advantages to be gained from working with the geology to maximize production of the required block sizes. The paper also outlines the importance of proper explosives selection as well as blast designs that are unique to the production of riprap. The paper reviews challenges and experiences realized from multiple projects in differing rock types.

By C. K. Kocsis, S. Hardcastle

Mine ventilation, requires electricity to operate the fans and fossil fuel for heating. Typically, this accounts for approximately 40% of the overall underground energy consumption. This is considerable, and one of the major causes of this expense is that most mine ventilation systems are designed for the "worst-case-scenario" with respect to ventilation demand, which is commonly dictated by diesel equipment usage. Once designed, mines tend to operate their ventilation system at this peak level despite their exceeding day-to-day development and production needs due to lack of appropriate ventilation controls. In underground metal mines, TeleminingTM, which includes the tele-remote operation of mobile development and production equipment from surface, will change the mine design criteria including its support infrastructure such as the ventilation system. With the removal of machine operators to surface control rooms, conventional ventilation systems designed to dilute and remove pollutants can become redundant. Depending on the ultimate need for ventilation, its cost in automated mines with tele-remote equipment operated from surface will be lower than the cost of ventilation in conventional mines. These cost savings, which could be significant, would not only come from the ability to reduce the amount of ventilation in the mine, but also through the capacity to automate its distribution. This paper provides an indication of the new airflow requirements in stopes and dead-end developments for the tele-remote and automated mining processes based on climatic modelling. Furthermore, this paper makes a cost benefit analysis by comparing the ventilation system operating cost of a conventional underground metal mine based on the mobile diesel powered equipment design criteria with the newly redesigned ventilation system operating cost of an automated mine based on the "heat management" design criteria.

Jan 1, 2002

By T. R. Raponi

"The Williams Mine, Canada's largest gold mine, processes over 6,000 t/d of ore utilizing SAG/ball milling, leaching and CIP, carbon stripping, electrowinning and refining to produce gold dare bullion.Grinding accounts for over 50% of milling costs with grinding media, power and mill liners making up over 75% of grinding costs. Since 1991, several changes in these areas have been made which have significantly reduced costs, while fineness of grind and mill recovery have both been increased.This paper discusses the changes made in the grinding circuit over the past few years and assesses their impact on operating costs and mill operations.IntroductionThe Williams Mine is located in the Hemlo area of northwestern Ontario, about 40 km east of Marathon. It is operated by the Williams Operation Corporation, which is equally owned by Teck Corp. and Homestake Canada Inc. Canada's largest gold mine, the Williams Mine commenced operation in October 1985 at a rate of 3, 000 t/d. Mill throughputs have typically exceeded design, averaging 3, 397 t/d in 1986, and 3,380 t/d in 1987. In August 1988, production was increased to 6,000 t/d. Throughput averaged 4,212 t/d in 1988. Production increased over the next few years averaging 5,477 t/d in 1989, 6,248 t/d in 1990, 5,987 t/d in 1991, and 6,283 t/d in 1992. With a recovery of over 95.5%, production for the first three quarters in 1993 is averaging 6,408 t/d.GeologyThe main ore body is a steeply dipping conformable zone of microcline-quartz-muscovite rock. It occupies the contact zone between hanging wall metasedimentary rocks and foot wall felsic quartz feldspar porpyritic rocks of possible volcanic or subvolcanic intrusive origin. The ore body is enveloped by muscovite schists which are thickest on the footwall side. The schist is enriched with tourmaline, pyrite, and green mica containing vanadium and barium. The ore body contains pyrite and barite which occurs mostly in laminae and bands to veinlets and breccia fillings. The gold occurs as free (native) grains, 20 to 30 µm in size at grain junctions of the microcline and quartz. Visible gold is rare in the main zone. There are commonly two or more discernable layers of economic value which are separated by weakly gold mineralized material which usually consists of muscovite schist, barite rich zones or sulphide poor-microcline-quartz rock and in the upper and western fringes by biotite rich schist with feldspathic fragmental characteristics. Molybdenite is a common constituent as very fine disseminated grains in the microcline-quartz rock and is most prominent with gold enrichment. Stibnite and realgar are two of the more common accessory sulphides."

Jan 1, 1994

By D. M. Weinberg, S. R. Novascone, R. R. Reynolds, J. H. Cole, C. D. Christensen

The mechanical properties of the rocks surrounding an orbital vibrator alter the shape and amplitude of the vibrator’s orbit. Detecting these changes with driving point impedance measurements promises to reveal fractures and, possibly, identify the in situ stress state and significantly increase the depth that can be investigated. Our research emphasis has been on detecting vertical fractures through casing. Experimental and numerical results to date indicate that our new logging tool has excellent potential for determining both the vertical extent and azimuthal orientation of such fractures. Fracture and in situ stress orientations are useful in mine planning.

