Search Documents

By Nikolay M. Sirakov, Michael L. Feves, Rumen P. Mironov, Daniel R. Hack

Subsurface investigation of sand and gravel deposits has generally been limited to test pits and borings. These techniques are problematic in terms of the accuracy, usability, and cost of the final data. Innovations in the application of geophysics have been gaining acceptance in the aggregate industry, especially to determine depth to bedrock and the extent of uneconomic inclusions. This paper presents a system to optimize the processing and evaluation of electrical resistivity data. The system uses 3D separation, geometrical reconstruction, and visualization of subsurface objects.

Jan 1, 2002

By Claus Becker

The Mixshield is a tunnelling machine for water bearing soft soils. Developed on the basis of the Hydroshield, it extents the application of this machine to cohesive soils. The design of the drum-type machine allows three different applications 1. As shield with liquid supported face and hydraulical mucking 2. As Compressed-Air-Shield 3. As Earth pressure balanced shield. The Mixshield is employed on three big contracts 1. a 6.3 km ring tunnel in Hamburg, outer diameter 5.95 m, with a new developed segmented concrete lining 2. a 1.9 km pipe-jack job near Cologne, o.d. 3.6 m 3. Metro Lot 3 in Lille/France, o.d. 7.7 m, 3.2 km long with segmented concrete lining and a most sophisticated separation-plant The site experiences will be reported.

Jan 1, 1987

By James C. Norman

The boron review arrived too late to appear in the June issue. The US was the world's second largest producer and the largest consumer of boron compounds during 1990. Boron mineral concentrate and chemical production in the US totaled 1.13 Mt (1.2 million st), including 565 kt (662,800 st) of boric oxide (B2O3) in 1990, according to US Bureau of Mines estimates. Total value amounted to $404 million. This was slightly higher in production than 1989 but down in value, reflecting a softening in boron product prices. Total world production of boron mineral concentrate and chemical tonnage in 1990 was estimated at 3 Mt (3.3 million st), which corresponds to about 1.3 Mt (1.3 million st) of BO,. World production in 1990 was about the same as in 1989.

Jan 1, 1991

By Verya Nasri, James Sullivan, Alex Varas

"INTRODUCTION Many major cities in the United States have a combined storm water and sanitary sewer network. Regular rainfall overwhelms the system capacity and results in millions of cubic meters of untreated sewage being dumped into local waterways. One legally mandated solution includes several kilometers of large diameter shallow or deep rock or soil tunnels, a pump station as well as associated collection sewers, diversion structures and drop shafts. In this paper, the basis for design of different system elements including the drop shafts and pump station is explained in detail. Common construction methods used for different type of shafts including tangential vortex and baffle plunge, and also pump station alternatives comprising cavern or various shaft configurations are discussed. DIFFERENT TYPES OF PUMP STATIONS The dewatering pump station serves as the heart of any deep CSO tunnel system and is critical to the goal of reducing CSOs by providing a controlled release of the stored tunnel volume to the wastewater treatment plant. As the major mechanical component of the project, the station will require the greatest attention by operations and maintenance staff. Designing a durable and easily operated pump station requires addressing some major challenges, including the following: • Longevity – equipment, materials of construction, and station environment • Controlling odors • Safety for operators and maintenance personnel • Easy access to equipment • Protection from hydraulic surges Location. Owners face a fundamental decision relative to the location of the pump station, which will affect how these challenges are addressed. The pump station can be built within the tunnel launch shaft or within its own dedicated shaft. This decision is driven by cost and schedule. Use of the tunnel launch shaft may provide owners cost saving opportunities by not having to construct a separate pump station shaft. However, this will likely extend the pump station construction as much as two years until the tunneling has been completed. Furthermore, delays to the tunneling operation would delay the pump station construction work, potentially leading to delay claims. For this reason, it has been more common to utilize a separate pump station shaft on recent CSO tunnel projects (Nasri et al. 2015)."

