Search Documents

By M. S. Klima

This paper will detail the work that has been done in 1990 and 1991 at the Pittsburgh Energy Technology Center (PETC) on the development of the U.S. Department of Energy's (DOE) patented Micro-Mag Process. This process entails the use of a micronized-magnetite (minus-10 microns) and water mixture for cleaning fine coal (minus-600 microns) in a cyclone, along with the production and recovery of the magnetite. Emphasis will be on the results from micronized-magnetite recovery testing using both conventional wet-drum and high-gradient magnetic separators in which several key operating conditions were varied including feed percent solids, magnetite-to-coal ratio, magnetite grade, and feed rate. Also presented will be selected results from testing done on a 76-mm diameter cyclone at a relative density of 1.50 showing the effects of operating pressure, magnetite grade, and medium-to-coal ratio on separation efficiency. In addition, two methods for producing micronized magnetite, along with the corresponding size distributions, will also be discussed.

Jan 1, 1992

By J. G. Groppo

In 1992, 48 million tons of fly ash (not including bottom ash, boiler slag and FGD material) was produced in the United States, according to the American Coal Ash Association. Of this amount, 27.2% was utilized; although the percentage of fly ash utilized increased from 20% in 1980, there is significant potential to increase utilization. One of the primary driving forces behind increased utilization is increased disposal costs due to more stringent environmental controls and regulation. Fly ash is classified as a natural pozzolan and finds significant use as a cement additive. It has been found to increase the plasticity of the cement mixture while lowering the amount of mix water needed. In addition to improving leveling and finishing properties, fly ash improves pumpability as well as decreases the heat of hydration of the concrete mix which is particularly important in massive concrete structures such as dams where the concrete needs to cool as quickly as possible. The Loss on Ignition (LOI) of fly ash is an important quality when considering utilization. The LOI is primarily due to the presence of unburned carbon and the standard specifications for the use of fly ash as a mineral admixture in Portland cement concrete are given in ASTM C618-89a. which sets an LOI limit of 6%. However, many states have set a more stringent limit of 3%. The primary reason for the lower LOI specification is that carbon adsorbs air entraining agents which limits freeze-thaw resistance. This is particularly important in climates such as the midwestern US where multiple cycles of freezing and thawing are typical in winter.

Jan 1, 1995

By Manuel Gomez

This, report presents correlative data on ash and sulfur forms for Pittsburgh seam coal from Greene County, Pa. Prediction equations were developed for sulfur form distributions and washability characteristics. The equations developed were evaluated with an independent set of exploration core samples. It was demonstrated-that both sulfur distributions and washability characteristic's can be predicted from exploration core data ahead of mining. This information can improve the efficiency of selective mining techniques for the production of a uniform metallurgical coal product.

Jan 1, 1967

By Arland R. Krueger

You have asked me today to tell you how quarried stone is meeting the challenges of contemporary architecture. The new position of stone, the oldest building material, in contemporary architecture, was described to me very concisely the other day by a very distinguished avant garde architect. He said rather wryly, "Do you know, if quarried stone had only just been discovered, we would all be calling it the most miraculous of all the modern miracle building materials." His prognosis was, I believe, much more than a witty quote. It echoes the surprise and. enthusiasm with which a considerable segment of the architectural profession is rediscovering stone as a most modern building material that offers unsurpassed values in beauty and practicality - well deserving of the term "miracle".

Jan 1, 1960

By Michael Edesess

The salt gradient solar pond has been the focal point of accelerating international attention and interest in recent months. Only recently have most investigators in the renewable energy field come to realize the versatility of the solar pond, and its ability to overcome certain problems usually associated with solar technologies. These realizations, together with clear demonstrations in Israel and elsewhere of its technical feasibility, have combined to bring the solar pond to the forefront of renewable energy technologies. The solar pond is a natural or site-built pond, about one to five meters or more in depth, which has been altered to retard the loss of absorbed solar energy. The absorbed solar energy is usually lost through upward buoyancy of the warmed water, followed by the loss of its heat to the atmosphere. The chief solar pond technology -the salt gradient, or "nonconvective" solar pond-prevents this upward buoyancy by means of a vertical density gradient achieved with dissolved salt. The deep waters in the solar pond reach high temperatures, up to and even above the boiling point of pure water.

