Search Documents

By Brendan Donnelly, Jung-Hoon Sul, Lasitha Piyathilaka, Sanghyun Jeong, Benjamin Probyn

The chains of armored face conveyor (AFCs) are constantly in contact with water and wet coal, which results in a significant proportion of unplanned downtime experienced on longwall equipment due to corrosion. While reverse osmosis (RO) is one of the most prevalent water treatment methods for reducing salinity and dissolved solids in coal mining, its impact on the corrosion of the AFC chains has not been well studied. This work studies the direct effects of RO water on the corrosion of AFC chains. Immersion tests followed by surface micromorphology analysis and corrosion indices indicate that the RO water increased the corrosion rate of the AFC chains due to the reduced tendency of preventive films on the chains.

May 1, 2024

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By T. T. Toomver

The evolution of Inco's Selective Reduction Smelting Process as practised today is described, beginning with the initial laboratory experiments on small samples to the processing of large bulk samples through pilot plant equipment. For both the Guatemalan and Indonesian (Soroako) ores, the initial screening tests using hydro-, vapo-, and pyro-metallurgical processes showed that the latter was the most promising both metallurgically and economically. Later, larger scale tests confirmed the earlier testwork.

Jan 1, 1979

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By H. R. Hernandez-Guerrero, S. A. Robles-Salazar, M. Marín-Pasillas, P. J. Pompilla-Rosales

Peña Colorada is a company dedicated to the exploration, exploitation, and beneficiation of iron ore, serving the national steel industry. Established in 1975 as a stateowned enterprise, it transitioned to operating as a private organization in 1991. It is jointly owned by two investors, ArcelorMittal and Ternium, each holding a 50% stake. The mining operation is situated in the municipality of Minatitlan, in the northwestern part of the state of Colima, Mexico (Figure 1). It comprises an open pit mine and a concentrator, covering an area of approximately 2,300 hectares. The pellet mill is in the town of Manzanillo, Colima state, a port on the Pacific coast, about 46 km southwest of the mine. The pellet mill occupies its own property with a total area of 60.4 hectares. A gravity-driven concentrated slurry pipeline connects the mine and the pelletizing plant, located at an average elevation of 1,020 meters above sea level and 20 meters above sea level, respectively. Currently, Peña Colorada produces 4.1 million tons of pellets and 0.4 million tons of iron concentrate annually. In 2018, due to a change in the cutoff grade, the processing volume of the beneficiation plant increased from 9 million tons to 16 million tons annually. This led to a greater amount of information to process and characterize the ore extracted from the pit before its processing in the beneficiation plant. Consequently, Peña Colorada sought new ore control technologies to enhance ore selection, optimize human resources and data management, as well as minimize discrepancies between planning and execution. To ensure adherence to quality agreements with stakeholders, it is crucial to understand the ore characteristics before initiating mining activities.

Feb 1, 2024

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020

By L. G. Wilson

In order to comply with time limitations imposed by this symposium, a very narrow but nonetheless interesting segment of the market has been chosen for discussion of the preparation of a tailor-made product to meet a specific need, and in view of the fact that the barite market is one of the oldest and one of the broadest non-metallic mineral markets in the world, it is necessary that we place this in perspective. Of a recent world annual production; (i.e., 1966 figures released last year in MINERALS YEARBOOK), of some four million tons, the United States consumed over 1/2 million tons, of which approximately 950,000 tons were produced domestically and approximately 700,000 tons were imported. Of this total, something approaching 90% was used for drilling-mud weighting, and of the balance, all but about 60,000 tone is consumed in the production of glass, barium chemicals, aggregates, and other minor uses; thus we are really taking a look at a very minute, however important, and very selective, portion of the total barite-market. The real meat of this paper, after eliminating all irrelevant uses of barite, and delineating the area of discussion, resolves itself into the approach to a favorable marketing area and a specific attack on that area. Cost, to the user, has been, patently, a function of distance, as the basic price of barite has varied very little over the years until recently, and freight rates have been the governing factor. Conversely, the seller of barytes must make concession in the plant price to compensate for distance, if he is to successfully compete.

