Search Documents

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

By R. D. Wunder

The Chino Mines Company, a Kennecott-Mitsubishi partnership, located in Hurley, New Mexico, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/ concentrator modernization commenced in 1980 and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34.0 kt/d (37,500 stpd). A new concentrator was constructed near the mine using semi-autogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of salable copper.

Jan 1, 1985

By William Gleason

"Modern society demands much more from the mining industry than just the raw materials it produces. In addition to providing copper, gold, coal and other minerals that make society function, the industry must conduct its operations in a safe and environmentally sustainable manner. This includes the equipment used and the engines that power the machines.In the United States, Tier 4 diesel engine standards that were set by the U.S. Environmental Protection Agency (EPA) are the strictest emissions requirement for off-highway diesel engines. This requirement regulates the amount of particulate matter (PM) and nitrogen oxides (NOx) that can be emitted from an off-highway diesel engine. In Europe, the Euro V standards are driving technology advancement in the sector.The European Euro V standards are required for new equipment manufactured beginning in January 2019. U.S. Tier 4 standards for heavy-duty off-road engines came into effect with model-year 2014 vehicles and equipment. China 6 standards come into effect in July 2020. India’s Bharat Stage VI standards will take full effect in 2020, and the phase-in of BSVIcompliant clean fuels began in April 2018.Caterpillar, Cummins and MTU are three of the leading manufacturers of engines for the mining sector. Each company is working toward creating efficient engines that can function in the often harsh environments found at openpit and underground mines around the world. In short, society is placing demands that are challenging engine manufacturers to deliver a product that can do more work while consuming less fuel and emitting fewer emissions.Technologies range from selective catalytic reduction (SCR) and diesel particulate filters (DPFs) to other engine strategies and emissions control technologies, which deliver near-zero black carbon and nitrogen oxide emissions, and lower greenhouse gas emissions. Caterpillar’s investmentCaterpillar, the world’s largest producer of mining equipment and mining engines, has been at the forefront of the changing demands placed on the industry and has remained on the cutting edge of engine development over the years, thanks to its investments in the sector.“Caterpillar made the choice to fund major engine and machine development work — even during a deep trough in the mining industry — so that Cat machines would meet Tier 4/EU Stage 5 mandated compliance dates of Jan. 1, 2018 / Jan. 1, 2019, respectively. For Caterpillar, these efforts enabled our mining trucks to provide improved engine component life to help our customers’ total cost of ownership (TCO) and produce a neutral TCO compared to our Tier 2 products,” said Jeff Castleman, new product introduction manager, large mining trucks for Caterpillar."

Aug 1, 2019

To generate a most profitable ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1990

By M. A. Boucher

The purpose of my presentation is threefold: a) to make you aware of what is available in Canada in terms of refractory minerals. b) indicate the mineral deposits that have potential for development. c) show the advantages of Canada as a supplier of electrical energy necessary for the production of electrofused minerals. Canada is a producer of natural refractory minerals, electrofused minerals, and synthetic refractory minerals. Several deposits also have good potential for development. The natural refractory minerals produced in Canada are shown in Table 1. The major minerals by decreasing order of importance in terms of tonnage and values are: dolomite, graphite and magnesite.

Jan 1, 1992

By J. J. Sammarco

Computer-aided control of a mining machine pl aces its operator in a safe, remote location, thus reducing health and safety risks, Sensing systems that provide machine position (xy coordinate) and heading (yaw), are extremely useful in aiding remote positioning of mining machines. The U. S. Bureau of Mines has developed two sensing systems for position and heading information: A scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system that employs ring-laser gyroscopes. This paper presents a brief background and status of these sensing systems as applied to the remote positioning tasks of a continuous mining machine. Included are field test results of each system operating in a room-and-pillar research section at a cooperating mine in West Virginia.