Jan 1, 1981

By C. A. Rowland

When studying the feasibility of using autogenous or semi-autogenous grinding, operating and engineering companies frequently request assistance from the mill manufacturers in three areas - 1. Recommendations for studying the suitability of autogenous or semi-autogenous grinding for the specific ore. 2. Mill sizing, to accomplish required grind. 3. Recommendations on mill design and operation. Rod mills and ball mills are selected by the use of bench scale standard grindability tests and established calculation procedures, of which the most frequently used are the Bond Grindability tests and the Bond Work Index equation(1). The accuracy of these have been reviewed by C. A. Rowland in his papers, showing the correlation of work indices calculated from plant operating data and laboratory grindability tests(2)(3). The selection of autogenous and semi-autogenous primary mills has not reached the stage where mill size selection can be made from bench scale tests. Considerably more extensive testing will be necessary than required for selecting rod mills and ball mills.

Jan 1, 1974

By K. Zabrusky

Epithermal vein systems are often modeled as simple, discrete high grade structures within low grade host rock. However, geologic setting and structural preparation influence how such vein systems form. In structurally complex areas, veins may follow several structural trends and occur on a variety of scales. Geologic and grade modeling within such complex structural regimes can be difficult as individual veins cannot be delineated from host rock based on grade alone. Structurally complex areas require a different approach than traditional discrete vein modeling. Presented herein is a study of a structurally complex area that hosts vein mineralization to be mined underground. All veins could not be modeled discretely, so an alternate approach was needed. Major structures were modeled using surface and underground mapping and were then used to create a structural trend for the area. This trend was used to guide 3D grade shell construction. The grade shells replaced 3D vein solids for grade estimation in order to mitigate the influence of high grade samples. Structurally guided grade shell construction offers a more effective modeling method than discrete vein modeling in deposits that are structurally complex.

Feb 23, 2014

By S. A. Rholl

This paper describes the Bureau of Mines experimental test program which evaluated the effectiveness of using high explosives to enhance orebody permeability. To determine the effect of stress on the fracture network generated by blasting, fifteen single-hole laboratory tests in granite blocks up to .067 m3 (2.4 ft3) in size were blasted using .12 to .20m (4.8 to 8.0 in) of 1.6xl0-3-, 3.2xl0-3-, or 6.5xl0-3-kg (25-, 50-, or 100-grain) detonating cord. In situ stresses were simulated using polyaxial load cells to apply uniform stresses of 1.72xl06 to 1.76xl07 Pa (250 to 2550 psi). All of the blocks were sawed to expose the blast-induced fracture patterns for analysis.

Jan 1, 1991

By E. J. Freech

In this part of the two-part paper we discuss briefly the adaptation of the comminution model to describe the observed behavior of an industrial grinding circuit. Although reported verification of comminution models for continuous systems is limited, some interesting work has been reported 1,2 recently. The data acquisition and modeling efforts are described first, followed by discussion of some of the simulation results. Observations pertinent to steady-state operation are presented followed by a description of the application of a dynamic model of the grinding circuit for synthesis and evaluation of grinding-circuit control. The pilot-scale work indicated the comminution model should be capable of describing an industrial size-reduction process. Recognizing the broad utility of a process model based on first- principles, the Industrial Nucleonics Corporation of Columbus, Ohio, embarked on a joint program with the Duval Corporation of Tucson, Arizona, to evaluate the industrial applicability of the models described in Part I. This program was conducted in a grinding circuit, which included a rod mill 12.5 feet in diameter and 16 feet long and a ball mill 12.5 feet in diameter and 14 feet long, at Duval Corporation's Esperanza property3. The rod mill was operated in open circuit and the ball mill in closed circuit with cyclone classifiers.

Jan 1, 1970

Many investigators believe that column flotation cells offer significant advantages over standard mechanical machines for the flotation of fine particles. However, because of their unique design and operation, conventional techniques for flotation cell scale-up and design cannot be applied to columns. In an attempt to help alleviate this problems a population balance model based on first principles has been developed for fine particle flotation in a column. Two different terms have been considered in the model, i.e., transport and rate. Transport terms, incorporating fluid flow and bouyancy, are used to describe the movement of air bubbles, unattached particles and bubble-particle aggregates along the length of the column. Rate terms, which describe the bubble-particle attachment process, have been derived from first principle considerations. Because the model is based on first principles, it can be useful for the design, control, optimization and scale-up of column flotation cells.

