Search Documents

By Wm. Mark Hart

High horizontal stresses and shear failure have been considered the major reasons that cause entry roof failure and falls for underground mining. Therefore, reorientation of the current mining systems or layouts or using angular crosscuts in mains or gate entries becomes more popular if a greater than normal horizontal stress is measured. However, reorientation of the current mining systems or layouts is always expensive and use of the angular crosscuts may weaken the pillar structure at corners. Therefore, cautions must be taken before any decision related to reorientation of the current mining systems or layouts or use of angular crosscuts is going to be made. In order to prevent entry roof failure and falls, the following two issues must be carefully examined and fully understood: 1. Which one, shear stress or tensile stress, is going to be blamed for entry roof failure? 2. Which one, horizontal stress, vertical stress, or local geological weakness plays a major role in entry roof failure and falls? This paper analyzes the mechanisms of entry roof failure and falls for underground mining in general examines the roof fall history at Springvale Colliery, and proposes the means of preventing roof failure and controlling roof falls for Spingvale Colliery in particular.

Jan 1, 1996

By D. Yu. Paleev, O. Yu. Lukashov, A. Yu. Krainov, E. R. Shrager, I. M. Vasenin

The gas-dynamic method is presented of calculation of explosion-proof distances during an explosion of the methane-air mixture in mine working. On the basis of this method is modelled of shock waves interaction with explosion protective parachute partitions, obstructions and water barriers. Calculations have been carried out of attenuation factors of shock waves during their interaction with explosion protective structures, arranged near conjugation zones of mine workings. Possibilities have been analysed of suppression of intensity of shock waves and of propagation of shock waves control in mine working network of coal mines by installation of explosion protective structures.

Jan 1, 2003

By Fred N. Kissell

In This Chapter [Ventilation and methane sampling guidelines for conventional shafts Dealing with restricted spaces where methane can accumulate Ventilation and methane sampling at raise bore drills and Filling shafts at closed coal mines] It is not unusual to encounter methane gas during shaft excavation or shaft-filling operations. Shafts into coalbeds usually produce the most methane, so the information in this chapter applies primarily to shafts at coal mines. Nevertheless, much of the information is relevant for noncoal mines that have methane in the mine or in the overlying strata. METHANE IN SHAFTS EXCAVATED BY CONVENTIONAL MEANS (DRILL, BLAST, MUCK) [ ] Ventilation. Shafts excavated by conventional means are ventilated with a fan on the surface connected to ductwork that extends down into the shaft (Figure 9–1). Shafts into coalbeds should have ventilation systems designed to handle the higher gas flows to be expected as the shaft excavation passes through any over-lying gas-containing strata and nears the coal-bed to be mined. Following are some simple ventilation guidelines for the minimum amount of air required and the selection of the ventilation duct: • Provide enough air to meet the mini-mum OSHA tunnel requirement of 30 ft/min air velocity in the open shaft, as specified in 29 CFR2 1926.800(k)(3). For example, a 20-ft-diam shaft having

Jan 6, 2006

By K. Boakye

This paper presents the results of a review of historic blast design practices at the Dragon Products Company, LLC (Dragon) Quarry Operation, along with the results of two different blast design vibration monitoring programs. A blast pattern design modification was initiated to determine if production volume per shot could be increased and highwall instability could be decreased. A vibration monitoring program was undertaken to investigate peak particle velocity (PPV) and relate the data to the blastability of the jointed onsite rock mass, utilizing the relationship between PPV and dynamic stress and strain. The Dragon Quarry Operation has historically used a 6-in. diameter, 14-ft by 14-ft production blast pattern, with blast holes loaded manually using cartridge style explosive products. In 2011, Quarry Operations introduced a 6-in diameter, 16-ft by 16-ft production blasting pattern, using pre-mixed, truck-loaded, bulk emulsion/ammonium nitrate/fuel oil (ANFO) blends. This paper summarizes the results of the blast design modifications, the results of the vibration monitoring data, and describes how production blasting and excavation at the Dragon Quarry has benefited from such modifications.

