Search Documents

By Robert D. Coale

This paper will describe the copper concentrate slurry pipeline and pumping system between the concentrator and the port at Bougainville Copper Ltd. The operations of Bougainville Copper Ltd. are located on the island of Bougainville in the South Pacific. Geographically, it is the northernmost island of the Solomon Group but, politically, it is part of Papua New Guinea. Papua New Guinea is a United Nations Trust territory administered by Australia, having recently been given self-government, with independence scheduled for December 1974. (Fig. 1). The island is approximately 130 miles long by 30 miles wide, with the Crown Prince mountain range forming a spine along its length. The mountains in place are over 8,000 feet high with the mine located on the western flank at an elevation of 2,200 feet. Exploration on Bougainville for copper by Conzinc Riotinto of Australia (CRA) began in 1963 and by 1968, through geophysical, geochemical and diamond drilling methods, an orebody containing nearly one billion tons of ore grading approximately 0.48% Cu. and sane gold had been outlined. Bougainville Copper Ltd., the company operating the mine, is 53.6% wined by CRA, 20% mined by the government of Papua New Guinea with the public Folding the remainder of the shares. The first copper concentrate was produced in early 1972, with production for the first full year, 1973 being:

Jan 1, 1974

By Shaojun Bai

Siderite ore with high phosphorus content was reduced isothermally at 1,050° C with pulverized coal and different dosages of sodium carbonate. X-ray diffraction (XRD), scanning electron microscopy (SEM) and energydispersive analysis of X-rays (EDAX) were used to characterize the samples. The influence of sodium carbonate on the carbothermic reduction process was investigated. Sodium carbonate and its dosage played a considerable role in the carbothermic reduction. The iron particle size in the reduced ore was below 20 µm, and fayalite was abundant without sodium carbonate additive. With a mass ratio of Na2CO3-to-ore of 5% additive, the iron particle size in the reduced ore was generally above 50 µm, and the diffraction intensity associated with metallic iron in the XRD pattern increased. The effect of sodium carbonate on the phase transformation of fluorapatite during carbothermic reduction was also addressed via thermodynamic calculations and aqueous leaching experiments. The results showed that the fluorapatite was not reduced to P2 at 1,050° C, and a portion of the fluorapatite was converted to soluble phosphate. The reduction of siderite can be catalyzed by adding an appropriate amount of sodium carbonate. This catalytic activity was caused by an increase in the reducing reaction activity of FeO and the acceleration of the carbon gasification reactions. The decrease in phosphorous content in the iron concentrate was attributed to an improvement in the separation of the iron phase from the slag phase when sodium carbonate was added and with the formation of soluble phosphate.

By G. R. Doubek

Dual Tube Reverse Circulation (DTRC) drilling has been extensively used for collecting groundwater information for the dewatering program at Amax Gold Inc. Sleeper Mine. This paper presents a discuss ion of the types of data which can be collected from DTRC drilling, as well as the effect submergence has on the data. A simple low-cost method of injection testing has been developed using DTRC equipment, allowing quantitative data to be obtained from exploration or test holes. Potential yields can be determined for each drill location, allowing siting and design of production wells to be optimized.

Jan 1, 1992

By Ulrich O. Lange

Coal is America's most abundant energy resource. Therefore, it IS logical to assume that coal must be produced in much greater quantifies in order to make the United States self-sufficient, as far as energy is concerned by 1985. However, there are a number of obstacles which have to be overcome in order to achieve such a great task. According to one of the most outspoken American Mining men, there are three major obstacles. Those are: (1 ) Mining technology (2) Public image of the coal mining industry (3) Governmental policy toward the mining industry The following will be dealing with Shortwall Mining, which is a very specific part of mining technology and which might influence the image of the coal mining industry as well as the governmental guidelines, at least to make it easier to live with those guidelines. During recent years the operation of coal mines has been more expensive than ever. Since 1970, the cost of producing coal increased by 30% and the productivity dropped by just about the same amount. Those are alarming signs.

