Search Documents

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed. This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels. Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Mitsuru Tanahashi

In order to develop an effective process for the production of a solar-grade silicon (SOG-Si) from metallurgical-grade one (MG-Si), the oxidation removal of boron from molten MG-Si was investigated at 1773 K by the following two CaO-saturated CaO-CaF2 flux treatment processes. I) Boron removal by flux addition onto the molten MG-Si followed by oxygen gas injection into the melt (Two-stage connecting process). II) II) Boron removal by simultaneous injection of flux powders and oxygen gas into the molten MG-Si (Simultaneous injection process). These processes can establish the special condition of both high basicity of the flux and the high oxygen partial pressure at the boron removal reaction sites. Through these processes, especially by the simultaneous injection process using a flux powder injection equipment, the boron content in MG-Si can be efficiently reduced. The obtained results clarified that both processes should be conducted for a time period as short as possible by using as much flux as possible. By repeating the simultaneous injection process for 60 s three times under the optimum operating conditions determined in the present study, the boron content in MG-Si can be reduced from 14 to 4.7 mass ppm.

Jan 1, 2003

By K. H. Bech, S. T. Johansen

"The mass transfer at fluid-fluid interfaces due to turbulent agitation is investigated theoretically. In particular a theory is derived for interface stresses due to interface energy and surface renewal. This theory indicates that surface renewal may take place if the geometry is sufficiently large and if surface tension is sufficiently low.By using a model for a typical turbulent structure we compute the interface mass transfer for a stressless interface and a fully interface. Results for the general situation is not presently available. The computed results are used to derive analytical expressions for the mass transfer based on turbulent kinetic energy and free stream turbulent length scales.One important application of the theory is the mass transfer at the electrolyte side of the bath-metal interface in the Hall-Heroult process. For this process we show that mass transfer should be expected to be of the rigid surface type."

Jan 1, 1999

By E. S. Geskin

"This paper is concerned with the construction of a formal technique for the selection of a metallurgical technology. Exergy consumption is used as the criterion of process efficiency. Different items of the exergy balance are considered and techniques for the reduction of exergy consumption are determined. The selected techniques of exergy saving enable us to identify processes which should be used at different stages of steelmaking. The combination of the selected processes enables us to suggest a technology for conversion of iron ore into steel products. The selection of this technology narrows the range of further search of metallurgical processes. The paper shows that qualitative thermodynamic analysis can be used as the first step in the design of metallurgical processes. IntroductionThe existing processes for making, shaping and treating of steel enable us to convert the available iron bearing ores into marketable steel products. However, the energy cost of metal production is much higher than thermodynamically required, while the metal properties are much lower than thermodynamically available. Increasing cost and declining availability of energy and raw meterials make the creation of new steelmaking technologies imperative. In recent years, the number of novel processes for the making, refining, and shaping of steel have been suggested and tested. Some found a practical application. However, the tested technologies make up a small portion of the physically available routes for the conversion of iron ore into a marketable product. It is also not evident that the optimal routes have been tested and that the selected technologies are the best among those tested.Although the development of new metallurgical technologies must be based on the experimental and practical information, the number of the alternative routes for the making, shaping and treating of steel, as well as the cost of examining each single route, make necessary the use of analytical techniques for the evaluation of the possible ways of process development."

Jan 1, 1988

By C. J. Beyke

Slags and/or mattes from three secondary lead producers were studied as part of an effort to develop treatment methods for these lead-bearing residues. Each company used a somewhat different production process. Company A used a reverberatory furnace followed by a blast furnace. Company B used only a blast furnace. Company C used both a reverberatory and a blast furnace, and the scrap material was desulfurized with sodium carbonate prior to smelting. The slag matrix produced from sulfur-bearing scrap consisted mainly of iron-calcium silicates; the slag from desulfurized material was similar, but also contained sodium. In all the slags most lead was present in metallic form, often alloyed with tin, antimony, arsenic, and/or iron. Slag from Company B contained the most alloying elements, often as discrete subparticles within the lead droplets. Mattes were produced at Companies A and B; predominant phases were pyrrhotite and magnetite, while lead was present in metallic form and as galena.

