Search Documents

By John J. Mancini

Elastomeric liner products have been used for over two decades in a wide variety of uses including pond liners, hazardous waste barriers, dam face rehabilitation and mining applications. Asphalt blended with polymers is enjoying renewed interest in the engineering community because of its durability, high yield attributes, fewer CQA steps due to seamless installation, and ease of installation and repair. As in other lining technologies, advancements in polymer chemistry and improvements in installation techniques have had dramatic impact on the quality of fluid-applied asphalt (FAA) membranes. Membrane 6, man­ufactured by Deery Oil, Inc. for over 16 years is a hot-applied polymer modified asphalt membrane that can be applied to a variety of substrates in a reinforced configuration or installed directly on an asphalt surface. By blending thermoplastic polymers with asphalt, very favorable stress/strain characteristics can be achieved (Chambers, 1980). Typically the membrane will yield under rel­atively low stress and also exhibit high elongation capability. In service applications where puncture resistance is a concern, fluid applied asphalt materials have the flexibility and com­pressive strength under heavy loading that leach pad designers may find attractive. Additional security is achieved if long term service life is important as in the case of radioactive waste con­tainment. The Department of Energy selected Membrane 6 over seamed liners for a surface barrier that must isolate and contain radioactive waste for 1000 years. Asphalt has a long history of use as a water-stop material and it is believed that this natural construction material combined with SBS polymers will per-form for a millennium. (Freeman, 1994) The process of installing Membrane 6 varies according to job size and the type of surface to be protected. Lining applica­tions on compacted substrates require the membrane to be applied to a scrim cloth (fig 1). Some early pioneers in FAA technology neglected this step and therefore never achieved per­formance levels that satisfied regulatory guidelines. The scrim provides a cohesive surface that promotes membrane flow while achieving high impermeability (2Xl0 '11).

Jan 1, 1996

By L. F. Moran

Rod Mill Grinding is an important and fundamental step of the concentrating process in Marcona Mining Company's plants at San Nicolas Bay, Peru. This Paper summarizes experience in regard to consumption and specifications of grinding rods based on twelve years operation of the grinding circuits. Marcona operates a Plant complex producing 10 million tons per year of beneficiated iron ore products including pellets, sinter feed concentrates, high grade concentrates as slurry and filter cake. Processing capacity is 15 million tons per crude ore per year of which 13 million are around in rod mills. A continuous testing program was carried out over the years. Initial studies of daily production operations gave indications of poor grinding rates in relation to mill size and power consumption, with a high rate of broken liners and rods. The broken nieces of rod were not automatically expelled and further interfered with grinding efficiency, while replacement of liners caused unwarranted do n tire. Objectives were to improve all phases of the Process by studying the effects of changes in rod diameter, length, alloy constituents, and volume and weight of rod charge.

Jan 1, 1975

By Carl F. Austin

The subject of strata control in mining can be approached from both static or loading concepts or from dynamic or impulsive loading concepts. The fracture process itself appears to be primarily a dynamic process as is the gross creation of fractures through the use of impact, stress wave passage or in more general terms, the use of explosives. This paper presents experimental results which indicate that the understanding of the fracture behavior of rock that has been, established in the open literature is not always appropriate. In particular, the results of this experimental program have shown very interesting differences between the formation of fractures in rock and the formation of fractures in other materials such as metals and plastics which are often used as models for rock behavior studies Fracture patterns and causes of dynamic fracturing in various rock and artificial materials are presented.

Jan 1, 1965

By H. W. Newcomen, D. R. Brox

Assessments of the stability performance of open pit highwalls have traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work have been reviewed and are generally endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on the observed trends in highwall strain data from the case histories presented.

Jan 1, 2004

By Daniel R. Walton

This paper covers several points of interest to mine engineers and planners involved in evaluating or conducting geostatistical coal reserve estimates. In particular, the ability to optimize borehole drilling locations and minimize drilling costs is addressed. Also discussed is the concept of confidence intervals for estimated coal characteristics obtained through geostatistical estimates and their importance in decision-making for mine planners. Finally, a discussion is presented on how geostatistics enables identification of invalid data points and actually forces strict attention to data editing and proper geologic interpretation.

