Search Documents

By William A. Wallace

Common mineral resources (sand, gravel, crushed stone, etc.), which are so necessary for the construction of metropolitan areas, are rapidly being depleted or otherwise rendered unavailable in the very areas that need them most. However, the problem of planning for these resources involves a number of independent and dependent variables that must first be defined and related. Finally, a dollar value must be assigned where possible. Complex interrelationships between the variables and their dependence on outside factors has made mathematical "solution" of the problem of planning for non-renewable mineral resources difficult at the present time. Therefore, the use of computer simulation is suggested as a means by which this complex problem can be investigated. The purpose of this paper is to report on a continuing research program whose objectives are: (1) to delineate the factors involved in planning for the utilization of common mineral resources in urban-suburban environs; (2) to construct a planning model for these materials amenable to computer analysis, (3) evaluate the model by using test cases, and (4) perform a sensitivity analysis to determine the initial parameters in future planning for these materials.

Jan 1, 1968

By Vijenac Quarry, A. Iljazagic, t. Knezicek, T. Omeragic

Limestone quarry Vijenac, is one of the key limestone producers in B&H. Conventional massive drilling and blasting is the technique applied for limestone exploitation. Utilized blasting scheme causes appearance of large oversize stone pieces, uncontrolled flying stone and undesirable seismic effects. In order to reduce or eliminate exposed disadvantages and to improve environment in the area of Vijenac quarry, an innovative blasting scheme was tested. Conventional blasting scheme was changed from single row, deep inclined blast holes combined with two lines short horizontal holes to multi row, inclined blast holes combined with a single line short horizontal blastholes. Applied innovative blasting scheme reduces negative blasting impact on the environment through safer working conditions, reduced amount of dust after blasting, reduced explosive and energy consumption, reduced appearance of explosive gasses and reduced earth and air vibrations as the result of seismic effects.

Jan 1, 2005

By Michael Li, Kathryn Rogers, Arie Moerman, Mike Cooper

The Brunswick Mine, a Division of Noranda Inc., produces zinc, lead, copper, and bulk lead-zinc concentrates through underground mining of a large massive sulphide deposit. The mining method employed is longhole open stoping with delayed backfilling. In 1996 Brunswick began a review of its mining methods and backfilling operations. In 1997 the decision was made to convert the backfill system from cemented and uncemented rockfill to paste backfill prepared from mill tailings. This paper will describe the features of the backfill preparation and distribution systems, review the handling of technical issues, and discuss experiences since plant commissioning.

Jan 1, 2001

By M. G. Mudrey

Considerable potential for metallic mineral resources in the lower Proterozoic rock of the Lake Superior region exists (Mudrey and Kalliokoski, in press). Most of the identified resources occur within a 2.0- to 1.9-b.y.-old lithotectonic assemblage characterized by extensive sedimentary strata in the north and thick volcanic se- quences in the south, all deposited on a two-terrane, composite basement of Archean age (DeMattis, 1989). Since the late 1960s, measured resources of nearly 90 Mt (100 million st) of typical volcanogenic massive sulfide at eight localities in Wisconsin have been discovered. The largest of these, near Crandon, contains about 61 Mt (67 million st) of ore averaging 5.6% zinc, 1.1 % copper, and 0.5% lead. Although none of these properties are in production, estimates by Mudrey (1978) suggest that Wisconsin could become a major contributor of newly mined zinc and copper in the United States. These discoveries and uranium and gold discoveries in the Canadian Precambrian are what have led to in- creased metallic mineral exploration throughout the northern half of Wisconsin (Fig. 1). In this chapter, we discuss the geology and legal framework in which the Proterozoic volcanogenic massive sulfide deposits were found. Exploration activities for other metals have generally been negative, and have been background noise for the legislative activities related to the massive sulfide discoveries. Uranium exploration has been consistently negative, although several different environments have been assessed. Other metal discoveries. such as titanium/vanadium, have been subeconomic.

Jan 1, 1991

By G. Blackwell, E. Bozorgebrahimi

The trend in open pit mining has been to maintain cost competitiveness through economies of scale, particularly by implementing larger trucks and shovels. This paper considers the potential adverse impact of such scale adjustment, however, on dilution, maintenance, flexibility, and other aspects of operations. It examines the mine production characteristics affected by increased equipment size and attempts to quantify the impact on the overall operation. Reference is made to data from operations that have experienced a variety of equipment size ranges changes over the last decade.