Jan 1, 1995

By S. C. Flood, J. D. Hunt

"The columnar-equiaxed transition (CET) has been studied numerically under unsteady-state conditions using mathematical models that: (i) include a non-equilibrium undercooling at the columnar front;and(ii) describe the simultaneous evolution of the columnar and equiaxed zones.The results are discussed and compared with those produced by a steady-state analysis.IntroductionThe majority of the previous work on the columnar-equiaxed transition (CET) has concentrated on the production of equiaxed nuclei, regarding this as being the critical step in the formation of an equiaxed zone. Recently, the growth of equiaxed grains has been considered and this is not unreasonable because, for an equiaxed zone to be present, the grains must grow as well as nucleate. Since the growth rate of the grains will be determined by the thermal environment at and ahead of the columnar tips, it was decided to model the liberation and flow of heat during solidification to discover whether the various trends in the columnar range might be explained by their effect on the temperature profile throughout the casting. The models presented here for the solidification of a casting are the first to include the latent heat liberated ahead of the columnar front. Burden and Hunt (1) consider its effect only qualitatively, and although Lipton et al (2) adopt a criterion for the CET which is based on the thermal interaction of the columnar and equiaxed grains, they do not actually include the latent heat in their calculations.It can be argued that the latent heat liberated by the equiaxed grains in the bulk will retard the columnar dendrites in a casting: once the equiaxed grains are sufficiently well-established, the latent heat that they evolve could slow down the columnar growth to such an extent that the equi axed would dominate. Alternatively, the latent heat produced by the equiaxed grains might suppress further equiaxed solidification by raising the bulk temperature. The nature of the thermal interaction between columnar and equiaxed growth is not obvious, and because it is dependent on the material parameters and the dimensions of the system, it cannot be considered effectively in a qualitative way but has to be studied quantitatively: hence the need for the mathematical models discussed in the following pages. The results of the models are discussed in the light of a steady state analysis."

Jan 1, 1986

By Kang Wan, Lei Tang, Jianchao Li, Jieyu Zhang, Minqi Sheng, Jifang Xu

"The viscous flow phenomenon in slag close to the liquidus temperature was considered. A simple approach that liquidus temperatures of melt could be derived from viscosity data was employed. The potential of this method for estimating the liquidus temperatures of pure water and binary alloy was demonstrated. The liquidus temperatures of the CaO-Alz03 based slags obtained from the second derivative method depends upon the number of viscosity values available at different temperature intervals. The results indicated that plots start deviating from the straight-line behavior at temperature as expect, and the second derivatives show the break points at a certain temperature, which is the liquidus temperature. Comparisons among the present observations as well as the characteristic temperature of the selected slags, which measured by the hemisphere method and DSC, indicated that it is possible to get a reasonable idea of estimate the liquidus temperatures from activation energies for viscous flow.IntroductionThe liquidus temperature of slag, which has a significant effect on the kinetics of chemical reactions and the slag-metal separation, is extremely important for metallurgical operations. Experimental measurements of the liquidus temperatures of slags are difficult, since slags invariable supercool. In addition, behavior of a single constituent in a multi-component slag is different in different circumstances due to its interaction with other constituents. Hence, it is essential to study the liquidus temperature of each particular slag resulting from a special process. Usually, the compositions of the slags aimed to the single liquid region of the phase diagram. However, the phase diagram of many slag systems, which back often to the 1950's, involves considerable uncertainties. Many liquidus temperatures are given as dotted lines in Slag Atlas [1]. Disagreements between the phase diagram and the reality have been found [2]."

Jan 1, 2013

By Steven M. Puricelli

Sulfuric acid plants associated with smelters, have historically been an overworked and often neglected pollution control device. They could do little more than manage the wide fluctuations in gas flow and SO2 strength from the smelter. With the introduction of flash smelting, the picture began to change, but the fluctuating batch converters continued to dictate acid plant design. More recently, the commercial use of continuous converting processes utilizing high levels of oxygen enrichment has dramatically upgraded the SO2 strength and stabilized the gas flow to the acid plant. The SO2 gas now issues continuously and at concentrations that allow for compact and, cost effective acid plants. Relieved of the burden of excessive dilution air, the heats of reaction can also be recovered as medium pressure steam and used to drive a generator, making the acid plant a net producer of power and a valuable asset to balance sheets. This concept was put into practice at the Kennecott Utah Copper Corporation smelter modernization project, located in Salt Lake City, Utah. The new acid plant, which was commissioned in June of 1995, is a sophisticated, low environmental impact, energy producing plant, worthy of review. This paper examines the key features of this acid plant, such as controlling its tail gas, by catalysis alone, to an environmentally friendly, 100 ppm of SO2, while feeding the acid plant converter with an efficient 14% SO2. The acid plant is also a prudent steward of energy resources, recovering 220,000 lb/hr of 140 psig steam from process heat which is used to generate a substantial 20 MW of gross power. Also discussed will be some of the ongoing issues, such as handling of selenium and fluorine in the gas cleaning sections, as well as a review of some. of the problems that were identified and resolved. Today's modem acid plants, by necessity, are becoming a producer of quality, valuable products, making the acid plant an asset and not a liability. Plants like Kennecott are already gaining wider acceptance and are expected to be the vision of the future.