Jan 1, 1982

By C. Allen Born

There is a saying, the greater the gratitude, the shorter the speech. That puts me in a quandary, because while I am grateful for the honor you do me today, I also want to talk about a subject very important to all of us. A few months ago, when I was asked to submit a title for my talk, I chose "Quality where it counts." I did so because perhaps the most important thing we at Amax did in our restructuring was to commit to quality in all our businesses - quality people, assets, and operations. Together, they create quality performance, which produces quality growth and increased shareholder value - our prime corporate mission. We are dedicated to quality. At Amax, quality means everything. Today, I want to discuss quality in another context - the need for it in American education and what we have to do to achieve it. If we ignore this need, we will all suffer the consequences. And they will be upon us far sooner than the next century, barely a decade away. I think almost everyone in this room works for an organization that had to restructure in the 1980s. Mining companies that did not, just didn't make it. Well, we did. As an industry, we are seeing improved profits, positive cash flow, and a more competitive position in the world marketplace. But all the restructuring we have done, all the hard work, and all the pain that was part of it, will be in vain if, down the road, we do not have the educated people we need as workers. We need them to design, manufacture, and market the products that use the basic materials produced by the mining industry. Simply put, we are at a crisis point in education today. That is no new revelation. Nearly six years ago, the National Committee on Excellence in Education published its report, "A Nation At Risk." Since then, things have not gotten better. The Wall Street Journal, Business Week, US News & World Report, and Fortune have all recently published stories about the sorry state of education in the United States. The subject has become the topic of TV talk shows as well as national commissions, and for good reason. The pool of young people entering the US labor force is dwindling. In the next decade, 10 million fewer will enter the job market compared to the 1970s. But fewer of them will be qualified to do the jobs available to them. Here's why: • 20% of today's high school students drop out before they are 18 and another 20% graduate functionally illiterate; 40% of today's fourth graders think the world is flat; • 20% of today's sixth graders cannot locate the United States on a world map; • one of every three ninth graders cannot figure the change for a two-item meal - and I'm talking about a Big Mac and fries. These are not just problems of minority kids in big city ghettos. Fully 40% of all young working Americans cannot add up their lunch bill. Three out of every five college freshmen need some kind of remedial work. These statistics are frightening. Particularly so because, while the work force is becoming less qualified and our public education system is getting worse, our products and technologies are becoming more complex. We are approaching a time when we will have machines that recognize handwriting but people who cannot write. We will have technology to take voice commands, but people who do not know what they are talking about. The accelerating pace of technology is changing the nature of the job market. The fastest growing jobs now, and in the years ahead, are in professional, technical, and sales positions requiring the highest education and skill levels. Most of these jobs will require the use of a computer. Yet, 95% of today's graduating high school students have never laid a finger on a computer keyboard. While our education system is failing the students it is supposed to serve, other countries are doing far better. In a

Jan 1, 1990

By Y. S. Roditis

A new method for interpolating a block model is proposed, where both the diamond drill holes (DHs) and blast holes (BHs) data are used. Combining these data types poses a geostatistical "class size" problem due to the different statistical properties of the densely populated BHs and the sparsely populated DH data. This paper discusses how linear regression was used to adjust the DH values prior to the interpolation to account for the "class size" problem which is inherent to the procedure. The correlation between the BHs and the DHs is found. The DHs are then corrected based on the regression line. Each block that falls within a certain range of influence of a blast hole is assigned a different code and is interpolated with the combined BH and regressed DH data set. Blocks that fall outside the range of blast hole influence are interpolated using the original DH data set. A comparison against other methods, indicate a 12% improvement over using DHs only and a 2% improvement over using BHs only.

Jan 1, 1992

By P. F. Mataich

When the subject of plant computers is brought up most people visualize the computer's controlling the entire plant with very little operator intervention. Actually, this picture is true today in only a limited number of cases and will certainly not be true in the minerals industries for many years to come. There are several ways in which a plant computer can significantly contribute to improving plant operation and closed loop control is only one of these. First of all, what are the basic ingredients for good plant control? For good plant control, two requirements must be met. First, the operator must get good information feedback from the process and then he must know what action to take in response to this information. Control information can be obtained through instruments, laboratory analyses, or through simple visual observation. If it is timely and accurate and the operator knows how to use it, then we have the makings of a good plant control system. The computer can be of help in both these areas by getting good data back to the operator and in helping to develop a good control scheme for the plant.

Jan 1, 1966

By James P. Savely

This paper describes the development of a trim blast design to improve the stability of a final pit wall. Description is given of the effects of rock characteristics, rock type, and pit plans on the blast design. Currently, six benches have been mined with trim blasting. A more stable final wall has resulted and the successful program has reduced mining costs over an extended time period. Low cost blast monitoring and field observation were used to determine peak particle velocity and blast damage. Using criteria developed from this relationship, trim blasts were designed and evaluated.

