Search Documents

By Masayasu Kawahara

"The extraction and separation of nickel, cobalt and copper were investigated with a solvent impregnated resin which was produced from UX84-I and XAD-4. The extraction behavior of metals with the solvent impregnated resin is similar to that with solvent extraction. The extraction ability of solvent impregnated resin improves when using finer particle resin and with a higher concentration of extraction solvent.IntroductionSolvent extraction is well known-as a method for separation of metallic elements in solution. However there are problems with intermediate phase and solvent loss. Ion exchange resin is also used in hydrometallurgy, but it is not fit for separating a large quantity of metals. Amberlite XAD-4 resin is known as a absorption agent of organic matter in water. It is expected that the resin which has the ability of extracting metals can be made by absorbing organic extractant on XAD-4 resin In this study, solvent impregnated resin (SIR) was produced from LIX84-I and XAD-4, and extraction and separation of nickel, cobalt and copper were conducted using SIR. The extraction properties of SIR were investigated, and a comparison between ordinary solvent extraction and SIR was made.Experimental ProcedureAmberlite XAD-4 was used as absorption resin for the organic extractant in this study. The physical properties of XAD-4 are shown in Table I. Amber lite XAD-4 has a large surface area and shows good ability to absorb organic matter in water, but the: resin does not have the ability of exchanging metallic ion."

Jan 1, 2000

By Xuewei Lv, Maojun Zhou, Xiaobo Huang, Rende Zhang

"The characterization of the surface roughness of the mineral particles is of vital importance for the studies of the mineral processing. In this study, an evaluation of the roughness of the iron ore particles, with the measurements of size distribution and the measurements of specific surface area with the liquid nitrogen absorption, was developed. The main theory of this method is the fact that the roughness of the particle influences the specific surface area apparently. The specific surface area of the particles can be measured with the laser diffraction method and the liquid nitrogen absorption method. The influence of the surface roughness of the particle can be measured with the nitrogen absorption and cannot be measured with the laser diffraction. Therefore, the roughness can be got by comparing the specific surface area with two measurement methods.IntroductionThe characterization of the surface roughness of the mineral particles is of vital importance for the studies of the mineral processing. There are three main methods for measuring the size distribution of mineral particles: sieving, laser diffraction, and sedimentationl). Many techniques involve sedimentation such as the Horiba2, 3) and the Cyclo-sizer1). In the mineral industry, size distribution is usually determined by sieving because it can be carried out accurately for all particle sizes larger than 45 . The preferred method to obtain the size distribution of finer particles is laser diffractometry. The technique has several advantages: it produces measurements in a few minutes with considerably less labor compared with the cyclo-sizer and for a range of sizes considerably wider in comparison with the sedigraph4). The equivalent-sphere size distribution reported by laser diffractometry is valid for metallurgical calculations and can be routinely used in mineral processing plants. The surface area of the particles can be measured by the BET method of nitrogen adsorption, or it can be calculated from the size distribution. However, the latter calculation requires the size distribution to be accurately known across the whole size range, and assumptions have to be made about the shapes and surface roughness of the particles and presence or absence of pores (see below). The BET method is based on the physical adsorption of gas over the whole exposed surface area and measures the surface area stemming from the roughness and open pores on the surface of the particle5). The calculation of the surface area from the size distribution is usually based on the assumption that all the particles are smooth spheres, without considering the shape and/or roughness of the particles. Determining the surface roughness of the particle with these methods, is the objective of this study."

Jan 1, 2012

By C. L. Lin

Transformation of linear grade distribution to volumetric grade distribution has been used to estimate the actual mineral liberation during wet, batch, ball mill grinding of a copper ore. The degree of liberation based on the multicomponent-multisize grinding liberation model using volumetric grade is lower than the apparent degree of liberation estimated from using King's linear intercept model.