Jan 1, 1998

By Varadarajan Seshadri

The performance of mould fluxes in satisfying its quality requirements can have a significant effect on the efficiency of the continuous casting process and on the surface quality of the products. This performance is affected by various parameters including the characteristics of the mould fluxes, the quality of the steel being cast and the operational conditions of the caster. The extremely complex relationships involving the parameters mentioned above make it very difficult to have simple criteria for selecting mould fluxes for casting a certain grade of steel in a continuous casting machine. These difficulties led steelmakers and mould flux suppliers to select mould fluxes based mainly on plant trials. In the present work, a software to help in the analysis and development of mould fluxes for continuous casting was developed_ This software includes several models for prediction of mould flux viscosity and consumption. A mathematical model was also used to predict the heat flux through the mould flux. The proposed methodology was applied to continuous casting of crack sensitive steels_ Some of the results given by this software are presented, discussed and compared to plant data.

Jan 1, 2003

By Tracie Zoeller, G. Paul Neitzel, Jr. Sanders

"As-cast aluminum alloy microstructures are highly segregated. Coring occurs when solute is rejected during solidification resulting in a non-uniform solute distribution across the dendrite arms. Furthermore, coarse constituent phases are formed in the interdendritic channels as a result of coring. These constituents are either soluble or insoluble and can form from the major solute elements, or the impurity elements iron and silicon. The dissolution of these constituents, or precipitates, is an important consideration in determining the microstructural evolution of an alloy. The properties of an alloy are significantly affected by the morphology of the precipitates. Precipitates can be either beneficial or detrimental to the properties of the alloy. Regardless of the nature of the precipitates present, it is useful to understand the dissolution process. A diffusion-limited dissolution model for planar precipitates is presented and compared to an analytical solution and to models in the literature. Experimental data for the dissolution of AhCu precipitates in a dilute alloy are compared to the proposed model, and found to have good agreement.IntroductionDuring the processing of precipitation hardening alloys, beginning with the solidification step and ending with the final solution heat treatment step, there are a variety of particles that form. Some of these particles must be dissolved and solute redistributed and re-precipitated in a more homogeneous distribution than as it first appears in the as-cast microstructure. The particles can be classified by size as microstructure develops during processing. Coarse particles that form during solidification can either be soluble, partially soluble or insoluble. These particles can be the result of coring of the major solute elements as well as the limited solubility of elements such as iron and silicon. Iron and silicon can combine with the major solute elements such as copper in 2xxx alloys forming coarse phases often referred to as constituents. Figure l(a) shows the as cast microstructure with the constituent phases, Al2Cu and the insoluble phases containing Al-Fe-Mn-Cu-Si [7]. During preheating the soluble phases such as AhCu that were formed by eutectic decomposition must be taken back into solution, whereas the insoluble phases remain essentially unchanged by most thermal operations. Figure l(b) and (c) show some of these constituents after subsequent preheating steps. In Figure l(b), AhCu platelets are shown and in Figure l(c) the remnants of the AhCu phase are noticeable, along with Mn-bearing dispersoid phases. Reduction in the volume fraction and size of these phases improves the ductility and fracture toughness as well as reducing the inhomogeneities that occur during coring. Also adjacent to the dendrite arm boundaries are smaller AhCu phases that precipitate by a solid-state transformation on cooling to room temperature."

Jan 1, 2004

By A. Rosenfeld

The feasibility of applying laser induced optical emission spectroscopy to the high speed sorting of mixed alloy aluminum scrap is investigated. The basic spectroscopy for analysing aluminum alloys for the major alloying elements over their full concentration ranges is established. Materials handling issues are also described and the components of an overall sorting system are presented.

