Search Documents

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By B. V. Driga

The paper presents the evaluation method of the thermal power potential of the salt lakes developed in collapsed salt mines in Romania. It is well-known that the hydro-chemical stratification of these lakes favors warmer internal layers. The degree of heat varies during the year, but, taking into account the large number of genetic lakes of this type, it can be used as a local utilizable power source. The authors analyze the correlations between the physico-chemical parameters of the water and the degree of heat stored as a function of the morphological parameters of the lakes, as well as the technical parameters for capitalizing on this power.

Jan 1, 2008

By C. E. Capes

Reduction in the quality of resources and attendant increase in the quantities of fines to be processed present a major economic and environmental challenge for resource - based industries. It is becoming evident that agglomeration by immiscible liquid wetting will play a significant role in the treatment of these fines. Liquid phase agglomeration can be adapted to separate solids or liquids in highly divided form from liquid suspensions and emulsions. Diverse opportunities in coal fines recovery, novel fuels technologies and oily waste water treatment are cited here. The oil agglomeration of extreme fines from coal tailings, with consequent dramatic reduction in refuse for disposal, is now a commercial reality. It is suggested that this approach can serve as a prototype for the processing of extreme fines in an economical and environment ally sound manner.

Jan 1, 1989

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993

By L. W. Saperstein, R. J. Sweigard, D. L. Simpson

Deep tillage is widely used as a means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids produced during deep tillage in order to prevent any significant recompaction from occurring. Various amendments were injected into the soil during laboratory tests using a small-scale ripping and injection system. Measurements were made of selected soil proper Pies to evaluate the feasibility of this method.

Jan 1, 1994

By Robert J. Ramsey, N. Finkelstein, Foster J. Witthauer

First mining operations in the Tyrone District, located just north of the Burro Mountains in Grant County, New Mexico, commenced in the 1870's. A major operation was undertaken by Phelps Dodge Corporation in the early 1900's when a 2,000 ton per day underground mine was developed and a gravity concentrator was built east of the mine and across the Continental Divide. It was during this time that the picturesque Tyrone townsite was built and occupied. In 1921, however, the underground operation was closed because of high operating costs and low demand for copper. The area was drilled extensively during the 1950's and in October 1966 Phelps Dodge announced the pending development of the new Tyrone with a large open-pit mine, a modern concentrator, suitable support facilities, and a new townsite to be located between the mine and Silver City. Stripping for the pit and construction of shop and milling facilities began in 1967. By the spring of 1969, ore was being stockpiled near the primary crusher. Operation of the concentrator on a 3-shift per day basis commenced on July 17, 1969. The concentrator as initially built had one primary, two secondary, and five tertiary cone crushers, two grinding sections of six ball mills each, two flotation sections, four filters, and four tailing thickeners. 'he capacity was about 30,000 tons per day. In 1971 and 1972, the capacity was increased to 48,000 tons per day by the addition of one secondary and two tertiary crushers, one section of eight ball mills, one flotation section, two filters, and four more tailing thickeners. Centralized automatic control was built into the original and expanded facilities to the greatest extent possible, considering the state of the art at that time. Installation of additional control

Jan 1, 1976

By D. Armour, E. R. Bauer, D. R. Zuchelli, T. M. Durr, E. R. Reeves

A team of noise specialists from the National Institute for Occupational Safety and Health (NIOSH), Mine Safety and Health Administration (MSHA), and Joy Manufacturing attempted to evaluate an engineering noise control on a Joy longwall stageloader. The team developed and executed a test plan to evaluate the noise attenuation of the engineering control in an underground coal-mining environment. An evaluation of the long-term noise effects and durability of the engineering control were also a focus of the research effort. Pre- and postcontrol measurements consisting of a combination of worker dosimetry and task observations, tape recordings, and sound level measurements were used to evaluate the engineering control. A description of the engineering noise control, pre- and post-control sound level measurements, and an evaluation of control success is presented. In the end, no evaluation was possible due to mining practices, miner task variations, and inconclusive data.