Jan 1, 2003

By Aarne Visnapuu

Unmodified pneumatic rock drills may have noise levels of 115 to 130 dB at the operator's position. Experimental modifications have been made to a standard drill to suppress the noise from the three main sources: the air exhaust noise, the noise radiated from the drill, and the resonance noise of the steel drill rods. A prototype model developed at the Bureau of Mines, Rolla Metallurgy Research Center, operates at a noise level below 100 dB. A close-fitting case and muffler unit, consisting of a metallic skeleton filled with viscoelastic absorber and having a durable cover, provided both muffling and noise absorption. Damping alloys were used at strategic points in the drill. Drill steel resonance noise was reduced by a constrained-layer treatment on the outside of the drill rod. The singular and combined effects of the treatments are presented in detail.

Jan 1, 1973

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A three-stage fluidizing-bed process consisting of chlorination, selective oxidation and sulfur chloride conversion was tested for processing chalcopyrite concentrate. It was found that the use of excess oxygen was essential for the stable operation of the oxidation reactor. The excess-oxygen gas inevitably causes the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and selective oxidation steps with separate flow paths of the fluidizing gases, thereby, preventing the passage of excess-oxygen gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratoryscale fiuidizing bed setup.

Jan 1, 2002

By Terry P. McNulty

During the last 30 years, at least ten authors have dealt with startup ("ramp-up') times for minerals beneficiation, hydrometallurgical, and/or pyrometallurgical plants. Most have attempted to identity the reasons for delays and some have suggested attributes common to successful startups, as well as those shared by unsuccessful ones. The most recent has advanced a project characterization matrix as a predictive tool for qualified users. This paper will summarize past work, will review cause and effect, will outline an approach for refining our ability to avoid costly delays, and will seek guidance from professionals most likely to use such a tool. INTRODUCTION During the last few decades, many billions of dollars have been lost by investors in mineral industry projects that did not perform as well as their developers had hoped. The most common form of failure has been the inability to generate a profit quickly, and delayed achievement of planned production rate has been the chief cause. Minerals processing projects are by no means the only kind of plant to suffer from startup delays, as some authors cited in this paper considered inorganic chemical plants and other types of facilities. Furthermore, mines are not without fault and there have been many that were closed after years of disappointing performance. However, our interests as a group are most sharply focused on mineral processing and our database for such projects is relatively extensive. It is sufficient to say that the conclusions made or repeated in the following text can be readily extended to most types of projects.

Jan 1, 2004

By Fiona M. Doyle, Christopher R. Lubeck, Michael C. Chin

The fundamentals behind a novel approach for creating inorganic/polymer hybrids are described. The binding of +2 charged ions, specifically Cue-and Cat+, to ionic functional groups is explored through UV-Vis spectroscopy and zeta potential measurements. The novel approach uses an electric field to drive ions into a functionalized polymeric matrix, thereby inducing the precipitation of calcium phosphate species. Scanning electron microscopy images of the resulting composite illustrate the results of these precipitations with two distinct morphologies observed.

Jan 1, 2003

By W. M. Lewis

Product losses to tailings ponds have long been a source of frustration for the mining and utilities industries. The utilization -of the Lewis Econosizer to recover lost products has proven to be very cost effective through reduced acreage requirements, cleaning costs and increased production. The unit is successfully operating in coal, aggregates, industrial minerals, clay, fly ash, heavy minerals and many other ores. Utilizing an upward flow of slurry in a free settling environment, particles stratify within the unit according to settling velocities and are removed as sized products. Ultra fines or clarified water is removed off the top of the unit. The Econosizer requires no power and only minimal maintenance.

