Search Documents

By Alicia Esther Ares

This study was conducted to investigate the directional solidification of Zn-20%A1 and Zn20% A1-1O%Si-3o/oCu alloys under different conditions of heat transfer at the metal/mould interface. The type of structure obtained in both cases was analyzed and related to the solidification thermal parameters such as cooling rate, growth rate, thermal gradient and recalescence which were determined from the temperature versus time curves. These parameters were correlated with the structure-like length of columnar grains and size of equiaxed grains. The metallographic analyses were done performing quantitative metallography and composition analysis of the different alloying elements along the cast samples by SEM (Scanning Electron Microscopy) and EDXA (Energy Dispersive X-Ray Analysis). Correlations between properties, structures and thermal parameters were found.

Jan 1, 2008

By D. W. Ashman

The zinc pressure leaching plant at Cominco's Trail Operations is now in its ninth year of production. The plant produces a zinc sulphate and jarosite slurry which is further processed in the calcine leaching circuit. Elemental sulphur, a by-product of the process, is sold in the North American market. During the past eight years, a number of changes have been made to the plant to remove known production bottlenecks and to improve leaching extraction. These changes have raised production rates above the initial design so that the plant currently accounts for approximately 20 percent of Trail s zinc production. These rates are expected to be increased further upon the completion of the alterations currently in progress. The knowledge gained over the operating life of this plant has allowed Cominco to plan for a possible future expansion of the zinc pressure leaching plant. If expanded, zinc pressure leaching would account for approximately 48 percent of cominco?s zinc production.

Jan 1, 1990

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By Hoda Emami

In this study, a combined pyrometallurgical and hydrometallurgical technique has been designed and used to recover rare earth mixture elements (REE) and cobalt from a NdFeB magnetic waste. while addressing the cost of reagent and process facility. This process can be adjusted to different magnetic wastes regardless of their compositions. Prior to the leaching, the magnet scrap was pretreated by two rounds of roasting (750°C in air) and a mechanical grinding in between, to convert iron metal to ferric oxide. Subsequent leaching was performed using optimized conditions (pH, temperature and retention time) where the extraction ratio of REE to Fe III is the highest. After removing iron content from the leachate (pH ≈ 3), REE was precipitated selectively and purified further. The produced REE concentrate reaches 99% purity with 85% recovery in a single run. The cobalt oxide was isolated from the PLS as a by-product with 99.8% purity.

By R. Togashi, T. Aichi, T. Yamada

"A new automatic material- handling system for cathode transportation has been developed. The first system went into service in August 1994 and the remains will be operational subsequently.Because of the complex cell-layout and the number of cells in each row, the critical part of this work was achieving a planned cycle time. This cycle time is determined by the power costs.The central monitoring system for machine operation was started in June 1996, using original application software based on MICROSOFT EXCEL ® on WINDOWS 95® .As a result, only one person is now required to operate both a crane and a stripping machine for one row of about 50 cells.INTRODUCTIONMainly due to the strong yen and the relatively low price of metal, the zinc refineries in Japan are being forced to reduce production costs again and again.The trend of lijima's production costs is shown in Figure 1.[1] The ratio of labor costs becomes gradually higher. Therefore it is effective to reduce the labor costs in order to reduce the production costs. In Japan, electricity cost during day time is too high to produce zinc at a reasonable cost, that is why the actual production is far from the capacity of production at a cell house. That means a plant in Japan has the disadvantage of relatively low productivity for cell house operation.Saving labor costsSome automatic cranes have been applied to save labor costs for cell house operation in the world. In consideration of the mentioned low productivity, the installation of an Automatic Cathode Transfer (ACn system for transportation of cathodes was planned without changing the present cell house and stripping machines to lower the investment costs. The ACT system must keep up with the stripping machine which is able to strip deposit zinc from a cathode sheet at the rate of 6 seconds.The fifth ACT system of seven was installed in August 1996 and the last one will be operational subsequently."