Jan 1, 2016

By D. M. Cregger, J. L. Rosenblad, R. E. Ranken

The construction of a large span, high-walled underground opening in a low strength shale rock is unprecedented. The feasibility of constructing a pumped storage project with several tunnels and a large underground powerhouse in low strength shale rested largely on the feasibility of building stable openings large enough to accommodate the required equipment. Because of the lack of experience with large openings in shale, the decision was made to excavate a test adit and test chamber and conduct a multi-faceted geotechnical evaluation program designed to yield pertinent in-situ data on the ability of the shale to accommodate a large underground opening. Factors considered in the shape, size, orientation, and location of the test chamber were: (1) similarity to the anticipated powerhouse chamber, (2) nature of the most important data to be obtained, (3) feasibility of construction, and (4) economics.

Jan 1, 1983

By N. S. Tanious

Three water-spray ventilation systems were tested to determine their effectiveness in diluting methane at a room and pillar coal mine face. These systems were: the shrouded nozzle, the spray fan, and the conventional nozzle system that is normally supplied with continuous miners. The testing was carried out in two stages. The air-moving capacities of the nozzles were first evaluated in a duct. The duct tests showed that: (1) the volume of air moved by the nozzle is controlled by the type of nozzle, the space around it, and its location relative to the duct wall; (2) the spray fan nozzles or the shrouded nozzles are both capable of moving air quantities up to 6400 cfm (3.02 m3/s); and (3) when the shroud was removed from around the shrouded nozzle, its bare nozzle moved between 9 and 65 percent more air. In the second stage of testing, a full-scale evaluation of the three systems was conducted. The three spray systems were mounted on a continuous miner which was positioned in an aboveground simulated mine entry. The simulated face tests gave the following results: (1) the standard nozzle system, which is mounted on the front end of the miner, is inadequate for diluting methane; (2) under the best testing conditions (lowest methane emission rate, highest primary ventilation airflow, and closest brattice set back), the slight improvement given by either the shrouded system or the spray fan is the same; and (3) under the worst testing conditions (highest methane emission rate, least primary ventilation airflow, and farthest brattice set back), the spray fan gave superior performance.

Jan 1, 1987

By John Waggoner, Steve Klein, John Townsend, Jay Arabshahi

The Riverside Badlands Tunnel is a 13 km (8 mile) long segment of the Inland Feeder Project. This 3.65 m (12 ft) finished diameter water tunnel presented many challenges that had to be overcome to take the project from concept to reality, not the least of which were the diverse ground conditions. Construction of the tunnel was carried out by a single tunnel boring machine (TBM) in one tunnel drive. The project is considered a success due to the accurate baseline established for the ground conditions; the approaches used to mitigate adverse conditions; and the appropriate use of TBM excavation methods, which achieved rapid advance rates despite the challenging ground conditions.

Jan 1, 2003

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

The purpose of this work is to develop a conceptual recovery process for thorium dioxide (ThO2) from its primary source, monazite. The study-level design presented in this paper represents an economically viable method for conducting ThO2 extraction from monazite ore while also recovering byproducts that include P2O5 and other rare earth element oxides rather than producing unnecessary waste streams. Three key points to note in the development of this process design are: (1) the process economics relied heavily on recovery of rare earth byproducts, (2) the thorium handling portions of the process could effectively be segregated from the rare earth and phosphate handling portions of the process, and (3) the thorium and uranium content in waste streams should be carefully managed and eliminated where possible.

By James C. Gilliand

Leo-potpourri, was selected as the title to this paper for several reasons. First, it is a fascinating word--not looking like it sounds or sounding like it looks. It also allows for a great degree of flexibility in designing a presentation around it. Further, it has become popular to use this eco hyphen something pattern. We hear of eco-mania, eco-hysteria and the like. Lastly, in this era of intense environmental concern, two of the principle elements on which the integrity of our efforts must be equated are ecology and economics. Accordingly, the term "Eco-potpourris" allows me to roam at will through the great number of considerations that make up this environmental issue. Whereas only a few years ago the subject of environment and environmental control had low visibility with the public, today it competes as the focus of attention with the many other popular social issues of our time. The program content here at this meeting, for example, is liberally represented by papers dealing with one or more aspects of environmental concern. If one would look at the 1964 program, in contrast, I would expect that no more than possibly one or two papers covered this subject and even then that those papers dealt principally with the environmental aspect of occupational health. It is gratifying that the program at this meeting demonstrates a serious awareness to a broad spectrum of environmental concerns. It would be a mistake, of course, to believe that this clamor for a quality environment is a "flash in the pan" that will soon subside. The general public has been thoroughly aroused and even frightened into

