Search Documents

By William C. Peters

The frustration encountered by exploration crews in connection with land acquisition could be graphed to show a correlation with the natural law that everything tends to become more so. Figure I shows a rather common, situation. The combinations of ingredients are almost limitless and the resulting brew is often poisonous to an exploration man. A single step, that of taking a series of deep soil samples is often delayed until some sense can be made from "floating" unpatented claims which are obscure in orientation as well as position, placer claims overlapping lode claims, location posts with empty Prince Albert cans, and claims with no apparent assessment work for ten years. Add to this some patented claims with¬out monuments, a state or federal withdrawal area which may or may not invalidate pre-existing claims, a loosely defined tunnel site, and some ranchers who understandably resent the separation of surface rights from mineral rights. The picture is familiar to exploration men. One approach to such problems is to ignore them until someone voices an objection -- but then an even more chaotic situation is likely to develop. Another practice is to stake new claims to cover all ground that is "open" at first glance and then find out if there are conflicts so that the new claims can be adjusted accordingly.

Jan 1, 1970

By J. W. Butwell

Anaconda has been active In the Bingham mining district near Tooele, Utah since 1914 when the company acquired International Smelting & Refining Co. Over the years both custom ores and complex Pb-Zn-Cu ores from the district were milled and smelted at International. In 1948 Anaconda acquired the property that covers the present Carr Fork ore body. Since that time active exploration took place in the 50's followed by detailed geological evaluation in the 60's. Convinced that high grade Cu deposits would be found at depth, a deep drilling program commenced in the late 60?s, with intersection of the ore zone in 1969. Following extensive deep drilling in the early 70?s, a feasibility study was conducted in 73-74 with board approval given Sept. 6, 1974. The 9,000 t/d mine-mill complex was budgeted at $217 MM over a 5 year schedule with start-up in Sept., 1979. The following discussion includes the concentrator and surface facility portion of the budget or approximately $60 MM of the scope. Special emphasis will be made on equipment selection and layout.

Jan 1, 1980

By Fabio Mielli

Encompassing between 20 and 40 percent of the typical mining operational costs, energy in mining operations is a growing concern for the industry. However, this concern is a complex, multi-faceted variable that involves government regulations, societal pressures, cost and competitiveness. Managing energy efficiency is becoming a keystone of successful companies. The suggested energy strategy in mining and mineral processing operations must follow a well-structured approach to include the following: ? Understanding where energy is being used and why. ? Recommending and implementing energy conservation measures. ? Driving visibility to targets and results. ? Leveraging the energy spent across the enterprise. ? Developing a robust energy and sustainability strategy. Additionally, it must ensure that all decisions support the financial and operational integrity of the business.

Jan 1, 2012

By Margreth Tadie, Chalwe Chibwe

Physicochemical properties of copper electrolytes are a strong fundamental consideration in electrodeposition processes during electro-purification and recovery of copper. Their influence extends to mass transfer as well as energy consumption during the electrodeposition process. In this study, the influence of electrolyte composition on electrolyte physicochemical properties was investigated to review the existing literature data. This review of data is considered necessary as more and more electrowinning models are being developed for process prediction and optimisation and a need of such data is required for accurate prediction of physicochemical properties. The major components of importance to the formation of smooth high-quality and high-purity copper cathodes at optimum current efficiency are considered the species in solution. These include Cu ions, Fe ions (major impurity), H2SO4, and a smoothing agent additive. A 5-factor, 2- and 3-level experimental design was employed to determine the effect of copper (35 and 45 g/l), sulphuric acid (160 and 180 g/l), iron (1, 3, and 6 g/l), polyacrylamide additive (2, 5, and 10 mg/ l), and temperature (45 and 55 °C) on electrolyte density, conductivity, and the diffusion coefficient in synthetic copper electrowinning electrolytes. The major species in a copper electrowinning electrolyte are found to be the most relevant for prediction of physicochemical properties. These results indicate that relatively simple empirical models are sufficient for modelling of the electrolyte domain in electrowinning, without the need for the generation of vast amounts of complex experimental data.

Feb 1, 2021

By P. Hadzeriga

Ion exchange techniques have been growing fast and spectacularly in all phases of Science for the last two decades, but still its acceptance as a unit operation in Metallurgy is resisted. Mainly this is because ion exchange procedures are thought of as glamorous techniques by which only relatively expensive metals are to be recovered. Perhaps this concept comes from the early and basic marriage of uranium and other high price metals and ion exchange procedures. The general trend is that ion exchange technique requires equipment and materials which are too expensive to economically perform a chemical step whenever "cheap" commodities are produced. However, we are here presenting a means of utilization of waste hydrochloric acid by an ion exchange technique. We have studied this from the engineering and economic standpoint in a number of variations of the main procedure discussed here and we-conclude that under proper economic circumstances, the cost of the ion exchange material as well as the equipment and labor involved in the ion exchange section, is by no means unreasonable.