Jan 1, 1995

By Lu Lin, Yan-ping Bao, Min Wang

In order to forecast the cost of dephosphorization during BOF process, and achieve economical dephosphorization of BOF. The mathematical model of dephosphorization cost for BOF process was established. The model calculations show that, when the silicon content and phosphorus content are increased in hot metal, and the final phosphorus content of BOF is decreased, the dephosphorization cost will be increased. The silicon content of hot metal is increased of 0.1% in the plant, the dephosphorization cost is added by 9 RMB/ton steel. The De-P cost of mode A is much higher than the other two modes for three typical production modes of single slag melting process, when the phosphorus content of hot metal is higher than 0.14%, an increase in the phosphorus content by 0.01%, the De-P cost of mode A is added by about 7 RMB/ton steel. Meanwhile, when the phosphorus content of hot metal is lower than 0.165%, the De-P cost of mode C is higher than mode B’s. For BOF single slag melting process, the dephosphorization cost calculated by model is between ± 2%, proving that the model is reliable for the prediction of dephosphorization cost.

Jan 1, 2015

By Ted H. Eyde

Natural Zeolites are a less expensive and in certain applications a superior alternative to organic ion exchange resins. Mining and metallurgical waste streams are difficult to treat because the effluents which contain potentially valuable heavy metals such as copper, lead, and silver are often highly acidic and contain significant quantities of suspended solids. Under rigorous operational conditions, certain natural zeolites can remove the metals, which if desired can be recovered by either elution or conventional smelting techniques. There are significant differences in cation exchange rate, selectivity and capacity as well as resistance to either high or low pH, blocking cations and tolerance to elevated or depressed temperature and pressure not only between different zeolite minerals but between the same mineral from different deposits. Applying natural zeolites to the treatment of mining and metallurgical waste streams depends on matching the specific zeolite to the effluent by characterization of the zeolite minerals.

Jan 1, 1993

By William J. Pardee, Michael A. Shaff

"Deeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will accelerate productivity growth and materials science application through the ease with which they can be modified to accept new materials knowledge and sensors. Carbonization of resin matrix carbon fiber composites, specifically, is a violent solid state chemical reaction with large stresses due to gas pressure, matrix shrinkage, and differences in thermal expansion. The matrix strength falls sharply, then rises again during the process. At least two competing reaction paths are important; the first cleaves methylene bonds, reduces toughness, density and stiffness; the second reforms those bonds, ultimately resulting in aromatic ring condensation that increases density, strength, and modulus. Since these reactions have different temperature dependencies, one can expect to shift the process towards the second path by changing the heating rate, but that change must be accomplished without producing macroscopic interlaminar crack growth. To accomplish this, we employ gas sensors to infer matrix chemical state and acoustic emission to identify microstructural changes and to recognize brittle fracture. The latter does not prevent delamination, but is important in testing models for the causes of delamination and in improving the processing cycle. This paper describes a control strategy to accelerate the process while still lowering the risk of failure.IntroductionDeeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will be more easily modified to accept new materials knowledge and sensors, thus accelerating productivity growth. Such a control strategy for carbonization control is described below.Carbon-carbon composites are time consuming and costly to manufacture. Processing methods have been developed empirically and are usually very conservative because the process often fails when any change is made. Apparently minor changes in materials or geometry can produce failures that are difficult to diagnose and correct. We will describe below several essentially unavoidable sources of variability. These are best dealt with by applying materials science to adapt (i.e., closed loop control on materials properties) the process in real time to reduce the effect of unavoidable model idealizations, material variability and environmental noise. The most critical issue in control of the carbonization process control is avoiding catastrophic delamination. The strategy developed below makes use of a priori materials knowledge and real time sensors to accelerate the now very slow process without destroying the material, and without requiring unreasonable resources to determine the statistical properties of the material."

Jan 1, 1988

By Jack S. McPartland

Historically, research on thiosulfate leaching of precious metals ores has been focused on processing of difficult to treat ores. Thiosulfate leaching of ores and concentrates containing sulfide minerals, copper, manganese and preg-robbing carbon constituents has been evaluated. Cyanide leaching is generally considered an efficient, environmentally acceptable means for processing of non-refractory precious metal ores, Consequently, commercial processing of finely disseminated, oxidized precious metal ores is normally accomplished using alkaline cyanide leaching. Recent changes in regulatory climate have, however, called into question the acceptability of cyanide leaching in a number of locations worldwide. In some cases where the use of cyanide is being questioned, thiosulfate leaching may provide an acceptable alternative. Developments in thiosulfate leaching of precious metal ores are reviewed in this paper.