Jan 1, 1998

By Behzad Khorshidi

"The ultimate objectives of the post-tensioned strands are to connect the precast segments into a ring and provide pre-stress in the tunnel circumference. The method involves inserting the strand through the preliminary embedded duct in the precast concrete segments and then tensioning the strand by jack and fastening it. The post-tensioned strand eliminates the necessity of bolt connections between the segments and may reduce the labor cost and increase speed of lining construction. Pre-stressing of the segmental lining reduces the steel reinforcement or fiber volume in precast segments and/or thickness of the precast segments which would result in reducing the manufacturing cost of them. Pre-stressing would reduce cracking and increase water tightness, and would provide smooth intrados due to eliminated bolt joints and pockets in the tunnel lining. Pre-stressing would increase resistance to internal pressures as well. Further, this system could work very well structurally in tunnels with squeezing rock or tunnels with high seismic loadings. INTRODUCTION OF THE METHODPost-tensioning is commonly used in the construction of bridges, large buildings, nuclear power stations, and water tanks but its utilization in tunnels is still in its infancy.The precast pre-stressed concrete segmental lining can be used for shield tunnels. It provides a reinforced lining ring by the following construction stages and as shown in Figure 1:1) Segments to be assembled by TBM to complete a full ring2) Steel strand to be inserted through embedded duct (sheath) within the segments3) The strand to be tensioned by Jack after anchorage of the other end4) The strand to be fastened after reaching required tension load5) The horizontal strands (if necessary) to be installed, tensioned and fastened6) The recesses and gap between strand and duct to be filled by groutingFurther, Figure 2 shows an unbonded post-tensioning strand model; Figure 3 shows an anchor sample (Xanchor); Figure 4 shows a duct (sheath) and anchor within reinforcement; Figure 5 depicts the posttensioning of a strand by jack; and Figure 6 is an image of the Midorigaoka Trunk line tunnel in Sagamihara, Japan which was constructed using this system."

Jan 1, 2016

By G. H. Schnakenberg

In 1986, the US Bureau of Mines (USBM) embarked on a major research effort to develop technology that could substantially reduce worker exposure to face hazards by simply relocating the equipment operators to an area of relative safety. This reduced-exposure mining system (REMS) research effort enhances the USBM's ongoing health and safety efforts aimed at reducing and controlling dust and noise and reducing accidents through training and better mining practices. This paper reports on the progress made on the developing research and demonstrates the technologies required for the computer-assisted teleremote operation of continuous mining machines, haulage systems and roof bolting machines.

Jan 1, 1997

By L. P. Meade

Dimension stone and salt are two of the oldest industrial minerals utilized. Salt has been and still is a necessity to the well being of man. Dimension stone on the other hand has been utilized by man to glorify conquests - both in the battlefield and corporate arena. Both commodities are important, but dimension stone has an additional use in that the survival lessons learned by the domestic industry can be applied to other contemporary industrial minerals, Specialization in the market place and customer service have allowed domestic producers to survive: subsidized foreign competition, obsolete equipment, and lack of capital.

Jan 1, 1986

By John D. Rockaway

This report and accompanying engineering geologic map describe the generalized engineering geology of St. Louis County, Missouri for use in determining the most efficient, economical, and environmentally sound program for land development and urban growth. It includes an evaluation of such factors as the physical and engineering properties of soil and bedrock, surface stability, and subsurface geologic structure. The map and text are designed primarily for property owners, engineers, architects, real estate developers, and city planners involved in land-use planning. The geologic information and engineering interpretation must be considered as a general guide and not as a substitute for a complete on site investigation prior to initiation of any land-use project. The map scale, 1:63,360 (1 inch to a mile) is too small to include the detailed information normally provided on the 7 1/2-minute quadrangle series (1:24,000). The smaller scale is most useful at regional planning levels and was chosen to present information on the more significant engineering factors of the geologic environment for county-wide planning and development. A conventional geologic map deals primarily with the distribution and variation of bedrock formations, and a pedologic map presents information on the soil or natural medium for plant growth. Basic geologic maps and pedological maps are valuable tools that can be of assistance in studying the geologic environment, however, these maps do not provide all the information required for land-use planning. The engineering geologic maps are designed to provide this data. The engineering geologic map is related to both of these basic maps but emphasizes the engineering properties of the rock formations and soils rather than their age or origin. Some of the unit boundaries shown on the county map will closely follow some geologic formation and/or pedologic boundaries; others will transgress these conventional boundaries. Earth materials, bedrock and soil, that have similar engineering characteristics have been mapped as one unit without regard to their geologic or pedologic classifications. This is to assure that geological factors are recognized, adequately interpreted, and presented for use in engineering practice.