Feb 27, 2013

By Donald Leroux, Simon Gariépy, Luc Lachance

"Quantitative information about the quality of metal balance results is often overlooked when making important plant production planning decisions. Not only is this common omission made in a context where many measurements taken in and around mineral processing plants carry significant errors, but it also conflicts with the AMIRA P754 Code of Practice for Metal Accounting. The fact that metal balances are typically published without any indication of data quality may give the wrong impression that the measurements are unquestionably accurate. While it is true that statistical data reconciliation can improve the confidence intervals of redundant variables, there is no data processing technique that brings them down to zero at a finite cost. In this paper, we review the entire data flow, starting from field instruments to metal accounting-based decision-making to show how measurement errors are transmuted into business risks associated with production planning. Necessary conditions for first exposing then quantifying such business risks are stated. Pitfalls to be avoided are also discussed. Finally, a simplified risk assessment and management procedure which considers the quality of metal balance results are applied to a polymetallic mineral processing plant. INTRODUCTION Each and every mineral processing plant has production reporting obligations. In this paper, we are concerned with metal accounting reports (Morrison, 2008) where saleable metal flows and inventories are estimated and published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimisation, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that spotless metal accounting is instrumental to high-quality corporate governance (Gaylard et al., 2014) of mining and metallurgical companies. To this extent, one would have expected industry-endorsed standards to have emerged a long time ago. However, the lack of an accepted set of standard procedures for metallurgical accounting was explicitly recognized as an industry-wide problem only in August 2001 during an SAIMM workshop held in Cape Town, South Africa. Discussions that followed this workshop led to the initiation of the AMIRA Project P754, “Metal Accounting and Reconciliation”, in 2003."

Jan 1, 2015

By Fred W. Brackebusch

"The use of paste technology for surface tailings disposal may offer economic, technical, safety, and environmental advantages for both underground and surface mining operations. Paste is a non-Newtonian fluid having some shear strength during transport and placement. The strength is augmented after placement by consolidation, water loss, and by addition of chemicals. Economical dewatering systems are necessary to the success of surface paste tailings disposal. In an underground mine, the paste backfill plant can produce paste for surface disposal about 50% of the time because only about 1/2 of the tailings are needed for backfill. The distribution of paste to the surface stack involves expensive pumping equipment and thus a nearby location of the stack is desirable. The viscosity of paste can often be manipulated by modifying pH. Placement of the paste in a designed stack configuration depends on topographic and climatic factors as well as paste properties.INTRODUCTIONThe use of paste technology for mine backfill is becoming accepted for underground mines mainly because of ground control and economic reasons. Paste technology is just starting to be applied for tailings disposal with only a few hardrock metal mines worldwide using the technology; however, it has been used extensively for red mud disposal in the aluminum industry. The disposal of dry tailings is very attractive from environmental and safety points of view because of limited water which might potentially escape and pollute river systems. Dry stacking systems, however, are expensive because of filtration and truck transportation costs. Paste can be produced from most tailings streams by special types of thickeners. Furthermore, it can be transported in pipelines, therefore paste technology may be more economic than dry stacking but still have some of the major advantages. Understanding of paste technology has improved through experience with operating underground backfill systems in recent years and because of testwork and research programs by mining companies, consultants and equipment vendors. Thus we may be on the verge of taking a new look at tailings management using paste technology."

