Search Documents

By Qingwei Qin, Ping Xue, Guangqiang Li

Ausmelt furnace slag contains about 0.9% Cu (mass %). With increasing the amount of Ausmelt furnace slag, the recovery of copper from it will produce an enormous economic yield. The recovery of copper by floatation from slow cooled Ausmelt furnace slag was studied in this paper. The phases and composition of the slow cooled slag were analyzed. The factors which affected the copper recovery efficiency such as grinding fineness, pH value of flotation medium, different collectors and floating process were investigated. It was shown that the size distribution of the primary grinding and secondary grinding of middling were 75% for particles less than 0.074mm and 82% for particles less than 0.043mm respectively. The closedcircuit experimental results with butyl xanthate as collector in laboratory showed that the copper grade reached 16.11% and the recovery rate of copper reached 69.90% and the copper grade of tailings was only 0.2%.

Jan 1, 2015

By P. A. Botha

The coal seams in the Waterberg basin occur in correlates of the Vryheid and Volksrust Formations as developed in the main Karoo basin. In the Vryheid Formation, five thick seams of predominantly dull coal are present, whereas a multitude of thin, lenticular seams (a few millimetres to 2 metres}, predominantly of bright coal, are developed in the overlying Grootegeluk Formation. During exploration, the coal seams were divided into 11 zones. Analytical data on float and middlings fractions (RD less than 1.40 and between 140 and 1.80, respectively} were used mainly for stratigraphic correlation of the zones in the Grootegeluk Formation. The affinities of the major and trace elements for different mineral phases and/or organic material are discussed on the basis of correlation matrices and vertical variation diagrams. Titanium and vanadium clearly show some degree of organic affinity. P 205' AI203 and alkaline-earth elements are also positively correlated by the presence of goyazite in the coal. This type of investigation gives an indication of the degree to which undesirable elements like P and S can be removed during coal beneficiation, of which coal zones are unsuitable for the production of metallurgical coal on account of a high content of these elements, and to what extent the blending of different coal zones is required to keep the concentration of these elements within acceptable limits.

Jan 1, 1991

By Mikiya Tanaka

Keywords: Solvent extraction, nickel, electroless plating, accelerating effect With the increasing importance of electroless nickel plating technology in many fields such as the electronic and automobile industries, the treatment of spent baths is becoming a serious problem. Although the spent baths are currently treated by a conventional precipitation method, a method with no sludge generation is desired. Previously, we proposed the solvent extraction recovery of nickel from the spent baths by means of solvent extraction using LIX84I as the extractant. However, a problem of this method was that the extraction and stripping of nickel were not fast enough to achieve high efficiencies when the continuous extractor was used. We have overcome this difficulty by finding that the addition of an acidic organophosphorous reagent in small amount into the organic phase markedly promotes the extraction and stripping rates of the nickel. Shaking-out tests using a separatory funnel at 240 spm revealed that the time to reach the equilibria is more than 60 min with only 20 vol% LIX84I, but is reduced to 10 min and 2.5 min by adding 2 vol% DP8R, respectively, during the extraction and the stripping with sulfuric acid.

Jan 1, 2004

By Robin D. Rogers

Room temperature ionic liquids (RTIL) can replace certain traditional organic solvents in liquid/liquid extraction of metal ions from aqueous systems. The very low vapor pressure and non-flammable nature of RTIL warrant consideration of these neoteric solvents for new processing technologies which will reduce pollution, Increase safety, and lower costs. Metal ion separations in RTIL, however, will typically require the use of an extractant and research is needed to identify suitable selective extractants which have appreciable solubility in the RTIL and low solubility In the aqueous phase. Choice of extractant should also take into account the toxicity, expense, and disposal of the ligand.