Jan 1, 1972

By Charles N. Alpers, D. Kirk Nordstorm

A variety of approaches have been used in the recent literature for the estimation of pre-mining (or natural background) metal concentrations in areas affected by mining. The following is a list of some of these approaches: (1) historical and anecdotal data, (2) remote analogues (other similarly mineralized areas), (3) proximal analogues (nearby mineralized areas), (4) sediment sampling (streambeds, lakes, estuaries, floodplain deposits, and soil profiles), (5) stable isotopes (hydrogen, oxygen, sulfur, and carbon), (6) geochemical modeling (forward, equilibrium-based), (7) geochemical modeling (forward, kinetic- and transport-based, and inverse), (8) statistical analyses, (9) mass balance on oxygen flux, (10) mass balance with age determination of weathered material. Examples of each approach are described, and the strengths and limitations of each approach are discussed.

Jan 1, 2000

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

7.1 INTRODUCTION Subsidence measurements include surveys of surface and sub- surface movements and measurements and monitoring of surface structural damages. In this chapter the most commonly employed methods are discussed. 7.2 MEASUREMENT OF SURFACE MOVEMENT Surface movements involve two basic components, subsidence and displacement. The other five components (i.e., slope, curvature, strain, twisting, and shearing) are derived from the two basic components. Since all measurements are geometrical, they can be measured by common surveying techniques. 7.2.1 MONUMENTS The first step is to select the types of monuments or surveying stations. Various types of monuments have been employed. The simplest one is a paint mark on the pavement or concrete slab, although this should be discouraged because it is easily affected by artificial or environmental factors. Others use steel or wooden rods, 2 to 3 in. in diameter or square by 2 to 5 ft long, driven all the way down, flush with the ground. Both types of-monuments have no provision for frozen ground heave and both are tampered with easily. A more elaborate type is shown in Fig. 7.1 (O'Rourke et al., 1982). A rebar or iron pipe, 2 in. in diameter by 6 ft long is driven down to nearly flush with ground surface. The top 4-ft section of the hole around the pipe is enlarged to 1 ft in diameter and grouted with concrete. The most sophisticated type of monument is shown in Fig. 7.2 (Conroy and Gyannaty, 1983a). It consists of two hollow steel pipes. The inner I-in. pipe, 10 ft. long is enclosed by a 2-in. pipe at the upper 5-ft. interval. The gap between pipes is filled with foam to isolate the inner pipe from external environmental effects. The bottom of the inner pipe can either remain open or be sealed with a cap, depending on whether the ground is dry or wet. 7.2.2 MONUMENT ARRANGEMENT AND SURVEY LINES The monuments are installed strategically to form survey lines. Three basic types of monument arrangements are shown in Fig. 7.3. Figs. 7.3a and 7.3b are for single and multiple panels respectively; Fig. 7.3~ is mainly for research purposes with multiple survey lines both in longitudinal and transverse directions. This is extremely useful for defining the distributions of ground deformation, as shown in Figs. 2.10 and 2.11. Basically there are two types of survey lines: the whole basin survey line which extends across the panel width or length (e.g., lines R, R, in Fig. 7.3 a&b), and the half basin survey line which covers approximately half of the panel width or length (e.g., lines R, F in Fig. 7.3 &b). Survey lines are generally straight and linear. They should be located on the major crosssections of the subsidence basin. Survey lines must extend beyond the edge of the opening for a sufficient distance so that the edges of the subsidence basin can be determined accurately. The minimum distance from the edge of the opening must be [ ] where h = mining depth, [ ] = angle of draw, and [ ] = 5 to 7 times monument spacing for whole basin surveys, or 8 to 10 times the monument spacing for half basin surveys. There must be at least two controlling monuments at each end of each survey line. Controlling monuments must be located beyond the influence of underground mining. The spacing of the monuments ranges from 15 to 200 ft. The UK National Coal Board (NCB, 1975) recommended a spacing equivalent to 0.20 of the mining depth. Peng and Geng (1982) recommended that the maximum monument spacing be dependent on mining depths as follows:

