Search Documents

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"In recent years, much has been said and written on Lake Superior ores, giving the impression that the quality of the ore is deteriorating in grade and that the reserve of high grade ore is rapidly being depleted. Average analyses of ore produced in this district since 1902 show that the average quality has been practically uniform since 1910, and now closely approximates the average for the total reserves of merchantable ore.The accompanying tables and charts show the average analyses for the past ten years, weighted according to tonnage: The chart above shows graphically the average natural iron content for the old range, Mesabi, and grand total Lake Superior ore shipments since 1902.During the last ten years the decrease in iron content for shipments from all ranges except the Menominee was only' .05 of 1 per cent, while for the Menominee ores there was an increase of .052 of 1 per cent. These tabulations and the chart prove that the average quality of the total annual production of iron ore from the Lake Superior district is uniform. Mining men of the district know that all of the merchantable ores of every ore body are being mined out cleanly, and therefore the present average iron ore content of total annual shipments from the district may be expected to continue as long as the present merchantable ore reserves last. There is no logical reason to expect a decrease in the average iron content. Furnaces require ore of definite quality, and if this quality of ore cannot be produced from the natural ore bodies, it must be produced by mechanical means—that is, by concentration of low grade ores or iron formation."

Jan 1, 1920

By Karl Gunnar Holter, Frank Clement

"INTRODUCTION Typically waterproofing of conventionally excavated tunnels has been done by installing pre-fabricated sheet membranes between the primary temporary support lining and the secondary permanent inner lining. The membrane acts as a separation or sliding layer between the linings, which is often desirable. The geotextile installed behind the sheet membrane provides the required drainage and protection of the system. The design of the tunnel lining is strongly influenced and limited by the use of waterproofing sheet membranes. Since primary and secondary linings are separated from each other, forming a double-shell lining system. In that case the secondary lining must be designed for all permanent loads, although the sprayed concrete primary lining continues resists ground and water loads for a long time after construction. Significant progress has been made in sprayed concrete technology over the last two decades, with advanced admixtures, as well as the improved application technology using spraying robots. The development of new admixtures like superplasticizers based on poly-carboxylates, alkali free accelerators and silica fume, enables designers to use permanent sprayed concrete linings (SCL) increasingly for long-term service life. When designed and applied correctly, sprayed concrete can be considered as permanent. The use of spray applied membranes has seen increased use over the last decade in some countries, and demonstrated functionality and cost-effectiveness in several situations. This paper describes the use of the sprayed waterproofing membrane MasterSeal 345, an EVA polymer based product, and the practical experiences from several projects. SPRAY APPLIED WATERPROOFING MEMBRANES The sprayed waterproofing membrane is polymer based and has been especially developed for underground structures. The membrane is applied between primary and secondary concrete linings and develops high bond strength on both sides to the concrete (doubled-bonded)."

Jan 1, 2016

By K. K. Bhattacharyya

In the Gulf Coast area lignite deposits occur in Texas, Louisiana, Arkansas, Mississippi and Alabama. Lignite has been mined in Texas since the early 1800's reaching a production of over 900,000 metric tons (1 million short tons) in 1910. With the availability of inexpensive oil and gas, production fall to as low as 16,000 metric tons (18,000 short tons) by 1950 (Henry, 1976). With the advent of the oil and gas shortage in early 1970, lignite production began to increase again. The purpose of this paper is to discuss the geotechnical considerations of mining lignite in the Gulf Coast area, particularly Texas and Louisiana. Lignite deposition occurs in unconsolidated sand, silt and clay environments. Extensive sand units saturated with water may be present within the potential mining depths. This paper describes the geotechnical considerations for designing a surface mine in this geographical area. These factors include geology, hydrology, mining method, and equipment utilization.