Jan 1, 1992

By T. M. Gurr

In response to concerns voiced by local, state, and federal agencies and various environmental groups, the Central Florida Phosphate Industry and various governmental agencies have been investigating methods to accelerate the consolidation of waste clays generated during phosphate washing and beneficiation processes. The objectives of research efforts have been to reduce the storage volumes required for clay waste, accelerate reclamation and to return the land to approximate pre-mining topography. Government and industry research to accelerate waste clay consolidation has evolved two general methods: gravity thickening and chemical flocculation. Gardinier, Inc. one of the phosphate mining companies, evaluated the use of synthetic (polyacrylamide) flocculants as an alternate waste clay thickening method in response to mining conditions encountered at their Fort Meade Mine and the proposed North Hardee County extension of the Fort Meade mine (Figure 1). After considerable research and evaluation, the Alsthom-Atlantic Clariflux Super-flocculation method was chosen by Gardinier, Inc. as a method to seriously consider for use at their Fort Meade mine.

Jan 1, 1986

By Hemant Agrawal, Arvind Kumar Mishra

Rock breakage using blasting is one of the important operations of the mining industry. The delay timing decides the initiation sequence of holes in the blasts and is a crucial factor to improve the overall blast performance. Blast-induced ground vibration is an undesired yet unavoidable outcome of blasting. Peak particle velocity (PPV) is commonly used to measure the magnitude of blast-induced ground vibration. Channelization and better utilization of explosive energy delay are provided between blast holes using initiating systems. The use of different initiation systems even on the same site results in a very significant difference in the values of PPV generated. Due to scattered delay timings of pyrotechnic detonators, the scaled distance predictor equations obtained become unreliable. The error/scatter in delay timing leads to overlapping of holes and hence increases in maximum charge per delay. In this paper, an analytical approach has been discussed to measure the overlapping of holes during blasting with initiation systems having inherent cap scatter. The analytical approach will be calculating the probable overlapping of holes due to scatter in delay timing and will help blasting engineers to understand the variation in maximum charge per delay due to pyrotechnic based initiating systems. In this study, a total number of 102 blasts were conducted using different initiation systems at two different opencast coal mine and 221 corresponding blast vibrations events were recorded.

Nov 10, 2020

By Lawrence A. Roe

This paper describes research and development efforts leading to a wet process for the beneficiation of Western talc ores in which the values are primarily present as soft, platy talc mineral. The mineralogy of the ore, as it relates to the logic of utilizing an uncomplicated, attrition-scrubbing sedimentation process is described. Bench-scale laboratory testwork and a pilot-plant test program are described. The pilot-plant program included production of several tons of products. The thickened talc slurries were very difficult to dewater prior to the drying step. Dewatering difficulties were overcome by use of a high-speed centrifuge. The centrifuge cake was dried either by tray, flash or spray drying. The successful use of one high-grade talc product as titanium dioxide extender in paper is discussed. The talc product has extremely low abrasion values, an important characteristic for minerals used in paper manufacture. It is concluded that this wet process for soft talc ores is capable of producing high-purity talc products for paint, paper, cosmetics and other industrial uses re-quiring very pure soft talc.

Jan 1, 1972

By M. Manrique

Various pyrometallurgical methods for treating Ilmenite and Zircon concentrates are reviewed. Laboratory experiments, using a thermal plasma reactor, have been performed to evaluate: the conversion of ilmenite to TiC or TiC-Fe and the conversion of zircon to ZrC or ZrC-SiC. Results are examined and possible processing routes are identified.

Jan 1, 1996

By P. C. Kapur

For mineral processing spirals, mathematical force equilibrium models are sought to extend the spiral performance envelop. In Part 1 of this report, a complete geometric description of the helical spiral and its trough or channel contour is provided. The secondary circulatory fluid motion in the transverse direction that develops when water flows down a tightly turning curvilinear path and its implications for gravity separation are discussed. Different forces that act on the particle during its passage through the spiral are enumerated and quantified for a better appreciation of their relative contributions and roles in the separation process. Three force equilibrium models from the hydrology literature on sed iment transport are employed to simulate a typical spiral. While the results are promising in that the models mimic the broad performance characteristics of the spiral, what is needed is a more general spiral model taking explicit cognizance of the missing components essential to the spiral description. These are such components as centrifugal force and the steep tangential slope of the channel deck. Results of this latter exercise are deferred to Part 2.