Jan 1, 1975

By I. Anazia

Selective fatty acid flotation of carbonate gangue from sedimentary apatites was achieved under acidic pH's without a specific apatite depressant and without conditioning the pulp with the collector. Concentrates (35-38% P205, 0.8-1% MgO) with high recoveries (80-85%) were produced from Indian and Chinese dolomitic ores. The calcareous and/or dolomitic-siliceous phosphate ores of South Florida and Utah required two flotation stages: one for carbonate removal, as mentioned above, and the other for phosphate recovery from siliceous gangue. Preliminary tests on the South Florida ore gave concentrates analyzing 29% P205 and 0.8% MgO with a P205 recovery of 76%. Data are also included showing the applicability of the process to the dolomitic-calcareous-siliceous Western U.S. phosphate ore from Utah. A concentrate obtained from this ore assayed 30% P205 and about 1% MaO.

Jan 1, 1987

By Rodolfo Lagos, Nicos Pfeiffer, Ben Harding, Clayton V. Deutsch

This paper documents a probabilistic resource modeling workflow for the Round Mountain epithermal gold deposit. The set of categorical and continuous variable simulated realizations provides a model of variability and uncertainty given the current orebody knowledge. These realizations can be used to quantify and understand expected deviations in reconciliation during mining and provide a more accurate measure of expected gold than an estimated model. Gold mineralization at Round Mountain is primarily contained within tertiary tuff units, which dip gently to the west and thicken towards the southern part of the orebody. Domain boundaries are modeled as combinations of lithology and alteration; alteration domains are constrained to be within the tuffs. Large-scale geologic uncertainty is strongly influenced by parameter uncertainty, particularly the input histogram. The spatial bootstrap characterizes prior global uncertainty in the input histogram for categorical and continuous variables. Categorical models are generated using hierarchical truncated pluri-Gaussian (HTPG) simulation. Continuous variable simulation is carried out within the simulated domain boundaries using trend models to account for non-stationarity.

Aug 19, 2023

By R. E. Hamilton

It is more than ten years since the first fully automated process using a computer started operation. Computer control has become common in a number of process industries, yet in spite of the tremendous incentives which ere present, there are only a few computer installations in the mining industry and none of these has announced successful control of a process. Recognizing that one of the reasons for this slow progress is the lack of adequate mathematical models of the various processes involved, the author's company started a project in the summer of 1966 to develop such models. It was early recognized that the existence of a major disturbance input, in the form of the mineral composition of the feed prevents most flotation plants from attaining a steady state condition. This makes the custom¬ary method of developing correlations from steady state plant data inapplicable and requires a more fundamental approach.

Jan 1, 1968

By Kostas Fytas, Pierre Bousquet, Bill Evanelou

Acid mine drainage (AMD) is a serious environmental problem that preoccupies the Canadian Mining Industry. Considerable amounts of money are spent every year in an effort to prevent or reduce the acid mine drainage phenomenon. AMD occurs when sulphide minerals (ex. pyrite) contained in rock are exposed to air and water and subsequently oxidise to produce low pH water. This acid effluent has the potential to mobilise any heavy metals contained in the rock. Coating the sulphide minerals with silicates is a new promising technology to reduce AMD. Pynte is treated with a solution containing H2O2, sodium silicate and a buffering agent. H2O2 oxidises a small part of pyrite producing ferric iron (Fe3+) ions. These ions subsequently react with the silicate ions to produce ferric hydroxide-silica that precipitates on the pyrite surface producing a passive coating. This silicate coating can protect the grains of pyrite from oxidation. This paper presents a series of experiments that confirm that silicate coating can considerably reduce AMD.

Jan 1, 2000

By John H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the range pH 8-11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction which may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as was observed with the Wyoming bentonite. The results indicate the conditions that should be met with respect to pH control in order to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1983

By Cody Giroux, Homer Scurlock, Michel Wasag

Silica and Crystalline Quartz exposure continues to be a serious health threat to nearly 2 million workers in the United States, including more than 100,000 working in high risk jobs such as abrasive blasting, foundry work, stonecutting, rock drilling, quarry work, mining and tunneling. The primary focus of this study is to identify the best methodology to reduce particulate-laden air and limit/eliminate exposure to respirable dust with silica/crystalline quartz during tunneling operations. This study focuses on two de-dusting systems employed on similar tunnel construction projects. The first project is the Coxwell Bypass Tunnel located in Toronto, Ontario Canada. The second project is the Westerly Storage Tunnel located in Cleveland, Ohio. The Toronto project is utilizing a wet de-dusting system. The Cleveland project is using a dry de-dusting system. The objective is to determine which system provides the best protection and suitability to capture, remove and ultimately reduce respirable concentrations of silica/ crystalline quartz to safety and healthy levels in underground tunneling activities.