Jan 1, 1982

By M. Gershon

Four computerized approaches for coal blending are described and their strengths and weaknesses are explored. Spreadsheet analysis Other than word processing, spreadsheet software is the most commonly used software. Its wide availability and ease of use are two desirable features that have led many to try to adapt it to the purpose of coal blending. These are the two main advantages of this approach. To use a spreadsheet for coal blending, each row of data represents one source of coal. Each column represents a quality of the coal, with the last column specifying the tonnage of that coal in the blend. The calculated figures are. the blended qualities, which can be programmed to appear in the bottom row. A trial-and-error approach is then used to develop the best blend. Inserting any blend in the last column provides the blend characteristics at the bottom of the page. If any specifications are not met, the blend can be changed, all calculations being immediately updated. This process is repeated until all specifications are satisfied. A third advantage of this method is that it is exactly the procedure that one would go through if doing this by hand. With a spreadsheet, many more blends can be evaluated in much less time, allowing the designer to try to improve over satisfactory blends to find the best of them. The resulting improved blends or cost savings are a fourth advantage of this approach. There is only one major disadvantage of using the spread- sheet. This is that most probably the best blend is not found. As an inexpensive introduction to computer-assisted blending, which can be easily understood and cost just a few hundred dollars, this is a recommended place to begin.

Jan 1, 1987

By Ben Ainsworth

I am going to discuss gold mining in Mexico during the last twenty centuries and try to suggest some of the futures that may develop in this industry in the next decade. Before I start this rapid review of such a long developing mining tradition, T must give credit to my sources. I an, talking here as an associate of Commoditi,c,s Reseflrch Unit Ltd. of London (better known as CRU) and as a principal of Ainsworth-Jenkins Holdings, an international mineral resource consultant group that has been exploring and deveJoping mining properties in Mexico and Central America for the last six years. CRU is the leading consultancy providing industry, governments and financial institu­tions with analysis and advice on the metals and the mining industries. They recently completed a three volume study entitled Gold Mining Opportunities in Mexico. This .<1tudy describes Mexico, the business environment, its geology and details its gold mining potential with property descriptions and maps. I have adopted and adapted the s11mmari.zed Mexican government statistics and rlrawn on some of the historical comments in these volumes. However, I do not have ti me (nor would it be appropriate) to be giving the details of the CRU work. Jorge Ordonez, whose shoes I am trying to fill today, was a major contributor to the study and it was an honour to be asked by Willem Beunderman, the Principal Editor, to step in when Jorge was unfortunately unable to be here. Jorge has been an enormous help to Ainsworth­Jenkins and a consistent friend of foreign investment in Mexico. Our own work in Mexico has allowed us to obtain a few useful in­sights into this most interesting slice 0f Mexican history.

Jan 1, 1992

By W. T. Walter

High-G centrifuges from five preparation plants were sampled to determine and quantify the various operating factors affecting performance. The operating factors that were considered include feed rate and percent solids, size of feed material, screen-basket type, hardness of coal and age of the flights. The performance parameters that were measured include product surface moisture, recovery and degradation of the coal. Regression equations with good significance levels were developed.

Jan 1, 1982

By Barrie C. Butt

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been in progress for six years and the writer has been intimately associated with the project during the five years of exploration and the six years of exploitation. The industry is possibly aware of the fact that the Woodsreef Mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and of the fibre. Because of these unique features, a large volume of research has been undertaken by Woodsreef and by other scientific organisations in Australia, England and Canada on the Woodsreef fibre. The answers to some of the problems have negated some semi-sacred concepts of asbestos ore milling and led to the development of new techniques, such as the adoption of microscopic fibre counts as a routine procedure; the modification of accepted evaluation procedures; the development of new machines for dedusting fibres, and to the recognition of a fibre with a unique milling behaviour pattern and, possibly, properties. The problems experienced can be divided broadly into those associated with the geology and those associated with the physical properties of the fibre. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognised during the exploration stages a feasibility evaluation may be just that little closer to the actual.

Jan 1, 1978

By Brian Stimpson

A recent study by the National Academy of Engineering concluded that if the U.S. Coal Industry is to double production by 1985 it must open 30 new 2,000,000 tons per year surface mines in the eastern states and 100 new 5,000,000 tons per year surface mines in the western states, in addition to major growth in underground mining. Major expansions in coal mining are also planned in other countries. Engineering geology can play an important part in coal mine development, operation and abandonment (Table I), and with the increasing scale of surface coal mining and the requirements of environmental legislation, it seems certain that engineering geology and geotechnics will play a growing role in surface coal mining.