Jan 1, 1999

By Ruhi Bux, Akshay Verma, Mohini Saxena, P. Asokan

"Due to the colossal increment in the industrialization, the generation of wastes gathered as a result of different extraction, benefaction and generation processes is having an alarming problem for waste disposal. The best and most acceptable way is to use the waste in accordance to its potential for the generation of high value lucrative composite goods. The study in this paper elucidates the potential of several industrial wastes like fly ash, red mud and marble slurry dust for the production of different wood substitute products like doors, windows, roofing sheets and instant houses for the rehabilitation on the sites of catastrophes. Wastes were initially characterized for the physical, chemical and mineralogical properties and then used in different formulations with binder like Polymer along with natural fiber like Jute to intensify the physical as well as mechanical properties of the resultant composite. The study also reveals that these composites have better mechanical properties than the available ones like teak, medium density board, Rice husk board etc. Also, the fly ash and red mud composites have better mechanical properties than marble slurry based composites. The results fosters the implementation of natural fiber with the industrial waste in the generation of eco-friendly and non-hazardous composites.IntroductionOver the last few decades, there has been a tremendous increase in the generation of industrial wastes gathered as a result of various extractions, benefaction and generation processes. The condition worsens even, when it comes to high quantum generated wastes like Fly ash, Red mud and Marble slurry dust. The primordial motif behind the incorporation of industrial wastes as filler in the development of composites is primarily composed of two main objectives; Firstly waste management, the colossal waste dissemination in the environment has disturbed the ecological balance by polluting land, surface water, ground water, air, natural resources and even disturbing the public health [1]. Secondly, to act as a perfect substitute for the conventionally existing building materials, this will aid in dwelling places to many with the least incorporation of exhaustive natural resources as woods quid pro quo."

Jan 1, 2008

By Larry M. Southwick

Pneumatic converting (Bessemerizing) of iron revolutionized the steel industry. Bessemerizing of copper (conversion of copper sulfide matte to copper metal) was proposed at almost the same time, but it was slow in being accepted. The differences between iron and copper converting were great and technical problems were substantial. It took 25 years for the process to become viable and another 25 years before a truly economical solution was found. A major economical and productivity problem was the short life for converter refractory linings. The first converters had acid (silica) linings, which were quickly consumed since silica was a flux for the process. Converters had to be relined at least once per day, a laboriously expensive manual process with only the most rudimentary mechanical aids available to assist. The industry was revolutionized almost overnight when finally a viable basic (magnesite) lining was developed. This lasted 100's of days versus less than one, leading to converters that were easier to operate and which handled larger charges. This change occurred after W.H. Peirce and E.A.C. Smith, with support from the Guggenheim interests, successfully operated a basic lined converter in a copper refinery in Baltimore. While Peirce and Smith are generally given credit for the development and explosive acceptance of this idea, a Pittsburgh industrialist, Ralph M. Baggaley, working in an independent smelter in Butte, Montana, successfully built and operated a basic lined converter four years before they did. In fact, the early support for Peirce and Smith likely occurred because Guggenheim's staff were encouraged after thoroughly examining Baggaley on his earlier successes. The questions of technology primacy between Baggaley and Peirce/Smith are ironically similar to those between Wm. Kelly and Bessemer in converting iron to steel. This paper will review what Baggaley (and other early researchers) accomplished, examine why he (or they) did not receive credit equal to Peirce and Smith and explore what his (their) place should be in the development of successful basic linings. More suspects than a Victorian Whodunit.

Jan 1, 1999

By Igor Rojkovic

The most important uranium mineralization in the Western Carpathians occurs in the Permian rocks. Low grade stratiform uranium mineralization was formed during the Permian due to adsorbtion and reduction by organic matter, titanium oxides, iron hydroxides, pyrite and clay minerals. During the Alpine orogeny uranium (± molybdenum and copper) remobilized stratabound ores were formed. Dominant ore minerals are uraninite, U-Ti oxides, molybdenite, pyrite and chalcopyrite Two generations of ore minerals are reflected by their textures and chemical composition.

Jan 1, 1995

By Isabela Leao Amaral da Silva, Alice Barreto Bevitori, Frederico Muylaert Margem, Victor Bastos da Silva, Sergio Neves Monteiro, Artur Camposo Pereira

"The jute fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of DGEBA/TETA epoxy composites reinforced with jute fibers with different diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned jute fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, separated fibers with smaller larger diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinnest jute fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionThe interest of this research is to develop composites with epoxy resin matrix reinforced with continuous and aligned jute fibers, for applications in various industries, including construction and automotive industry. Conflicts related to the use of non-renewable forms of energy are increasing the interest to enter the market to replace natural materials, synthetic materials synthetics have a higher power consumption in its manufacture [ 1-4].Therefore, applications of natural lignocellulosic fibers obtained from cellulose-based plants are receiving increased attention as an alternative to replace more environmentally correct nonrecyclable materials, energy intensive and glass fiber composites in [5-6]. The use of composites reinforced with natural fibers is a reflection of the concerns with environmental issues such as pollution caused by waste that is not biodegradable or cannot be incinerated and climate change due to C02 emissions associated with the processes of intensive energy and also motivates this work to develop self-sustaining, since natural fibers generate a source of income, especially in developing countries, where most originate, encouraging the cultivation of non-food agriculture [7-9]. Additionally, it is worth also remembering that these fibers come from renewable sources, in addition to being abundant, inexpensive and have a relevant set of mechanical properties [10]."