Jan 1, 2005

By A. T. Sapulek, C. S. Özveren, D. W. Dixon

The prediction of underground methane emission from longwall coal faces has been extensively researched for a number of years and numerous prediction methods have been devised. Many coal mines employ sophisticated environmental monitoring equipment which generates large amounts of data including, methane concentration, air velocity and barometric pressure. Presently this information is mainly used only to indicate alarm and danger levels of the monitored data for management purposes, however, the potential uses of this data are enormous[1]. This information could be used to good effect within a production/methane emission strategy as detailed in a previous paper[2]. The paper presents a practical application of artificial neural networks to underground methane prediction. Data on methane concentration and coal production has been obtained from an underground coal mine. The data is used in a neural network architecture and forecasts of methane concentration have been obtained. The forecasts are examined and there is a discussion of the potential use of the predictions from neural networks in the field of mining production control.

Jan 1, 1995

By Z. T. Bieniawski, D. A. Newman

The Geomechanics Classijication (RMR System) (Bieniawski, 1979) was modified for entry and roof support design in underground coal mines. Adjustment multipliers were introduced to incorporate the influence of high horizontal stresses and the roof support reinforcement into the existing classification system. Sixty- two case histories of standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant im- pact on the stand-up time of supported coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1987

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, J. Brent Hiskey, Gürses Öner

Currently there is considerable interest in applying in situ leaching technology to recover copper from oxide ores. In many instances, the distribution of copper mineralization in these deposits is fracture controlled. Laboratory core-leaching experiments have demonstrated that leaching response is sensitive to the dissolution of copper from and the formation of channels along main fractures. Solution short- circuiting can be a major limitation of this technology. This paper describes the application of macromolecular polymers to achieve flow-profile control during leaching. Pre- and post-leached fractures were characterized by computerized tomography (CT) analysis.

Jan 1, 1993

By Kenneth J. Miller

Froth flotation is one of the most actively pursued research and development areas in the coal preparation industry today. Many new types of flotation machines and processes are being developed and compared in an effort to handle the increased quantity of coal fines produced by finer grinding for greater liberation of ash- forming and sulfur-bearing mineral matter. Of the many new machines and processes under development for deep cleaning ultrafine coals, it is quite likely that many will not reach industrial use in the near future; in fact, it is quite likely that some never will. Therefore, it is the objective of this paper to select and describe a few of the new flotation machines and processes that appear to have reached a level of development that would suggest their eventual use on an industrial scale. It is probable, and doubtless will be argued, that some of the selections given in this paper should not have been included, while others should have, but the reader must understand that the author is restricted by the information available. And because most of the information available comes from those who are developing the equipment and/ or processes, it is often confusing and conflicting. Thus with a somewhat moderated plan, the author proposes to point out some in- congruities in the literature in the hope that such information might promote more independent study and perhaps explain the abundant promise versus the scant use of the new equipment and processes described.

Jan 1, 1988

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By Ross D. Lawrence

Suggestions have been made that the appraisal of mining assets using discounted cash flow techniques should be based solely on proven and probable reserves in reliance upon the widespread international recognition of uniform resource definitions. Following a review of generally accepted valuation principles, a survey of the literature and, most importantly, a review of real transactions in the open market, it is clear that valuators should not be constrained by the growing acceptance of modern mineral resource codes. On the contrary, valuation practitioners should be encouraged to examine all classes of mineralization and, after making due allowance for risk, to utilize all mineral resources as a basis for determining fair market value.

Jan 1, 2002

By Uday Kumar

This paper presents details of an availability study for a fleet of diesel engine operated load-haul-dump (LHD) machines used in a Swedish mine. For the purpose of this study, the LHD machines have been considered as a system comprised of many subsystems like engine, brake, transmission, etc., in series. As availability is dependent on both the reliability and maintainability characteristics of the system, together with reliability, the concepts of maintainability are also discussed. The need for exploring the data for the presence of any structure, which is very common in repairable system data sets, is emphasized with suitable examples. Simple graphical techniques are used for verifying the independent and identically distributed (IID) assumption for the data set. The error introduced due to the use of the exponential distribution in place of more appropriate distributions in estimation of availability and reliability characteristics is analysed.

Jan 1, 1989

By R. Lindsay Mundell

During the past 12 years, use of longwall methods to mine coal in the United States has continually in- creased. Although these methods offer several advantages, health hazards often exist because of unique and difficult problems in the control of respirable dust. This paper discusses the results of respirable dust studies conducted on United States longwall mining operations in 1972and 1978. Current engineering control methods (ventilation, water application and use of machine cutting parameters) and administrative controls for minimizing employees' respirable dust exposures are discussed.