Jan 1, 2002

By Steven J. Page, Wm. Randolph “Randy” Reed, John A. Organiscak

Researchers studying dust generation from blasthole drills developed a simple, quick fix that reduced respirable dust concentrations by more than 63% at the dump point. This device, which requires almost no maintenance, is small and inexpensive, and it will help operators maintain compliance to the dust standard. The thought process was that a reduction of respirable dust at any of the multiple sources on the drill, in this case the dust collector dump point, should reduce the total respirable dust generated by the drill. The U.S. Mine Safety & Health Administration (MSHA) has a coal respirable dust standard of 2 milligrams per cubic meter (mg/m3) for an 8-hour shift. MSHA and mine operators periodically collect personal dust samples to determine compliance with this dust standard. Drill operators have one of the highest exposure levels to respirable dust. This has been proven through many reviews of the MSHA dust sampling database. Prior to 1987, the highwall driller at surface coal mines had the most severe exposure to respirable silica dust, a trend that continues today based on MSHA's respirable dust sampling database. A review of the MSHA database for the years 1985 through 1992 shows that 81% of the respirable silica dust samples taken exceeded the permissible exposure limit for the highwall drill operator at surface coal mines. A more recent review of the MSHA database, for the years 1996 through 2000, shows that only 31% of the respirable silica dust samples taken exceeded the respirable silica dust limit for the highwall driller at surface coal mines. This suggests a substantial improvement in preventing the exposure of silica dust to the highwall drill operator. The drill operator, however, still tops the list of job occupations that have the highest exposure to respirable silica dust Respirable dust has been shown to be harmful to human health, especially when silica is present in the dust. It causes a disease known as silicosis, which can occur in three levels: chronic silicosis, which occurs after 10 years of exposure; accelerated silicosis, which occurs between 5 and 10 years of exposure; and acute silicosis, which can occur within a few weeks to five years of very high exposure to silica dust. Respirable dust consists of the dust particle size fraction whose median diameter is 4 micrometers (µm). The drilling machine generates high concentrations of respirable dust from several sources: drill table shroud leakage, dust leakage through the table bushing, dust discharge from the dust collector exhaust due to impaired filters, and dust entrained from the dust collector fines dumped onto the bench. The National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Lab (PRL) has been studying different methods to reduce respirable dust from these sources. During its testing, the institute identified a simple solution that reduces the amount of respirable dust generated at the collector dump point.

By Pat McCarran

WHEN this Government was founded, the framers of the Constitution wrote into that instrument a provision that Congress should "coin money and fix the value thereof;" and the Constitution prohibits making anything but "gold and silver" lawful money. So silver is written into our basic law. Shortly after President Washington took office in 1789 the Congress passed the first Mint Act, setting up the U. S. Mint. In that Act, signed by President Washington on April 2, 1792, the weight of the American dollar was fixed, and it was provided how much silver should be contained in a silver dollar and how much gold should be contained in a gold dollar. It was decided that 371 1/4 grains of pure silver was to be the standard dollar of America. That standard with respect to the pure silver content of the dollar has never changed.

Jan 1, 1947

By R. N. Gow

The presence of enargite (Cu3AsS4) is problematic in gold processing because it is environmentally hazardous due to its arsenic content but also because it is double refractory causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte, Montana and Quiruvilca, Peru were spectroelectrochemically studied under alkaline conditions, pH range of 8-13, using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after voltammograms were potentially cycled in order to determine and compare surface species against theoretical EH-pH diagrams determined from mass-balanced thermodynamic calculations using StabCal software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of sulfur suggests that copper was eventually leached. By operating above pH 12, under slightly reducing conditions near -300mV vs SHE, arsenic can be selectively leached as thioarsenate (AsS43-) or thiosulfate (AsO43-) without sulfur formation.

Feb 27, 2013

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By Cherie H. Tilley

The possibility of drilling oil wells from underground locations is not a new concept. It bas not been cost effective for the oil industry in the past and therefore disregarded. Today's state of the art in tunneling and shaft sinking greatly improves the potential for this type of oil field development scheme. This report presents a plan for providing a aeries of drilling bases and the design of the drilling location. The design minimizes the amount of excavation needed to develop the oil field and maximizes the use of rapid excavation techniques.

Jan 1, 1983

By Robert Martin, Brian W. Stump, David P. Anderson

2We use field measurements to quantify physical processes that accompany different types of mining explosions. The data sets collected include three-component ground motion, acoustic, video and high speed film, three dimensional topography, geological and geophysical properties, design blast pattern and timing, and velocity of detonation in the explosive for individual borehole detonation times. The explosions include simple single-fired contained explosions, ones designed to bulk and fracture material and those that cast material. Our goal is a physical understanding of these sources for the purposes of optimizing blasting practices.