Jan 1, 2013

By Kazusuke Sato, Takahiro Uno, Koji Hoshino

"A novel Ni coating technique of Ni(OH)2 powders was developed to improve the positive-electrode performance· of the Ni-MH batteries. It was found out that Ni(OH)2 powder was reduced by N2H4 without any catalysts in an alkaline - solution at high temperatures. In result of observation of pH and potential changes in the solution during the reaction, it was found that the reduced species was HNio2- ion dissociated from Ni(OH)2 in the alkaline solution. The molar fraction of reduced Ni of the Ni(OH)2 was increased in proportion to the amount of added N2H4. At the small Ni fraction, a porous Ni layer was formed on the surface of Ni(OH)2 powder. Open cell tests were carried out with the paste type electrodes made of either the Ni coated Ni(OH)2 powder or non-coat powder, and cell performances were compared. In result, it was found that the Ni coating technique is effective on improvement in the utilization of Ni(OH); as a positive-electrode active material under high current densities.IntroductionNi-MH rechargeable battery is generally used for the power source of portable machines and electric vehicles because of its good performance at high energy density and. long term cyclical life as well as cleanness and good safety. Cell component materials have been improved respectively, and as concerns ·the positive-electrode reducing 'the internal resistance is a principal problem to improve the discharging performance at higher current densities.In recent years, improved Ni(OH)2 powders coated with conductive materials as NI. or CoOOH have been developed for the· positive-electrode active materials in order to· reduce the internal resistance of the electrode1)· 2) The Ni coated Ni(OH)2, however, is costly because it is fabricated by .the -non-electrode plate technique which needs a expensive precious ·metal catalyst as PdC12We found that Ni(OH)2 powder was reduced by N2H4 without any cryatalysts in an alkaline solution at high temperatures. After the treatment, Ni(OH)2 powder become gray color like Ni powder from light-green color; and. turned into a magnetic. In this study, the mechanism of the -reducing reaction was investigated to apply the reactions .to a novel Ni coating technique of Ni(OH)2 powders, · and the performance of the Ni coated Ni(OH)2 powder obtained by the reducing process was evaluated as an -positive-electrode active material of Ni-MH batteries."

Jan 1, 2000

By K. Soldenhoff

The Bulong deposit, situated near Kalgoorlie in Western Australia and owned by Resolute Limited, is a lateritic deposit containing on average 1.1% nickel and 0.09% cobalt. A process has been developed and tested at the mini-plant scale for direct solvent extraction and separation of Co and Ni from solutions derived by acid pressure leaching of Bulong ore. In this paper, two solvent extraction processes are described. The first process uses Cyanex 272 to extract cobalt and reject nickel to the raffinate. The second process uses Versatic 10 to extract and purify nickel. The loaded strip nickel solution is suitable for electrowinning. Results of both batch laboratory tests and continuous mini-plant trials are presented. The selectivity of the solvents with respect to the major impurities such as Mn, Mg, Ca, and Zn is also discussed.

Jan 1, 1998

By H. Fukushima, T. Ohgai, N. Baba

The electrodeposition behavior of Zn and the morphology of the deposited Zn were studied in electrowinning solutions containing polymer additives such as gelatin and polyethylene glycol (PEG). The cathode potential was shifted in a less noble direction and the polarization resistance for Zn deposition increased with increasing concentrations and molecular weights of both gelatin and PEG added to the electrolytic solutions. However, when the molecular weights of these additives exceeded about lxlO4, the cathode was depolarized and the polarization resistance for Zn deposition decreased with increasing molecular weight. The crystal grain size and the (002) orientation of the deposited Zn became smaller when the concentration and molecular weight of the additives increased, and the cathode was polarized.

Jan 1, 2000

By L. Salinas

Lance injection of gas and particles into a molten bath is currently practised in metallurgical processes (Mitsubishi lances for example). Several experimental and theorical studies have been conducted in the past on this topic. However, neither detailed calculations nor experimental studies of local flow patterns have been published. In the present work, a numerical simulation of the interaction of a gaseous vertical descending jet and a liquid surface was done, using the turbulence k-e model. There is a fair agreement between the calculated and the experimental values. The results of this study demonstrate that it is crucial that the gas jet velocity profile and turbulent characteristic are correctly formulated in order to correctly simulate the system.