Jun 13, 2021

By Joseph W. Murray

GENERAL DESCRIPTION The undercut-and-fill method of mining was devel¬oped by Inco Ltd. in the Sudbury district of Ontario, Canada, to deal with abnormal ground conditions en¬countered in pillar recovery. Although it is now some¬times utilized as a primary stoping method, the main application continues to be in pillar recovery. In any mining method in which fill is employed, pillar systems tend to fail gradually as stoping pro¬gresses. As a result, most pillars are completely destressed and broken by the time pillar recovery com¬mences. Control of the back in such ground becomes a major problem and is contingent on local conditions as they exist in the workplace. In most mining methods, operations such as drilling, blasting, slushing, and tim¬bering can be readily assessed and the mining cycle pre¬dicted. However, in the mining of pillars with overhand methods, the time and effort required to maintain a safe back varies to a quite unpredictable extent. For years the square-set method was the most effective means available for pillar recovery. However, in areas where bad ground was encountered, square setting was a costly and sometimes hazardous method. As the tonnage mined from pillars increased, it was apparent that a safer and less expensive approach was required. Past experience indicated that the best way to deal with broken ground was to mine from the top down. Top slicing systems were examined but were rejected due to the major sub¬sidence which resulted. However, ideas generated from studying top slicing finally developed into the present method of undercut-and-fill. This method, which has almost completely replaced square-set mining, exhibits reduced costs, has improved safety and efficiency, elimi¬nates the factor of bad ground overhead, and allows a closer prediction of the actual mining cycle. The result is more accurate scheduling of pillar production. This factor is of increasing importance as the tonnage from pillar recovery increases in relation to total mine pro¬duction. Undercut-and-fill is a method of extracting a block of ore by mining successive cuts, working from the top down. After a cut of ore is completely mined out, lami¬nated timber stringers are constructed along the sides for the full length of the cut. Round logs covered by a wire screen are laid across the stringers to form a mat. The cut is then tightly filled with hydraulically placed cemented sand fill. Mining is then resumed on the cut immediately below the mat. As the cut advances, the timber stringers are supported by round timber posts seated on the solid bottom of the cut. Drilling, blasting, muck removal, and timbering operations are repeated until all the ore in the cut has been removed. At this time, another log mat is laid and the cut is filled. This sequence is continued until the block has been mined from level to level. The basic principles of undercut-and-fill can be adapted to a variety of mining situations. It can be applied transversely or longitudinally in ore bodies of varying width, that dip from vertical to flat lying. The method can be applied using conventional equipment or it can be mechanized through the introduction of small diesel or air-powered units for muck removal. Undercut¬and-fill is a selective method, ore recovery is high, and dilution can be controlled to an acceptable level. How¬ever, it is a high-cost, labor-intensive method and as such its use is restricted to areas where the less costly meth¬ods of ground support are not successful or where bulk mining methods are not adaptable. One basic require¬ment for undercut-and-fill is an adequate source of hydraulically placed cemented sand fill and a dependable sand plant and distribution system. The success of the undercut method is to a large degree dependent on the competence of the fill placed in each of the successive cuts. In theory, the weight of the fill on each cut is supported in part by the cemented sand itself as it binds to the rough sides of the mined¬out areas next to the pillar walls, and in part by the tim¬ber support. As mining progresses beneath the mat, a downward pressure is exerted within the cemented fill and a voussoir arch develops above the mat, across the full width of the cut. This supports the major portion of the load. The log mat and posts have a double func¬tion in that they carry the remaining weight not sup¬ported by the voussoir arch and in addition prevent any pronounced settling of the fill mass. Excessive settling breaks the bond between the cemented fill and the pillar walls, eliminating the arch effect and transferring the entire load to the mat and posts. The theory of a voussoir arch forming within the cemented sand fill mass is substantiated in practice by the fact that pillars have been mined from level to level with no more significant weight on the bottom cuts than was experienced on the top cuts. In effect, as mining progresses downward, there is no additional transfer of weight from previous cuts to the cut being mined. APPLICATION OF UNDERCUT-AND-FILL Because of their size, the Sudbury ore bodies are, for the most part, mined transversely and, to a considerable extent, by filling methods. Transverse stoping blocks are designed with 9-m (30-ft) crown pillars established be¬low each level and with stopes separated by vertical rib pillars. In past years, floor pillars were left above the level as well, but present practice favors the silling of primary stopes at the base of the rail. Rib pillars are designed to meet the ground control requirements of the primary stoping methods. Local conditions and past experience generally dictate their size. Historically, since the square-set method was to be used for recovery, rib pillars were designed to accommo¬date standard 1.7-m (5'h-ft) sets. A typical rib pillar is four sets wide [6.7 m (22 ft)] when located between two square-set or cut-and-fill stopes having a width of 8.4 m (27.5 ft). When the undercut-and-fill method was de¬veloped, a mat width of two sets was adopted. This di¬vided each cut of the common four-set pillar into two