Jan 1, 1969

The mining industry is one of the three pillars of the Namibian economic development, besides tourism and the fishing industry. Generating 20 % of the GDP and more than 50 % of the export income, half of this amount derives from the diamond mining industry. In 2008, the annual production of 2.2 mio carat achieved an income higher than 1.44 billion Namibian Dollars (more than 750 mio Euro). After the global recession in early 2009, which also caused a significant downcrease in production to only 0.93 mio Carat, the diamond mining industry easily restored itself and the production figures for 2010 are expected to be even higher than those achieved in 2008. Compared to other diamond producing countries, Namibia is mainly producing diamonds of highest quality (jewellery quality), with less than 10 % of the mined diamonds not falling into this category. This high quality stands also for the worldwide highest prize achieved per carat. With 370 $US per carat it is more than four times higher than that of the average South African stone. In 1908 the finding of the first diamonds in the Namib desert close to the coastal town of Lüderitz was reported by a Mr Stauch, railway inspector for the then German colonial railway company. This event immediately triggered a Diamond Rush and subsequently the set-up of the restricted diamond mining area ?Sperrgebiet? through the German colonial administration. In 1913, only five years after the first mining operations had started, the steadily increasing production allowed for more than 20 % of the diamond production worldwide. After the First World War, the new South African government concentrated all mining activities in one organization, CDM (Consolidated Diamond Mines of South West Africa) which in following decades conducted an extensive and detailed exploration of the whole Sperrgebiet and started numerous new diamond mining operations.

Jan 1, 2011

In this study, numerical simulations of yield pillars employing the finite element method with time-dependent Drucker-Prager material model are conducted. The stress control mechanism of yield pillars on weak floor strata is studied. The development of pillar yield zone, the distribution of pillar stress and the development of failure zone in the weak floor strata are investigated. The study indicates that a properly selected yield pillar size may significantly reduce the peak stress induced in the weak floor strata and effectively control the development of failure zone in the floor.

Jan 1, 1999

By J. P. McCluskey

The effects of air quality regulations passed in the last few years have been felt in a more pervasive way by the electric utility industry than by perhaps any other industry. I'm referring especially to those regulations dealing with the control of air emissions from stationary sources, and those specifying the quality of fuel used. Particularly, I would like to describe some of the effects that these regulations have had on the Commonwealth Edison Company. To put the subject into perspective, a brief descrip¬tion of the company will be presented first. Then, a historical outline of some of the efforts at control of electric generating station emissions will be described. Following this will be an indication of the Company's response to early State and local regulations prompted by the growing pressure for stringent envi¬ronmental control. Finally, the Company's plans to achieve com¬pliance with the most recent, Federally approved, State of Illinois regulations will be summarized.

Jan 1, 1973

By M. Javier

"The impact of mine closure is perceived through a veil of compliance to human laws and regulations rather than the laws and equilibrium of nature. This perception motivates present research. Understanding the causes and effects of mine closure defines levels of responsibility. This understanding evolves from mine closure's legacy. Mine closure is characterized in perpetuity by three aspects: Future liabilities; level of technologies for extraction and, usage of mineral resources. These aspects must be updated to a rationally appropriate level. This paper will address the following questions: Will the minerals remaining in the process of mine closure ever be recovered? Will the mine closure inhibit the availability of minerals for the next generation? How many mines are designed to perform a successful mine closure? Do we close the mines or do we close nature? Is it responsible to continue mine closures as we do them today? Is mine closure a complement of mine operations or a contradiction of mining? Do we need to perform mine closures, yet? This paper reviews mine closure practices and principles with the level of responsibility to nature and for the next generation.PREFACE The planet has irreversible issues to deal with regarding the depletion of mineral resources and contamination occurring from human activities. The population increased exponentially to more than seven billion, this high population with its lifestyles, demands a higher supply of minerals. In spite of these conditions, mining is a vital industry to keep ""civilization"" in society. This is evidenced by what we see around us, in that everything ""made"" in society is directly or indirectly due to mining. Hence, mining cannot be avoided or ignored. Society misunderstands the importance of mining in relation to other activities. At this time, mining is fragmented and economically oriented to supply cheap minerals to a market with peculiar characteristics regarding products that could be designed for recycling and stimulate nature’s equilibrium. These issues add important “variable factors” to the equation, when they are considered as parameters for the next generation. It also raises many questions regarding principles and attitudes about morals and ethics exercised in all anthropogenic activities. The industry's practices have many flourishing paradigms which are subject to a variety of criticisms and observations. Some of these observations will be described in this paper. It is important to clarify in advance a ""normal disclaimer"" about the ""apparent contradiction"" that could take place in the writer's comprehension when we abruptly ""jump to conclusions"". We must remember that we are profiling the future in an arena that demands a better understanding of solutions to problems created by actual mining."