Jan 1, 1987

By Robert J. Timko

New methods of reducing stopping leakage have been investigated by Mine Safety Appliance Research Corporation, working under contract to the U. S. Bureau of Mines. It was found that proper construction techniques are far more important in reducing leakage than the type of sealant used, provided the sealant has sufficient adhesion and strength. Leakage could also be substantially reduced by brushing on modified mortar sealants rather than using the accepted method of trowelling them on.

Jan 1, 1982

By Verne Huser

The intensity of environmental conflict, the delays and legal battles that have marked the 1970's suggest the need for additional processes to resolve environmental disputes. Our present means frequently fail to address the real issues separating individuals and institutions. They are primarily adversary processes that foster polarization and reduce cooperative efforts. At the Office of Environmental Mediation, we have no quarrel with adversary processes nor with polarization, for both serve as important spurs to necessary change. We do seek cooperation among parties at a point where there can be a realistic expectation of success in facilitating a resolution of their mutual differences.

Jan 1, 1979

By J. Drelick

Among the wide variety of modern surface chemistry analytical techniques, contact angle measurements still remain attractive for wetting characterization of solid surfaces. The captive-bubble and sessile-drop techniques are the most popular methods for the examination of flotation systems. Systematic measurements of advancing and receding contact angles for several three-phase systems using the captive-bubble and sessile-drop techniques show that the contact angle measurements depend on the technique used and may differ significantly for some heterogeneous and rough solid surfaces. Importantly, it was found that these discrepancies in contact angle measurements depend on the bubble (drop) size. Contact angles as measured with the static captive-bubble technique are compared with those measured with the dynamic captive-bubble technique, in which the capture of a bubble at the solid surface results after buoyant transport and attachment The dynamic captive-bubble technique allows for the formation of much smaller bubbles than is possible with the static placement technique in which a bubble is placed at the solid surface with a microsyringe. Although this dynamic technique cannot be recommended for the systematic wetting characterization of solid surfaces, its significant advantage is the ability to examine the contact angle/bubble size relationship over a wide range of bubble sizes, from several micrometers to several millimeters in diameter.

Jan 1, 1995

By J. V. Bymark

It is the intent of this paper to discuss the autogenous grinding circuit at Hibbing Taconite. The scope of the presentation includes; a brief history, the process flowsheet and the steps taken to improve mill productivity, availability and metallurgical performance. Hibbing Taconite is located near the center of the Mesabi Range in Northern Minnesota 100 miles from the Canadian border and 80 miles north of the Lake Superior Port Cities of Duluth and Superior. A 105 mile railroad connects us with the port of Superior, Wisconsin, where our pellets are loaded into lake carriers for lower lake destinations. It is worthy to mention the Mesabi Range's most famous landmark which is immediately to the south of our mine area. This is the Hull Rust Mahoning Mine which operated until the mid-1970's producing more than 700 million tons of red ore between 1893 and 1973.

Jan 1, 1985

By S. M. Robinson

Wollastonite is recognized as one of the most unique, non-metallic minerals in the world. Its history for use in industrial applications is recent compared to other minerals, however, its distinctive physical properties, such as acicular particle shape, and alkaline pH creates incorporation possibilities ranging from bowling balls to automotive fascia, from ceramic tiles to automotive brakes, and from thermal insulation board to industrial and trade sale coatings. Its future use will be impacted by the exploitation of deposits which will ensure maintenance of the acicularity and purity of this naturally occurring mineral. Additionally, closely held surface treatment technology will open up additional niches requiring highly engineered performance.

Jan 1, 1995

By Guangyao Si, Ismet Canbulat, Xun Luo, Yi Duan

Routine analyses of seismicity and event locations are essential for coal burst risk management, especially in the presence of unfavorable and complex geology. In an Australian longwall coal mine, a small-scale seismic monitoring network was installed to monitor a section of a major dyke intersected by the roadway, which was classified as a coal burst prone zone. The Deep Convolutional Neural Network (DCNN) technique was adopted for automatically discriminating seismic events to assess seismicity in this zone. The discriminated seismic events were located with the Shortest Path Method based on the Boundary Discretization Scheme (BDS-SPM) for temporal-spatial seismic event distribution analysis. The results demonstrate that the seismic events are discriminated with an average accuracy of 94%. Moreover, the seismic events are more accurately located using the BDS-SPM with a 3D heterogeneous velocity model compared with results obtained with a homogeneous velocity model. The temporal and spatial variances in seismic activities identify that the rock fractures in the dyke zone are closely related to the longwall mining process and a local dyke has a controlling influence on the stress concentration in its vicinity.

