Search Documents

By Ralph Musick, Brian Briggs

The U1h Shaft Project is a design/build subcontract to construct one 6.1 meter(m) (20 feet [ft.]) finished diameter shaft to a depth of 321.6 meters (m) (1055 ft.) at the Nevada Test Site (NTS). Atkinson Construction was subcontracted by Bechtel Nevada(BN) to construct the U1h Shaft for the Department of Energy (DOE). The project consists of furnishing and installing the sinking plant, construction of the 321.6 m(1055 ft.) of concrete lined shaft, development of a shaft station at a depth of 297.5 m(976 ft.), and construction of a loading pocket at the station. The outfitting of the shaft and installation of a new hoist may be incorporated into the project at a later date. This paper will describe the design phase, the excavation and lining operation, shaft station construction and the contractual challenges encountered on this project.

Jan 1, 2001

By L. Alan Weakly

The purpose of this paper is to present a viable method of reinforcing rock pillars by utilizing fully grouted reinforcing steel and a cement - fly ash mortar. Although the fully bonded bolt concept is not new, as exemplified by the present widespread use of resin bolts within United States mines and by the use of cement grouted reinforcing used as back pins in the Kiruna Iron Ore Mine in northern Sweden, (1) (2) the method of stabilizing mine pillars with fully bonded reinforcing is new. This method, called the "grout-rebar system", was first incorporated at St. Joe Minerals Corporation’s Fletcher Mine in December of 1972. The system was used on an emergency basis before extensive research on the mechanics of the system could be completed. Since December of 1972, however, approximately 206 pillars have been reinforced at Fletcher and the system is currently being used on a regular basis at two other St. Joe mines and at two competitor mines in the area. Basically, this paper is a case study of the efforts, research and results of utilizing the grout-rebar system, on a selective basis, at the Fletcher Mine. In addition to information about the system, this paper will explain in detail the three rock mechanics instruments developed by St. Joe and used to measure and monitor rock movement to validate the grout- rebar system.

Jan 1, 1977

By Ron L. Schmiermund

The Ferris-Haggarty underground mine was abandoned circa 1910, and portal discharge has since resulted in degradation of a trout fishery in the receiving waters of Haggarty Creek. Although tunnel discharge varies dramatically in volume throughout the year due to infiltration of snowmelt, compositionally it is a nearly constant low-TDS, pH-neutral, low-sulfate, copper-silicate dominated water. Between infiltration events, components of ARD accumulate in unsaturated, oxygenated environments within upper workings and are delivered to the main haulage level by the subsequent annual snowmelt flush. Mixing with non-ARD mine waters results in neutralization, dilution, and precipitation of amorphous copper carbonate and silicate phases. These mechanisms, combined with variations in the water balance, control the composition of the portal discharge. Understanding the chemical and hydrologic control mechanisms was critical to the design of a passive treatment system to decrease effluent copper concentrations.

Jan 1, 2000

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillar mining (panel width) is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to prefailure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25% to 40% higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Prefailure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to design improvements, as mines become deeper.

Jan 1, 2003

By Dwight R. Coles

The solving of complex metallurgical flowsheet calculations by hand is, at best, a tedious job which often proves that engineers, too, make mistakes. The high cost and long lead time associated with manual flowsheet solutions have led several organizations involved in research, development and construction of extractive metallurgical processes to search for computerized systems which will solve flowsheet calculations. Although design flowsheet programs have been developed by the chemical industry, the ability to solve flowsheets involving particulate solids is usually overlooked. A new computer applications system has been developed at Fluor Mining and Metals which has been designed to accommodate the type of design flowsheets required by the minerals industry. By employing the sequential modular computation technique, a library of metallurgical pro- cessing routines may' be accumulated which are used by a universal executive system. This technique enables rapid solution of new process) .flow- sheets with only a minimum of additional programming effort. The implementation of the FLEXMET flowsheet solution system is the subject of this paper. Some of the major features of the system which are examined include interactive input data handling, automated flowsheet calculation order arrangement, flexible accomodation of unit operations models and advanced management of recycle and specification control calculations.