Jan 1, 1976

By Hou Xilun

Three production methods of rapid cold bonding and low temperature bonding pellets using sponge iron powder as a binder have been successfully developed. These methods differ from ordinary bonding method by no addition of salt and other catalyzers, no corrosion of equipment and no pollution of environment. Mechanism of pellet bonding is studied. Experiment shows that these pellets have good metallurgical properties. A semi-industrial test has proven the laboratory results, with the production of metallic pellets continuous and stable. These methods are substituted for traditional high temperature firing of oxidized pellets in direct reduction. As a result, the plant for oxidized pellets can be saved and substituted for grate in the grate-kiln system. Thus, 20% of the investment could be saved. Production cost may also be decreased. The production of cold bonding pellets does not need additional area.

Jan 1, 1980

By Robert F. Kehrman

As part of the Bureau of Mines research on the In-Situ Uranium Leaching, various geophysical resistivity measuring techniques were -evaluated to identify a rapid reliable method for detecting the underground migration of lixiviant outside of the planned limits. Surface and downhole galvanic resistivity and controlled source audio-magnetotelluric (AMT) methods were tested at an in-situ uranium mine in Northern Wyoming during start-up of a new mining area. Downhole galvanic and AMT were the most promising techniques.

Jan 1, 1980

By A. Bruynesteyn

Results are presented from a series of tests designed to determine the beneficial effects of the microorganism Thiobacillus ferrooxidans upon the leaching of uranium from a pyritic uranium ore. Minus 1-inch (-25mm) 0.0711 percent uranium containing, pyritic ore from the Rio Algom Mine at Elliott Lake, Canada was leached with lixiviants of various Eh and pH as well as being subjected to a biologically-assisted ferric iron leach. In all cases, the biological leach gave superior extraction. At pH 1.6, the biological leach gave 100.6 percent extraction and the ferric iron leach 69.8 percent. This improvement in extraction is associated with a relatively rapid biological breakdown of the pyritic material, thus liberating uranium mineralization associated with these pyritic materials and regenerating the ferric sulphate lixiviant in situ.

Jan 1, 1981

By Subhash Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico. is a research and development project sponsored by the U.S. Department of Energy, designed to demonstrate the safe disposal of radioactive waste. A mine (repository) is being developed 2150 feet below the surface in a thick salt bed, which will serve as the disposal medium. The underground ventilation system for the WIPP project was originally designed based on a fixed project scope. The design criteria and ventilation requirements were developed for the performance of various activities as then envisioned towards the achievement of this goal. However, in light of new information and actual site-specific experience at WIPP leading to a clearer definition of the scope-related programs and activities, it was realized that the existing ventilation system may need to be modified. A re-assessment of the ventilation requirements--based on the current status of the facility and a clearer definition of the scope of the experimental programs, waste storage methodology, mine developmental activities. and current equipment list--indicates a two- fold increase in underground airflows from 210,000 cubic feet per minute (cfm) to 425,000 cfm. Various options to provide the increased airflow to the underground facility were considered and analyzed. Based on the techno-economic analysis, safety and environ- mental considerations, and other conditions unique to a facility like WIPP, it was decided to construct a new shaft to serve as the primary fresh air intake, along with the installation of additional fans in parallel with the existing set up. Low cost and the ease with which the new design could be implemented and integrated into the existing ventilation system with minimum impact on current activities and projected schedules were the guiding factors in designing the shaft and related ventilation modifications.