Jan 1, 1964

By Virginia T. McLemore, Devlon R. Shaver

Clinkers are the result of a seam of coal catching fire and burning the surrounding rocks. The fires caused the surrounding rocks to be baked at high temperatures, removing organic material and partially forming glass. These rocks become hard, orange, and brick like, forming clinker. The purpose of the study is to determine their potential to contain economic levels of critical minerals, including Rare Earth Elements. Some clinkers contain over 200 ppm total REE.

Feb 1, 2024

By William C. Baldwin

Unitization and containerization continue to grow with great rapidity throughout the world today. Every industrial nation outside of the Iron Curtain is devoting more and more time toward research of these developing sciences. Unitization and containerization are proving to be the solution to many of modern industry's most pressing handling and shipping problems. Manufacturers make large savings, carriers receive many benefits, and customers take an increasing interest in demanding that their shipments either be unitized or containerized. Unit-loads consist of items, packages or bulk materials pre-assembled into a convenient mass for handling by mechanized equipment and to fit the internal dimensions of carriers. It has been found that unitized handling and shipping offers cost savings too great to be ignored by anyone interested in the distribution of goods. At present, the benefits from unitized shipping and handling are being enjoyed only to a small extent due to the failure of many persons concerned with handling practices in recognizing only some of the advantages of unitization. Before the full benefits of unitized handling and shipping can be realized, some major changes in packaging and distribution practices will be necessary on the part of industry. Numerous investigations in the last two years show conclusively that there are more advantages and more inherent savings for shipping goods on pallets in unit loads than by any other method. There is no question that unit-load handling can offer significant advantages to the user over piece-by-piece package handling. Reduction in handling costs is the primary objective of such activities, but it is by far not the sole objective. Some of the other benefits that can be realized are:

Jan 1, 1973

By S. Tuylu, D. Adiguzel, U. G. Akkaya, A. Bascetin

"One of the main problems for storing of the tailings is acidity occurrence due to several factors such as existence of sulfuric minerals and also the pollution in seepage waters by mobilization of metal ions, which holds great risks in terms of environmental regulations. Because of these specified reasons, tailing materials to be used in a SPD formula should have comply with some specifications. Among these properties; oxygen content, temperature, matrix suction and pH are the most important parameters. In the study, the relationships between the parameters mentioned are investigated to reveal optimum paste design layout. The lowest amount of seepage water obtained from the paste layers in the pilot cabinet was found as 2150 ml from 3rd layer. As for the maximum seepage water and the average of the all 11 layers were found as 4909 ml from 6th layer and 3273 ml respectively. The reactions occurring according to the oxidation, as seen at seepage water of second and third layers, decreased the pH of system to the under of 7 value. Additionally, when the seepage water of first layer’s EC value is 2.93 mS/cm, the EC value of second layer is increased at 3.54 mS/cm. The other parameters are evaluated with the obtained results of the tests to determine the optimum storing conditions for SPD.INTRODUCTION Conventional waste disposal methods, although widely used, pose great environmental risks. One of the most important issues is acid mine drainage (AMD). Tailings of metallic mines contain heavy metals, aggressive chemicals and hazardous materials. In the presence of oxygen and water, an oxidation reaction can occur, causing a decrease in pH of the environment, and heavy metals that are present in the environment can dissolve easily. Subsequently, heavy metals can pollute underground water basins, creating a great amount of danger for the ecology and potable water resources. Another important risk associated with conventional waste disposal methods is accidents related to the waste dam. Higher volumes of water and tailings (usually 15% solids and 85% water by weight) are sent to waste dams, making it very difficult to control the stability of the dam under conditions such as static and dynamic loads (seismic activities, vibrations caused by blasting, etc.), flooding, and seepage. In case of an accident or failure, the spread of great amounts of mud containing hazardous chemicals and heavy metals can harm the environment of the dam site significantly (Bascetin et al., 2014). In the paste technology, depending on the type of ore, tailings used in the paste mixture can contain sulphide minerals (such as pyrite and pyrrhotite). These minerals are known to be reactive with water and oxygen to produce acidity (sulphuric acid)."

Jan 1, 2015

By P. Somasundaran

Electrochemical properties of silicate minerals govern their behavior in processes such as flocculation and enhanced oil recovery that can occur at elevated temperatures. Knowledge of these properties as a function of temperature can be helpful in developing an under- standing of the role of these interfacial properties at non-ambient temperatures. Zeta potential of Sodium Kaolinite and quartz has been determined as a function of pH and temperature in this work. Both systems exhibited markedly different behavior at higher temperatures and also exhibited significant hysteresis. Results are examined in terms of possible dissolution of the minerals and surface reactions at different temperatures.