Jan 1, 2002

By Joanna LaForte

"In response to “Arctic Mineral Wealth —Equitable Participation with Aboriginal Landowners – A slow or fast process?”, this author’s impression is one that, to her, seems obvious — this is definitely going to be a slow process. To question this issue seems ridiculous, unless the mining industry is considering following the same patters of the past, thereby adding to the suppression and injustices to which the aboriginals are so accustomed. To make genuine progress, where trust and good communication has been achieved with time as a factor in proceeding, the author feels, without a doubt, that the triangle of industry, government and aboriginals will seriously have to be restructured or eliminated. Anytime you mix government with progress, along with other problems, you are looking at bureaucracy, and that takes time. Issues such as the settlement of land claims have not been resolved, and in all likelihood could take forty years to finalize. Aboriginals have been suppressed for centuries by governments and industries with ethnocentric ideologies, and now that they are in a position to reclaim their lands, attain their own economies and government, and truly secure a wealthy, self-sufficient legacy for their descendants, how can anyone imagine they’ll move quickly? This author also strongly disagrees to some sections of Mr. Wakefeld’s article and will expand on her objections.We question whether aboriginals under-stand the process of mine development. If we encounter an electrical problem in our home, o we not call an electrician without having to learn the trade ourselves? This comparison seems simplistic, but does convey a point. As cited, “there are now over 100 000 aboriginals who have completed post-secondary education.” Are the numbers revealed in Mr. Wakefeld’s paper there to scare us? Is he suggesting that without the industry’s haste, the aboriginal’s new found intelligence could pose a problem to the mineral explorer. While it is true that not all are highly educated, the aboriginals have specialists in market fluctuations, feasibility studies and the needed skills. They have specialists, such as their representative organization of COPE 1984, (the Committee for Original People’s Entitlement), who under-stand their cultures, language and desires. Their education should expedite the negotiations and end the power struggles equitably. Aboriginal people are not stupid. Once they have reason to be proud, regain their communities and know the direction that they’re headed, their self-determination will return."

Jan 1, 1996

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By R. C. Burtan

Long before recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It is well known that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica-containing material have a great many uses in modern society. This material, however, is potentially an extreme health hazard. Silicosis: Not a New Disease Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. He was obviously describing silicosis. It is also apparent from ancient writings that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. Silicosis was certainly described by Agricola in his De Re Metallica published in 1556. Here he described lung disease among hard-rock miners. The original document was written in Latin and then translated in 1912 by Hoover and Hoover. One of these translators was Herbert L. Hoover, a former US president who once made his living as a mining engineer. More recently, there are numerous references in medical literature in the 19th and 20th centuries relating silica exposure to silicosis. There are specific references to mining in hard rock, as well as to sandblasting and a host of other industrial exposures. In 1919, Winslow described standards for measuring the efficiency of exhaust systems in polishing shops using sandblasting. These standards were equally applicable in the mining industry. As early as 1920, Winslow explored the efficiency of certain devices used to protect sand-blasters against the dust hazard. These devices were equally applicable in the hard-rock mining industry. The medical community recognized the silica health hazard in the early 1900s. Middleton described the illness in the British Medical Journal in 1929. He noted the danger to health at that time. D. Hunter mentions in his book, The Diseases of Occupations (1969), the monumental work of Merryweather in 1936, in which he surveyed the silicosis risk in Great Britain. He showed statistically that the average employment length of sandblasters who ultimately died of silicosis was 10.3 years, compared to 40.1 years for all fatal cases, irrespective of occupation. Sandblasting and hard-rock mining and drilling, obviously, are very hazardous occupations. Weil and Zisking of Tulane University wrote in 1975 that "it was known as early as 1935 that the course of silicosis is much more rapid in sandblasters than in miners or foundry workers. This can be explained by the fact that sandblasters are exposed to an almost pure siliceous dust containing high concentrations of respirable particles within the range of 1 to 3 micron size." Protecting the Worker The medical community recognized in the early 1900s the need for proper protective equipment for all of those who worked with siliceous materials. Middleton, writing in 1929, said: "The worker is then protected by a close fitting helmet with an air feed, much as in the case of an underwater diver. In spite of these precautions, cases of silicosis among sandblasters are being met with today. It is a matter for serious consideration whether a substitute, such as steel or iron grit, could not be used to replace the siliceous grit as the abrading material." C. E. A. Winslow, a professor of public health at Yale School of Medicine, and others wrote of the need to protect sandblasters by