Jan 1, 1982

By Cahit Helvaci, Robert B. Kistler

Borates are defined as ' 'salts or esters of boric acid; a compound containing the radical B203" (Bates and Jackson, 1987). Borates are defined by industry as any compound that contains or supplies boric oxide. A large number of minerals contain boric oxide, but the three that are the most important from a worldwide commercial standpoint are: borax, ulexite, and colemanite. These are produced in a limited number of countries (Fig. 1), dominated by the United States and Turkey, which together furnish about 90% of the world's borate supplies (Lyday, 1991). Production in the United States originates in the Mojave Desert of California; borax and kernite are mined by US Borax from its large deposit at Boron. Borate containing brines are pumped from Searles Lake by North American Chemical Co., and a limited amount of colemanite is mined by Newport Mineral Ventures from Death Valley. Turkish production is controlled by Etibank, the national mining enterprise, which supplies most of the commercially traded ulexite and colemanite from mines in the Bigadic and Emet Districts, plus borax from the huge deposit at Kirka. Borate minerals have been employed in a wide range of uses for many centuries, dating from at least the 8th century when they were used primarily as a flux for assaying and refining gold and silver. Their valuable properties and relative rarity soon stimulated international trade in borates; Marco Polo claimed to have trans- ported Chinese borate minerals from Tibet to Europe, and his home port of Venice was the center for borate imports and use throughout the Middle Ages (Travis and Cocks, 1984). Borates were traded at relatively high prices for highly specialized applications into the late years of the 19th century. At that time they were being used for medicines, food preservatives, ceramic glazes, and in expanded applications as metal fluxes. It was in that era that borax was discovered in Clear Lake, CA, and more significantly, the playa deposits of western Nevada were found and exploited by F.M. "Borax" Smith and others. Research and development by Smith's company began the evolution of borates from a high priced commodity with a few specialized uses to the relatively low priced chemical raw material used in large tonnages on a worldwide scale today. Borates are often defined and sold by their boric oxide or B,03 content, and most statistical data are listed in tons of B203. Of the products sold by the industry, borax pentahydrate or 5 mol and boric acid are the most commonly traded commodities. Boric acid plants are operated by all of the major borate producers. Glass fiber insulation is the major end use in the United States followed by textile glass fiber and borosilicate glass, detergents, and ceramics. Detergent usage continues to be a major end use in Europe.

Jan 1, 1994

By Jean E. Kiel, Rob Dorey, Dirk J. A. van Zyl

1.1 INTRODUCTION This chapter seeks to provide an overview of important factors involved in the implementation of heap leach technology as a vehicle for gold extraction from its ores. Toward this end, brief discussions of the various elements important to this process are presented here. Topics covered in this chapter include a brief history of the process; basic chemical reactions responsible for the process ; characteristics of ores amenable to heap leaching; location of the greatest concentration of heap leach projects in the U.S.; heap leach components, methods, regulatory/permitting considerations; and economic considerations. Most of these subjects are treated at much greater length in subsequent chapters. Thus, this chapter serves as a summary for those which follow, in addition to providing the reader with a feeling for those topics which may be of most immediate interest. 1.1.1 History of the Process Modern Day Precious metal heap leaching technology has developed over the past decade, although the principles of heap leaching per se, as well as those of gold extraction through cyanidation have a long history (see discussion below). However, it is in the past 10 years that heap leaching has developed into an efficient method of treating oxidized gold and silver ores. It has proven to be both an efficient way to extract precious metals from small, shallow deposits, as well as an attractive way to treat large, low- grade, disseminated deposits. Heap leaching has several advantages compared to conventional milling (i .e., crushing, grinding, and agitation leaching). In general, these advantages include simplicity, lower capital and operating costs, shorter start-up times, and less intensive environmental regulatory concerns. A possible disadvantage of currently existing heap leach technology is a potentially lower percentage of metal extraction being obtained from the ore than would be the case with conventional milling (Potter, 1981; Hiskey, 1985; and Thorstad, 1987) The actual principle of heap leaching has a long history as inferred previously. For example, mines in Hungary recycled copper-bearing solutions through waste heaps in the mid-sixteenth century (Hiskey, 1985), and Spanish miners percolated acid solutions through large heaps of oxide copper ore on the banks of the Rio Tinto around 1752. By 1900, leaching operations were employing such techniques as leach/rest cycles to maximize copper recovery (Taylor and Whelan, 1942; Thorstad, 1987). Copper dump leaching is currently

Jan 1, 1988

By M. Menegaki

Restoration of abandoned mine sites is still one of the weak points of mining practice. The latter stands especially for the case of the surface coal and lignite exploitations, where the extended size of the disturbed land and the drastic changes to the geomorphologic features do not facilitate the implementation of a cost effective and environmentally sound reclamation plan. The paper examines the parameters involved towards the legal requirements for the reclamation of the first lignite exploitation in Greece, namely the ?Plakes? mine, located at Euboea, due to the particularities of the site. Then an integrated redesign procedure is presented, aiming at minimizing aesthetic degradation, confronting technical difficulties and preparing the site to accept new uses.