Jan 1, 1992

By Shawn Benner, David Blowes, Carol Ptacek

A full-scale reactive barrier was installed into an aquifer impacted by acid mine drainage in August 1995 at the Nickel Rim mine site near Sudbury, Ontario. The primary mechanism of water quality improvement is bacterially mediated sulfate reduction and metal sulfide precipitation. Dramatic changes in the groundwater chemistry are observed with up to 90% decline in Fe (from >18 to <2 mmol L-1) and increases in alkalinity from <1 to >10 mmol L-1 (as CaCO3). Over a 3 year period, the rate of Fe removal declines by approximately 35%. Primary controls on barrier performance are organic carbon reactivity, groundwater temperature, and variable residence time within the barrier.

Jan 1, 2000

By K. B. C. Brady, B. E. Scheetz, J. E. Cuddeback, T. W. Bergstresser, W. A. Telliard, S. C. Parsons, R. J. Hornberger

Two weathering procedures are being developed by the Acid Drainage Technology Initiative in cooperation with federal agencies(OSM and EPA). Objects are to: (1) standardize existing humidity cell and leaching column procedures; (2) improve test methods by maintaining a carbon dioxide enriched environment needed to optimize carbonate mineral dissolution, and quantifying particle size variables to evaluate reaction kinetics, and (3) provide flexibility in test method implementation consistent with EPA guidelines for Performance-Based Measurement Systems. Preliminary results indicate the CO2enriched leaching environments produce alkalinities that are similar to field observations and greater than the tests run under atmospheric PCO2. Leaching columns produce higher alkalinity than humidity cells.

Jan 1, 2003

By D. Loy LeRoy

As we are all aware, the impacts of the 1977 Surface Mining Act and the implementing OSM Regulations require application of new, as well as existing, equipment and technologies. Our firm recently completed (June, 1979) a study for the Department of Energy titled "Analysis of the Impact of Public Law 95-87 on Mining Performance." The objective of the study was to analyze the impact of the Act and its regulations on mining performance in order to provide recommendations to alleviate the impacts identified, including identification of research needs. This paper presents some of the highlights of that report: projected cost increases; additional equipment needed for compliance; review of methods currently practiced or those which can be modified; and will focus particulary on equipment and technology applications.

Jan 1, 1980

By Judson H. Whitman

To evaluate intelligently and to market a source of rare earth raw material, it is necessary that the producer understand the requirements of the processor and the manner in which these requirements effect the value and salability of his product. This paper will be an attempt to aid in such an understanding. The majority of rare earth processors are primarily chemical companies, not mining or metallurgical companies, as the complexities of the processing procedures are&apos; much more chemical in nature than metallurgical. The rare earths and the rare earth industry are normally divided into two groups - the ?light? or cerium group and the ?heavy? or yttrium group. They are so named because cerium and yttrium are the most common elements in &apos;heir respective groups and are so divided on the basis of mineralogical and chemical characteristics. The dividing line of the two groups is not rigidly fixed but usually is considered as being between samarium (atomic number 62) and europium (atomic number 63). Although the two groups are quite similar, processing procedures differ significantly, hence most processors tend to specialize in one group or the other. There is, however, a growing tendency toward participation in both groups.

Jan 1, 1960

By Keiichi Fujita, Katsumoto Ueda, Hiroshi Nakauchi, Naohiko Okumura

INTRODUCTION This paper presents (1) modified slipform system which was employed for simultaneous concrete placement for permanent lining and Instruction of a partition wall in the execution of a ventilation shaft 620m deep, and (2) current shaft sinking techniques which have been applicable and efficient for the subsurface conditions in Japan. MODIFIED SLIPFORM SYSTEM FOR PERMANENT LINING OF VERTICAL SHAFT General Information This paragraph deals with rapid construction by using modified slipform system for the permanent concrete lining and a partition wall of ventilation shaft, which has inside diameter of 620m and depth of 620m, of Enasan Highway Tunnel. The general feature of the shaft is illustrated in Fig. 1 and standard section of the shaft is illustrated in Fig. 2. The geological condition surrounding the shaft is mainly of ryolite and surface is of talus, but as a whole, they are rather weak and weathered rocks with faults, fissures and clay seams. 220mm borehole for the geological investigation was used as a drainage hole, predicting the amount of water inflow into the shaft to be 10t/min. The shaft was executed mainly by means of the conventional short step sinking method of 1.2m lift, employing temporary headframe and hoists. For each lift, 40 to 50cm thick temporary concrete lining was used. About 28,600m3 of rocks were excavated and