Jan 7, 1984

By Carlos Soria

El presente texto describe los Sistemas de Gerencia de la Información y su aplicación en la industria minera con el objetivo de optimizar la gestión total de la empresa. Dichos sistemas manejan información del proceso y sus valores de producción, cálculos, consumos de energia, emisiones de plantas, tiempos de funcionamiento de equipos, eventos, alarmas, mediciones de laboratorio y control estadístico, etc. De forma que dicha información pueda ser reunida y consolidada, convirtiéndose en materia de significado y relevancia disponible en base a análisis, reportes, listas, tendencias y gráficos para que el usuario final de una planta o en sus oficina pueda tomar mejores decisiones.

Jul 17, 2000

By Gerald Whittle

What is Enterprise Optimization? Releasing value through better planning decisions: Philosophy, Methodology, Software The key to 5% -35% increase in enterprise value (NPV) The culmination of 25 years development in optimization for the mining industry ?Jeff Whittle Simultaneously optimizing: ?all steps in the value chain ?all assets in the enterprise portfolio ?all periods together

May 1, 2010

By Kerry Lahti, Bryan Ulrich

On Feb. 11, 2005, more than 20 mining professionals gathered in Elko, NV for a day-long round-table discussion on heap leaching. Attendees included project managers, operators and environmental professionals. They represented 10 mining organizations. Knight Piésold sponsored the special event. Its seven representatives included three staff members from the company’s Elko Operation, and one each from its Denver, Cajamarca (Peru) and Vancouver offices. The roundtable format was chosen to allow people from the mining industry to share ideas and experiences in an open forum. Rather than presenting prepared talks, spontaneity was encouraged. This resulted in a lively and enjoyable discussion.

Jan 1, 2005

How the Australasian and Canadian Codes (VALMIN and CIMVal) approach mineral property valuation is described. Brief comment is also made on the International Valuation Standards CommitteeÆs interest in a global valuation standard for Mineral (Extractive) Industries and the South African SAMREC initiatives to adopt a VALMIN-like Code. The conventional tripartite classification of valuation approaches into those that are Market-based, Income-based and Cost-based is outlined. It is best practice to use as many of these approaches as possible (and as many methods as reasonable in the particular circumstances), given the quantity and quality of the data available on the Mineral Asset (which depends upon the state of development of the mineral property). The use of specific methods must satisfy the basic considerations of logic and reasonableness and the purpose of the valuation. The competence, judgement and repute of the valuer are critical factors, since all valuations are time and circumstance specific. What constitutes æMarket ValueÆ in the different jurisdictions is discussed and definitions are given. Challenges facing the globalisation of a VALMIN-type Code for the international Minerals Industry are the influence of real estate valuers and the US jurisdictional idiosyncrasies. This is mainly due to a fixation on real property rights with a preference for using real estate-like comparative sales techniques (Market Approach) to the exclusion of Income-based approaches; a regulatory reluctance in the US to accept that Resources have considerable value; and the International Accounting Standards BoardÆs preference for Historical, rather than Current Value, accounting.

Jan 1, 2002

Good morning and thanks for the chance to talk to you. It's really pleasing to see so many industry representatives here I want to spend a few minutes talking about issues relating to your industry. At the end of today I would like to leave you with three strong messages from government. The first is that this government supports environmentally responsible mining and the endeavours of the mining industry. The second is that explorers and developers are wanted and welcomed in New Zealand. And the last is that it is up to the industry to keep the public properly informed about how your industry and to constantly work on improving your public image. The mining industry is a high-tech industry which fits snugly with our concept of a growing knowledge-based economy. It has particular value for regional development, the gold mining industry alone provides more than 4,000 jobs û mostly outside of the main cities. The industrial minerals industry is twice as large as that. As well as those people directly employed by the industry there are greater downstream effects for the community. One example from the broader extraction industry of this is of the local pie shop down the road from one of Taranaki's petroleum industry locations. The shop sells over $4,000 worth of pies a week to workers in the industry. That's just one example of the positive benefits the industry brings to its local community and is the sort of real positive benefit you need to be telling people about  