Jan 1, 1987

By Yang Jian-guang, Deng Zi-xiang, Zhang Xu-liang, Li Jun-yuan

"Hyperaccumulator biomass harvested after heavy-metal phytoremediation must be considered as hazardous waste that should be contained or treated appropriately before disposal or reuse. As a potential method to detoxify the biomass and to convert this material to a suitable bio-energy resource, the hydrothermal upgrading process was applied to remove heavy metals and upgrading crude bio-oil from Pteris vittata stems and leaves harvest. Parameters such as material granularity, temperature, Liquid/Solid (L/S, ml/g), pressure, duration and catalysts were examined for their effect on the removal efficiency of heavy metals and upgrading efficiency of crude bio-oil. Maximum heavy metal removal efficiency of>99% and crude bio-oil upgrading efficiency of 83% were attained with an 200 mesh (75 µm) granularity, LIS 40:1and23 MPa at 380°C in the presence ofO.l mol L-1 K2C03 for 30 min. GC-MS analysis results show that the resulting bio-oil mainly consists of benzene 11 %, ketone 42%, alcohols 14%, alkene 15% and ester 11 %, etc., and the relative molecular weight distribution lies in 94-282, carbon number distribution lies in 6-18, calorific value is 32MJkg-1.IntroductionPhytoremediation of soil or water with hyperaccumulator has been extensively explored in recent years [1-4]. Living plants can clean up soils or waterways. This approach exploits the ability of various plant species to thrive in high metal environments where large amounts of toxic elements are accumulated, such as heavy metals, and is particularly appropriate when slow remediation of relatively low metal concentrations is acceptable. Advantages compared with existing remediation methods include the minimal site destruction and destabilization, low environmental impact, and favourable aesthetics; advantages compared with biosorption include continuous in situ regeneration of the biomass, and the ability of living plant cells to supplement passive sorption of metals with metabolic mechanisms of metal uptake and detoxification [5-8]."

Jan 1, 2014

By G. Taylor, S. Bounds, G. Moran, M. Cross, K. Pericleous

"A variety of interacting complex phenomena takes place during the casting of metallic components. Here molten metal is poured into a mould cavity where it flows, cools, solidifies and then deforms in its solid state. As the metal cools, thermal gradients will promote thermal convection which will redistribute the heat around the component (usually from feeders or risers) towards the solidification front and mushy zone. Also, as the evolving solid regions of the cast component deform they will form gap at the cast-mould interface. This gap may change the rate of solidification in certain parts the casting, hence affecting the manner in which the cast component solidifies. Interaction between a cast component and its surrounding mould will also govern stress magnitudes in both the cast and mould - these may lead to defects such as cracks.This paper presents a multiphysics modelling approach to this complex process. Emphasis will be placed on the interacting phenomena taking place during the process and the modelling strategy used. Comparisons with plant data are also be given."

Jan 1, 1999

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By Claudio Toro, Alex Moyano, Rodrigo Díaz, Hugo Jara, Carlos Caballero, Pedro Morales, Leandro Guzmán

"During 2007, Codelco-Chile carried out industrial tests to validate the Continuous Converting Process in the Teniente Converter of the Codelco Norte smelter.For planning and starting up the tests, a predictive, analytical and dynamic model was developed to support operational decisions. The dynamic model was developed using the METSIM® platform and dynamic data exchange (DDE) to operate smoothly with MS Excel®. The main feature of this real-time model was the on/off-line ability to work and gather data from either the smelter’s PI system® or database, and simulate the operation with or without scheduled events and controls.The main model development aspects, which include thermodynamics, metallurgical and kinetic considerations, slag-type and on-line mass and heat balances of the process, as well as the successful validation of the model, are presented and discussed in the present paper."

Jan 1, 2009

By George Nekoksa

The biofilm activity monitoring probes measure applied current during intermittent short-term polarization of the probe electrodes and current or potential between the electrodes after removal of the polarization. The probe polarization mimics conditions at crevices, welds and inclusions where the biofilm activity and microbially influenced corrosion usually concentrate. Monitoring of AC resistance between the probe electrodes can provide infornation about the thickness of deposits.

Jan 1, 1994

By G. Coryell, E. Brack

"Remaining competitive in today's metal markets requires that copper smelters utilize the latest technology offered in process control, data acquisition, and process optimization. State-of-the-art tools like minicomputers, personal computers, and microprocessor based controllers provide real time process information that assist in making proper adjustments to the overall control strategy of an operating plant. The database accumulated by such systems broaden process knowledge, thereby reducing costly errors and plant downtime.IntroductionThe ASARCO Hayden Plant is located approximately 80 miles southeast of Phoenix, Arizona. The plant was commissioned in 1912 for the purpose of smelting copper concentrates from the surrounding mining district. Copper was produced for many years using calcining, reverberatory smelting and copper converting techniques. With the stricter environmental controls of the 1970's, the smelter experienced substantial declines in efficiency and productivity. It became necessary to identify and install a new smelting technology to maintain the viability of the Hayden plant.In 1980, after evaluating several smelting techniques, ASARCO management selected flash smelting as developed by International Nickel Company (INCO). One hundred and thirty-two million dollars was allocated for the project and construction began in 1982. Construction was completed and the new plant came on line in November of 1983."