Jan 1, 1982

By H. Sahay

The current Canadian coal production is approximately 57x106 tonnes per annum of which some 25 million tonnes is exported. Two thirds of the Canadian output is classified as thermal and one third as coking or metallurgical coal. The Canadian coal industry, like the industries in some other industrialized nations, has gone through a cycle of ups and downs. The current world vide recession and stable oil prices have somewhat dampened the plans for a further growth of this industry - albeit temporarily. No new mines are expected to be developed within the next few years. However the production is projected to increase to 60x106 tonnes in 1985 increasing to an estimated 75 to 80x106 tonnes by 1995. The Canadian mines are highly mechanized and are willing to employ the modern technology to maintain its competitive position in the world's coal market. This paper reviews the recent technical developments which continue to improve resource recovery and productivity.

Jan 1, 1986

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Respirable crystalline silica (RCS) found in dust generated by various mining processes is an important occupational hazard in the underground coal-mining industry. Exposure can lead to disabling and incurable diseases, including coal workers’ pneumoconiosis (CWP), silicosis and lung cancer [1,2]. Clusters of rapidly progressive CWP have been observed in the Appalachian regions of eastern Kentucky and southwestern Virginia, and recent cases have been generally more severe and showing more rapid progression. CWP is approximately four times as common among long-tenured underground coal miners in central Appalachia than long-tenured underground miners in the rest of the United States, and 20.6 percent of long-tenured underground miners in central Appalachia were suffering from the disease as of 2017.

By Dr. Jack M. Gillette

A system of models which simulate surface coal mining operations has been developed for use in mine planning and economic evaluations. Micromodels simulate individual mine operations for equipment selection and mine planning. Macromodels simulate all operations in the complete mine for economic evaluation of reserves. A cash flow analysis model makes a complete discounted cash flow analysis to deter-mine a required coal sales price or return on investment for evaluation of any mining project.

Jan 1, 1978

By George A. Snyder

The presence of moderate to high concentrations of colloidal clays in coal preparation plant waters can cause serious operating and economic problems for a coal company. Among the host of possible problems are the following: 1) Poor separation of clays in the plant thickener, resulting in: a) Increased ash in the clean coal. b) Increased specific gravity of the wash water and decreased coal recoveries at the desired quality. c) Increased thickener operating costs in trying to overcome the problem. 2) Decreased solid concentrations in the thickener underflow and increased pumping requirements to meet solids withdrawal requirements.

Jan 1, 1979

By J. L. Huiatt

Kerosine, fuel oil No. 2, vapor oil, and fuel oil No. 6 were separated into general hydrocarbon fractions by ion exchange chromatography and adsorption chromatography. The collecting properties of these fractions were evaluated by flotation of molybdenum and copper minerals from a natural chalcopyrite ore. Paraffin fractions and aromatic fractions of low polarity produced the best molybdenum recoveries. Selective flotation of molybdenite from copper sulfide minerals was not possible with any of the chromatographic fractions.

Jan 1, 1972

By Naeimeh Shabani, Hamid Mirzaie, Javid Sadeghi, Hoda Jafarizadeh-Malmiri, Afshin Javadi