Jan 1, 2000

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

By V. C. Kelessidis

The interaction between rock and drill bit during drilling has been modeled for many years, but a complete understanding of the phenomena occurring has yet to materialize. Successful models will allow the prediction of rate of penetration in a given environment and optimal selection of drill bit and drilling parameters, thus minimizing exploration costs. In most rock-drilling models the value of the unconfined compressive strength of the rock (UCS) is used in the predictive equations, within the concept of specific energy, and the value of UCS is the percentage of the value of the stress applied on the drilling bit in order for the bit to advance. While the exact percentage depends on the model used and it is not known with certainty, good knowledge of UCS is nevertheless required before any decent prediction can be made on rate of penetration. Determination of UCS, normally done via destructive testing, requires not only the availability of sound rock core samples but also expensive testing and significant time for the test, which frequently are not available for routine drillability predictions. Hence, a multitude of methods and techniques has been proposed for estimating UCS from various indirect and/or non-destructive measurements, or combination of measurements with neural networks, such as point load index, block punch index, unit weight, and apparent porosity, water absorption by weight, sonic velocity, and Schmidt hardness. The many proposed approaches are critically reviewed and the results are compared, and what becomes apparent is that after many years, not only in mining but also in oil-well drilling, accurate indirect determination of UCS is still an elusive goal. An equation to predict UCS from sonic velocity data is suggested based on several data sets reported in the literature. Use of the specific energy equation with UCS or sonic data and utilization of drilling data allows an estimation of the efficiency of energy transfer from the bit to the rock and of the friction coefficient. Analysis of data reported in the literature, both from laboratory and field studies, has shown that this approach is sound and enables the determination of energy transfer efficiencies and friction coefficients, which for the cases studied range between 15 and 30% and 0.15 and 0.30 respectively. Thus, the suggested data analysis approach allows drillers to focus on inefficiencies and optimize drilling practices in future campaigns. Keywords Rock drillability, unconfined compressive strength, prediction.

Jan 1, 2011

By Frank Callanan

The Ameristar Casino expansion project included the design and construction of a 25-story hotel and 9-story parking structure expansion. The site is located in a floodplain on the banks of the Missouri River in Saint Charles, Missouri, where the underlying soils are potentially liquefiable. The geotechnical engineer performed subsurface exploration and analysis, which included site-specific seismic response and liquefaction, and provided geotechnical design recommendations. In the event of an earthquake, post-liquefaction settlement was calculated to be approximately 14 inches. Additional project constraints included wetlands protection, construction adjacent to the existing facility, flood protection and river bank stability. Because of the liquefaction issue, the geotechnical engineer consulted with a specialty geotechnical contractor on ground improvement methods. This consultation led to a proposal to eliminate deep foundations from the design and support the structures on shallow and mat foundations. The geotechnical engineer assisted the design team with foundation design analysis and value engineering assessments. Together with the project team, the geotechnical engineer used the data to evaluate foundation options and construction methods to overcome the site challenges and concluded that ground improvement was the optimum course of action. Because of the nature of the site constraints, a number of ground improvement methods were needed. The geotechnical engineer evaluated the methods proposed by the geotechnical contractor and provided the technical specifications for the ground improvement bid package, which included vibro-compaction, compaction grouting and micropiles. The ground improvement allowed for the use of shallow foundations (mat and spread footings), which provided the client with significant time and cost savings over the deep foundation alternatives.