Jan 1, 1979

By R. Hemp

This paper describes work carried out to obtain a heat balance in the B3 shaft longwall stope at Blyvooruitzicht gold mine. Recordings were made of the temperature of the air and chilled water entering and leaving the section during three periods, August 1 September 1977, November 1 December 1977 and March 1978. These recordings, together with numerous other measurements were used to determine the rate at which heat was being removed from the section by the various fluids flowing through the section. The rate at which heat was entering the section was then calculated, by considering each source in turn. These two sets of figures made it possible to draw up a heat balance, and also obviously gave vital information on the magnitudes of the various heat sources and on the methods used to remove heat. In general reasonable heat balances were obtained, the errors being in the range -6 per cent to +22 per cent.

Jan 1, 1980

By Michael Li

Unsaturated flow and solute transport were studied in three large columns measuring 1.5 m diameter x 2 m height, loaded with up to 3.7 t of oxidised waste rock, which was excavated from the Stratmat pile at Heath Steele Division, Noranda Inc. and contained elevated concentrations of zinc in the pore water. The bottom of each column was partitioned into 37 squares, each of which was drained independently. Following rain simulations at the top of the rock bed, the drainage in each drain port was monitored for volume and physicochemical parameters at pre-determined intervals. This paper describes some of the observations resulting from the experiments. The main conclusion of the study is that unsaturated flows in waste rock are heterogeneous, and flow channelling is ubiquitous. The results imply that the transport of solutes from oxidised waste rock to its toe drainage is subject to various controlling mechanisms, including geochemical equilibrium control and successive pore water dilution control.

Jan 1, 2000

By Maria C. Jaime

Optimization of the rock cutting performance plays a major role in the tunneling operation. For a given set of tool and cutting environment, rock fragments may be chipped away in numerous manners and it is crucial to understand and be able to predict the dynamics at the cutter-rock interface. This paper presents rational and realistic 3D finite element modeling of rock cutting where typical computational issues ?such as contact formulation, appropriate rock material response, mesh distortion, and crack propagation? are overcome. Cutting forces and failure mechanisms in this finite element analysis are successfully validated by laboratory single-cutter scratching tests in sandstone.

Jan 1, 2010

By R. A. Speirer, T. C. Bettinger, L. P. Richardson

INTRODUCTION The Bureau of Mines (The Bureau) remote sensing researchers at the Denver (CO) Research Center, have been investigating computerized methods to detect and map surface linear features called "lineaments" for ground hazard assessment in mines. Many of these lineaments at the test mine site were found to correlate to subsurface geologic discontinuities such as faults, fractures, and joints that intersect coal seams at depth. These features adverse1 y affect the roof and rib integrity in underground mines, thus contributing to rock failures that may result in injuries to mine workers and loss of production. Advance knowledge of the existence of such hazardous geologic features can aid in mine planning and development. Lineaments may be observed in a variety of images of the earth&apos;s surface. Linear features that can be observed using Landsat mu1ti spectral scanner data (MSS) images range from regional (greater than 3 miles in length) to an intermediate length of from 1 to 3 miles. These images are recorded in discrete radiation bands in the green, red, and near-infrared portions of the el ectromaynetic spectrum. These data are acquired from the EROS Data Center of the U.S Geological Survey, Sioux Falls, SD, in digital format on magnetic tapes that are suitable for processing on certain minicomputers. Shorter lineaments length (less than 1 mile) can be observed in high- to low-a1titude aerial photography, radar, and infrared images with image scale ratios of 1:1,000,000 or less. These linear features can correlate to smaller dimensioned faults, and to fracture and joint sets at the local geologic scale. Other informational sources can help substantiate 1ineament analyses, such as well logs, mine naps, topographic data, and geophysical data acquired over the study site. These data must be in a digital format to process on the "DEC PDP 11/23 minicomputer system1". Data can be acquired in

Jan 1, 1986