Jan 1, 1987

By J. Liniecki, w. Chruscielewski, T. Domanski

INTRODUCTION Mining is the Polish greatest industry employing about 350 thousand miners in more than a hundred underground mines. The mining regions are located mainly in the south of the country - see Fig. 1. [ ] The coal mining dominates, however, and the zinc-lead and copper-ore mines presently employ about 16000 miners. All these mines are rather deep and wet. Their drawing shafts are between a hundred to more then thousand meters deep. The cross-adit of working area of mines ranges from several kilometers to a few tens of kilometers. The numbers of mines per mine differ also considerably and depend on the territory and type of mines. The largest coal mines employ about ten thousand miners but the largest metal ore mines do not employ more than four thousand miners. In all the mines the electric motors or diesel engines are being used. The intensity of mine ventilation, characterized by the volume of fresh air injected in to the main ventilating shaft per miner and per unit of the power consumed by the engines is about 6 cubic meters per minute per man and per horsepower. The studies of the potential alpha energy of radon daughter products /RnDP/ could be divided into the three developmental stages: I-st - stage /1966-1970/ the stage of so called Pilot Survey. During this stage concentration of potential alpha energy of RnDP in the air was measured in selected typical mines in all mining regions of the country. II-nd - stage /1972-1974/ was the periodical control of concentration of potential alpha energy of RnDP in the air of zinc-lead and copper-ore mines which have been chosen and recognized during the first stage as being the most hazardous ones. Air-sampling system /ASS/ measurements were applied during this stage.

Jan 1, 1981

By N-h. Mao

We applied kriging (geostatistics) to interpret the structure of basement rock in Yucca Flat, NTS from borehole data. The estimation error for 118 data is 81 m comparable with those based on both gravity and borehole data. Using digitized topographic data, we tested the kriging results and found that the model validation process (Thomas option) on data gave a fair representation of the overall uncertainty of the kriged values.

Jan 1, 1985

By Kenneth Ronald Miller

Thunder Basin Coal Company&apos;s Black Thunder Mine is located 80 km (50 miles) southeast of Gillette, Wyoming in the Powder River Basin. Surface coal mining operations began in 1977. The Black Thunder Mine has been North America&apos;s largest producing coal mine for over 5 years. Production in 1988 totaled 22.6 million mt (24.9 million st) of sub-bituminous coal. Thunder Basin Coal Company is a subsidiary of Atlantic Richfield Company. The mine began as a truck-shovel stripping and mining operation. Haul trucks of 154 mt (170 st) capacity were part of the original fleet. In 1985, 218 mt (240 st) capacity trucks were introduced to the fleet. In 1988 a dragline was added for stripping. A single, primary/ secondary crushing stream feeds either a slot storage facility or dual silos. Three loading points are situated over two rail loops serviced by the Burlington Northern and Chicago North-western Railways. A Near Pit Crushing and Conveying system is currently under construction. It is expected to be completed during the fourth quarter of 1989. During the past 10 years, the conceptual crushing/conveying design has changed several times as technology and commodity markets have changed. The system under construction will have a capacity of 4700 mtph (5200 stph). The overland belt will be 3570 m (11,700 ft) long and 1800 mm (72 in.) wide. The belt speed will be 300 meters per minute (1000 fpm). Two separate crushing streams will feed the overland belt. Each stream will be comprised of a dump hopper at reclaim surface elevation, a drag feeder, a two-stage triple-roll crusher, and an incline conveyor of 2700 mtph (3000 stph) capacity. This article will describe the different concepts and factors that have resulted in the system design now under construction.

Jan 1, 1989

By Gregg Wilkerson

The Blind Springs Hill pumice beds are located 5 miles southwest of Benton, California in the foothills between the Benton Mountain Range and Blind Springs Valley. The best exposures of the pumice are in an area 0.75 miles west of Blind Springs Hill. The pumice is Quaternary ejecta material which came from the rhyolitic volcanoes in the Glass Mountain-Volcanic Tablelands area of Mono County. The pumice beds occur in two distinct layers separated by an unconformity. The upper layer is 0 to 11 feet thick and consists of coarse subangular pumice fragments, some of which are over 1.75 inches in diameter. The lower bed is medium to coarse grained with subangular fragments up to 1.0 inch. The lower bed is 0 to 9 feet thick. Overburden at the Blind Springs Hill deposit varies from 0 to 15 feet. There are approximately 1 million cubic yards of material in the deposit that can be mined. The size distribution in the deposit is mostly fine with only 10.6% of the pumice fragments being over 0.5 inch in diameter, the minimum size needed for stone-wash or acid-wash applications. Suitability of pumice for the textile industry is quantified by standard 15-minute abrasion and absorption tests. In the Blind Springs Hill deposit, the plus 0.5 inch fraction has an abrasion loss of 33% which is too high for stone-wash application but it has an absorption capacity of 36% which makes it suitable for acid-wash applications in the textile industry. The abrasion and absorption properties of this deposit are within the range of those which have been measured for other pumice deposits within the United States.