Jan 1, 1986

By R. Fedel-Moen, R. W. L. Kimber, B. D. Williams, S. R. Ragusa

The use o f cyanide to extract gold from ores is widespread. In the process of extracting gold, cyanide may form metal cyanide complexes with a variety of other metals present in the ore. This study was carried out to investigate the biodegradation of the Cu(I)-cyanide complex and tetracyanonickelate under varying pH and nutrient additions. Detailed studies using shake flask cultures and bioreactors showed that naturally occurring bacteria residing on gold-leach-pad ore uti¬lized the Cu(I)-cyanide complex (CuCN) and tetracyano-nickelate, Na2(NiCN4), as carbon and/or nitrogen sources. Ammonium-nitrogen (NH4+-N) and/or cyanate (CNO-) accumulated in solution as the metal cyanide complexes were degraded. The accumulation of cyanate as a product is a concern due to its toxicity. Degradation rates were increased if a growth substrate (peptone, 0.1%) was added to the medium or if bioreactors were primed with peptone before addition of the metal-cyanide complex. Tetracyanonickelate was degraded at pH 8 without added peptone, but it was not degraded at pH 10. The addition of peptone was required for degradation of the Cu(I)-cyanide complex at pH 8 and pH 10. At pH 8, the addition of peptone resulted in the accumulation of cyanate, whereas, at pH 10, cyanate was not detected in the cultures. Biodegradation of metal-cyanide complexes was faster (approximately 1.5 to ten times faster) in bioreactors than in shake flask cultures. The addition of peptone was not required for degradation of metal-cyanide complexes in bioreactors. However, priming the bioreaetor with peptone resulted in higher metal-cyanide degradation rates over multiple cycles.

Jan 1, 2000

In west-central England, 183 m (600 ft) below the Cheshire Plain, lie the evaporate remains of an ancient sea. Stratified into nine beds of salt separated by marl bands, the deposit stretches roughly 21 x 12 km (13 x 7.5 miles) and contains reserves of rock salt estimated as high as 400 Gt (440 billion st). The Winsford Salt Works, one of England's largest underground mines, extracts the Cheshire salt and sells it for use as animal feed, for application in de-icing programs, and as a key ingredient in sodium fertilizer production and a variety of other industrial processes. Because road de-icing is an important market, demand for Winsford's salt varies with the severity of British winters. Design capacity is 2.25 Mt/a (2.5 million/year). However, production peaked at 2 Mt (2.2 million st) in 1987. Over the past five years, annual production has averaged 1.6 Mt (1.7 million st). Run-of-mine salt averages 92.5% NaCl, mixed with about 5% marl. The marl was formed by deposition of a reddish dust blown into the Cheshire basin from deserts in what is now central Europe. Association with the marl adds color to the salt, producing tea-colored crystals that resemble unrefined sugar. Adaptation of coal mining systems Rock salt mining in the Winsford district began at least as early as 1682. Mining at the current site dates from 1844 but was shut down from 1892 to 1928. In the early 1900s, a series of catastrophic collapses and floods plagued and ultimately shut down then-active Cheshire brine-salt producers. Subsequently, Winsford reopened and began adapting mechanized underground coal mining systems to rock salt extraction.

Jan 1, 1992

By W. C. Dailey

National Steel Pellet Co. operates eight 8.2-m diameter by 5.5-m long (87- x 18-ft) SAG mills to grind 15.24 Mt (15 million It) of taconite ore per year. Improvements to increase mill throughput, lower steel consumption, lower power consumption, and increase grinding efficiency will be discussed.

Jan 1, 1987

By Lynn B. Hales

Flotation performance varies widely as feed conditions change. Maintaining metallurgical targets has proven almost impossible without automatic control. Traditional control methods and procedures are inadequate. Using on-line x-ray analyzers, reagent control and accurate froth level control with flotation models and "Expert" computer control systems has improved metallurgical performance significantly. Examples of actual plant cases are described as well as the expert system methodology.

Jan 1, 1989

By M. Pantazidou

Motivated by recent EU legislation already entered into force or in preparation, this article aims at offering glimpses of the future landscape in the area of subsurface protection against contamination from point sources. Towards this end, it discusses the most salient parts of legislation for the protection of water resources. It then presents results from the wide consultation rounds organized by the European Commission in order to both receive input and help make all opinions heard on the issue of soil protection. Finally, it introduces key provisions of the recent legislation on environmental liability. From the above pieces of legislation, this paper highlights the elements that concern specifically the protection of the subsurface against spills of hazardous wastes from point sources and the requirements for subsurface restoration.

