Search Documents

By Jeramy B. Decker, Paul H. Madsen

"During the excavation of the north bound tunnel of the Devil’s Slide Tunnel project, deformation (convergence) was measured after passing through Fault Zone B. The tunnel convergence was not symmetrical, but was larger on the left side of the profile. It was determined that a shear zone nearly parallel with the tunnel drive was contributing to the uneven deformation. This paper will discuss how it was determined that the shear zone existed and how multi-point borehole Extensometers (MPBX) were used to verify that a significant amount of the deformation was occurring due to movement along the shear zone as the excavation was advanced. In addition, performance of the shotcrete liner in the area of the convergence will be examined. Finally, the paper will consider the means and methods that were utilized to ultimately control and stabilize the deformation. INTRODUCTION The Devil’s Slide Tunnel Project consisted of excavating two 1,250 meter tunnels each with a profile of 80 m2 utilizing the New Austrian Tunneling Method (NATM) or otherwise known as the Sequential Excavation Method (SEM). The tunnels are part of the California Coastal Highway south of Pacifica, CA, a suburb of San Francisco. The tunnels were opened to traffic in March of 2013. Geological Setting The tunnels run north-south through the San Pedro Mountain ridge, which is part of the Santa Cruz Mountains. The tunnel lies within the San Andreas Fault system and is 7.2 km west of the surface trace of the San Andreas Fault and 2.8 km east of the surface trace of the San Gregorio Fault. The 10 km strip between these two faults is referred to as the La Honda structural and terrain block (Decker et al. 2010; Amini et al. 2005; Earth Mechanics Inc. 2003). Locally, the tunnel passes through three blocks representing different geological conditions: South Block, Central Block, and North Block (Figure 1) (Decker et al. 2010; HNTB Corporation et al. 2005). The South Block consists of Mesozoic aged granodiorite and quartz diorite. The South Block also contains many local shear zones and a low angle thrust fault (Fault A). The South Block ends at Fault B, which is the southern border of the Central Block."

Jan 1, 2016

By George A. Komadina

The Pima Mining Company lies 20 miles southwest of Tucson, Arizona, and some 45 miles north of the Mexican border. The mill is situated on a hillside overlooking Tucson and the Santa Cruz Valley, the ground generally sloping northeast at a 2.5 percent grade. The hillside location allows for gravity flow generally through the plant as well as for: tailing disposal.

Jan 1, 1965

By John MacDonald

An unstable economy has shown businesses what the mining industry has known for decades ? a successful business location today may not succeed in the future. Unexpected expenses, natural events and workforce changes have a big impact on the costs of production. To help focus production and maintenance budgets, mining executives are increasingly turning to production metrics to make key decisions. Role of mine and mill data Companies employ a variety of information systems to allow employees to accomplish their operational tasks, and each worker is focused on the metrics, or key performance indicators (KPI), for his or her individual function. For example, machine operators monitor throughput and cycle time to keep the machines running continuously and to meet daily production quotas. Meanwhile, the maintenance teams monitor machine performance, overall equipment effectiveness (OEE) and meantime between failure to predict and help prevent downtime.

Jan 1, 2013

By Jim Gebhardt

Douglas W. Fuerstenau (DWF) grew up on a farm and in several small communities in rural South Dakota during the depression years, where he learned the value of hard work. Working hard can produce results but being clever and hardworking will give you a bright future. In his later school years, Fuerstenau’s family moved to Rapid City where his intellectual curiosity and capacity helped him graduate with a B.S. in Metallurgical Engineering from the South Dakota School of Mines and Technology in 1949. His technical interests led to graduate studies and completion of a master’s degree from the Montana School of Mines in 1950 and Sc.D. degree from the Massachusetts Institute of Technology (MIT) in 1953.