Jan 1, 1995

By R. M. Jacobs

Can your company afford to issue a check today for $100,000, $500,000, $2,000,000, or $22,000,000? This is what it might cost your company if it is on the losing end of a product liability suit. During the past 10 to 15 years, the number of product liability actions has grown from a handful per year level to a hundreds of thousands per year level. Settlements and awards in the tens and hundreds of thousands of dollars are not unusual in these days. The largest award that the authors haw heard about is a case involving a private airplane and the death of four men, which was awarded over $22,000,000. In the materials handling field, a fork lift truck, ordered with an overhead guard, was delivered without a guard because one was not available at the time. An accident with serious personal injury followed. Wouldn&apos;t it have been better to have waited until the guard was available before delivering the unit? Answer: a quarter of a million dollars better -- the cost of the settlement. Hoisting devices are also not without their liability precedents. In a 1960 case, an employee was injured when a load abruptly fell from a hoist. It was determined that the operator could not possibly have caused such a fall had the hoist been functioning properly. The case was compounded when the manufacturer of the hoist contended that the load had been improperly connected to the device, since the same hoist was used to remove the weight from the injured man without another malfunction.

Jan 1, 1973

By Spencer R. Titley

Porphyry copper deposits in the southwestern Pacific area represent relative newcomers to the growing number of occurrences of this mineral deposit type. In addition to firmly establishing the importance of this region and its potential influence within the framework of world copper resources, the deposits of this region are significant from a scientific point of view because of their close relationship to the phenomena of Island Arc evolution. Since the discovery of Panguna on Bougainville in 1964, the list of prospects, proven and unproven, and developments, has grown to more than twenty and the number continues to increase. At the time of this writing, the number of prospects is imperfectly known but the following localities and numbers are fair minimum approximations: Manus (Admiralty Islands) (3); New Britain (5); New Ireland (1); Guadalcanal (2); New Guinea Highlands (6); Misima (1); and Fiji (2); Proven prospects are present in the new Guinea Highlands (2); one deposit is being developed in Test Irian, and one orebody, on Bougainville, is in production. This summary paper concerns a discussion of some of the geological characteristics of producers, developments, and prospects on the Islands of Nets Guinea, New Britain, Bougainville, Guadalcanal, and Manus. I am not aware of publishable data for Misima or Fiji. As so many variables ultimately determine whether or not a porphyry copper occurrence becomes an orebody, not the least of which is geography, this summary treats the characteristics of these occurrences which alloy; their assignment to the porphyry copper category. For purposes of this discussion, I have considered those copper occurrences which are apparently genetically related to talc-alkaline intrusions and in which the content of copper has been upgraded 50 to 100 times the Clarke for that particular host rock. Some of these occurrences are shown on Figure 1.

Jan 1, 1973

By C. K. Skokan

Various geophysical tools have been tested over the last eight years to evaluate their usefulness in defining damaged rock zones in an underground facility at the WIPP site in New Mexico. These tools include direct current and frequency domain electrical methods and seismic tomography. The electrical measurements show a "drying rind" to exist around older excavations. Seismic tomography confirms that a rind of lower velocity has developed along walls. In combining these tools, a monitoring program has been proposed to observe long-term changes in bedded salt. Results from the monitoring of electrical data over a 2-year time period illustrate the applicability of the technique in an underground environment.

Jan 1, 1993

Since 1992 the Grasberg Mine, located in the remote regions of Indonesia, has utilized the Modular Mining System. Over the last several years, major steps have been taken to maximize this productivity enhancement system. These steps include; the Automated Lineup, the Linear Program upgrade, tracking of Mean Time Between Failure, a MEDS system interface, a VMIS system interface, and implementation of the new Graphical Operator Interface Console with Global Positioning, This application of new technology and innovation has lead to improved performance, understanding and reporting, as well as the quality of the Indonesian Engineers. These efforts have contributed 10 Grasberg achieving one of the lowest mining costs in the copper industry.

Jan 1, 1998