Jan 1, 1996

By Robin Dill, Wei Song, Andrew Perham, Leo Martin

"AECOM completed a subsurface exploration program for an 18-foot diameter, approximately 4-mile long rock tunnel project in Hartford, CT. The tunnel crosses the regional geologic trend through the middle of a sedimentary basin, passing through four separate rock formations, including two volcanic flows. Faulting is prevalent, with at least 15 faults encountered during the site investigation. Severe artesian flows were also experienced in several of the borings, requiring highly specialized drilling equipment. Sixty-two borings and associated testing were performed to characterize the structural geology, hydrogeology, rock properties and ground conditions. A phased program was carefully planned and implemented with participation of geotechnical and geologic specialists, with thoughtful evaluation along the way to react to the ground conditions encountered, and make appropriate refinements. This paper will discuss the subsurface program details; the integrated efforts used to effectively characterize the ground; and will summarize the final characterization presented in the GBR. PROJECT DESCRIPTION The South Tunnel Conveyance and Storage Tunnel project is part of the Metropolitan District (MDC’s) Long Term Control Plan to address discharges to various water bodies throughout the greater Hartford area. This program includes a main conveyance and storage tunnel; a tunnel boring machine (TBM) launch shaft and retrieval shaft; adit tunnels with associated drop shafts and connection structures; consolidation conduits and manholes; and a tunnel pump station (TPS) at the downstream end of the main conveyance tunnel. AECOM is serving as prime designer for the MDC on this project. The main conveyance tunnel (hereinafter referred to as the “South Tunnel”) will be a deep rock tunnel with an invert depth of approximately 180 feet at its downstream end and approximately 218 feet at the TBM retrieval shaft. The tunnel will have a finished diameter of 18 feet. The tunnel will rise in grade at a slope of 0.1 percent to its upstream end. Total invert depth along the deep tunnel alignment ranges from about 180 ft. to as high as 320 feet. The total length of the tunnel will be 21,754 feet. The South Tunnel will be constructed using a shielded TBM and fully lined with pre-cast concrete segments."

Jan 1, 2016

By V. K. Gupta

The experimental results of some wet batch and continuous grinding experiments carried out in a 40 x 40 cm grate discharge ball mill have been analyzed for the variation of the grinding rate parameters, Si, with various operating conditions using a linearized population balance model. The wet grinding tests were carried out under conditions which were very similar to those encountered in the actual practice in plant operation. Well distributed -4 and -20 mesh feeds of two complex pyritic ores were used. The volume-percent solids in the pulp ranged from 30-40, the particle load from 5-8 kg, and the solids feed rate from 70-1 10 kg/hr.

Jan 1, 1981

By W. P. Barnett

In 1988, the U.S. Department of Energy's Pittsburgh Energy Technology Center identified three coal cleaning options for achieving flexible environmental control strategies aimed at reducing energy-related SO2 emissions. These are selective agglomeration, advanced froth flotation, and advanced cycloning. Each technology relies on maximum liberation of pyrite and other mineral matter through feed coal comminution to fine and ultrafine sizes. Research projects designed to expeditiously develop each of these technologies to the point of commercial viability were initiated. This paper will present the status of these projects and the application potential of each technology to coal beneficiation.

Jan 1, 1992

By H. Kinilakodi

The authors previously developed a methodology that combines injury and citation measures into an overall mine safety performance evaluation tool, called the safe performance index (SPI). It can be easily adopted by mine operators to monitor trends in their injury and citation experiences as a risk assessment method. In this paper, six normalized safety measures and the SPI are used to evaluate the health and safety risk that existed at mines in the two years preceding the occurrence of a fatality. The percentage of mines is given for which the risk was high or where trends of some of the safety measures indicated moderate risk. In 50% of the mines, this mine safety performance tracking method could have been helpful to the companies, state agency or the U.S. Mine Safety and Health Administration (MSHA) in recognizing and addressing emerging problems with actions that may have been able to predict high-risk conditions, the fatality and/or other serious injuries. The approach would have given extra scrutiny to the risk for mines that encompassed 74% of the fatalities during 2007-2010.