Jan 1, 2015

By M. Jaramillo

The Expanded West Pit of the 15 MTY El Cerrejon Mine will reach a maximum depth of270 m. Slope stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization call for anchoring the footwall by installation of cable bolts, 9 to 33 m long, of multi-strand steel cable. For each of the 15 m high mining benches, a row of bolts is installed with variable horizontal spacing, depending on dip magnitude. Cable bolting is now standard operating practice and 11800 bolts will have been installed during the life of the mine.

Jan 1, 1995

By M. Bai

The influence of mining on the hydro-geomechanical environment is greatly constrained by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of geometry changes, can be reasonably predicted through a coupled finite-element model introduced in this paper. Verification of the model has been tested using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1993

By T. Braun

A greenfield open pit gold mine in Latin America suspended operations less than three years into an eight-year mine plan after a waste rock dump and heap leach facility sustained substantial damage from a deep-seated landslide. No injuries to employees were recorded because of the slow-moving failure. Due to early detection by the operations team, the owner had sufficient notice of the potential failure and successfully rinsed the heap leach facility prior to the failure event. Engineers estimated approximately 35 million cubic meters of mass movement below the waste rock and heap leach facilities. The original eight-year mine plan produced approximately 60,000 ounces of gold per year. After the failure, the owner terminated gold production, re-configured the mine site to a safe, standby condition and launched a detailed investigation into the root-cause of the failure. Approximately two years after the shutdown, legal interests filed a statement of claim and named three engineering design firms and individuals involved in the project. Several years of litigation, including discovery and deposition proceedings, followed as the legal process considered evidence spanning a 20-year timeline. Changes in project ownership and consulting firms during the development and operations phase complicated the process. In 2017, the plaintiff and last defendant settled. The author was involved as the corporate representative for one of the engineering design firms.

Mar 2, 2022

By James R. Jones

The purpose of these opening remarks is to establish a viewpoint, which will form part of the basis for later discussion between panel members and between the panel and the audience. Important issues will be identified. These ideas in the form of questions and answers, hopefully, will provide the necessary background for the ensuing dialogue. Is There An Urgency? We do not believe there is the urgency for immediate control legislation that has been depicted by some Congressional sources, environmental groups, and certain segments of the press. Emissions of sulfur oxides in the United States have decreased 15% during the 19701s, even though the use of coal by electrical utility power plants increased nearly 80%. That trend will continue as the older plants are phased out of operation and are replaced with newer plants, which must meet the New Source Performance Standards (NSPS) requiring the use of "scrubbers" to reduce sulfur dioxide emissions by 70% or 90%. The present Clean Air Act Amendments of 1977, by allowing the logical progression of economic events- -depreciation, retirement, replacement, and growth--will produce approximately a 50 % reduction in SOX emissions by the year 2015.