Jan 1, 1970

By J. D. Mc Beth

The Carlin Gold Mining Company, a wholly owned subsidiary of Newmont Mining Corporation has been successfully operating an open pit gold mine and cyanide mill for approximately the past ten years. It is a unique operation in that about 20 percent of the mill feed is a carbonaceous ore refractory to cyanidation that must undergo a pretreatment stage developed for, and by, Carlin. The mine and plant are located in the Tuscarora mountain range is north-eastern Nevada near the towns of Carlin and Elko. Claims were staked at the minesite in 1961 and 1962. A drilling program was initiated late in 1962 and after drilling a total of 250,000 feet of rotary drill holes an estimated 9,300,000 tons of ore at a grade of 0.32 ounces of gold per ton was delineated.

Jan 1, 1975

By M. K. Buder

Over the years, electric utilities have been faced with declining steam-coal quality, rising coal prices, and increasingly rigid and costly environmental standards. As a result, many utilities are beginning to show an interest in coal cleaning to upgrade coal by improving its heating value and reducing its sulfur content. Among the primary questions that must be answered for these electric utilities is whether the cost of coal cleaning can be offset by the potential cost savings in coal transportation and utilization in power generation. In search of at least a preliminary answer to this question, the Electric Power Research Institute (EPRI) engaged Bechtel to perform a case-by-case economic study to examine the cost effects of using cleaned versus raw coal to fuel new electric power plants. The results of two of the seven cases studied which involved western coals - one from Montana and another from Utah - are reported in this paper. Coal cleaning appeared to be a cost effective option for the Utah coal, but only marginally economical for the Montana coal. These cost results are expected to change to favor coal cleaning to a greater extent with the application of the final revised New Source Performance Standards regulating SO2 emissions just issued by the EPA. The study was based on the regulation originally proposed by the EPA under the 1977 Clean Air Act Amendments.

Jan 1, 1979

By W. E. Lamont

As part of its program to minimize mineral and metal needs, the Federal Bureau of Mines conducted investigations to determine the feasibility of producing foundry-sand-grade olivine concentrates from low-grade sources. Using a Bureau-patented attrition-grinding technique, concentrates meeting Steel Founder's Society of America (SFSA) specifications for loss on ignition (LOI) were prepared. Studies showed that green strengths and tensile strengths of the attrition-ground olivine were equivalent or superior to those of commercial materials. Metal-casting studies showed that molds of attrition-ground olivine produced better surface finishes. The improved surface finishes were attributed in part to increased grain sphericity.

Jan 1, 1977

By J. Duran

Mining at Phoenix is currently done by surface operation in the Fortitude and Bonanza Pits, at a combined rate of approximately 110,000 tons per day. A portion of the ore bodies targeted by these pits was mined previously by underground mining methods, dating back to the mid to late 1800?s. Most of the underground workings (voids) are located in the west central area of the Bonanza Pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This paper presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

Feb 23, 2014

By M. E. Breitrick

Newmont Gold Company began full production in early 1995 at the Carlin East underground mine. The mine is currently producing at the rate of 900 tpd (1.000 stpd). for an annual production of 150.000 ounces. Approximately one hundred twenty five hourly and salary personnel are employed at the project for the estimated six-year mine life. Two mining methods are currently utilized at the mine. Longhole stoping with cemented backfill accounts for 70% of the total mine production. Conventional underhand drift and cemented fill accounts for the balance of the daily tonnage. In December 1996. Newmont purchased a new AC-Eickhoff ET-210 Roadheader. The machine went into service in mid-June of 1997 and is used in both longhole stope topcut development and cut and fill production at a rate of 225 tpd (250 stpd). The Carlin East mine is operated by Newmont Gold Company. The mine is one of four underground gold mines in production in northeastern Nevada owned by Newmont Gold.

Jan 1, 1998

By H. Weber

This paper is in three parts. Part I discusses the various types of cement clinker coolers now in full-scale operation. Part II is a detailed study of the criteria for selection of the type of cement clinker cooler best suited for a given installation. Part III covers a number of cooling problems and their solutions in some of the metals industries. The large and world-wide problem of cement clinker cooling has motivated much study and development and the coverage here of this work is somewhat detailed. In contrast the cooling problems of the metals industries are quite varied between industries and often quite different from plant to plant in the same industry because of basic differences in the requirements of the particular material being processed. Therefore the coverage of metals industries coolers is somewhat more general. It is believed that all of the technology covered here may be of interest to those working with the problems of cooling hot materials.

Jan 1, 1980