Jan 1, 1999

By Han Ilhan

This paper discusses and describes aspects of a cost effective and safe tailings impoundment selection. In light of the current low metal prices and recent tailings embankment failures around the world, it is becoming extremely more important to develop tailings impoundment design that balance cost efficiency with safety. The paper will present critical design components associated with a tailings impoundment which need to be addressed during the planning phase. Procedures for identifying various tailings impoundment alternatives, and evaluation and selection of alternatives are presented.

Jan 1, 1999

By E. V. Verhoef

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-lndicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LeA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LeA assessments, thus leading to erroneous results. The suggested approach provides directions for including these external effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By E. V. Verhoej

The proposed EU directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment promotes the substitution of lead in consumer electronics to reduce emissions from lead in the end of life phase. In this paper, the consequences of substituting lead in solders is assessed using the Eco-Indicator-99 method for the examples. The base metal production system is considered as an interconnected network modeled dynamically in Simulink 4 and Matlab 6 (Mathworks Inc 2000), where the recovery and production of metal components of the assessed product partially overlap. This approach requires global modeling of metal production processes and mass balances and resulting allocation choices. It also reveals the susceptibility of LCA scores to different choices in the modeling and data availability and uncertainty. Besides the comparison between lead-free and lead-containing solders, other side effects are revealed. Lead is carrier material for the recycling and production of many co-elements in the interconnected production and recovery system. Substitution may have adverse effects such as temporary shortages of other connected metals that are often not considered in normal LCA assessments, thus leading to erroneous results. The suggested approach provides directions for including these extemal effects and for further assessment of the environmental effects of substituting lead. This paper shows that in order to assess the environmental aspects of metallurgy, dynamic modeling of the total system is required based on the fundamental thermodynamics in each metallurgical reactor, the basis of this dynamic model. With this the true environmental impact of metallurgy can be explained. In the case of lead free solder, it is shown that the mining of substitutes has a very much larger impact.

Jan 1, 2003

By W. K. Tolley

The Bureau of Mines is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from CdTe scrap produced in the manufacture of infrared optic devices. Sulfation, ferric chloride leaching, and oxygen-pressure leaching have been tested. Cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. However, no satisfactory scheme for dissolution of the higher valued tellurium has been devised. Leaching the ground CdTe for 75 min at 110°C in 1.1M H2S0, under 120 psig 0, yielded 99.5% Cd extraction. Tellurium remained in the leach residue as TeO, and elemental tellurium; residual cadmium was less than 0.5%. The cadmium in the leach liquor was purified of coextracted metals such as gallium and iron by adjusting the pH. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Recovery of by product metals, notably gallium, is possible.

Jan 1, 1991

By Dhanesh Chandra

Metal carbonyls are of great importance in chemical vapor deposition (CVD), composite materials fabrication, and other near-net shape technologies. Carbonyl CVD application applies to deposition of high-purity metallic/alloy coatings. Vapor pressures of solid Os3(CO)12,Rh6(CO)16, Ru3(CO)12, Ir4(CO)12, Re2(CO)10, Co2(CO)8, Cr(CO)12,, and W(CO)6carbonyls have been measured using gravimetric-torsion effusion system. The vapor pressure data is used for many low and high temperature CVD applications. Interesting decomposition/disproportionation vaporization behavior has been notedfor Rh6(CO)16, Ru3(CO)12 and Co2(CO)8. The vaporization studies of Rh6(CO)16 showed virtually complete decomposition to Rh metal and the measured molecular weight of the effusing gas from the solid Rh6(CO)16 was 27.75 g/mol, close to that of carbon monoxide as compared to 1065.56 g/mol for the value of solid Rh6(CO)16. Electron microscopic characterization, X-ray line broadening results for Rh carbonyl has been performed on the vaporization product. However, Ru3(CO)12, Co2(CO)8 showed very complex behavior. The molecular weights of the vaporizing species have been estimated and the numbers of vaporizing species are proposed. For example, there was partial decomposition of Ru3(CO)12to(approx. 52%) metallic Ru and CO gas during vaporization, as suggested by the difference in the molecular weight of the vaporizing species of 107.58 g/mol compared to the actual value of 639.33 g/mol. The dimer Co2(CO)8 partially disproportionates to tetramer Co4(CO)12, monomer Co(CO)4, and CO gas. Whereas, the Os3(CO)12, Cr(CO)12,, and W(CO)6have shown virtually no disproportionation. The total vapor pressures of all the above-motioned carbonyls, partial pressures of various species, average molecular weights of the effusing gases, equilibrium constants for the vaporization reactions, their enthalpies, entropies, and Gibbs energies will be presented.