Jan 1, 2009

By A N. Kasnanto, D A. Sims, J Pocoe, B Pulungan

In this case study we compare the sampling quality of diamond drilling (DD) and reverse circulation (RC) drilling at the high sulfidation Purnama gold–silver (Au-Ag) deposit located in northern Sumatra, Indonesia.There was a systematic bias of 23 per cent gold metal under-call in the diamond drilling based Ore Reserve estimate compared to the mill reconciliation over three years of production. The RC based Grade Control data and mill production data were in much closer accord. Investigation led to quantification of the significantly reduced sampling imprecision (or improved precision) of RC drilling samples relative to diamond drilling samples and the determination of a grade bias between the drill types caused by sample volume and metal distribution in the mineralisation. An infill RC drilling program was undertaken to improve data density across the pit for inclusion in the Mineral Resource estimate. This subsequently increased Au metal in the estimate by 16 per cent.The sampling imprecision of primary diamond drill sampling is rarely tested. Duplicate sampling can be used to quantify sampling imprecision at each stage of subsampling. In diamond drilling it is tested at the primary sampling stage via second half core sampling, while RC sampling is tested with field duplicate sampling at the rig. Duplicate data can be compared in a number of ways to determine imprecision including Thompson-Howarth plots which quantify imprecision to allow comparison between different methods and protocols. Comparing sampling imprecision between data sets and data types allows determination of optimum drilling and sampling protocols and can reflect upon the underlying validity of Mineral Resource input data and estimation outputs.CITATION:Sims, D A, Pocoe, J, Kasnanto, A N and Pulungan, B, 2017. Why combine reverse circulation and diamond drilling in Mineral Resource estimation at Purnama?, in Proceedings Tenth International Mining Geology Conference 2017, pp 413–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Kidd Mine in Northern Ontario is now producing from Stage 1 of the Mine D expansion project ? mining between 2100 m and 2700 m below surface. Planning for Stage 2 of the Mine D project is already well advanced and will see the mine extended potentially to 3100 m below the surface. To ensure adequate ventilation is maintained at such depths, two large axial fans have been installed on the 6000 Level (1800 m below surface) as exhaust booster fans to operate in series with the surface exhaust fans. The Kidd Mine 6000 Level Booster Fans are a unique installation with unique and often unexpected challenges. These challenges have been met and attacked through the combined efforts of mine and fan manufacturer personnel with a common focus.

Jan 1, 2009

Treatment of Gold-Bearing Oxide High-Clayish Ores The analysis of modern state of treatment technologies of gold-bearing oxide high-clayish ores showed that the main method applied both in Russia and abroad is sorption leaching and heap leaching with preliminary granulating. The use of any of these processes depends on many factors including average gold grade, site and area of a deposit, clay content and etc. The two processes are often used at the same deposit. In this case, rich ores are treated according to a plant technology, poor ores and ores with cut-off grade are treated with heap leaching. Both technologies possess their own advantages and disadvantages. A plant technology is characterised by high recovery with higher capital and operating costs at the same time. Lower recovery during heap leaching can be attributed to an unstable quality of ore granulating due to both technological and weather conditions. In case of poor high-clayish ores, the use of a combined ore treatment is possible and profitable. It includes the ore disintegration and a clayish fraction treatment by using a heap leaching. In this case, capital and operating costs reduce in comparison with a plant technology and the recovery increases in comparison with heap leaching. Sometimes it reaches a plant recovery. These ores possess special features. As a rule, gold is associated with ore fraction, so it liberates readily from the association with ore ore-forming minerals even with relatively coarse grinding explain their high solution velocity in a hydrometallurgical cycle. Clayish ores are characterised by high sorption activity to gold cyanide complexes as well as extremely low velocity of filtration and thickening of slimic pulps at the same time. The paper describes the options of oxidised high-clayish ores treatment, such as, a plant technology (PIP and CIP process), heap leaching and a combined technology (disintegration, heap leaching of a crystalline fraction and sorption cyanidation). The obtained results were used when selecting a treatment technology and during construction of a plant for oxidised high-clayish ores treatment.

Sep 13, 2010