Jan 1, 1986

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By John E. Caffrey

Mr. William. J. Montgomery in his book "Theory and Practice on Mine Ventilation stated "Ventilation is vitally important to underground mining for three reasons: First, it sweeps all workings with a plentiful supply of air and drives to the outside the smoke, gases, and contaminated air which would be injurious to the miners; second, it dilutes and renders harmless the explosive gases emitted from the strata, thus eliminating the dangerous conditions caused by the accumulation of these gases; third, it keeps the mine air as nearly as possible of the same composition as the outside air, thus giving to the miner the healthiest possible condition in which to work...." Specific methods to achieve the above basic reasons for mine ventilation were established in the Federal Coal Mine Health and Safety Act of 1969. Sections 303(y)(1); (y)(2), and Section 317(f)(4) of the Act, which can be broadly described as entrapment features, are controversial and debatable in the minds of many mining engineers in their intent and method for affecting, 303(y)(1) in certain cases prohibits the use of belt haulage entries as an intake for face ventilation, This is to say that air traveling in a belt entry will be placed into the returns and not used for face ventilation, 303(y)(2) limits the velocity of the air on trolley haulage entries. The regulations, as published in the Federal Register, have set this limit at 250 feet per minute unless a higher velocity is approved by the District Manager.

Jan 1, 1972

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

The understanding of the influence of the different types of apatite on the performance of mineral processing of igneous phosphate ores is still a challenge due to the difficulty to explain why some types of apatite floats in the froth flotation cell and others do not under the same conditions. Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão mine: predominantly blue apatite, followed by green apatite and less frequently yellow apatite. The chemical composition of these types of apatite was determined by electron microprobe analysis (EPMA) and LA-ICP-MS. Blue and green apatite respond well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite is the one bearing the lowest P2O5 content and the largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest P and Ca grades and lowest substitution level. A negative correlation of the amount of phosphorus with fluorine was observed. Furthermore, impregnation of iron oxide-hydroxides in the yellow apatite was also observed. Therefore, the low flotation behaviour is due to low crystallinity coupled with impregnation onto its surface.

Jan 31, 2022

By R. Scheffel, R. Washnock, G. Zarate

"The second survey of global copper leaching operations has been completed, the data published in 1998 has been updated. A survey questionnaire was sent to 40 identified copper leach operations around the world including those leach properties still in operation that responded to the 1998 survey. This paper lists the results of 26 operations that responded to the survey. Selected information from the survey is represented in graphical form. INTRODUCTION Copper leaching was first performed by truck dumping huge monolithic stockpiles of ore and flooding the surface with leach solution or lixiviant with little understanding to the parameters that support optimum recovery of the metal. Heap leaching has evolved into a controlled process whereby a complex low grade ore is stacked in shallow lifts (under 10 m in most cases). The ore is usually crushed and agglomerated, conveyor stacked on an engineered containment system (leach pad) and irrigated in a controlled manner. The lixiviant chemistry is designed to extract the optimum amount of metal from the ore. At first glance, heap leaching appears to be simple in nature. In fact, it is a very complex process. A plethora of technologies such as material handling, environmental control, analytical techniques, solution chemistry, hydrology and many others contribute to the design and operation of a heap leach. Heap leaching requires an inter-disciplinary approach between geologists, mining engineers and metallurgists. Many operational factors affect heap leaching. The process must address climatic factors, flexible operation, quality control before and after leaching, physical characteristics of the ore, geology, mineralogy, reagent consumption, solution application rate and methods (wobblers or emitters), particle size, and favorable conditions for bacterial growth and survival. Predicting, troubleshooting, and optimization of leach recovery is a significant challenge when considering the number of variables involved and their interactions The survey updates many of these key operating parameters to the current state of the art. It should provide the reader an excellent benchmarking summary of these factors on a site-by-site basis."

Jan 1, 2016

By Jerry Williams

GEORGE WEINMAN: At this time, our co-chair, Jamie Davis from Phelps Dodge, will come to the podium. JAMIE DAVIS: Our next speaker is Jerry Williams from Phelps Dodge, Morenci. Jerry is the maintenance planning supervisor and is in charge of preventative maintenance and maintenance scheduling. Jerry's group uses predictive tools to monitor and predict the equipment failure throughout the mine, from pumps to shovels to motors, you name it. The title of Jerry's talk is "If You're Not Using Predictive Tools, You're Behind the Curve." I’ll turn it over to Jerry.

Jan 1, 1998

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By J. W. MacDonald

Two coal mine shafts recently completed in Franklin County, Ill., afford experience and accomplishment to warrant review, These shafts provide access to a tract with a potential recovery of one hundred million tons. This work provided the initial sinking by other than a contractor's organization since 1918. Four additional shafts required during the interim were sunk under contract arrangement with others. Supervisory contact and inspection afforded experience to govern planning and conduct of the recent work.