By Greg Beckstrom

Minnesota is a major mining state. This statement is not a dream or stretch goal but is a fact. As reported in a recent edition of Mining Engineering magazine, Minnesota ranks as the third largest state in terms revenues generated from nonfuels mineral production. The vibrancy of the mining sector in Minnesota can be attributed to several factors. The northeastern corner of the state is home to Minnesota?s iron range, one of North America?s largest deposits of iron ore. Iron ore from Minnesota is a strategic resource that has been [ ] instrumental to the nation?s development ? 90 percent of the iron used to build ships and planes during World War II came from Minnesota. Taconite pellets now produced from openpit mines on the iron range are shipped to steel mills worldwide. The growing appetite for steel in China and India has reignited once moribund mining operations throughout the iron range.

Jan 1, 2012

By Meghan Murphy, Yiming Sun, Kush Chohan

DTX is a 1.3-mile-long rail extension being constructed by Transbay Joint Powers Authority to extend Caltrain rail service and future California High Speed Rail service to downtown San Francisco. It includes a 3,352-foot-long mined tunnel with a cross section varying from 50 to 60 feet wide and 43 feet high to accommodate two- and three-rail tracks. DTX will be excavated in mixed-face and Franciscan Formation with ground cover ranging from 40 to 85 feet. This paper discusses how mined tunnel design has evolved since the initial preliminary design phase over 10 years ago. The current design concept for tunnel construction is also discussed.

Jun 13, 2023

By D. W. Hendrickson

Cliffs views the process as extending from mine planning to cargo loading including auxiliary systems such as material handling and plant utilities. Process automation is recognized as an area that can provide significant improvement opportunities with less capital requirement than major flowsheet modifications. This paper discusses the development and results of a strategy to allow and promote implementation of process automation improvements at individual mines based on their economic priorities taking advantage of common systems and concepts for use at multiple mines where practical. Specific process control upgrade projects a Hibbing Taconite Company and the Empire Mine are reviewed in detail.

Jan 1, 1998

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By David Humphreys

Assumptions about future commodity prices need to be made with close regard to the purposes for which they are being used. Prices generated for financial planning or trading purposes are unlikely to be suitable for the longer run purposes of project evaluation and reserve estimation. In this latter context, price assumptions need to be realistic, stable and rooted in a rigorous fundamental analysis of long run industry drivers. Amongst the factors to be considered in such analysis are price history, production costs and structural dynamics. It is also important that prices adopted are consistent with other information being used by a company in its decision-making.

Jan 1, 2003

By E. Fahrenkrog

An intelligent supervisor developed using expert system tools and applied to a crushing plant is presented in this paper. The structure of this supervisor, based on a model of a human operator, consists of a Knowledge base containing a qualitative model of the process, and a Rules base with the heuristic logic used by an operator when supervising a plant. The simulation results obtained show the potential of this type of systems to supervise the automatic operation of a plant.

Jan 1, 1989

By R. E. Gertsch

A mobile-modular carbon adsorption mill design and operation for small to medium sized heap leach precious metal mines is presented. In the mobile-modular strategy, charcoal columns with adsorbed metal move from small strategically located carbon adsorption loading stations to a central stripping facility and back. The design has many advantages: 1) It scales-up from pilot plant to full production. 2) It has low capital requirements. 3) Operational costs are competitive with other systems. 4) Mill production can react quickly to changes in ore grade or property area. 5) The solution circuits are simple and easy to maintain. 6) Charcoal damage is reduced.

Jan 1, 1993

By B. H. Kim, S. J. Schatzel, K. M. Ajayi, G. S. Esterhuizen, D. W. H. Su, Z. Khademian

The stability of shale gas wells drilled through current and future coal reserves can be compromised by ground deformations due to nearby longwall mining. Depending on the longwall-induced rockmass permeability, the high-pressure explosive gas from the damaged well may reach mine workings and overwhelm the mine ventilation systems. This study uses geomechanical models to estimate the rockmass permeability induced by mining. A two-panel longwall model of a deep, 341-m-cover mining site in southwestern Pennsylvania is constructed in 3DEC to explicitly model the rockmass by a Discrete Fracture Network (DFN) technique. Stress-induced fracture apertures and permeabilities are calculated across the model and are validated against permeability measurements. A Fracture Flow Code (FFC) is developed to use these results to predict potential inflow to the mine should a gas well breach occur. One hundred DFN realizations are simulated, and the results show that for a gas pressure of 2.4 MPa, the average of the predicted inflow rates to this deep-cover mine is 0.03 m3 /s, significantly lower than the average inflow of 0.92 m3 /s for a shallow-cover mine (145 m deep) studied in the previous work (Khademian, et al. 2021). The result can help assess the potential hazards of a shale gas well breach for mine safety and evaluate the ventilation requirements to mitigate the risk