Jan 1, 2006

By T. A. Venugopalan

The 'Hall-Heroult' Process of reduction of Alumina to Aluminium has remainded basically the same for over 100 years, but the technology has been undergoing drastic changes with respect to selection of materials for Cathode and Anode, and also energy consumption. The latest generation pots have a working life of about 1800-2000 days normally. After the failure of the pots, the Cathode Lining is dug out and disposed of on land. Since the lining contains objectional materials causing pollution, various processes have been tried for re-processing of this waste. However, most of the processes have been unsuccessful from the techno-economic point of view. At Hindalco a new chemical process for converting the fluorine values of the dug out material to Cryolite was developed in 1988 and a" one ton per day Cryolite production plant has been operating since 1989. This process is especially applicable where the integrated Alumina and Smelter Plants exist side by side. The experience in operating this Plant is discussed in detail in the paper.

Jan 1, 1992

By Gavin K. W. Freeman

The efficient separation of cobalt from nickel is a fundamental objective in the refining of cobalt. Based on recent experience at the Corefco refinery in Fort Saskatchewan, the identification of a novel process for the selective precipitation of cobalt from aqueous ammonia leach liquors is described. The addition of calcium sulphate, CaSO4.2H2O (gypsum), to an aqueous solution containing cobalt(III) hexammine sulphate, [Co(NH3)6]2(SO4)3, will result in the precipitation of a sparingly soluble double salt having the stoichiometry, [Co(NH3)6]2(SO4)3.2CaSO4.xH2O, where x = 4 or 6. Leach residues, which may contain a significant quantity of cobalt associated with the cobalt calcium double salt, can be washed with process solutions that contain ammonium carbonate. After contact with ammonium carbonate, the cobalt is recovered into solution, while the calcium is re-precipitated as the insoluble carbonate. The simplicity of this elemental separation and its high selectivity for cobalt, as well as the demonstrated usefulness in improving cobalt recoveries, are the basis for the potential applications of this process.

Jan 1, 2003

By Shulan Wang, Xuan Liu, Li Li

"Electrochemistry of Fe(III) in 69CaCl2-12CaF2-19KF and 81CaCl2-19KF (mole percentage, %) was investigated at 827 oC on molybdenum electrode by cyclic voltammetry, chronoamperometry and galvanostatic electrolysis using Fe2O3 as the Fe(III) source. The reduction of Fe(III) to Fe was conducted in one step and controlled by diffusion process. Fe(III) shown greater reduction rate and diffusion coefficient in molten 81CaCl2-19KF than in 69CaCl2- 12CaF2-19KF. Galvanostic electrolysis of Fe was performed in both molten salts with a cylindrical cathode rotating at 200 r/min and dendritic iron deposit was obtained.Keywords: iron; electrolysis; electrochemistry; molten saltIntroductionThe production of iron and steel causes huge emissions of CO2. Iron electrowinning in molten salts with dissolved Fe2O3 using an inert oxygen evolving anode is an alternative process to reduce or eliminate the formation of CO2. Research on novel process of producing metal has been reported recently [1-2] by using CaCl2 as the main electrolyte and dissolving CaO in CaCl2 due to the high solubility of CaO in the melt. This process has been used in preparing many active metals and alloys [3-14]. In the present work, the electrochemical behavior of iron in CaCl2-KF was studied and transport property of iron ion in the melt was discussed.ExperimentalCaCl2,CaF2 and KF (in analytical purity) were dried in air for 48 h. Mixed salts used in experiments were placed in a graphite crucible (??58 mm inner diameter). The graphite crucible together with the salts was heated at 473 K for 12 h in a furnace with flowing Ar (99.99%) before further heating. Temperature inside the furnace was measured by an S type thermocouple. Electrochemical measurements, such as cyclic voltammetry and chronocoulometry, were performed in a three electrode cell by EG&G PAR273A potentiostat/galvanostatand. Galvanostatic electrodepositon of iron was conducted in a two electrode cell. Molybdenum (??2 mm) and iron (??5 mm) were used as the working electrode (WE) and the reference electrode, respectively. A graphite crucible and a magnetite rod (??25 mm ) consisted of 100% magnetite and sintered at 950 oC in argon atmosphere for 2 h with electrical conductivity of 366 O-1m-1 at room temperature were used as the counter electrodes in the galvanostatic electrolysis experiment. Carbon (??10 mm) was used as the counter electrode in electrochemical measurement. The deposits were washed in distilled water bubbled with argon and dried in air before being characterized by X-ray diffraction (PW3040/60 diffractometer) and scanning electron microscope (SEM, SSX-550)."

Jan 1, 2014