Jan 1, 1960

By A. E. Michon

I am Alfred E. Michon, Vice President- International for Burlington Northern Inc. I work for BN's holding company and my responsibilities include co-ordinating the activities of our eight subsidiary companies as they relate to international commerce--an increasingly important aspect of the overall business of our company. Until last April, I was President of the Fort Worth and Denver and Colorado and Southern railroads, subsidiaries of BN. Prior to that, I headed the marketing and pricing area of BN's coal transportation business. Based on my experience in the energy industry, both domestic and international, I would like to discuss the world-wide trend towards the reliance on low-sulfur coal in lieu of natural gas and oil for the generation of electricity. Since pontification on the energy scene world- wide is best left to consultants with scenario-spitting computers, let me in- stead emphasize this trend through two examples. First I will describe the regulatory and economic factors which have encouraged the replacement of natural gas by low sulfur coal as a boiler fuel in the US. BN's investments in track and equipment were instrumental in this conversion. Secondly, I will show how this same combination of factors has created a large demand for steam coal in the Far East. Again, our company's strategy is to facilitate conversion to coal overseas through timely and sufficient investments.

Jan 1, 1982

By Wen H. Su

This paper examines the intrinsic mechanisms of cutter roof by combining field investigation, laboratory testings, underground instrumentations, and numerical modelling. Cutter roof developed during the development of a set of longwall panel entries in a West Virginia coal mine was presented as a case study. Mining alternatives applicable to the mine are recommended. Cutter roof occurred in two other West Virginia coal mines were also investigated Detailed comparisons were made among the three cases. As a result of the extensive investigation, intrinsic mechanisms of cutter roof failures under various conditions are presented from the practical and theoretical points of view.

Jan 1, 1985

By O. Alonso-Gonzalez, F. Nava-Alonso, A. Uribe-Salas, C. Jimenez-Velasco

"Most of the gold produced worldwide is still obtained by cyanidation, in spite of the difficulties encountered in the processing of some gold ores such as the dissolution of copper-bearing minerals in cyanide solutions. The leached copper forms complexes with cyanide and causes several operating problems, which have led to the development of copper removal/recovery processes, among them the industrially accepted SART process (sulfidization, acidification, recycling and thickening). Although the SART process is in use in gold production plants around the world, new challenges are appearing with the continuous varying of the mineralogy of ores (such as higher copper grades, changing the solution composition and complexity). The optimal SART operating conditions for a specific solution are not the same when the composition of the solution changes; consequently, the efficiency of this process can decrease.The present study is a thermodynamic approach, corroborated by laboratory experiments, to explain how the main variables of the process affect the efficiency of copper precipitation as cuprous sulfide (Cu2S). The variables considered were pH value, copper concentration, cyanide/copper molar ratio and sulfur/copper molar ratio, all of which werevaried within the limits encountered in typical cyanidation solutions presenting the problem of copper.It was found that the variable that most affects the efficiency of the process was the pH value, since poor or no control of it can cause cuprous sulfide redissolution. The S/Cu molar ratio is also important: raising this ratio increases copper removal, but high ratios will also cause sulfide and cyanide losses. The effect of changing the CN/Cu molar ratio was negligible between 4 and 8. For a solution containing 300 mg/L copper and 490 mg/L cyanide, copper removal as high as 98.8% can be obtained with the addition of 0.6 moles of sulfide per mole of copper at pH = 6.IntroductionThe main process for gold production is cyanidation, because it is the most economical and efficient process so far. Precious-metal leaching occurs when the ore is placed in contact with a dilute alkaline cyanide solution. The dissociation of cyanide salts provides free cyanide ions, which allow the formation of the aurocyanide complex Au(CN)2 -. This complex can be retrieved from the solution by adsorption on activated carbon or by zinc precipitation. Although the use of cyanide represents an issue to health and the environment, there are technologies for its management and treatment that can be easily applied. Furthermore, it is a low-cost process compared with other methods that are available or under development."

Jan 1, 2015

By Bill Dershowitz

Consider a deep gold orebody with grade of 4 g/t (0.11 oz/st). At the time of this writing, with gold prices at historic highs, it could be a good, but not great, prospect. But if it is a vein deposit, and those veins are 200 g/t (5.8 oz/st), it would be significantly more attractive if there was a way to produce directly from those veins, leaving the rest of the rock in place. [Figure 1 The red around each of the four injector wells shows areas of high pressure, where the lixiviant fluid is pumped into the rock mass, with orange and yellow indicating dissipated pressure. The black lines indicate some of the fracture pathways through which the lixiviant, with absorbed metal, flows toward the central recovery well where low pressure is indicated in blue. Lixiviant is pumped out through the recovery well. Image courtesy of Golder Associates.] There is a way to do this, in situ leach (ISL) or solution mining. It has been a viable commercial technology for more than five decades.

Jan 1, 2011