Jan 1, 1980

By R. Addison, P. V. Avotins, D. W. Kestner, M. F. Dibble, L. A. Haas, M. D. Flavel, D. Halbe, D. J. Barratt, G. V. Jergenaen

Mineral processing in 1980 can be described by several key words, familiar to the industry throughout the past decade: complex, low grade, environmental, energy, high tonnage, and economics. Flowsheets have become more complex in order to treat lower-grade, finer-grained, more complex ores and still meet environmental and economic constraints. Operators and researchers have had to cope with these problems, which have resulted in marked trends in mineral processing. The use of advanced instrumentation in process monitoring, control, and modeling has been increasing to deal with fluctuating ore grades, higher plant capacities, rapidly rising operating costs, and process complexities. The industry has been presented with new generations of equipment that reportedly do the job more efficiently and at a reduced cost. The need to meet stricter air and water environmental standards has resulted in a concerted effort by the mineral industries to obtain an appropriate balance between the needs of mining and mineral processing and the requirements for proper environmental, safety, and health protection. Energy and economic considerations have led to increased equipment size, particularly in grinding, flotation, and conveying. Throughout all phases of mineral processing there has been an effort to reduce energy consumption. One avenue followed by researchers and operators was the testing and use of chemicals to reduce energy requirements.

Jan 5, 1981

By J. Maiti, A. Bhattacherjee

A literature review on quantitative analysis of mine safely studies revealed that numerous investigators explored a wide- range of techniques, including the investigation of bivariate and multivariate statistical models. Although these researchers addressed various issues of accident causation and prevention, they, in general, did not investigate through the use of quantitative models the multivariate relationships of several factors affecting mine safety in a causal framework. In this paper, systems dynamics and structural equation modeling are presented to simultaneously represent and study the effect of policy variables related to accident prevention along with the factors causing accidents and injuries. The application of these models to a group of mines revealed that current training practices at these mines do not appear to alleviate accident occurrences. It is inferred that the use of these quantitative techniques can provide a new direction of research in mine-safety studies.

Jan 1, 2000

By Thomas P. Meloy

As the importance of particle shape in mineral processing is increasingly recognized as an major variable in predicting the behavior of both individual particles and particle systems, whether it be in dense media, froth flotation, comminution or the flow of particles, new method of shape characterization are being developed, particularly for use on image analyzers. These shape characterization methods may be broadly classified into the analytical, empirical and physical formation methods. Discussed are approaches and the strengths and weakness of each of these methods. Moreover old and new shape measuring techniques are reviewed, particularly the new image analysis methods techniques such as Fourier, Haar, Fractal, Walsh and Delta as well as a variety of other techniques such as tabling, the Cascadograph, settling and L/D ratios. Also discussed are the problems of doing shape research, current progress and the future of the field.

Jan 1, 1990

By F. Vincent, A. Boulet, M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. It makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery data to gravity recoverable gold (GRG) to predict overall recovery. The methodology is designed for gravity circuits located in the circulating load of secondary grinding mills. Gold liberation is estimated by processing a sample of representative ore with a laboratory Knelson Concentrator (LKC) in three successive steps, each at a finer grind than the previous one. Breakage behaviour is represented by a matrix H, which redistributes GRG in the feed of the secondary mill in the various size classes of its discharge. Provision is also made to account for gold overgrinding, which decreases the overall amount of GRG. Classification, pre-concentration and recovery data are estimated from plant performance, and are represented by the diagonal matrices C, P and R. The methodology is demonstrated with case studies of greenfield, retrofit and optimization applications.

Jan 1, 1995

By B. K. Mishra, R. K. Rajamani

Discrete element is a numerical technique for describing the collision dynamics and motion of an assembly of particles. In particular, calculations are done on full three-dimensional space with a force-contact law for collisions and Newton’s law for subsequent motion. It may be said that there is no empiricism in this approach. The paper describes the full scale simulation of large diameter semiautogenous grinding mill of size 40X24 ft. It is shown that the simulation predicts the power draft of plant size mill extremely accurately. Also these simulations have been adapted uniquely to assess the motion of pebbles and slurry in pulp lifters. The passage of slurry from pulp lifters into trunnion is extremely important since flow-back and carryover must be avoided at all cost. The dynamics of slurry flow through pulp lifters is also described in this paper.

Jan 1, 2003