Mar 2, 2022

By Alan J. Michaels

The paper addresses the problem of the high costs of accidents ad how AMAX Inc. - a diversified natural resources company - has managed to control its losses through a tri-thrusted approach of: (1) management commitment, (2) methods of implementation that are tailored to each division or local unit, and (3) a reward system for outstanding performance. Specific attention is focused on the Corporate Loss Prevention Department's "10 Point Program for Loss Prevention Management".

Jan 1, 1981

By M. J. DeJong, R. J. Mair, S. Ritter, G. Giardina

"For urban tunneling projects it is essential to predict and prevent building damage. Although various case studies and experiments have shown that buildings considerably modify greenfield soil movements, widely accepted damage assessment methods neglect this soil-structure interaction and simplify structures as linear elastic beams. This paper summarizes an experimental investigation of the response of more realistic structures to tunneling-induced deformations. Small scale structural models with façade openings and brittle material properties were 3D printed and tested in a geotechnical centrifuge. Soil and structure displacement data were obtained by image-based measurement. Results demonstrate that structures notably mitigate differential greenfield ground displacements. It is also shown that maximum soil settlements, horizontal soil displacements beneath the structure and structural damage in the form of cracking significantly depend on the position of the structure in the settlement profile. The results provide a basis from which to predict building settlement response with greater certainty. INTRODUCTION With continuing population growth and increasing urbanization expected in the next decades, there is an urgent need for a next generation of infrastructure. It is likely that a large part of this infrastructure will be underground. Such creation of urban underground space frequently involves the excavation of shallow tunnels in close proximity to existing structures and utilities. For example, along the Crossrail project in London more than 1,200 structures are located within a possible influence area of the tunnel construction (Torp-Petersen and Black 2001). The assessment of building damage plays a vital role throughout the planning, design and construction stage of urban tunneling projects. However, while predictions of tunneling-induced deformations in the greenfield can generally be made with some confidence, much uncertainty exists about how structures interact with ground movements arising from tunnel construction."

Jan 1, 2016

By Earl Parker

The mining/mineral processing industry constantly faces the challenges of handling tons of material in a variety of processes such as crushing, milling, drying, belt transfer and loadout. These processes result in the production of high volumes of dust. A variety of dust detection and collection equipment is needed to properly manage these emissions to remain compliant with stringent air quality and safety requirements. Dust monitoring and bag leak detection can provide ways to reduce air pollutants, make work environments safer and remain compliant with requirements from the U.S. Environmental Protection Agency (EPA), U.S. Mine Safety and Health Administration (MSHA) and U.S. Occupational Safety and Health Administration (OSHA). There are several approaches to monitoring particulate emissions from dust collection equipment. These can include visual inspections, differential pressure gauges or bag leak detection systems. Bag leak detection and monitoring systems can be optical, light based or electrostatic/triboelectric. Recent developments have advanced the efficiency and reliability of electrostatic/triboelectric style monitors. New technological improvements have been developed that are based upon the principal of unifying dc (impaction) and ac (induction) signals and incorporating other proprietary circuit innovations. This higher signal resolution technology results in a more robust and stable measurement for detecting the presence of particulate in a dust collector emission duct or a flow process pipe.