Iron oxide nanoparticles (Fe3O4 NPs), despite their small size, are stable and have a large surface area that allows for absorption and removal of ions as well as turbidity in a short period of time. Thus, the present study addressed the synthesis and characterization of Fe3O4 NPs synthesized using the co-precipitation method and evaluated their effect on the coagulation process in water treatment. The Fe3O4 NPs characteristics were evaluated as follows: magnetic properties were measured using a vibrating sample magnetometer (VSM), surface area using Brunauer–Emmett–Teller (BET), crystal phase using X-ray diffraction (XRD), and morphology using field emission scanning electron microscopy (FESEM). In addition, the effects of the synthetic Fe3O4 NPs on the turbidity reduction of water in various pH levels were evaluated. The synthesized Fe3O4 NPs were without any impurity in the sizes of 22–32 nm, surface area of 99.6 m2/g, pores’ mean diameter size of approximately 10.6 nm, and maximum magnetic saturation of 66.21 emu/gram (emu/g). Using 0.2 g of synthetic Fe3O4 NPs with an initial turbidity of 17 NTU and pH of 6 could reduce all water turbidity (100%). Considering the cheap and facile production and separation, as well as the possibility to reuse them and reduce the sludge water content, iron oxide Fe3O4 NPs can be effectively used for turbidity reduction in the water treatment process.

Oct 26, 2020

By Graham Jones

During 1982 Ash Grove Cement Company contracted with Wagester, Walker, Thornton & Company to convert a Calcimatic rotating hearth kiln at its Portland, Oregon lime plant from gas/oil to coal firing. Increasing costs of natural gas and No. 6 fuel oil made this conversion mandatory if the plant was to remain competitive. Unique features of this project are 1) the distributors of pulverized coal to eighteen small burners around the inner and outer perimeters of the doughnut-shaped kiln, and 2) the attrition-dryer-pulverizer mill. Ash Grove, a century-old lime and cement producer headquartered in Overland Park, Kansas (Kansas City area), looked at various schemes for multiple burner firing before employing Wagester, Walker, Thornton & Company. W.W.T. of Pitts- burgh, Pennsylvania was formed in 1980 by acquiring the Solid Fuels Division of the Pullman Swindell Corporation. This division had been active in developing solid fuel firing for brick tunnel kilns, principally in the Southeast. They continue to supply such systems firing wood waste as well as coal to the brick industry and have also converted two Calcimatic lime kilns for Dixie Lime, Sumterville, Florida, a fluid bed calciner for Texas Gulf in Aurora, North Carolina, and a chrome concentrate kiln for Diamond Chemicals at Castle Hayne, North Carolina. Testing and a proposal have been made for INMETCO, Elwood City, Pennsylvania, on an annular hearth furnace for direct reduction of iron ore to metallic iron.

Jan 1, 1984

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By J. A. Delgadillo, C. A. Pérez-Alonso

"Tumbling mills using balls as grinding media are used extensively in the mining and cement industries to produce fine powders; however, it is well known that the process of size reduction is highly energy-intensive. For this reason, much of today’s comminution research is aimed at understanding grinding mechanisms, by estimating power draft and modeling milling circuits using the discrete element method (DEM). DEM predicts individual particle trajectories, the distribution of energy and contact forces at each collision, lifter wear and power draw. This paper presents a prediction of the discharge particle size distribution using three components, mass balance model (sometimes referred to as a population balance model, PBM), impact energy distribution of the mill obtained from the simulation of the charge motion using DEM and breakage characteristics of particles determined from drop-ball tests. DEM simulation of the charge of a tumbling mill was done using the code MinProSim 1.0 to obtain impact spectra at different operative conditions. Then, the population balance model (PBM), based on impact energy distribution, was used to predict the final particle size distribution in a batch mill and compared with experimental data. It is demonstrated that the DEM-PBM approach allows a reliable solution to predict particle size distribution for tumbling mills. Ideally, the model has to predict size distribution for any operational condition and feed characteristic; however, it has been shown that predictions include some degree of error.IntroductionThe discrete element method (DEM) has recently become a powerful numerical tool that can be used to investigate internal mill charge in ball mills. The early work of Cundall and Strack (1979) used DEM to analyze soil as a discrete medium. Later, the method was improved to simulate the operation of tumbling mills and optimize the design in order to increase the efficiency of energy utilization. Also, it is of great interest to relate ore breakage based on impact energy spectra obtained by DEM simulations and the breakage distribution function used in the PBM to predict particle size distribution in tumbling mills.King and Borgeous (1993) broke single particles in an ultra fast impact load cell to compute the phenomenological parameters in a microscopically more detailed population balance model. Kapur et al. (1997) simulated the size spectra of progeny particles produced by impact grinding as a function of the impact energy. Narayanan (1987), Narayanan and Whiten (1988) and Lira and Kavetsky (1990) estimated the energy-dependent breakage distribution function for scaleup and modeling of industrial ball mills."

Jan 1, 2015