Jan 1, 2005

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium, and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. [Table 1] affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak- type brines, produced mainly for lithium. MARKET ATTRIBUTES Some of the important market traits common to industrial minerals used by the chemical industry are: 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities. 8. Purchases are generally by contract of one year or longer term, with spot buying playing only a minor role. 9. Contract prices are usually fixed in short term commitments, but may vary according to assay, with premiums and penalties for content above or below the norm; however, general practice is for specifications to be fixed in the contract with minimums being set for the desired material and maximums for undesired elements. In longer term contracts, prices are often escalated on labor, fuel, and other vendor processing costs. 10. Suppliers of individual commodities to the chemical industry tend to be limited in number and are generally medium- to large-size producers that supply a few major consumers. 11. The bulk of the mineral volume is for basic chemical uses, sulfur suppliers to sulfuric acid producers and fluorspar for hydrofluoric acid producers being typical examples. These basic chemical products then are used for the production of other products. 12. Shortage of a supply of adequate quality leads consumers to seek substitutes. In the case of fluorspar, much work is being done on recovery of fluorine from phosphate rock. Success in the form of fluorosilicic acid and/or hydrofluoric acid production could, in time, affect the hydrofluoric acid chemical industry. 13. Markets tend to be characterized by cycles of shortage followed by oversupply, with attendant wide price fluctuations. 14. Baniers to trade can have an adverse effect on the necessary movement of industrial minerals used by the chemical industry in international trade. Antidumping laws, quotas, and tariffs can disrupt or dislocate normal markets. 15. Chemical industry consumers may back-integrate for security of supply or for favorable economics, sometimes by joint ownership and often with experienced mining partners.

Jan 1, 1994

By J. Mastoris

The growing environmental awareness and the need for providing social service to the community, urge the primary sector companies (such as mining) to find new solutions, by adjusting their operations with the special, local conditions and meeting everyday problems in practical ways. We hereby present a real case of re-design of an open pit, closed-bench type industrial minerals (clay) excavation, for the purpose of rehabilitation and utilisation as a water reservoir. The potential use of rainfall water was studied on the basis of covering the irrigation needs and improving the living standard of the neighbouring farmers and also as a project or recreational development of the area by shaping a wetland. The experience from the project progress and the reservoir use has been positive to date and the reclamation plan seems to have the acceptance of the local community.

Jan 1, 2002

By Lawrence P. Bonicatto

The steel industry's increased demand for higher grade pellets has caused the pellet producers to investigate methods of upgrading their product. The Hanna Mining Company's Groveland plant is no exception. The Groveland Mine is located in Dickinson County on the Upper Peninsula of Michigan. The low grade iron deposit is a complex mixture of magnetite and hematite with chert, quartz, jasper, and various iron silicates. (1) Beneficiation is by Humphrey spirals and anionic flotation of the iron minerals. (2) A general flowsheet is shown in Figure 1. Flotation of the spiral tailings makes up about 75% of the concentrate. A minor amount of concentrate, less than 3%, is produced in magnetic circuits. The concentrate is pelletized at the rate of 1.6 million tons per year.

Jan 1, 1968

By S. P. Liebenberg

During the past fifteen years significant progress has been made on carbon-in-pulp (CIP) technology for the extraction of gold. While most research on the mechanisms and kinetics of CIP sub-processes has focused on the adsorption step only, auxiliary unit operations such as elution have received less attention. The mathematical models which have been developed for elution at the University of Stellenbosch can be used for design as well as process optimisation by incorporation into an overall CIP simulation program. Except for these models, no other comprehensive models for the complex elution process are available. It is the aim of this paper to review recent modelling work on competitive elution from activated carbon.

Jan 1, 1995

By K. J. Shoop, S. J. Ripke, T. C. Rao, T. C. Eisele

This study investigated the use of a 7.6-cm inside diameter, 344.2-cm-tall horizontally baffled column to reduce the ash content of a low-sulfur bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage and feed quality. The tests were also carried out to compare the columns performance to a conventional column installation in an operating plant. In this paper, the results of this investigation are reviewed and discussed.

Jan 1, 1999

By N. Roqueñí, J. Loredo, F. Pendás

Impacts of mining on surface water and groundwater occur frequently not only in active mines but in abandoned mines, then the establishment of effective legal mechanisms for the regulation and control of mine waters is a necessary step in order to avoid pollution from mine waters and in consequence to contribute for a sustainable development of the mining industry. Currently there is a lack of a specific European legislation about mine waters and this absence of legislation occurs too at national level in many European countries. This absence of an European specific regulatory framework for mine water pollution questions the effectiveness and the applicability of the current legislation and this fact has led the EC to put forward proposals legislation to adequately deal with environmental and social consequences of mining, and among those proposals is a draft for a directive on waste from the extractive industry that includes provisions for mine water pollution.

Jan 1, 2005