By Ronald M. Fedrick

The microtunneling project for the State of Hawaii's Natural Energy Laboratory (NELH) facility in Kona, Hawaii, was awarded to Nova Group Inc., Napa, California. Nova has developed both microtunnel and deep pile cofferdam experience. Both of which would be required for this project. The project was designed by Makai Ocean Engineering of Honolulu as a continuation of the Ocean Thermal Energy Project (OTEC). The world's first OTEC plant has been successfully operational at NELH since 1982 netting approx 50 kw of usable electric power from a gross generation of 210 kw. A second plant designed to draw 39°F cold water from 3,000 ft below sea level and produce a gross output of 1 mw with a net 500 kw of usable power required 2 - 54 in. finished diameter pipelines. An ongoing problem with earlier offshore pipelines has been the damage to the near-shore pipes within the surf zone. The necessity for a deeper connection between the land based pipe and submerged sea pipeline was obvious. Earlier pipelines had been drilled and shot through the shoreline. This process was only practical at shallow depths. Makai Ocean Engineering and the NELH scientists looked at different methods to get the pipeline through the shoreline at a depth of 80 ft below sea level. Initially, the direction drilling method was proposed as the most potentially practical method. A contract was awarded and various attempts were made to complete a successful

Jan 1, 1995

By H. L. Ehrlich

Modes of microbial attack of metal carbonates, metal silicates, metal oxides and metal sulfides are summarized. The current status of microbial redox mechanisms, whereby metals in metal oxides and sulfides are mobilized, is discussed. Opposing theories of a single mode of attack involving interaction with a microbially produced reductant or oxidant in the bulk phase and of dual modes of attack involving a reaction requiring physical contact between microbe and mineral surface on the one hand and microbial production of a reductant or oxidant in the bulk phase that reacts with the mineral on the other hand are considered. No one mode when finally completely unraveled should be expected to fit all cases. Some biochemical, electronmicroscopic and spectrophotometric approaches for elucidation of missing details of different modes are suggested. Key words: Bioleaching, Biobeneficiation, Metal mobilization

Jan 1, 2003

By R. J. Gary

Why would a company in its right management mind risk a fuel conversion program on a fuel that can't burn if it's too wet or too dry, too hot or too cold, too coarse or too fine, or doesn't have enough Btu's to supplement good combustion? On December 23, 1981, two months ago, we finished our first ten years of burning lignite -- this unconventional coal. It is from that experience that I am qualified to address you today. As some of you here probably already know, my company, Texas Utilities Generating Company, has pioneered the utilization of Texas lignite for electric power generation on a large scale, and I think it is fair to say that we have done this pioneering work largely on our own. Some of us feel like Noah did when he built the arc! I have titled this presentation "The First Lignite Decision" because our company was the first to make this major decision in Texas in the mid-1960's. It was a big decision, and at the time, perhaps a bold one. When you look at the conditions that existed in the mid-1960's, you can see why.

Jan 1, 1982

By H. A. Kortmann

Blast furnace operators have been steadily increasing their quality requirements on burden material. These requirements include a high reduction rate of the ore burden as well as good strength at the beginning and during the whole blast furnace operation. Special requirements are made on the softening and melting behavior which ensures an optimal formation of the cohesive zone in the blast furnace. On the whole, the self-fluxed and olivine-based pellets meet these higher requirements due to their chemical composition, especially in the pure pellet operation. In the mixed sinter/pellet operation partly-fluxed and acid iron ore pellets can be appropriately used. The paper describes the demands on, and characteristics of, different kinds of pellets used in the Federal Republic of Germany.

Jan 1, 1989

By D. A. Norrgran

The recent development of rare earth permanent magnets has revolutionized the field of magnetic separation. The advent of rare earth permanent magnets in the 1980's provided a magnetic energy product an order of magnitude greater than that of conventional ferrite magnets. This has allowed the design of high-intensity magnetic circuits operating energy free and surpassing the strength and effectiveness of electromagnets. New applications and design concepts focused on the mineral and metal processing industries have evolved. This technology also led to the development of various magnetic separators specifically designed for mineral processing applications. Applications which were not previously considered are now being applied to primary mineral upgrading and recycling and secondary recovery.

Jan 1, 1993