Jan 1, 1999

By Peter K. Eriksson

Nanofiltration is very efficient in separating heavy metals from water solutions, even if they contain strong acids. Desalination System, Inc., has many years of experience in this area, and this paper deals with three different such cases. The first case deals with concentrating the heavy metals in the pregnant leach solution from a copper dump leaching site with a surplus water problem. The increased copper concentration in the pregnant leach solution increases the capacity of the following copper extraction stage. The nanofIltration permeate is polished with a biomass adsorption column to remove the small amounts of remaining heavy metals, before being discharged. This method eliminates sludge handling and disposal, which are quite costly with the alternative precipitation process. In the second case, a complicated precipitation method was used to remove heavy metals from the waste stream of a specialty metals manufacturer. Nanofiltration was installed to increase the metals concentration four times, which greatly simplified the precipitation process. The chemical consumption and sludge production decreased by more than 80 percent, and the labor cost decreased by 66 percent. In the third case, nanofiltration was used to purify waste sulfuric acid solutions containing heavy metals, to meet the specifications for technical grade acid. Sulfuric acid concentrations above 30 weight percent were successfully purified in a multiple pass membrane system.

Jan 1, 1996

By Md Sazzadur Rahman

Electrochemical Impedance Spectroscopy studies were conducted on two organic thermal energy storage materials; Neopentylglycol (NPG) and 2-Amino-2-Methyl-1,3-Propanediol (AMPL). The ionic conductivities and dielectric relaxation times in the low temperature ordered a-phase (monoclinic for both NPG and AMPL) as well as high temperature orientationally disordered cubic y-phase are reported.

Jan 1, 2006

By K. Gao, R. Dry

"Carbon boil, which results in excessive spitting and even complete destruction of a metal drop, could significantly influence the efficiency of direct smelting processes. Carbon boil has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure, and melt area/volume ratio. The time of carbon boil was determined using a CCO camera coupled with a time/date generator connected in parallel to a video recorder and a computer. The time of carbon boil was in the range ~5 - 15 seconds under the conditions in this study. A mechanism for carbon boil has been proposed.IntroductionThe occurrence of carbon boil in molten iron drops can result in excessive spitting and sometimes even complete destruction of a metal drop. In direct iron smelting processes, this could significantly influence the decarburisation of liquid metal and the post combustion and hence may influence the efficiency of smelting processes. The generation and consequent ejection of metal droplets into the gas phase occurs due to the intense turbulence in the bath which results from the injection of gases and coal. The aim of this investigation is to understand the fundamentals governing the carbon boil phenomenon under direct iron smelting conditions to assist control of process efficiency.Carbon boil phenomenon has been studied as a function of some key parameters such as melt sulfur content, oxygen partial pressure and melt area/volume ratio. The time for the occurrence of carbon boil has been determined in this study at 1440 °C using a novel approach which includes utilisation of a CCD camera coupled with a time/date generator connected in parallel to a video recorder and a computer. This arrangement permits the capture of the entire sequence of events leading up to carbon boil and therefore the determination of time of boil which is in the range -5 - 15 seconds under the conditions in this study."

Jan 1, 1996

By N. A. Warner

To filly secure the environmental and social acceptability benefits of making a sulphide smelting facility and its ancillary sulphuric acid plant or other means for fixing sulphur, a virtually zero gas emission operation, it will be necessary to utilise exclusively technically pure oxygen. The strategy proposed for preventing the smelter from overheating involves highly efficient energy transfer by promoting sulphur trioxide formation at a relatively higher temperature than normal. A closed-loop gas circuit uses an eductor system actuated by the process oxygen to recirculate sulphur trioxide and unconverted sulphur dioxide back to the smelter, the endothermic dissociation of sulphur trioxide becoming a major contributor to the removal of excess heat. The only gases leaving the system relate to the bleed of nitrogen impurity introduced in the tonnage oxygen.

Jan 1, 1998

By S. S. Chabot, S. E. James

A recent survey of CEOs from major steel companies worldwide revealed the importance of recycling zinc units from EAF dust, mill scale, blast furnace dust, and other zinc containing streams in their plants. Many processes were developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and selling it to primary zinc producers to recover the metal value. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of corrosion problems it will cause in electrolysis. In 1999, BRZ installed a zinc oxide receiving and washing plant to minimize the impact of halides to its circuit. A description of the washing plant and initial operating results are included.

Jan 1, 2000