Jan 1, 2005

'IM existing predictive methods were chosen for evaluation; an influence function (Bals Theory) and a profile function (hyperbolic). These ere applied to several field measured subsidence profiles over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1982

By S. Siewierski, L. Wojno

INTRODUCTION Bumps are among the most dangerous hazards in the Polish copper ore mines. Their occurrence is the result of the dynamic processes in the rock mass caused by natural factors connected with the deposition of strata and, to some extent, by technological factors resulting from the process of exploitation. In this connection, in order to ensure worker safety and choose such a technology that allows an achievement of high technological and economical parameters, a detailed knowledge of the phenomena occurring in the rock mass is required. In copper mines the basis for forecasting and control of bumps is obtained by continuous measurements and observations of the symptoms of rock mass pressure, the analysis of which ensures the accuracy of forecasting and points toward preventive means that must be applied to prevent bumps. The methods most often used for preventing bumps in copper mining are discussed in this paper.

Jan 1, 1982

By R. C. Babcock

Exploration for mineral deposits in the western United States is increasing annually, and the data generated by this effort are increasingly complex, diverse, and abundant. It is obvious that to make full use of this data base, which is both private and public, the technology of the computer must be involved. To lay out the framework for discussion of the particular uses of computers in all steps of exploration, this chapter will discuss the various approaches to the reconnaissance program which might be considered, the types of data to be acquired, the interpretation of these data, and the generation of recommendations based on this interpretation. Where possible, some of those areas where computer technology is now used will be pointed out. The discussion will cover the extent to which the computer is now utilized in those areas or where it should be brought into the program to aid in these activities. However, this chapter will not present an exhaustive evaluation of this technology, but will stress the exploration job and its requirements, so that subsequent discussion of the technology itself can be placed in perspective.

Jan 1, 1979

The American Mining Congress International Coal Show, this year’s largest gathering of coal industry leaders, convened May 5-8 in Chicago. Against a 73 000-m2 backdrop of the coal industry’s most productive equipment,* some 23 000 people heard government and industry executives give guardedly optimistic reports of coal’s near future gains. Although a rocky road lies ahead, operators and suppliers still continue their search to improve efficiency. Among the ideas discussed at the show were better underground communications systems, continuous on-line coal analysis, and recovery of hard-to-float coal.

Jan 7, 1980

By C. Ostrowski, Z. Fajklewicz, K. Jakiel

Results of the application of the micro-gravity method in predicting rock bursts and rock mass deformations are discussed. Research was done in the Daisy black coal mine, Upper Silesia, Poland, during 1979-1980. At that time, microgravity investigations helped increase the safety of coalbed exploitation in progress. During the first stage of exploitation, a mining shock of 107 J energy was predicted in a region where 40 miners worked.

Jan 1, 1987

By J. S. Hall

The productivity and fuel efficiency of iron-ore blast furnace operations has greatly increased in recent times. These improvements, particularly to the Japanese steel industry, have primarily arisen from process engineering studies of the blast furnace and associated operations such as sintering. The development of fluxed sinter based on iron-ore fines reacted to produce highly reducible, low slag sinters has contributed further to a reduction in fuel requirements. The Pilbara province of Western Australia is a significant source of these iron-ore fines supplied to the international market. Increasingly, this market is being offered high quality ores from other foreign sources. To technically assist companies in improving the processing efficiency of ores, and to improve the technical marketing of ores by modelling the processing characteristics of Australian/international ore blends, the Commonwealth Scientific and Industrial Research Organization (CSIRO) is actively assisting the industry by researching the general theme of 'iron ore from mine to metal in this paper we outline progress towards a numerical description of: a. ore deposit classification. b. Degradation during transport. c. Direct reduction of iron ore. d. Liquid bath ore reduction/smelting. e. Industrial sintering.