Jan 1, 1997

By J. E. Dutrizac

The behaviour of the lanthanide elements during the precipitation of sodium and potassium jarosites at 98oC from sulphate media was systematically investigated. The lower atomic weight lanthanide elements (La to Gd) are characterized by the limited solubility of their alkali-lanthanide sulphates, such as NaNd(SO4)2?H2O, which commonly contaminate the jarosite precipitates. Hence, single phase jarosite-type compounds were precipitated only from solutions containing <0.4 g/L of the La to Sm lanthanides. The sulphates of the heavier atomic weight lanthanide elements (Tb to Lu) have significantly higher solubilities such that solutions containing up to 10 g/L of the individual lanthanides could be investigated without the precipitation of alkali-lanthanide sulphate species. Even at the highest lanthanide concentrations, however, none of the jarosite precipitates incorporated more than 0.3 wt% of any of the lanthanide elements. Comparable levels of lanthanide incorporation were noted in both Na-jarosite and K-jarosite. Although the mass of the jarosite precipitate increased with increasing ferric sulphate concentration or with increasing pH, the extent of lanthanide incorporation was not significantly affected. Clearly, the trivalent lanthanide elements do not substitute extensively for trivalent iron in the jarosite structure. This behaviour likely reflects the significantly lower hydrolyzability and larger size of the trivalent lanthanide ions relative to ferric ions.

Jan 1, 2003

By K. Osseo-Asare

"The molecular structural and solution chemical characteristics that underlie the surface activity of solvent extraction reagents are highlighted, with particular emphasis on the tendency towards reverse micelle and microemulsion formation. The physicochemical factors that lead to microemulsion-enhanced solvent extraction with chelating extractants are elucidated. Membrane-based contactor systems are described which are uniquely suited for enhanced solvent extraction with microemulsions. The possibility of combining solvent extraction with microemulsion-mediated materials synthesis is discussed. IntroductionThe discovery of new selective extractants has resulted in major breakthroughs which have helped to establish solvent extraction as a versatile separation technology (1-3). A complementary strategy towards new process development is to seek new ways of using the available reagents. This paper explores this second approach. From a molecular structural standpoint, an extractant may be viewed in terms of two components: a polar functional group and a hydrocarbon radical. In the conventional view of solvent extraction, this molecular structure serves two main purposes: The polar functional group provides the binding sites for complexation of metal ions, while the organic group is needed to render the resulting metal-extractant complex organic-soluble. But are these the only properties of the organic and the polar groups that are relevant to the solvent extraction process?In this paper, attention is directed to the fact that solvent extraction reagents possess the molecular structures of amphiphiIes; that is, they are characterized by the presence of spatially separated hydrophilic and hydrophobic groups on the same molecule. A case is made for the view that this amphiphilicity offers interesting opportunities to develop new separation processes which collectively may be described as enhanced solvent extraction (4-6)."

Jan 1, 1996

By Peter Olubambi, Babatunde Obadele, Oluwagbenga Johnson

"The microstructure and corrosion behaviour of titanium carbide (TiC) reinforced duplex stainless steel matrix surface composites synthesized by laser melt injection technique was investigated. The surface melting operation was conducted using a 4.4 kW CW Nd:YAG laser with laser power of 1.5 kW, scanning speed of 0.4 to 1.0 m/min, beam size of 3 mm and argon shield gas flow rate of 4 L/min. The morphologies and microstructures of the coatings examined using field emission gun scanning electron microscope (FEGSEM) revealed homogeneous distribution of fine precipitates of TiC in the matrix, while X-ray diffraction (XRD) analysis confirm no phase change. TiC addition to the steels significantly increased hardness value to about 547 Hv0.1 but slightly decreased the corrosion resistance of the steels in 3.5% NaCl possibly due to the intergranular carbide coating that prevented chromium from forming continuous passive oxide layers.IntroductionComposite materials evolve from the idea of combining two basically dissimilar materials with different physical and mechanical properties to arrive at a product whose final properties are superior to those of the individual components [1]. Metal matrix composites (MMCs) are receiving much attention and are the focus of intense research and development worldwide for aerospace, automotive and other applications because of their excellent combination of ductility and toughness of the metallic matrix with high hardness and strength of carbides reinforced in the matrix [2]. Surface modification techniques such as laser, thermal spray, plasma spray, chemical vapour deposition have been use to fabricate MMCs. Laser melt injection (LMI) is a surface modification technique known since the 1980s [3] has been used to improve surface properties of metallic alloys such as aluminium, titanium and steels [4-6]. It involves the lateral injection of carbides, ceramics and cermets blown by a gas stream into a liquid metallic pool, created by laser irradiation of the top surface of the base material."