Jan 1, 1984

By R. Merkl

Since the 1940s, decanter centrifuges have become more important for increasingly complex solid-liquid or solid-liquid-liquid separation processes. Sometimes processed industrial or metalliferous minerals are abrasive or are treated with corrosive chemical agents. Traditional mining applications include the processing of coal, gravel and other products, where low-speed decanters, as well as screen bowl decanters and filters, dominate. These have been increasingly replaced by high-speed decanters during the last decade. Decanter centrifuges also started to play a key role in applications such as drilling muds, processing carbonates and separating SX crud in copper platinum ore concentrations of nickel and gold. Communication between machine producers and mineral processing engineers is vital for the right choice of materials and the design of the right decanter centrifuge for the individual process.

Feb 1, 2012

By M. R. Shahan, W. R. Reed

A laboratory apparatus (shield dust simulator) was designed and constructed to simulate the dust generated during the advance of longwall hydraulic roof supports, or shields. The objective of the study was to develop a tool that could be used to test the hypothesis that foam applied to a mine roof prior to a shield advance could be used to reduce the respirable dust generated during shield advances. This paper will outline the design parameters for the development of the system, as well as describe baseline testing of coal and limestone dust. Results show the average instantaneous respirable dust concentrations that occurred during simulated shield advance. Confidence intervals were calculated from the instantaneous respirable dust data to determine the repeatability of the data produced by the device. INTRODUCTION During longwall mining, miners can be exposed to respirable dust that is generated during the advance of hydraulic roof supports or shields. National Institute for Occupational Safety and Health (NIOSH) researchers have conducted numerous surveys of longwall mining operations, benchmarking the operating practices and dust control measures in use. It has been determined that the shields are responsible for 27% of the respirable dust that is generated on the longwall face [1]. The dust generated by the shield advances ranks second, next to the longwall shearer which is accountable for 43% of the respirable dust generated on the longwall face. The respirable dust generated during the advance of the shields can be a significant contributor to the respirable dust exposure of the mining personnel operating at the longwall face, especially since some of this dust is generated in the walkway. Control systems designed to reduce the dust levels generated during the shield advance have the potential to greatly reduce the respirable dust exposures of the personnel downwind of these activities. One control technology to decrease the dust generated by the shield advances would be to apply a layer of foam to the forward shield-roof interface prior to the shield advance [2]. The blanketed layer of foam would interact with the material located on the top of the shield during the advance, preventing a portion of that dust from becoming entrained in the mine air. This layer of foam would be applied using a foaming nozzle located on the longwall shearer body that would spray foam on the roof surface as the shearer passed. Substantial laboratory work has been completed to determine the feasibility of this type of foam application. NIOSH engineers have classified the various characteristics of foaming agents, using foam expansion ratio and drainage as important properties, as well as developed the mechanical systems required to apply the foam safely to the mine roof [2, 3]. The construction of an apparatus that could simulate the mechanical interaction between the dust-laden shield top and mine roof was necessary to adequately test the hypothesis that foam could be an appropriate control. A team of engineers designed and constructed a shield dust simulator system allowing for in-house testing prior to a full-scale field investigation.

Jan 1, 2019

By R. E. Thill

An ultrasonic, pulse-immersion apparatus and method are described for determining the effects of moisture on the dynamic elastic properties of rock. The method provides an alternative approach for assessing the moisture sensitivity of rocks. Ultrasonic wave velocities are continuously monitored in immersed rock samples as a function of water absorption and time up to saturation. Moisture effects on compressional wave velocity vary as a function of the type of rock and the time and amount of water absorption. Regression analyses are used to curve-fit plots of the data and to derive empirical expressions for compressional wave velocity as a function of water content for different categories of rock. Results indicate that compressional wave velocity can be used to predict both the moisture content and its effect on strength and deformational properties of rock. These results have potential for detecting or monitoring bad roof conditions in situations where the mine rock exhibits strength degradation with moisture absorption.