Jan 1, 2012

By James Paone

Subsidence movements have damaged houses, schools, streets, and public utility lines in some undermined sections of Belleville and Maryville, Ill. In cooperation with local officials and the State of Illinois, the Interior Department's Bureau of Mines is sharing experience in backfilling abandoned coal mines to demonstrate that bituminous coal mine workings in south-western Illinois can be successfully backfilled and subsidence-prone areas stabilized. Subsurface investigations revealed that mine workings are dry and underlain by underclay deposits susceptible to instability upon wetting. Backfilling will therefore be accomplished by pneumatic injection instead of the hydraulic methods used in previous subsidence-control projects.

Jan 1, 1977

By M. D. Martin

Low metal prices and increasingly stringent environmental regulations, coupled with the threat of higher governmental royalties are adversely affecting both existing and new operations. Existing operations must therefore be run at maximum operating efficiencies to enable mining companies to survive and grow. Well planned and executed "outsider" reviews can help achieve this goal. Many mine managers and those who direct them resist the idea of "outsider" reviews for a variety of reasons, some valid and some not. Those managers who do bring in the "outsiders" are nearly unanimous in reporting that the exercise in self-discipline was well worth the pain and effort and repaid the cost many times over. This paper makes a strong case for "outsider" reviews and gives recommendations on the kinds of reviews to undertake. The authors draw upon their nearly 70 years combined experience, much of which has been in operations.

Jan 1, 1994

By Manoj Khandelwal, Jian Zhou, Yingui Qiu, Peixi Yang, Pingan Peng

Rockburst prediction is crucial in deep hard rock mines and tunnels to make safer working conditions. Due to the complex interaction of many factors involved in rockburst prediction, such as multi-variable and multi-interference factors, three hybrid support vector machine (SVM) models optimized by particle swarm optimization (PSO), Harris hawk optimization (HHO), and moth flame optimization (MFO) are proposed to predict rockburst hazard level (RHL). The RHL is determined according to four kinds of microseismic characteristic parameters including angular frequency ratio, total energy, apparent stress, and convexity radius. Then, six types of microseismic characteristic parameters are taken as input variables in 343 sets of data, including angular frequency ratio and total energy, etc.. And the RHL is taken as the output target of rockburst prediction. The classification performance of PSO-SVM, HHO-SVM, and MFO-SVM hybrid models is evaluated by accuracy (ACC), precision (PRE), and kappa coefficient. Findings reveal that the MFO-SVM model performs best in terms of accuracy, with ACC, PRE, and kappa coefficients reaching 0.9559, 0.9063, and 0.9094 respectively, while PSO-SVM and HHO-SVM have similar performances. However, the PSO-SVM, HHO-SVM, and MFO-SVM all perform better than the unoptimized SVM model. This confirms that the three optimization algorithms significantly enhance the rockburst prediction capacity of the SVM model to help mine practitioners apply machine learning methods to rockburst prediction problems appropriately.

Feb 3, 2023

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By BHAMIDIPATI S. SASTRY, ANMAYA NAIK, ASIF AHMAD, Srivatsan Jayaraman Sridharan, ADITYA PANDEY

Wet kata cooling power (WKCP) as measured by a kata thermometer is a well-known heat stress index used in the mining industry. Although, over the years, several researchers proposed different heat indices and indicated limitations of the kata thermometer, WKCP is used in the South African gold mining industry due to its simplicity and rapidity of assessment. This paper presents a comparative analysis of the newly developed empirical expression for the WKCP and some of the more commonly used empirical models. For this purpose, WKCP measurements are obtained based on experiments conducted in a low-speed wind tunnel. Based on a regression technique, the analysis presented aims to assess the disagreement between the empirical model predictions and actual measurements. The correlation is also presented between WKCP and the well-established thermoregulation models using parameters from the low-speed wind tunnel experiments, including dry-bulb temperature (Td), wet-bulb temperature (Tw), barometric pressure (P), and wind speed (v). It is found that the proposed empirical model for the WKCP represents the bioclimatic interaction quite well under the specific parameters that defines the harsh thermal environment and air condition, such as metabolic activity, clothing of the person, and the velocity of the ventilating air in which the person is working. The statistical analyses performed show that the empirical model proposed for the WKCP produces satisfactory estimates of the thermal stress experienced under lower air velocities, light clothing, and higher metabolic activity rates.

Sep 2, 2021