Jan 1, 2012

By Tadashi Aiura, Yasuhiro Miura

"A small amount(0.2mass%) of Scandium(Sc) was added to the 7.NOl and 5083 Al alloys as a refiner and stabilizer of microstructure, and the resulting microstructures were discussed in comparison with the effects of the conventional additives. The followings are summarized: 1) in the as-solidified structure, a ·decreased tendency of constitutional supercooling and increased solubility of Mg were recognized for the Sc-added 5083 alloy. Sc is a -better microstructure refiner for the 7N01 alloy than Zr, in a sense that it does not suppress the favorable effect of· coexisting Ti. 2) Sc effectively suppresses recrystallization both in the 5083 and 7N01 alloys. 3) The rod like primary Al3Sc crystals formed during solidification, as well as the fine dispersion of Al3Sc precipitates formed by subsequent heat treatment, can act as a strong recrystallization suppresser. IntroductionThe 7N01 and 5083 alloys are the most popular industrial Al alloys and they are widely' used for various structures because of their superior properties. Fine macro and micro structures of the materials are required for obtaining acceptable sec resistance,consistent appearance of anodized surface and good weldability, as well as good mechanical properties. In order to produce fine grain structures, transition metals, such as Cr, Zr, and Mn, have been conventionally added.It has been reported that Sc is an efficient refiner [l, 2] and can be an alternative for the conventional and also suppresses recrystallization in Al alloys [3,4]. Scandium is the lightest transition element and forms an equilibrium intermetallic phase. The equilibrium phase, Ll2-Al3Sc, is coherent with the matrix, and of _spherical shape. A fine dispersion of the spherical precipitates is obtained by quenching and aging after solutionizing annealing. The authors have already reported a part of the experimental results on the effect of Sc on the as homogenized microstructure of the 5083 alloy [5]. In the present study, the effects of Sc on the macro and micro structures of the industrial high strength Al alloys(7N01 and 5083) for extrusion are investigated, and the superior role of Sc as a grain refiner is shown"

Jan 1, 2000

By Miao Tian

Large quantities of copper complex resources are produced globally and urgent to be cleanly processed. This article presents a thermodynamic analysis of mixed smelting process including low-grade polymetallic copper sulfide concentrates, high copper content sulfide concentrates, metallurgical by-products (copper removal slag from lead metallurgy), and copper powder from electronic waste. A top blown smelting reactor to simulate mixed smelting process is developed using a metallurgical process simulator, METSIM. Reactor parameters, heat loss and phase distributions are estimated from actual plant data. The proper proportion between complicated primary and secondary copper resources is determined by analyzing the influence of the feed rates of various resources, oxygen, silica flux and revert on the smelting performance. Autogenous smelting process is built by optimized matching materials of copper complex resources, in terms of the reactor temperature, copper content in matte and slag, and the percentage of magnetite in slag.

By Ruiling DU, Jiazhi Zhang, Yong Zhao, Keng Wu

Reaction kinetics of metallurgical physical chemistry which was successfully applied in metallurgy (as ferrous metallurgy, non-ferrous metallurgy) became an important theoretical foundation for subject system of traditional metallurgy. Not only the research methods were very perfect, but also the independent structures and systems of it had been formed. One of the important tasks of metallurgical reaction engineering was the simulation of metallurgical process. And then, the mechanism of reaction process and the conversion time points of different control links should be obtained accurately. Therefore, the research methods and results of reaction kinetics in metallurgical physical chemistry were not very suitable for metallurgical reaction engineering. In order to provide the definite conditions of transmission, reaction kinetics parameters and the conversion time points of different control links for solving the transmission and reaction equations in metallurgical reaction engineering, a new method for researching kinetics mechanisms in metallurgical reaction engineering was proposed ,which was named stepwise attempt method. Then the comparison of results between the two methods and the further development of stepwise attempt method were discussed in this paper. As a new research method for reaction kinetics in metallurgical reaction engineering, stepwise attempt method could not only satisfy the development of metallurgical reaction engineering, but also provide necessary guarantees for establishing its independent subject system.