Jan 1, 1986

By A. P. Grobbelaar

Andalusite is a member of the sillimanite group of minerals consisting of andalusite, kyanite, and sillimanite. These minerals are the structural polymorphs of Al,Si05 (the anhydrous silicate of aluminium) and although chemically similar, they differ in physical properties due to their different crystal structures. For further information on the sillimanite group, see the chapter on Kyanite and Related Minerals that follows. The minerals are generally the products of the metamorphism of alumina-rich sediments and are found in schists, gneisses, or hornfelses, which have undergone either regional or thermal metamorphism from their original form. Sedimentary deposits may also form since the minerals are chemically and physically resistant to breakdown. When heated to a sufficiently high temperature the sillimanite group minerals convert to mullite with a resultant volume expansion and the liberation of silica. Due to the stability of the mullite formed, its high hot strength and resistance to chemical and physical erosion, they are widely used in the manufacture of refractories and special ceramics (Table 1). The reaction can be represented as follows: [ ] The worldwide use of these minerals depends to a large degree on their availability (Fig. 1). Andalusite, with its lower conversion temperature and the lowest volume expansion on being heated is the natural choice as a raw material to produce energy-saving refractories without prior calcination. The Republic of South Africa holds by far the largest minable andalusite deposits of the world, estimated at some 70 Mt of known in situ reserves. The only other large commercial production of andalusite comes from France, with known reserves of about 5 Mt. Potential new deposits are known from China, Ireland, Australia, and South America. World consumption of andalusite in special performance refractories has risen from less than 10 ktpy in 1960 to nearly 300 ktpy in 1990, which is due to cost effectiveness in many industrial applications compared to other conventional refractory products. Andalusite-based refractories have traditionally been used in Europe, South Africa, and the Far East; usage in America was limited in the past due to relatively high delivery costs and availability of other local refractory minerals. However, there is a significant trend towards greater use of andalusite in North America, thus opening new markets and replacing other traditional refractory raw materials. GEOLOGY Andalusite occurs in metamorphosed rocks of clay-like com- position, as in the andalusite-hornfelses in thermal aureoles (contact metamorphism), formed under conditions of high temperatures and low stress, and in regional metamorphic rocks, such as the andalusite-schists. These schists are mostly unconnected with definite igneous intrusions but were presumably also formed at high temperatures and under low stress. Andalusite can also appear in alluvial deposits associated with the primary deposits. At depths of 10 to 20 km, temperatures of up to 450°C might be expected. Another result of increasing depth is an increase of pressure due to the load of the rock cover. The load stresses involved in metamorphism is generally believed to lie in the range 0 to 10 000 bars. During contact metamorphism the increase in temperature is brought about by the injection of magma. The temperature reached in the country rock at some distance from the igneous body will always be less than the initial temperature of the intrusion, which is presumably less than 1 200°C, and will vary with time and distance from the contact. A simple metamorphic reaction involving dehydration of an aluminous sediment can be: [ ] At higher temperatures sillimanite would form at the expense of andalusite, while kyanite would be the mineral formed at higher pressures, as can be seen in the phase diagram of A12Si05 (Fig. 2).

Jan 1, 1994

By Donald J. Donahue

Ladies and Gentlemen: As we begin these three crowded days of technical and economic discussion of problems faced by mining and metallurgical engineers, it seems appropriate at this Keynote Session to consider the future of this industry from which we derive our livelihood, It is also appropriate at this international meeting to view our industry on a world-wide basis. First, let us assess the world's future needs for minerals - the needs which it is our industry's task to meet. Next, let us look at what supplies of minerals may be available to meet those needs. I will speak of this first in terms of the physical availabilities of minerals. Finally, we can consider some of the social or institutional factors which will condition the world's mining industry as it goes about its task of discovering, developing, producing, and delivering the minerals needed to meet the world's demands. Let me give you a foretaste of my conclusions. First, future world demands upon our industry will be enormous, eclipsing anything that we have known up to this point. Second, there is strong evidence that our earth's crust contains a sufficient physical quantity and variety of minerals to meet forthcoming needs for as long a period ahead as one can envisage.

Jan 1, 1974