Jan 1, 1998

By Thomas C. Shapiro

This is the second in a series of articles on microcomputers and applications in the minerals industry. The first article (ME, Feb., page 129) discussed microcomputer terms and concepts. This article will discuss software for geology and mining. The third article will cover plant, administrative, and geotechnical software applications. Introduction Geology and exploration are areas where computers have a natural fit. Large volumes of data need to be tabulated, evaluated, and made into maps and reports that allow geologists and management to make a decision on a project or mine. Until recently, the programs that performed these tasks were cumbersome and not user friendly by any stretch of the imagination. Learning time to become an expert in these programs typically would be six months or more. The computers needed to run these programs are expensive mainframes. Several years ago, the use of minicomputers became popular because of their lower cost. Programs were adapted to fit these smaller machines and became friendlier. With the advent of micros, many programs. were rewritten and used the screen capability more effectively, thus providing a real advance in user interface. Programs and Price The definition of micro, mini, and mainframe is becoming blurred. For the purposes of this article, micro refers to either an eight- or 16-bit computer, costing less than $10,000 and, more typically, under $5,000. Mini refers to a 16- or 32-bit computer that typically costs more than $25,000. Mainframe refers to a 32-bit or larger computer that costs more than $250,000. There is a large gray area between micros and minis, and minis and mainframes. Technology and prices are changing so fast that the traditional definitions have become almost meaningless and price has become a better guide. With the arrival of the minicomputer, costs for hardware began to fall, but the programs have tended to remain unfriendly. In some cases, the minicomputer acted as a front end to the mainframe. Cost of both the programs and minicomputers could easily run a minimum of $70,000. A total cost of $200,000 would not have been out of line. The average geologist and company would have a great deal of difficulty justifying such a purchase. The advent of the microcomputer has changed all that. For $3,500 to $5,000, one can buy a 16-bit micro and a printer. Plotters with six pens are available for $2,000 that will produce a 280- x 430-mm (11- x17-in.) map. For several hundred dollars, software is available to act as a word processor, an economic spread sheet, or to perform ground water calculations. In fact, some programs are available for free. Some of these programs are relatively easy to learn. In addition, programs are being developed daily that are easy to use. More importantly, large programs that once ran only on mainframes are being converted

Jan 3, 1984

By J. C. Poulos

The West Elk Mine is located near Somerset, Colorado approximately 70 miles southeast of Grand Junction, Colorado and 72 miles southwest of Glenwood Springs, Colorado on state highway 133 (Figure 1). The West Elk Mine was opened January 20, 1982 as the Mount Gunnison #1 Mine operated by the West Elk Coal Company, a division of ARCO Coal. In the early 1990?s ARCO changed the mine name to West Elk Mine and the operating company was renamed Mountain Coal Company. Arch Coal, Inc. purchased the West Elk Mine in 1998. West Elk Mine has produced coal from three different seams. Coal was first mined from the F Seam, the upper most seam in the stratigraphic sequence, from 1982 through 1991. Coal was produced from the B Seam, the lower most seam, starting with continuous miners in 1991 and transitioning to longwall mining in 1992and continued on through October 2008. The development of the E Seam, which is the middle seam in the stratigraphic column, started in 2004 with longwall production commencing in 2008. The ventilation conversion from exhausting to forcing for the E Seam portion of the West Elk Mine was implemented in late October 2009.

Feb 27, 2013

By Brendan Henry

The Canada Line is a 19km long automated light rapid transit system with 16 stations in Vancouver, BC, Canada. The Concession was awarded to InTransitBC to design, build, partially finance, operate, and maintain the system for 35 years. The project must be complete by November 2009 to be ready for the 2010 Winter Olympics to be held in Vancouver and Whistler, BC. The bored tunnel section consists of 2.45 km of twin bored tunnel and 3 stations. The station work is limited to the excavations and temporary support necessary to facilitate the bored tunnel works. A joint venture between SNC-Lavalin Constructors Pacific and SELI (SSJV) has recently completed the design and construction of this section. Work for the bored tunnel commenced in November 2005 with shoring and excavation works for the tunnelling operations pit that will become Olympic Village Station and will be completed in the spring of 2008. The tunnels were driven with a 6m diameter Earth Pressure Balance Tunnel Boring Machine (EPBM) and lined with 250mm thick, 5.3m diameter precast concrete segments. Seven hundred and fifty meters of each tunnel were driven through glacial and interglacial deposits of sand, silt, and clay with granitic boulders. The paper discusses the challenges faced in negotiating these soils which contained unforeseen geological conditions. These conditions were overcome by developing a systematic approach to Risk Management that included thorough risk assessments, regular risk management meetings with the participation of two of the world?s leading EPBM experts, Professor Eisenstein and Professor Kovári, and by the ability of the construction team to effectively analyze and mitigate problems.

Jan 1, 2008

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009