Jan 1, 2015

By Sergio Sanchez-Segado, Yuan Zhang, Animesh Jha, Ahmad Fahmi Ruzaidi

Niobium and tantalum are considered critical materials because the increasing demand in the energy sector which is reliant on limited abundance of these two metals in minerals. Traditionally, niobium and tantalum mineralsare digested using hydrofluoric acid at moderate temperatures, producing oxy-fluorides which are separated by solvent extraction, involving the use ofhazardous chemicals. The increasing environmental pressures are forcing the industry to search for alternative low carbon processing methods. In this paper alkali roasting based separation and beneficiation, which is not well understood in the literature, is proposed, for which the kinetics and thermodynamic equilibria for the formation of sodium tantalate and niobate with sodium hydroxide are analyzedat the temperature range of 400ºC to 700ºC. The apparent activation energy of formation,changes from 31.0±0.8 to 22.3±1.2 kJ mol-1 and from 23.8±1.2 to110.2±12.8 kJ mol-1, for tantalate and niobate, respectively. The reaction mechanism is examined on the basis of the analysis of reaction products using X-ray powder diffraction (XRPD) and X-ray fluorescence (XRF).

Jan 1, 2015

By J. E. Allen

The trend in refractory technology for the copper and nickel industries has been to higher quality raw materials and improved processing technology. These changes have been dictated by the changes in pyrometallurgical processes in these industries. For example the introduction of flash smelting, reaction type smelting and auxiliary slag cleaning furnaces havedemanded better refractories materials. Extensive field applications and improved laboratory testing procedures have helped make this transition possible. Changes in refractory technology, primarily in basic refractories, are followed from the late fifties to the present and into the future.

Jan 1, 1994

By J. Daniel Bryant

Deformation processing of rapidly solidified powder alloys presents a technical challenge different in several ways from the processing of ingot based alloys. The metastable phases formed during planar flow casting of aluminum alloy 8009 (FVS0812) must be safe-guarded from high temperature excursions during processing to avoid decomposition; this restriction prohibits liquid phase sintering of particles during consolidation. The development of strong particle-particle adhesion, therefore, relies on the imposition of very large strains during forming operations to insure sufficient mechanical meshing of the aluminum particles and break-up of prior particle oxide boundaries. These strains are generally much greater than those required for metallurgical transformations in ingot based alloys. In an attempt to quantify the deformation required to improve interparticle bonding, the finite element method (FEM) was employed. Preliminary results which predict the metal flow and strain distribution in several workpiece configurations are discussed. These predictions are then correlated to measurements made on experimental subscale forgings. Lastly, experimentally measured quantities which reflect the degree of interparticle bondingg are related back to FEM model predictions.

Jan 1, 1992

By Wenjun Duan, Zongliang Zuo, Qingbo Yu, Qin Qin, Junxiang Liu

Moving bed has been widely used in the field of heat and mass transfer and reaction between solid particles and gas. In order to enhance the heat exchange coefficient, there will be tube banks inserted in the moving bed. In the process of drying ammoniates particles or heat recovery from high-temperature particles with moving bed, the particles flow behavior around the tube banks is significant. In this paper, the particles flow behavior around the tube banks is investigated, and all the results can provide guidance for the design and operation of a moving bed.