Jan 1, 1989

By Bingchen Chen, Zhitong Sui, Junwei Ma

"In the blast furnace slag, titanium disseminated in various mineral phases Titanium could be concentrated mainly in perovskite, which could be selectively precipitated and grown by optimizing the operation factors like the slag composition, temperature of heat treatment and additive agents. This study aims at establishing the titanium slag mineralogy and its distribution in the treated slag and the as-received slag, as well as the methods of perovskite separation. After heat treatment, the grain size was grown from 5 - 20µm to 80 - 200µm, the distribution of Ti02 in perovskite was increased from 48% to 81 %, the morphology was changed from snow-shaped grain to coarsening dendrites or equiaxed crystals. A concentrate were produced by gravity separation analyzing 35.25% Ti02 with a recovery of 68.28% and a tailing analyzing 9.53% Ti02 , and a possibility of flotation upgrading was discussed. I INTRODUCTION CHINA is rich in mineral resources of titanium, 92.4% of which is vanadium-titanium bearing magnetite. About 53% titanium were in iron concentrate after mineral processing, by which the blast furnace slag containing about 25% TiO2 were produced[11 • The content of TiO2 in such slag is too low to separate titanium dioxide, and it is also too high to produce slag cement[21. It has been accumulated to 50 million tons so far, which is still increasing at a rate of 3 million tons per year, and results in a waste of titanium resources and pollution of environment. Due to the dispersed distribution of titanium component in various mineral phases, very fine grain(<10µm) and complex interfacial combination, it is very difficult to recovery titanium component from the slag by traditional separating technique. In this paper, a novel technique to recovery titanium from the waste slags was proposed [3H4l, on which three continuous processes were involved: selective concentrating, selective growing and selective separating. Perovskite was designed as a titanium-rich phase, in which the most titanium was concentrated promptly, then perovskite could be selectively grown and coarsened by optimizing the heat treatment and the appropriate additives [ 5l[6l. The grain size of perovskite phase was larger than 80 µm, and the crystals appeared as coarsening dendrites or equiaxial grains like lump."

Jan 1, 2000

By R. Kramer

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the. foundry, the sand was examined in detail Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1991

By Norbert L. Piret

From the copper smelter operation a various outputs are to exert negative impacts on the environment. Particularly, emissions like SO2 and dusts, solid wastes like contaminated gypsum and arsenic sludge, effluents and heated cooling water are generated. Most countries have sitipulated an environmental legislation to provide the framework for an efficient environmental management. As part of the planning activities for x major greenfield copper smelter, the Following elaborations are required and were drawn up. -The Environmental Impact Assessment which is the first step of environmental management and mandatory for every new project. - The Environmental Monitoring Plan, which describes the monitoring procedures for the main impacts identified and assessed. -The Environmental Management Plan, which deals with the minimization of environmental impacts, and the methods of its implementation.

Jan 1, 1996

By U. Kammer

The reduction of the lead content in the separator fraction produced during the mechanical processing of spent lead-acid batteries is an important environmental and economical issues. The reduction of lead down to less than 1 percent is very difficult using hydroseparators that are common in battery recycling facilities. Very promising results were achieved performing experiments on a test rig using a new technology in battery treatment: a discharge-type jigging unit. The materials is fed onto the jigging bed and transported through the machine. Due to the intensive movement of the feed, an additional washing effect is also obtained in addition to separation of the lead and plastic fractions. The knowledge gained from this development work at UVR-FIA GmbH in Freiberg, Germany, led to a patent application. This paper focuses on the results of the development work and the start-up and one year's operation of the industrial-scale application at Harz-Metall GmbH in Goslar, Gennany.

Jan 1, 2000

By Shengqi Chen

The reduction smelting of nickel laterites produces slag, consisting principally of the chemical components MgO, "FeO", SiO2, and A12O3, and ferro-nickel alloy. Despite the fact that the phase equilibria for the ternary MgO-"FeO"-SiO2 up to 1500°C is well established limited experimental data are available in the MgO-"FeO"-SiO2-Al2O3 system, which is relevant to commercial operation of the process. A methodology has been developed for the experimental investigation of the liquidus temperatures for the multi-component system MgO-"FeO"-SiO2-Al2O3-Cr2O3 in equilibrium with metallic iron. Experiments have been carried out using high temperature equilibration, quenching, followed by electron probe X-ray microanalysis (EPMA). Liquidus temperatures have been determined in the silica primary phase field in the composition ranges directly relevant to the Cerro Matoso S.A. ferro-nickel smelting slag. Liquidus isotherms have been determined for temperatures between 1450 to 1600°C. The study enables the liquidus to be described for a range of MgO/FeO ratios. It was found that liquidus temperatures in the silica primary phase field decrease significantly with the addition of AI2O3. Keywords: Liquidus temperature, ferro-nickel, pyrometallurgy, smelting