Jan 1, 1986

By William G. Fischer

Equations developed by an early researcher in subsidence, F. Martos of Budapest, Hungary, have been slightly modified to produce effective equations for predicting the time-dependent nature of Green River trona mine subsidence. Following the initial study, a survey was run to check the results twenty years after mining of the area had been completed. The final results were within a few centimeters of the value that had been projected. Mining conditions in the Green River area are ideal for this sort of study with trough type subsidence being the surface manifestation of high extraction underground room and pillar caving operations.

Jan 1, 1986

By J. B. Pateiro Fernandez, S. Möllerherm, E. Drüppel

"Since 1997 the Institute of Mining Engineering 1 at the Aachen University is dealing with the concept of sustainable development in the mineral industries. During this time it has conducted several research projects in this field. Its latest project is on the development of sustainability indicators for the German mineral industry. This paper describes some results of this project. A process chain analyses have been carried out identifying economic, social and environmental effects of the minerals extraction. Thirty indicators reflecting the particular conditions in the mineral industry have been designed. One important challenge was the design of quantifiable indicators taking into account the life cycle of a mining operation as well as mineral beneficiation and enrichment of the raw material."

Jan 1, 2005

By R. J. Hamilton

Considerable success has been achieved in recent years in reducing concentrations of respirable dust in UK coalmines; thankfully this has been reflected in significant improvements in pneumoconiosis statistics. However, continuous increases in mechanisation and in rates of working, accompanied by more stringent dust regulations, necessitate the introduction of improved and often more sophisticated methods of dust control. The increased application of exhaust ventilation and air cleaning techniques seems likely to be the most important step forward in dust control in coalmining during the next few years. A typical drivage in a UK mine is not more than 16 ft (5 m) wide and is supported by steel arches. In the past the majority of such roadways were driven by the conventional means of blasting and loading. Since the main purpose of ventilation was to clear blasting fumes and to provide adequate scouring of firedamp, not surprisingly it was usual to have 'forcing' ventilation. Present systems of operation are making increasing use of heading machines and it is not surprising that well over half of all drivages are now ventilated by exhausting methods. (1) The great majority of coal getting in the UK is from longwall faces, usually in seams of less than 6 ft (1.8 m) thickness. Although this method of min¬ing has many advantages in terms of safety and productivity, dust control is made more difficult because of the need for men and machines to work in the same ventilation stream. Much emphasis has been placed on improving the design and methods of opera¬tion of longwall machines to reduce dust production, and improved ventilation has provided greater dilution, and in consequence, reductions in dust concentration. On all machines water is now fed through internal galleries to the cutting elements. Unfortunately, one of the difficulties associated with mining thin seams is that there is some unavoidable cutting in the roof or floor and in many seams there are faults to be traversed and dirt bands which must be removed with the coal. Under these conditions it appears that the use of exhaust ventilation and air cleaning offers the most promising way of achieving satisfactory dust conditions.

Jan 1, 1980

By E. G. Kelly, D. E. Walsh

The behavior of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effects of particle size, particle shape, pulp density, feed rate and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that, with suitable precautions, the technique is capable of providing valuable information, unobtainable from conventional studies, that could be used to better optimize spiral performance.

Jan 1, 1993

By J. Yordan, J. Zinterer

Effective removal of ink particles by froth flotation is of up-most importance in paper recycling. In this study, the potential use of talc particles as carriers of difficult-to-float fine ink particles is investigated. In order to accomplish ink particles removal, the interactions between talc and oily- ink particles in aqueous solutions containing flotation chemicals was studied by zeta potential distribution measurements and with the impinging jet apparatus. The chemical conditions under which talc-ink adhesion occurs are identified and reported.

Jan 1, 2003

By Y. Lin

The objectives of this investigation were to study the zeta potential characteristics of a Powder River Basin coal in water and to study the effects of zeta potential on the agglomeration of coal particles. The electrokinetic measurements show that the zeta potential of the coal is dependent on pH, temperature, coal concentration and contact time with water. The effects of various additives for changing the zeta potential of the coal were also evaluated. It was found that the strength of the coal agglomerates is increased when the zeta potential diminishes. Neutralizing the zeta potential enhances agglomeration. Therefore, it is important to control the zeta potential of coal to achieve optimum performance in coal-particle agglomeration.

Jan 1, 1997