Jan 1, 2016

By Jayagopal Ucbil, M. Krishna, V. T. Vijayalakshmi

"The pitting susceptibility of aluminium metal matrix composites reinforced with garnet particles has been examined using static weight loss method by exposing the metal matrix composites (MMC) specimens to the action of IN HCI acid at laboratory temperature for different time intervals. It was found that the corrosion rate decreased with increase in weight percentage of reinforcement while the corrosion rate was a function of the matrix alloy but not of the reinforcement material. Further, it was found that the rate of corrosion was dependent on the interface region formed between the reinforcement and the matrix. A comparison of the base matrix with the corresponding composite when subjected to heat treatment for varying periods of 4, 8, and 12 hours respectively was made. The comparison revealed that corrosion resistance of the composite increased with the duration of heat treatment and this has established a considerable improvement in corrosion resistance of the composite when compared with the base matrix.IntroductionMetal matrix composites (MMCs) offer designers many added benefits, as they are particularly suited for applications requiring good strength at high temperature, good structural rigidity, dimensional stability, and light weight [1-5]. The trend is towards safe usage of the MMC parts in the automobile engine, which work particularly at high temperature and pressure environments [6-7]. Particles reinforced MMCs have been most popular over the last two decades. Among the MMCs, the most popular families are represented by aluminium reinforced with ceramic particles. Although the incorporation of the second phase into a matrix material can enhance the physical and mechanical properties of the base metal, it could also significantly change the corrosion behavior."

Jan 1, 2000

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Onsan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Ousan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By Dean Ilievski

Mathematical modelling of the precipitation process requires that the kinetics of crystal growth, nucleation and agglomeration be known: This paper reviews the current state of knowledge on these precipitation sub-processes (ie. growth, nucleation and agglomeration) and describes a number of experimental techniques for estimating their kinetics. The experimental methods used to generate the precipitation data and the data analysis techniques used to extract the kinetics information from the data are discussed separately. There is no universal "best" technique for determining the kinetics. However, studies on multi-crystal systems are more reliable for modelling purposes than are single crystal studies. The selection of a technique will depend on which sub-processes are present. A problem with all kinetics studies is that there is generally a large uncertainty in the estimated kinetic parameters. This stems from the scatter in the experimental data being further propagated by the mathematical techniques used to extract the kinetic parameters.

Jan 1, 1996

By Mehdi Asgharifar, Rouzbeh Sarrafi, Radovan Kovacevic

"The surface treatment of aluminum alloys using atmospheric-pressure of low intensity DC plasma arc discharge is investigated in terms of surface properties. With respect to the conventional surface treatment processes for aluminum alloys mostly based on chemical etching or sand blasting, this process is very environmentally friendly and cost-effective. The effect of two processing parameters, the current and the plasma torch scanning speed, on the surface morphology is studied by using a scanning electron microscope. The effects of cathode spots within the tested range of process parameters are determined, and the limiting factors of the process (such as surface cracking) are discussed. The topographical studies of the treated surfaces have suggested potential enhancement of surface properties for different applications, such as preparing surface for painting and adhesive bonding.IntroductionIn the last decade the aluminum alloys are finding broad applications in automotive industry. In order to successfully execute the joining process of aluminum alloys such as arc welding, laser welding, and adhesive bonding, there is a need to remove oxides for welding and texture the surface for bonding along the join line. A number of surface treatment techniques such as chemical etching, sand blasting, and plasma treatment have been used by industry. It is shown [1] that plasma surface treatment is characterized as environmentally friendly, lower cost, and easier to control process. Bogaerts et al. [1] mention that when an adequately high potential difference is applied between cathode and anode, electrons are accelerated toward anode by an electric field coming in collision with gas atoms. The gas breaks down into positive ions and electrons, giving rise to gas discharge. The DC electrical discharges used in industrial plasma sources can be related to their location on the voltage-current curve as shown in Figure 1.It is generally believed that dark discharges other than coronas, and arc or torch plasmas are not very good candidates for surface treatment because oflow or high power density and active species flux. However, the glow discharge plasma is used for plasma surface treatment applications because of its proper power density and active-species flux [2]. Our objective is to investigate the feasibility of using low intensity DC plasma arc discharge as a surface treatment method without damaging the cathodic non-thermionic workpiece."

Jan 1, 2011