Jan 1, 2004

By Adam J. Gesing

The eddy current separator (ECS) is designed to separate nonmagnetic (nonferrous) electrically conducting (metallic) particles from nonconductive residue. Nonferrous metallic particles are repelled out of the material stream passing over the eddy current rotor (ECR). The rotor is housed in a fiberglass composite outer shell that serves as a conveyor head pulley. This results in the desired metaVnonmeta1 separation. The behavior of ferromagnetic particles, mainly iron and iron oxide (i.e. rust), is quite different. These particles are strongly attracted to the magnets and the smaller particles tend to align their long axis in the direction of the magnetic flux. Since the direction of the flux changes with the passage of each magnet pole, the small particles spin at very high rates causing wear of the belt and of the composite outer shell housing the ECR. Large particles, when trapped under the ECS belt, cannot spin, but can be heated by the eddy current effects and subsequently can burn through the composite outer shell. We discuss the practical implication of this behavior of iron and rust on the design, performance and maintenance of eddy current separators.

Jan 1, 1999

By C. S. Ek

Tests have been performed to recover silver and lead from residues produced after a super-hot leaching in a zinc hydrometallurgical plant operating with jarosite precipitation. When this residue is leached in ammoniaammonium sulfate or in diethylenetriamine solutions, lead dissolution is not complete and its recovery from the aqueous solutions is either difficult, due to the operating conditions, either expensive due to the amount of added reagents. In both cases, silver is partly dissolved, partly left in a new residue still containing lead and baryum sulfates. The best treatment seems to include a selective flotation producing first a silver concentrate assaying about I % Ag, then a 50 % lead concentrate collecting the baryum salts, and a final quartz-gypsum tailing. Metal recoveries can reach 50 % and 80 %, respectively.

Jan 1, 1989

By William Petruk

The Kidd Creek base metal deposit near Timmins, Ontario contains around 0.15 wt% Sn, mainly as cassiterite. The cassiterite occurs largely as inclusions in sphalerite, with 85% being in grains smaller than 18.5 micrometres in diameter. Concentrates and tails from the company&apos;s Cu, Pb and Zn circuits were studied to determine the liberations and recoveries of cassiterite in the products. The ore had been ground to about 65.% minus 44 micranetres in diameter (-325 mesh); 55% of the cassiterite was liberated. About 92% of the liberated cassiterite and 70% of the unliberated cassiterite were in the concentrator tails, and 20% of the unliberated cassiterite in the zinc concentrate. The company had attempted to recover the cassiterite from the concentrator tails by gravitational methods but recoveries were low. The grain size of the cassiterite in the gravity Sn concentrate was similar to the grain size of the liberated cassiterite in the concentrator tails. Research on flotation of the fine grained cassiterite from Kidd Creek ore has been conducted,

Jan 1, 1990

By C. D. Chapman

Current regulations regarding the landfill disposal of asbestos containing wastes are inadequate to ensure there are no ground water or airborne emissions. Accordingly, there is growing recognition that asbestos wastes can only be safely disposed of by using techniques that destroy the hazardous fibres. An innovative high-temperature plasma arc technology (The MAGRAM Process) is being developed for the recovery of magnesium metal from asbestos together with supplementary magnesia containing feedstock. The furnace will operate in. open bath mode with aluminium and/or ferrosilicon being employed as reductant. An important advantage of the process is that magnesium vapour within the furnace will be generated close to atmospheric pressure rather than at reduced pressure under which existing processes operate. Thermodynamic modelling work has been undertaken to define the range of slag composition and furnace temperature under which magnesium production at atmospheric pressure is feasible. The effect of slag chemistry, reductant addition, and temperature on product quality and yield have also been investigated and key aspects have been tested on bench scale. A 300 kW pilot plasma furnace unit has been employed for the treatment of calcined asbestos wastes. Aspects of design and operation of the unit are detailed. Acknowledgement: This work is substantially financially supported by the European Communities under the Industrial and Materials Technologies (Brite EuRam H) Research and Development programme.

Jan 1, 1995

By D. Bruce Wilson

The reaction of oxygen and solid aluminum produces the well-known surface coating of aluminum oxide, Al2O3. Thermodynamic properties and kinetic mechanisms of this reaction are extensively documented. Less well-defined are the corresponding liquid phase reaction and reactions which would be characterized. as &apos;burning&apos; of aluminum. This paper reviews the solid aluminum-oxygen reaction as a foundation for discussing the flammability of aluminum in oxygen-enriched atmospheres. Appropriate thermodYDan3ic analysis and kinetic reaction mechanisms are developed. Available models of aluminum burning are reviewed and evaluated, The appropriate information for design of engineering applications of aluminum in oxygen atmospheres? is summarized.

Jan 1, 1996

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989