Apr 26, 2022

By Greg Border

Many unique ventilation problems have been faced as Avery Island Mine's large openings have been mined. High humidity of outside air combines with the hygroscopic salt to create a corrosive atmosphere. Massive rooms preclude routine use of brattices to direct air flow to the working faces. Large amounts of explosives are consumed in single blasts. Resulting concussion pounds air control structures and ANFO ignition creates large amounts of nitrogen dioxide in single rooms. Geologic constraints confine new shafts and slopes to areas thought to be free of potential ground water hazards. Dust control techniques are limited by dry product demanded by customers. The Avery Island Mine's ventilation system has evolved to deal practically with the conditions and to dependably provide fresh air to the miners. International Salt Company's Avery Island Salt Mine, a multiple level room and pillar operation, has been mined steadily since about 1900. It is known as one of the "Five Island" salt dome mines of South Louisiana's Gulf Coast. Production from the area places Louisiana first in United States rock salt mined tonnage, according to the United States Bureau of Nines, 1982 (1). International Salt Company is a major force in U.S. salt production, as it also operates mines in Detroit, Michigan; Cleveland, Ohio; and Retsof, New York; a solar salt facility in Bonaire, Netherlands Antilles; and a solution mining plant at Watkins Glen, New York.

Jan 1, 1983

By J. A. Domenico

A safe and precise mineral separation alternative to heavy liquids is being used for mineral sands exploration on large scale orebodies. The separation process, Magstream®, uses ferro-fluids and magnetic and centrifugal forces to produce precise split points over a range of specific gravities from 1.5 to 18.0 g/cc. This paper describes a commercial scale exploration program treating, roughly, 90 samples per day in Senegal (West Africa). Separation results comparing Magstream® and conventional heavy-liquid separation are presented.

Jan 1, 1994

By A. E. Jack Swanson, Brian P. Micke

INTRODUCTION Nevada Goldfields began underground mining development at the Kingston Project in September, 1986, followed by mill start-up in March, 1987. The first gold pour in April followed three years of preparatory work in establishing a North American operational base for the production of precious metals by Golconda Minerals N.L., an Australian mining firm. GENERAL CORPORATE BACKGROUND The Golconda Group of companies was established in early 1983 in Australia. It began operations by successfully retreating tailings at several old gold mining sites throughout Australia. With the limited reserves available for tailings retreatment, Golconda began to look toward the future by conducting a gold exploration program in Australia. However, the continued high price of gold in Australia had limited the possibilities of acquiring good properties at a reasonable cost and consideration was given to looking outside Australia in addition to Golconda's domestic exploration activities. North America was favored because of the proven potential for substantial gold deposits, the established infrastructure which would allow for rapid and cost-effective development of new projects and the advantages of similar political and economic climates. In mid-1984, Golconda established an office in California and began an extensive study of over 100 prospects throughout the United States. Two prospects were identified as a result of this study whch showed merit; one was located at Empire, Colorado and the other at Aurora, Nevada. Negotiations were then successfully undertaken to acquire these two properties. Golconda's U.S. offices were moved to Reno, Nevada in early 1985 to facilitate management of its projects. To operate and manage these projects, a small Canadian company listed on the Vancouver Stock Exchange, Cannon Minerals, was acquired by Golconda and renamed Nevada Goldfields Corporation. The current structure of the company is shown below in Figure 1. A private placement of 2,575,000 shares of common stock at US54.00 per share was arranged by Jacksons Limited of Australia in association with W.I. Carr (U.K.) Limited of London. This placement resulted in US510.3 million being available in May, 1986 for the acquisition and initial development of the Aurora and Empire projects. While the financing was underway, project planning commenced on both the Aurora and Empire projects. The Aurora project was selected as the one to be initially developed because of its relatively advanced stage of development. The

Jan 1, 1987

By James McManus

The Lornex mine is located on the Southern slope of the Highland Valley in South Central British Columbia. The large low grade deposit was discovered in 1964; stripping began in 1970, and the mill started commercial production in October of 1972. The orebody is classified as a complex porphyry type having as major constituent quartz diorite, with varying amounts of quartz, grano diorite, and porphyry. A substantial degree of alteration is evident in the host rock, and this became the key factor in major equipment selection for the grinding section. A pilot plant was constructed on the property capable of treating 100 TPD of ore. The ore was mined to be as representative as possible of the entire orebody by sinking a shaft and cross cutting the deposit underground.

Jan 1, 1975